Scribd
Upload
2K views3 pages

Fanuc 10M CNC Parameter Guide

This document provides configuration settings for connecting a FactoryWiz DNC system to a Fanuc 10M CNC control. It lists parameters that need to be verified and set on the CNC including communication settings, program identifiers, and remote commands. It also describes how to output and input CNC programs and provides a wiring diagram between the DB-9 and DB-25 ports including pinouts and jumper settings for RTS/CTS handshaking.

Uploaded by

Le Hoang Hiep
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views3 pages

Fanuc 10M CNC Parameter Guide

This document provides configuration settings for connecting a FactoryWiz DNC system to a Fanuc 10M CNC control. It lists parameters that need to be verified and set on the CNC including communication settings, program identifiers, and remote commands. It also describes how to output and input CNC programs and provides a wiring diagram between the DB-9 and DB-25 ports including pinouts and jumper settings for RTS/CTS handshaking.

Uploaded by

Le Hoang Hiep
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
  • CNC Parameters
  • Wiring Diagram

DNC Systems

CNC Configuration Sheet

Fanuc 10M
CNC Parameters:
You will need to verify all parameters listed below that correspond to your CNC control. These parameters may not match
your particular machine’s control. Document (Phone camera) original settings before making modifications!

Setting screen:
Punch code- 1=ISO
TV CHECK=0 OFF

Under Service page:


0000 = xxx01000 (ISO)
0020 = 2 (Input device Foreground)
0021 = 2 (Output device Foreground)
0022 = 2 (Input device Background)
0023 = 2 (Output device Background)

5001 to 1 (Device Select)


5002 to 2 (RS232 Device Select)
5110 to 3 (Device type DC Codes used)
5111 to 1 (1 stop bit)
5112 to 10 (4800 baud) 11=9600, 9=2400, 8=1200 7=600 6=300

FactoryWiz DNC Settings:


Basic Communication
1.01- Port Type: Standard
1.11- Baud: 4800
1.12- Data Bits: 7
1.13- ASCII Even
1.14- Stop Bits: 1
1.15- Handshake: XON/XOFF

Sending Options
2.11- Leader: %<10>
2.12- Trailer: %
2.23- Skip lines that contain: %
2.31- Automatic timeout: 7

Receiving Options
3.11- Program identifier 1: O
3.12- Program Identifier 2: :
3.21- Receive timeout: 3
3.31- Ignore data before first end-of-block: True
3.32- Ignore data after last end-of-block: True

Remote Commands
Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA 95119
408.224.9167 | [Link]
4.02- Request for file command: GET-
4.03- Request for file command (drip feed): DNC-
4:11- Request to save command: PUT-

Additional Notes:
Changing CNC Parameters:

System (Param) screen:


To set parameters, move dial to MDI mode on machine.
Press SETTINGS key. Change PWE (#8000) to 1. The CNC will alarm.

Outputting CNC Programs:


To output a program, set the CNC to "edit" mode. Press the PROG key on the control panel. Use the right
arrow (Page) key until PUNCH appears. Press PUNCH, then Press THIS.

Inputting CNC Programs:


To input a program, set the CNC to "edit" mode. Press the PROG key on the control panel. Use the right
arrow(Page)keys until READ appears. Press READ, then press ALL.

Wiring Diagram:
Pinout includes RTS/CTS Handshaking

DB-9 com port Wire color DB-25 CNC Jumper?

(Disconnected) Shield 1

2 (Receive Data) Green 2 (Transmit Data)

3 (Transmit Data) Red 3 (Receive Data)

5 (Signal Ground) Black 7 (Signal Ground)

7 (RTS) Brown 5 (CTS)

8 (CTS) Blue 4 (RTS)

6 (DSR) JUMPER

8 (DCD)

20 (DTR)

Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA 95119
408.224.9167 | [Link]
Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA 95119
408.224.9167 | [Link]

Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA 95119 408.224.9167 | www.factorywiz.com
Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA 95119 408.224.9167 | www.factorywiz.com 4.
Refresh Your Memory, Inc. | 6920 Santa Teresa Blvd Suite 201 | San Jose, CA 95119 408.224.9167 | www.factorywiz.com

You might also like