Scribd
Upload
3K views1 page

Breakdown Mechanisms in Solid Dielectrics

The document discusses four types of intrinsic breakdown in dielectric materials: 1. Intrinsic breakdown occurs when a pure, homogeneous dielectric is subjected to a very short high voltage, reaching its maximum intrinsic strength. This depends on the material's structure and temperature conditions. 2. Thermal breakdown happens when heat generated from conduction and polarization exceeds heat dissipated, causing the material to overheat and break down. Different electric fields correspond to different heating curves. 3. Electrochemical breakdown reduces strength when cavities form, allowing gas breakdown and chemical degradation from discharge products to slowly erode the material. 4. Electromechanical breakdown results when attractive forces between induced surface charges exceed the material's mechanical strength, causing it

Uploaded by

Hypnotic Knight
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views1 page

Breakdown Mechanisms in Solid Dielectrics

The document discusses four types of intrinsic breakdown in dielectric materials: 1. Intrinsic breakdown occurs when a pure, homogeneous dielectric is subjected to a very short high voltage, reaching its maximum intrinsic strength. This depends on the material's structure and temperature conditions. 2. Thermal breakdown happens when heat generated from conduction and polarization exceeds heat dissipated, causing the material to overheat and break down. Different electric fields correspond to different heating curves. 3. Electrochemical breakdown reduces strength when cavities form, allowing gas breakdown and chemical degradation from discharge products to slowly erode the material. 4. Electromechanical breakdown results when attractive forces between induced surface charges exceed the material's mechanical strength, causing it

Uploaded by

Hypnotic Knight
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

1.

Intrinsic Breakdown
If the dielectric material is pure and homogeneous, the temperature and environmental conditions
suitably controlled and if the voltage is applied for a very short time of the order of 108 second, the
dielectric strength of the specimen increases rapidly to an upper limit known as intrinsic dielectric
strength.
The intrinsic strength, therefore, depends mainly upon the structural design of the material i.e., the
material itself and is affected by the ambient temperature as the structure itself might change slightly
by temperature condition. In order to obtain the intrinsic dielectric strength of a material, the samples
are so prepared that there is high stress in the centre of the specimen and much low stress at the corners
as shown in Fig.

Specimen designed for intrinsic breakdown


2. Thermal Breakdown
When an insulating material is subjected to an electric field, the material gets heated up due to conduction
current and dielectric losses due to polarization. The conductivity of the material increases with increase in
temperature and a condition of instability is reached when the heat generated exceeds the heat dissipated by the
material and the material breaks down. Fig. 1.17 shows various heating curves corresponding to different
electric stresses as a function of specimen temperature. Assuming that the temperature difference between the
ambient and the specimen temperature is small, Newtons law of cooling is represented by a straight line.

Thermal stability or instability of different fields

3. Electrochemical Breakdown
Whenever cavities are formed in solid dielectrics, the dielectric strength in these solid specimen de- creases.
When the gas in the cavity breaks down, the surfaces of the specimen provide instantaneous anode and
cathode. Some of the electrons dashing against the anode with sufficient energy shall break the chemical
bonds of the insulation surface. Similarly, positive ions bombarding against the cathode may increase the
surface temperature and produce local thermal instability. Similarly, chemical degra- dation may also occur
from the active discharge products e.g., O3, NO2 etc. formed in air. The net effect of all these processes is a
slow erosion of the material and a consequent reduction in the thickness of the specimen. Normally, it is
desired that with ageing, the dielectric strength of the specimen should not decrease.

4. Electromechanical Breakdown
When a dielectric material is subjected to an electric field, charges of opposite nature are induced on the
two opposite surfaces of the material and hence a force of attraction is developed and the speciment is
subjected to electrostatic compressive forces and when these forces exceed the mechanical withstand
strength of the material, the material collapses.

You might also like