SIPROTEC 5 SIPROTEC 5

Product information Product information

Disclaimer of Liability Conditions of UL Listing Current Terminals

Although we have carefully checked the contents of this publication for conformity with WARNING Servicing of the circuitry involving the batteries and replacement of the lithium batteries 2 2
Wire cross-section 2x AWG 14-10 (2.0 mm to 4.0 mm ) solid
the hardware and software described, we cannot guarantee complete conformity since Danger of death, personal injury or substantial property damage shall be done by a trained technician.
or
errors cannot be excluded.
Non-observance of the following measures can result in death, Replace battery with VARTA or Panasonic CR 2032 or BR 2032 type batteries only. 2x AWG 12-10 (2.6 mm2 to 5.2 mm2)
The information provided in this document is checked at regular intervals and any personal injury or substantial property damage. Use of another Battery may present a risk of fire or explosion. See Hardware manual stranded with UL-listed Ring Cable Lug, for
corrections that might become necessary are included in the next releases. Any for safety instructions. example, PIDG by Tyco
 The equipment must be grounded at the grounding terminal before
suggestions for improvement are welcome. Field wires of control circuits shall be separated from other circuits with respect to the Use copper conductors only, at least certified
any connections are made. This is also valid for the connections
Subject to change without prior notice. end use requirements. for a temperature of +105 °C
between base and expansion modules. The conductor cross-
Use prepared solid conductors intended for
Copyright section must be at least AWG 10 (4 mm²). The tightening torque Type 1 if mounted into a door or front cover of an enclosure.
single or multi-wiring connection, maximum 2
for the M4 grounding screw must be at least 1.2 Nm. When expanding the device with the 2nd device row, then they must be mounted
Copyright © Siemens AG 2017 – All Rights Reserved wires per pole, and for usage of ferrules,
completely inside an enclosure.
 All circuit components connected to the power supply may be crimped-on pressure wire connectors (ring-
The reproduction, transmission or use of this document or its contents is not permitted
subject to hazardous voltages. Temporarily permissible surrounding air temperature tsurr: max. 70 °C (158 °F), type and pin-type).
without express written authority. Offenders will be liable for damages. All rights,
including rights created by patent grant or registration of a utility model or design, are  Hazardous voltages may be present in equipment even after the Load conditions for the non-modular devices:
Ring Cable Lug with plastic sleeve L = 10 mm (0.39 in) to L = 12 mm (0.47 in)
supply voltage has been disconnected (capacitors can still be With surrounding air temperatures above 55 °C, no more than 50 % of the binary
reserved. Stripping length (when used without 15 mm (0.59 in); only solid copper wires may
inputs and relay outputs per assembly are allowed to be continuously active.
charged).
Registered Trademarks Ring Cable Lug) be used.
 The power-supply unit has an internal fuse which cannot be Binary input voltage DC: Urated 250 V max.
SIPROTEC®, DIGSI®, SIGUARD®, SIMEAS® and SICAM® are registered
changed. Max. rated data of the output contacts in accordance with UL certification:
trademarks of SIEMENS AG. All other product and brand names in this manual might
be trademarks, the use of which by third persons for their purposes might infringe the  Equipment with exposed current-transformer circuits must not be D (for bolt): 5.0 mm (0.20 in)
Standard Relay (Type S) DC 24 V, 5 A, General Purpose

W
D
rights of their respective owners. operated. Before disconnecting the equipment, ensure that the W: 9.5 mm (0.37 in)
DC 48 V, 0.8 A, General Purpose
current-transformer circuits are short-circuited. L: 7.1 mm (0.28 in) to 7.7 mm (0.30 in)
DC 240 V, 0.1 A, General Purpose
NOTE  The limit values stated under “Technical Data” in the SIPROTEC 5 AC 240 V, 5 A, General Purpose L
Hardware manual may not be exceeded. This must also be AC 120 V, 1/6 hp
Assembly Dimensions, Installation, Terminal and Connection Diagrams considered during testing and commissioning. AC 250 V, 1/2 hp
and Technical Data are part of the SIPROTEC 5 Hardware Manual. B300 Permissible tightening torque at the 2.7 Nm (23.9 [Link].)
If you require further information, or if particular problems occur that are not handled in R300 terminal screw
The manuals are available in the SIPROTEC Download Area on the
Internet ([Link] sufficient depth in the instructions of the respective product, you can request help
Fast Relay (Type F) AC 120 V, 5 A, General Purpose Location on device To be visible as follows:
through your local Siemens Office or representative.
AC 250 V, 5 A, General Purpose
Notes on Safety AC 250 V, 0.5 hp
This manual contains notes that must be adhered to for your own personal safety and WARNING B300
to avoid damage to property. Laser radiation! Danger of eye injury R300
However, it does not constitute a complete description of all safety measures required This device may contain a class 1 laser. High-Speed Relay with Semi- B150
for installation, service, and maintenance of the equipment (module, device) in conductor Acceleration (Type HS) Q300
question. Details are to be taken from the manuals and those are mandatory.  Do not look directly into the beam.
Power Relay (for Direct Control of DC 300 V, 4.5 A - 30 s ON, 15 min. OFF
Motor Switches) DC 250 V, 1 Hp Motor - 30 s ON,
WARNING
15 min. OFF
CAUTION DC 110 V, 3/4 Hp Motor - 30 s ON,
Danger of severe personal injury or substantial damage to
property Danger of damage due to static electrical charges 15 min. OFF
Hazardous voltages may occur in devices and modules during DC 60 V, 1/2 Hp Motor - 30 s ON,
The printed circuit boards of numerical relays contain CMOS circuits.
operation depending on the design and application. 15 min. OFF
These shall not be withdrawn or inserted under live conditions! The
DC 48 V, 1/3 Hp Motor - 30 s ON,
 Always observe the instructions given in “Qualified Electrical modules must be so handled that any possibility of damage due to
15 min. OFF
Engineering Personnel” below. static electrical charges is excluded.
DC 24 V, 1/6 Hp Motor - 30 s ON,
 During any necessary handling of individual modules the 15 min. OFF
Qualified Electrical Engineering Personnel recommendations relating to the handling of electrostatically
Only qualified electrical engineering personnel may commission and operate the endangered components (EEC) must be observed.
CAUTION
equipment (module, device) described in this document. Qualified electrical  In installed conditions, the modules are in no danger.
engineering personnel in the sense of this document are people who can demonstrate Danger of fire or chemical burn hazard
technical qualifications as electrical technicians. These persons may commission, Statement of Conformity The battery used in this device may present a fire or chemical burn
isolate, ground and label devices, systems and circuits according to the standards of Voltage Terminals, Binary Inputs and Outputs
Low-voltage Directive 2014/35/EU hazard if mistreated.
safety engineering. Wire cross-section 1x AWG 20-14 (0.5 mm2 to 2.5 mm2) solid
EMC Directive 2014/30/EU  Do not recharge, disassemble, heat above 100 °C (212 °F) or or stranded with UL-listed ferrule
Use as Prescribed incinerate.
This conformity is based on the compliance with the following Use copper conductors only, at least certified
The equipment (device, module) may only be used for such applications as set out in  Dispose the used battery promptly. for a temperature of +105 °C
the catalogs and the technical description, and only in combination with third-party harmonized standards:
equipment recommended and approved by Siemens. EN 60255-26 and EN 60255-27  Keep away from children! Ferrule with plastic sleeve L = 12 mm (0.47 in)

Problem-free and safe operation of the product depends on the following: Stripping length (when used without 12 mm (0.47 in); only copper wires may be
Other Standards ferrule) used.
• Proper transport IEEE Std C 37.90
Permissible tightening torque at the 1.0 Nm (8.85 [Link].)
• Proper storage, setup, and installation The technical data of the product is approved in accordance with UL.
For more information about the UL database, see [Link] terminal screw
• Proper operation and maintenance Select Online Certifications Directory and enter E194016 as UL File Number. Location on device To be visible as follows:

IND. CONT. EQ.

69CA

NOTE
Battery disposal
The batteries must only be replaced with the same type or another type
recommended by the manufacturer. Improper replacement involves
explosion hazard. For disposing the batteries it is necessary to observe
the local national/international directives.

SIPROTEC 5 – Product information

C53000- B5040-C001-D, Edition 08.2017 1
 SIPROTEC 5 SIPROTEC 5

Product information Product information

Dangerous Goods, Special Provision A45 of the IATA Dangerous Goods

Voltage Terminals Unpacking a Device Open Source Software
2 2
Regulations, and the ICAO Technical Instructions). This only applies to the
Wire cross-section AWG 22-12 (0.5 mm to 2.5 mm ) solid Devices are tested prior to delivery. Devices are packed on site in a way that meets original battery or genuine replacement batteries. The product contains, among other things, Open Source Software developed by third
or stranded with listed ferrule, at least certified the requirements of standard ISO 2248. parties. The Open Source Software used in the product and the license agreements
for a temperature of +105 °C Rated Values concerning this software can be found in the Readme_OSS. These Open Source
• Check the packing for external transport damage. Damaged packing may
Conductor sleeve with plastic sleeve L = 10 mm (0.39 in) The rated values shown on the name plate of the device have to be observed. Software files are protected by copyright. Your compliance with those license
indicate that the devices inside have also sustained damage.
conditions will entitle you to use the Open Source Software as foreseen in the relevant
Stripping length (when used without 10 mm (0.39 in); only copper wires may be • Unpack devices carefully; do not use force. Operating Temperature
license. In the event of conflicts between Siemens license conditions and the Open
conductor sleeve) used. Permissible temperature range for permanent operation:
• Visually check the devices to ensure that they are in perfect mechanical Source Software license conditions, the Open Source Software conditions shall prevail
Permissible tightening torque at the 0.6 Nm (5.31 [Link].) -10 °C to +55 °C (+14 °F to +131 °F) with respect to the Open Source Software portions of the software. The Open Source
condition.
terminal screw Other Environmental Conditions Software is licensed royalty-free. Insofar as the applicable Open Source Software
• Check the enclosed accessories against the delivery note to make sure that
Location on device To be visible as follows: License Conditions provide for it you can order the source code of the Open Source
everything is complete. Maximum altitude above sea level: 2000 m (6562 ft) Software from your Siemens sales contact - against payment of the shipping and
• Keep the packing in case the devices must be stored or transported elsewhere. Minimum admissible atmospheric pressure: 783.8 hPa
handling charges - for a period of at least 3 years since purchase of the Product. We
Degree of pollution: 2
• The device must be situated in the operating area for at least 2 hours before you are liable for the Product including the Open Source Software contained in it pursuant
connect it to the power supply for the first time or after the device has been in
Degree of Protection (acc. to IEC 60529) to the license conditions applicable to the Product. Any liability for the Open Source
storage. Thus, you ensure temperature equalization and avoid humidity For use in environment with degree of pollution 2. Software beyond the program flow intended for the Product is explicitly excluded.
influences and condensation. Furthermore any liability for defects resulting from modifications to the Open Source
Panel surface mounting Front IP54 Software by you or third parties is excluded. We do not provide any technical support
Panel flush mounting Front IP54 for the Product if it has been modified.
Routine-Test Report Protection against contact IP2x for current terminal (installed) When using DIGSI 5 in online mode, you are provided with the option to go to the main
You can download the routine-test report on the following Internet site using the device IP2x for voltage terminal (installed) menu Show Open source information and read and display the Readme_OSS file
serial number: containing the original license text and copyright information.
[Link] To do this, the following steps are necessary:
• Switch to online mode.
Voltage Terminals IO111
2 2 • Select the device.
Wire cross-section AWG 30-16 (0.14 mm to 1.5 mm ) solid Repacking a Device
or stranded with listed ferrule, at least certified • If you store devices after incoming inspection, pack them in suitable storage • Select online in the menu bar.
for a temperature of +105 °C packaging. • Click Show Open source information.
Conductor sleeve with plastic sleeve L = 9 mm (0.35 in) • If devices are to be transported, pack them in transport packing.
Stripping length (when used without 9 mm (0.35 in); only copper wires may be • Put the accessories supplied in the packing with the device.
NOTE
conductor sleeve) used.
To read the Readme_OSS file, a PDF viewer must be installed on the
Permissible tightening torque at the 0.22 Nm to 0.26 Nm (1.95 [Link]. to 2.30 [Link]) computer.
terminal screw Returning a Device
In order to operate SIPROTEC 5 devices, a valid DIGSI 5 license is
Location on device To be visible as follows: • Return devices to the manufacturer, stating the defect. Use the original
required.
packaging or transport packaging that meets the requirements of standard
ISO 2248.
Return damaged devices to the following address:

Siemens AG
EM DG PRO MF Rückwaren
Rohrdamm 7
13629 Berlin
Germany
• When returning the devices, make sure that they are sent with the original
current and voltage terminals or alternatively – if the wired terminals must remain
in the plant – with the locks intended for the transport.
Concerning the green single-row voltage terminals, it is not important whether
they are plugged in or not. An alternative transport lock is not necessary for
these terminals.
• Protect the optical interfaces on the communication or arc-protection modules
against pollution due to dust. For this, use, for example, the dust caps mounted
on the device in delivery state.
For further information, refer to the Hardware Manual.

Storing a Device
• Only store devices on which you have carried out an incoming inspection, thus
ensuring that the warranty remains valid. The incoming inspection is described in
the Operating manual.
• SIPROTEC devices must be stored in rooms, which are clean and dry. Devices
or associated replacement modules must be stored at a temperature of
-25 °C to +55 °C (-13 °F to 131 °F).
• The relative humidity must be at a level where condensate and ice is prevented
from forming.
• Siemens recommends that you observe a restricted storage temperature range
of +10 °C to +35 °C (50 °F to 95 °F), in order to prevent the electrolytic
capacitors used in the power supply from aging prematurely.
• If the device has been in storage for more than 2 years, connect it to an auxiliary
voltage for 1 to 2 days. This will cause the electrolytic capacitors to form on the
printed circuit board assemblies again.
• If devices are to be shipped elsewhere, you can reuse their transport packaging.
If using other packaging, ensure that the transport requirements according to
ISO 2248 are met. Storage packaging for individual devices is not adequate for
transport purposes.
• The lithium batteries contained in SIPROTEC devices meet all international
requirements of the hazardous goods specifications for the various carriers
(Special Provision 188 of the UN Recommendations on the Transport of

SIPROTEC 5 – Product information

C53000- B5040-C001-D, Edition 08.2017 2