Project Job Ref.
Section Sheet no./rev.
1
Calc. by Date Chk'd by Date App'd by Date
H 6/25/2024
PILE CAP ANALYSIS & DESIGN (ACI318-19 (22))
In accordance with ACI318-19 (22)
Tedds calculation version 2.0.14
Design summary - PASS (0.891)
Pile analysis summary
Unit Applied Allowable Utilization Result
Pile axial compression, pile 1 kips 132 600 0.220 PASS
Pile cap design summary
Unit Required Provided Utilization Result
Flexural reinforcement in2 15.5 (min) 17.4 0.891 PASS
One way modified shear kips 319.2 1722.7 0.185 PASS
Two way column shear psi 0 104.4 0 PASS
Two way col. mod. shear psi 86.9 447.8 0.194 PASS
Two way pile shear psi 23.5 104.4 0.225 PASS
One way corner pile shear kips 186.9 210.5 0.888 PASS
4 5
11' 2"
1 2
11' 2"
;
Project Job Ref.
Section Sheet no./rev.
2
Calc. by Date Chk'd by Date App'd by Date
H 6/25/2024
64"
4"
x
Pile cap details
Pile cap width, along x axis; Lx = 11.197 ft
Pile cap width, along y axis; Ly = 11.197 ft
Total cap depth; Dcap = 64 in
Density of concrete; conc = 150 lb/ft3
Height of soil above pile cap; hsoil = 0 in
Density of soil above pile cap; soil = 80 lb/ft3
Pile cap area; Acap = Lx Ly = 18054.44 in2
Column details
Column width, along x axis; lx,col = 32 in
Column width, along y axis; ly,col = 32 in
Column location, x axis; xc = 5.58 ft
Column location, y axis; yc = 5.58 ft
Pile details
Pile material; Steel
Steel pile section; HP 14x89
Allowable axial compression load; PpC,allow = 600 kips
Allowable axial tension load; PpT,allow = 0 kips
Allowable lateral load; Vp,allow = 0 kips
Number of piles; Np = 5
Pile embedment; dembed = 4 in
Pile spacing; sp = 44.1 in
Edge distance; E = 36 in
Column axial loads
Axial dead load; PD = 200 kips
Project Job Ref.
Section Sheet no./rev.
3
Calc. by Date Chk'd by Date App'd by Date
H 6/25/2024
Total area axial dead load; PD,area = conc Lx Ly Dcap = 100.302 kips
Axial live load; PL = 350 kips
Pile group centroid
Centroid location, x direction; xpg,c = (xp1 + xp2 + xp3 + xp4 + xp5) / Np = 5.599 ft
Centroid location, y direction; ypg,c = (yp1 + yp2 + yp3 + yp4 + yp5) / Np = 5.599 ft
Pile distance from centroid
Pile 1 centroid distance, x direction; xp1,c = xp1 - xpg,c = -2.599 ft
Pile 1 centroid distance, y direction; yp1,c = yp1 - ypg,c = -2.599 ft
Pile 2 centroid distance, x direction; xp2,c = xp2 - xpg,c = 2.599 ft
Pile 2 centroid distance, y direction; yp2,c = yp2 - ypg,c = -2.599 ft
Pile 3 centroid distance, x direction; xp3,c = xp3 - xpg,c = 0 ft
Pile 3 centroid distance, y direction; yp3,c = yp3 - ypg,c = 0 ft
Pile 4 centroid distance, x direction; xp4,c = xp4 - xpg,c = -2.599 ft
Pile 4 centroid distance, y direction; yp4,c = yp4 - ypg,c = 2.599 ft
Pile 5 centroid distance, x direction; xp5,c = xp5 - xpg,c = 2.599 ft
Pile 5 centroid distance, y direction; yp5,c = yp5 - ypg,c = 2.599 ft
Moment of inertia of pile group
Moment of inertia about x-x axis; Ixx = yp1,c2 + yp2,c2 + yp3,c2 + yp4,c2 + yp5,c2 = 27.01 ft2
Moment of inertia about y-y axis; Iyy = xp1,c2 + xp2,c2 + xp3,c2 + xp4,c2 + xp5,c2 = 27.01 ft2
Loading eccentricity
Eccentricity of column load, x direction; ex,c = xc - xpg,c = -0.02 ft
Eccentricity of column load, y direction; ey,c = yc - ypg,c = -0.02 ft
Dead load pile forces
Dead load moment about x-x axis; MxD,Des = (-1) PD ey,c = 3.72 kip_ft
Dead load moment about y-y axis; MyD,Des = PD ex,c = -3.72 kip_ft
Dead axial load on pile 1; Pp1,D = (PD + PD,area) / Np + MyD,Des xp1,c / Iyy + MxD,Des (-1) yp1,c / Ixx =
60.78 kips
Dead axial load on pile 2; Pp2,D = (PD + PD,area) / Np + MyD,Des xp2,c / Iyy + MxD,Des (-1) yp2,c / Ixx =
60.06 kips
Dead axial load on pile 3; Pp3,D = (PD + PD,area) / Np + MyD,Des xp3,c / Iyy + MxD,Des (-1) yp3,c / Ixx =
60.06 kips
Dead axial load on pile 4; Pp4,D = (PD + PD,area) / Np + MyD,Des xp4,c / Iyy + MxD,Des (-1) yp4,c / Ixx =
60.06 kips
Dead axial load on pile 5; Pp5,D = (PD + PD,area) / Np + MyD,Des xp5,c / Iyy + MxD,Des (-1) yp5,c / Ixx =
59.34 kips
Live load pile forces
Live load moment about x-x axis; MxL,Des = (-1) PL ey,c = 6.52 kip_ft
Live load moment about y-y axis; MyL,Des = PL ex,c = -6.52 kip_ft
Live axial load on pile 1; Pp1,L = PL / Np + MyL,Des xp1,c / Iyy + MxL,Des (-1) yp1,c / Ixx = 71.25 kips
Live axial load on pile 2; Pp2,L = PL / Np + MyL,Des xp2,c / Iyy + MxL,Des (-1) yp2,c / Ixx = 70 kips
Live axial load on pile 3; Pp3,L = PL / Np + MyL,Des xp3,c / Iyy + MxL,Des (-1) yp3,c / Ixx = 70 kips
Live axial load on pile 4; Pp4,L = PL / Np + MyL,Des xp4,c / Iyy + MxL,Des (-1) yp4,c / Ixx = 70 kips
Live axial load on pile 5; Pp5,L = PL / Np + MyL,Des xp5,c / Iyy + MxL,Des (-1) yp5,c / Ixx = 68.75 kips
Project Job Ref.
Section Sheet no./rev.
4
Calc. by Date Chk'd by Date App'd by Date
H 6/25/2024
ASCE 7-22 load combinations (ASD)
1.0D (0.101)
1.0D + 1.0L (0.220)
Combination 2 results: 1.0D + 1.0L
Pile 1 axial load; Pp1 = 1.0 Pp1,D + 1.0 Pp1,L = 132.03 kips
max(Pp1 / PpC,allow,0) = 0.220
PASS - Pile allowable compression load exceeds axial force
Pile cap design
Material details
Compressive strength of concrete; f'c = 4000 psi
Concrete type; Normal weight
Concrete modification factor; =1
Yield strength of reinforcement; fy = 60000 psi
Compression-controlled strain limit ([Link]) ty = 0.002
Nominal cover to top reinforcement; cnom,top = 2.5 in
Nominal cover to bottom reinforcement; cnom,bot = 2.5 in
ASCE 7-22 load combinations (LRFD)
1.4D (0.891)
1.2D + 1.6L + 0.5Lr (0.891)
Combination 2 results: 1.2D + 1.6L + 0.5Lr
Moment design, about x-x axis, positive moment
Ultimate bending moment; Mu = 461.668 kip_ft
Tension reinforcement provided; 22 No.8 bot bars (6 in c/c)
Area of tension reinforcement provided; [Link] = 17.38 in2
Minimum area of reinforcement ([Link]); [Link] = 0.0018 Lx Dcap = 15.479 in2
PASS - Area of reinforcement provided exceeds minimum
Maximum spacing of reinforcement ([Link]); smax = min(2 Dcap, 18 in) = 18 in
PASS - Maximum permissible reinforcement spacing exceeds actual spacing
Depth to tension reinforcement; d = Dcap - dembed - cnom,bot - [Link] / 2 = 57.000 in
Depth of compression block; a = [Link] fy / (0.85 f'c Lx) = 2.283 in
Neutral axis factor; 1 = 0.85
Depth to neutral axis; c = a / 1 = 2.685 in
Strain in tensile reinforcement ([Link]); t = 0.003 d / c - 0.003 = 0.06068
Minimum tensile strain ([Link]) min = ty + 0.003 = 0.00500
PASS - Tensile strain exceeds minimum required
Nominal moment capacity; Mn = [Link] fy (d - a / 2) = 4854.121 kip_ft
Flexural strength reduction factor; f = min(max(0.65 + 0.25 (t - ty) / (0.003), 0.65), 0.9) = 0.900
Design moment capacity; Mn = f Mn = 4368.709 kip_ft
Mu / Mn = 0.106
PASS - Design moment capacity exceeds ultimate moment load
One-way shear design at column face, along x axis, right side
Ultimate shear force at face of column; Vu = 319.23 kips
Project Job Ref.
Section Sheet no./rev.
5
Calc. by Date Chk'd by Date App'd by Date
H 6/25/2024
Ultimate moment force at face of column; Mu = 461.668 kip_ft
Depth to reinforcement; dv = [Link] = 56 in
Distance to nearest pile; wR = 15.407 in
Size effect factor ([Link].3); s = min((2 / (1 + (dv / 1 in) / 10)),1.0) = 0.55
Ratio of longitudinal reinforcement; w = [Link] / (Ly [Link]) = 0.002
Shear strength reduction factor; v = 0.75
Nominal shear capacity (CRSI Section 5.3); Vn = min((dv / (wR + etolerance)) (3.5 - 2.5 min(1.0,Mu / (Vu dv))) (8 s
(w)1/3 (f'c 1 psi)),10 (f'c 1 psi)) Ly dv = 2296.939 kips
Design shear capacity; Vn = v Vn = 1722.704 kips
Vu / Vn = 0.185
PASS - Design shear capacity exceeds ultimate shear load
Column two way shear design
Depth to reinforcement; dv2 = 56 in
Size effect factor ([Link].3) s = min((2 / (1 + (dv2 / 1 in) / 10)),1.0) = 0.55
Shear perimeter length; lx,perim = 110.960 in
Shear perimeter width; ly,perim = 111.407 in
Shear perimeter (22.6.4); bo = lx,perim + ly,perim = 222.367 in
Area inside shear perimeter; AInsidePerim = lx,perim ly,perim = 12361.701 in2
Ultimate shear load; Vu = 0 kips = 0.000 kips
Ultimate shear stress from vertical load; vug = max(Vu / (bo dv2),0 psi) = 0.000 psi
Column geometry factor (Table [Link]); = ly,col / lx,col = 1.00
Column location factor ([Link]); s =20
Concrete shear strength ([Link]); vcpa = (2 + 4 / ) s (f'c 1 psi) = 208.893 psi
vcpb = (s dv2 / bo + 2) s (f'c 1 psi) = 244.987 psi
vcpc = 4 s (f'c 1 psi) = 139.262 psi
vcp = min(vcpa,vcpb,vcpc) = 139.262 psi
Shear strength reduction factor; v = 0.75
Nominal shear stress capacity (Eq. [Link]); vn = min(vcpa,vcpb,vcpc) = 139.262 psi
Design shear stress capacity ([Link](d)); vn = v vn = 104.447 psi
vug / vn = 0.000
PASS - Design shear capacity exceeds ultimate shear load
Column modified two way shear design
Depth to reinforcement; dv2 = 56 in
Size effect factor ([Link].3) s = min((2 / (1 + (dv2 / 1 in) / 10)),1.0) = 0.55
Distance to closest pile, x direction; wx = 15 in
Distance to closest pile, y direction; wy = 15 in
Shear perimeter length; lx,perim = 32 in
Shear perimeter width; ly,perim = 32 in
Shear perimeter, modified (CRSI 5.3); bs = 2 lx,perim + 2 ly,perim = 128.000 in
Area inside shear perimeter; AInsidePerim = lx,perim ly,perim = 1024.000 in2
Ultimate shear load; Vu = abs(Sum(Pp1,LRFD2,Pp2,LRFD2,Pp4,LRFD2,Pp5,LRFD2) - 1.2 (conc Dcap)
(Acap - AInsidePerim)) = 622.754 kips
Ultimate shear stress from vertical load; vumod = max(Vu / (bs dv2),0 psi) = 86.880 psi
Project Job Ref.
Section Sheet no./rev.
6
Calc. by Date Chk'd by Date App'd by Date
H 6/25/2024
Equivalent shear perimeter, traditional; bo = bs + 4 dv2 = 352.000 in
Column geometry factor (Table [Link]); = ly,col / lx,col = 1.00
Column location factor ([Link]); s =40
Concrete shear strength, traditional ([Link]); vcpa = (2 + 4 / ) s (f'c 1 psi) = 208.893 psi
vcpb = (s dv2 / bo + 2) s (f'c 1 psi) = 291.184 psi
vcpc = 4 s (f'c 1 psi) = 139.262 psi
vcp = min(vcpa,vcpb,vcpc) = 139.262 psi
Concrete shear strength, modified (CRSI 5.3); [Link] = min((dv2 / (2 (average(wx,wy) + etolerance))) (bo / bs) vcp, 32
(f'c 1 psi)) = 597.059 psi
Shear strength reduction factor; v = 0.75
Nominal shear stress capacity (Eq. [Link]); vn = [Link] = 597.059 psi
Design shear stress capacity ([Link](d)); vn = v vn = 447.794 psi
vumod / vn = 0.194
PASS - Design shear capacity exceeds ultimate shear load
Pile two way shear design, pile 1
Depth to reinforcement; dv2 = 56 in
Size effect factor ([Link].3) s = min((2 / (1 + (dv2 / 1 in) / 10)),1.0) = 0.55
Shear perimeter length; lx,perim = 71.350 in
Shear perimeter width; ly,perim = 70.900 in
Shear perimeter (22.6.4); bo = lx,perim + ly,perim = 142.250 in
Ultimate shear load; Vu = abs(Pp1,LRFD2) = 186.938 kips
Ultimate shear stress from vertical load; vug = max(Vu / (bo dv2),0 psi) = 23.467 psi
Pile geometry factor (Table [Link]); = lx,pile / ly,pile = 1.07
Pile location factor ([Link]); s =20
Pile shear strength ([Link]); vcpa = (2 + 4 / ) s (f'c 1 psi) = 200.367 psi
vcpb = (s dv2 / bo + 2) s (f'c 1 psi) = 343.750 psi
vcpc = 4 s (f'c 1 psi) = 139.262 psi
vcp = min(vcpa,vcpb,vcpc) = 139.262 psi
Shear strength reduction factor; v = 0.75
Nominal shear stress capacity (Eq. [Link]); vn = min(vcpa,vcpb,vcpc) = 139.262 psi
Design shear stress capacity ([Link](d)); vn = v vn = 104.447 psi
vug / vn = 0.225
PASS - Design shear capacity exceeds ultimate shear load
One-way corner pile shear design, pile 1
Ultimate shear force; Vu = abs(Pp1,LRFD2) = 186.938 kips
Depth to reinforcement; dv2 = min([Link],[Link]) = 56 in
Width of design section; b = (min(yp1,Ly - yp1) + min(xp1,Lx - xp1) + (dp / 2 + min(dv2,13 in) - etolerance) /
sin(45 deg)) / sin(45 deg) = 136.5 in
Size effect factor ([Link].3); s = min((2 / (1 + (dv2 / 1 in) / 10)),1.0) = 0.55
Ratio of longitudinal reinforcement; wx = [Link] / (Ly [Link]) = 0.002
wy = [Link] / (Lx [Link]) = 0.002
wxy = (wx wy)0.5 = 0.002
Shear strength reduction factor; v = 0.75
Project Job Ref.
Section Sheet no./rev.
7
Calc. by Date Chk'd by Date App'd by Date
H 6/25/2024
Nominal shear capacity (Table [Link]); Vn = min(8 s (wxy)1/3 (f'c 1 psi) b dv2, 5 (f'c 1 psi)
b dv2) = 280.651 kips
Design shear capacity; Vn = v Vn = 210.488 kips
Vu / Vn = 0.888
PASS - Design shear capacity exceeds ultimate shear load
22 No.8 bot bars (6 in c/c)
11' 2"
22 No.8 bot bars (6 in c/c)
y
11' 2"
