Current Transducer LA 205-S/SP1 IPN = 200 A

For the electronic measurement of currents : DC, AC, pulsed...,

16140
Electrical data
IPN Primary nominal r.m.s. current 200 A Features
IP Primary current, measuring range 0 .. ± 300 A
ÎP max Measuring overload 1) 600 A • Closed loop (compensated) current
RM Measuring resistance @ TA = 70°C TA = 85°C transducer using the Hall effect
RM min RM max RM min RM max • Insulated plastic case recognized
according to UL 94-V0
with ± 12 V @ ± 200 A max 0 68 0 66 Ω
@ ± 300 A max 0 33 0 30 Ω • Patent pending.
with ± 15 V @ ± 200 A max 5 95 5 93 Ω
@ ± 300 A max 5 50 5 49 Ω Special feature
ISN Secondary nominal r.m.s. current 100 mA • Connection to secondary circuit on
KN Conversion ratio 1 : 2000 Faston 6.3 x 0.8 mm.
VC Supply voltage (± 5 %) ± 12 .. 15 V
IC Current consumption 20 (@ ± 15 V ) + IS m A Advantages
Vb R.m.s rated voltage 2), safe separation 1625 V
basic isolation 3250 V • Excellent accuracy
• Very good linearity
Accuracy - Dynamic performance data • Low temperature drift
XG Overall accuracy @ IPN , TA = 25°C ± 0.8 % • Optimized response time
ε L
Linearity error < 0.1 % • Wide frequency bandwidth
• No insertion losses
Typ Max
• High immunity to external
IO Offset current @ IP = 0, TA = 25°C ± 0.15 mA
interference
IOM Residual current 3) @ IP = 0, after an overload of 3 x IPN ± 0.50 mA
• Current overload capability.
IOT Thermal drift of IO - 10°C .. + 85°C ± 0.15 ± 0.30 mA
tra Reaction time @ 10 % of IPN < 500 ns Applications
tr Response time 4) @ 90 % of IPN <1 µs
di/dt di/dt accurately followed > 100 A/µs • AC variable speed drives and servo
f Frequency bandwidth (- 3 dB) DC .. 100 kHz motor drives
• Static converters for DC motor drives
General data • Battery supplied applications
TA Ambient operating temperature - 10 .. + 85 °C • Uninterruptible Power Supplies
(UPS)
TS Ambient storage temperature - 40 .. + 90 °C
RS Secondary coil resistance @ TA = 70°C 35 Ω • Switched Mode Power Supplies
(SMPS)
TA = 85°C 37 Ω
m Mass 110 g • Power supplies for welding
applications.
Standards EN 50178 : 1997
Notes : 1) 3 mn/hour @ VC = ± 15 V, R M = 5 Ω
2)
Pollution class nr 2. With a non insulated primary bar which fills the
through-hole
3)
The result of the coercive field of the magnetic circuit
4)
With a di/dt of 100 A/µs.
060531/3

LEM Components w w [Link]

Front view Left view

Connection

Top view

Mechanical characteristics Remarks

• General tolerance ± 0.5 mm • IS is positive when IP flows in the direction of the arrow.
• Transducer fastening 2 holes ∅ 5.5 mm • Temperature of the primary conductor should not exceed
2 M5 steel screws 100°C.
Fastening torque max. 4 Nm or 2.95 Lb. - Ft. • Dynamic performances (di/dt and response time) are best
• Primary through-hole 23 x 18 mm with a single bar completely filling the primary hole.
• Connection of secondary Faston 6.3 x 0.8 mm

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice.