Scribd
Upload
166 views14 pages

Continuous Modelling

The document consists of a series of questions related to solid modeling tasks, including creating and modifying parts with specified dimensions and materials. Each question outlines the parameters, equations, and mass measurements required for the parts, which are made from different materials like 1060 Alloy, Brass, and Cast Alloy Steel. The document emphasizes the importance of using linked dimensional values and saving each part after every question.

Uploaded by

02. Akmal Adhi Pramana
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
166 views14 pages

Continuous Modelling

The document consists of a series of questions related to solid modeling tasks, including creating and modifying parts with specified dimensions and materials. Each question outlines the parameters, equations, and mass measurements required for the parts, which are made from different materials like 1060 Alloy, Brass, and Cast Alloy Steel. The document emphasizes the importance of using linked dimensional values and saving each part after every question.

Uploaded by

02. Akmal Adhi Pramana
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

- Question 4: Create the following part.

- Read following questions before modeling.

R35 R8 x 2

R14
5
R5 x 4
5

A 15 A
5
20 135°

A
5
A

B ( Radius)
C 40
20

64 20

SECTION A-A
Question 4 – Solid model 1
Unit system: MMGS (millimeter, gram, second)
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy
Density = 2700 kg/m^3
All holes through all unless shown otherwise

-Use the following parameters and equations which correspond to the dimensions labeled in the
images:

A = 50 mm
B = 10 mm
C = B + 20

(To save the most time, make use of linked dimensional values and equations.)
(Save each part after every question in a different file, so you can review your work)

-Measure the mass of the part.


What is the mass of the part (grams)?

a. 364.44

b. 345.94

c. 323.56

d. 355.22
- Question 5: Make the following changes to the part from Question 4.
- Read following questions before modeling.
- Note: Modified dimensions are indicated with inspection bubbles, new
dimensions are not.

R35
R10 x 2

R14 5 R8 x 5
10

25
B B
5 5
20 15
135°
45 A

20
3

B (Radius) 20
40
20 C

64 20

SECTION B-B
Question 5 – Solid model 1: Update parameters
Unit system: MMGS (millimeter, gram, second)
Decimal places: 2
Part origin: Arbitrary
Material: 1060 Alloy
Density = 2700 kg/m^3
All holes through all unless shown otherwise

-Use the following parameters and equations which correspond to the dimensions labeled in the
images:

A = 50 mm
B = 15 mm
C = B + 20

(To save the most time, make use of linked dimensional values and equations.)
(Save each part after every question in a different file, so you can review your work)

-Measure the mass of the part.


What is the mass of the part (grams)? _____
- Question 6: Create the part shown below.
- Note: Part is symmetrical across both the gray horizontal and vertical lines.
- Read following questions before modeling.

C (Radius)

7
A
25 7
15° R5 x 4

B 7 D

SECTION A-A

10 x 5

A A

C
Question 6 – Solid model 2
Unit system: MMGS (millimeter, gram, second)
Decimal places: 2
Part origin: Arbitrary
Material: Brass
Density = 8500 kg/m^3
All holes through all unless shown otherwise

-Use the following parameters and equations which correspond to the dimensions labeled in the
images:

A = 50 mm
B = 30 mm
C = 35 mm
D=A*4

(To save the most time, make use of linked dimensional values and equations.)
(Save each part after every question in a different file, so you can review your work)

-Measure the mass of the part.


What is the mass of the part (grams)?

a. 5010.96

b. 5112.66

c. 4996.35

d. 5180.55
- Question 7: Make the following changes t othe part in Question 6.
- Note: Part is symmetrical across both the gray horizontal and vertical lines.
- Note: Modified dimensions are indicated with inspection bubbles, new
dimensions are not.
- Read following questions before modeling.

15° R2 x 4
A

45
7

7
7
C (Radius) 7
25

B A

SECTION H-H

R5 x 15
20°
R2.50 x 15

10 x 4 E

85
C

H H
Question 7 – Solid model 2: Update parameters
Unit system: MMGS (millimeter, gram, second)
Decimal places: 2
Part origin: Arbitrary
Material: Brass
Density = 8500 kg/m^3
All holes through all unless shown otherwise

-Use the following parameters and equations which correspond to the dimensions labeled in the
images:

A = 45 mm
B = 20 mm
C = 30 mm
D=A*4
E = C - 10

(To save the most time, make use of linked dimensional values and equations.)
(Save each part after every question in a different file, so you can review your work)

-Measure the mass of the part.


What is the mass of the part (grams)? _____
- Question 12: Create the part shown below.
- Note: Part is symmetrical across the horizontal line passing through the
center bore
- Read following questions before modeling.

10

C/2

C
C/2

C
C

10 40
10 C
R2 x 2

20 45
2
5x2 D/2
45°
17.50
35 18 A
24 D D D B
17.50
45°
2
18
45

40
10 C
10

C C
40
Question 12 – Solid model 3
Unit system: MMGS (millimeter, gram, second)
Decimal places: 2
Part origin: Arbitrary
Material: Cast Alloy Steel
Density = 7300 kg/m^3
All holes through all unless shown otherwise

-Use the following parameters and equations which correspond to the dimensions labeled in the
images:

A = 40 mm
B = 120 mm
C = 20 mm
D = B/4
E = C/2

(To save the most time, make use of linked dimensional values and equations.)
(Save each part after every question in a different file, so you can review your work)

-Measure the mass of the part.


What is the mass of the part (grams)?

a. 923.18

b. 904.86

c. 955.12

d. 897.21
- Question 13: Make the following changes to the part from Question 12.
- Note: Part is symmetrical across the horizontal line passing through the
center bore
- Note: Modified dimensions are indicated with inspection bubbles, new
dimensions are not.
- Read following questions before modeling.

C/2
C/2

10

C
C

R3 x 12 C
30

3 3
3
15
3 3 3
15
R5 x 2
3 3
5x2 2 3 14
45°

17.50 18
D D B 35 24 D
17.50

45°
2 20
D/2
18

12.50 12.50
Question 13 – Solid model 3: Update Parameters
Unit system: MMGS (millimeter, gram, second)
Decimal places: 2
Part origin: Arbitrary
Material: Cast Alloy Steel
Density = 7300 kg/m^3
All holes through all unless shown otherwise

-Use the following parameters and equations which correspond to the dimensions labeled in the
images:

A = 30 mm
B = 150 mm
C = 15 mm
D = B/4
E = C/2

(To save the most time, make use of linked dimensional values and equations.)
(Save each part after every question in a different file, so you can review your work)

-Measure the mass of the part.


What is the mass of the part (grams)? _____
- Question 14: Make the following changes to the part from Question 13.
- Note: Part is symmetrical across the horizontal and vertical lines passing
through the center bore
- Note: Modified dimensions are indicated with inspection bubbles, new
dimensions are not.
- Read following questions before modeling.
10
10

C/2
C/2

C E

C C
12.50 12.50
30 R2 x 12 5
C

5 5
15

8x4
5 5
15
5
5
8.75 2 10
45°

17.50 18
D 5x2 B 35 D
18
17.50 D/2

D 30
R5 x 4 20
Question 14 – Solid model 3: Update Parameters again.
Unit system: MMGS (millimeter, gram, second)
Decimal places: 2
Part origin: Arbitrary
Material: Cast Alloy Steel
Density = 7300 kg/m^3
All holes through all unless shown otherwise

-Use the following parameters and equations which correspond to the dimensions labeled in the
images:

A = 30 mm
B = 150 mm
C = 15 mm
D = B/4
E = C/2

(To save the most time, make use of linked dimensional values and equations.)
(Save each part after every question in a different file, so you can review your work)

-Measure the mass of the part.


What is the mass of the part (grams)? _____

You might also like