20/9/2020 GPON – Basic Command OLT Huawei – [Link].

ZERO

[Link]

Keep Your Spirit To Learn , and Never Give up To Learn

WRITTEN BY NETWORKINGFROMZEROMARCH 31, 2017JUNE 20, 2017

GPON – Basic Command OLT Huawei

Continuing previous article about some Basic Command in OLT ZTE. Now, it’s time to share about some basic Commands at OLT
Huawei. Nowadays GPON Technologies have adopted to many brands Like Cisco , Alcatel Lucent / Nokia , Huawei , ZTE , Fiberhome ,
and etc.

I have knowledge with some brands like ZTE , Huawei , Fiberhome , and Alcatel Lucent. but mostly with ZTE and Huawei. At Least
Their Concept is all same.

That’s same like Topology Below :

There is Always OLT and ONT.

Okay , Here we go of some basic Commands At OLT Huawei.

Checking OLT Uptime

OL01#display sysuptime
System up time: 324 day 20 hour 55 minute 38 second

Checking OLT Board

[Link] 1/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
OL01#display board 0
————————————————————————-
SlotID BoardName Status SubType0 SubType1 Online/Offline
————————————————————————-
0
1 H805GPFD Normal
2 H805GPFD Normal
3 H805GPFD Normal
4 H805GPFD Normal
5 H805GPFD Normal
6 H805GPFD Normal
7 H802SCUN Active_normal –> Control Module

8 H802SCUN Standby_normal –> Control Module

9 H805GPFD Normal
10 H805GPFD Normal
11 H805GPFD Normal
12 H805GPFD Normal
13 H805GPFD Normal
14 H805GPFD Normal
15 H805GPFD Normal
16 H805GPFD Normal
17 H801X2CS Normal –> Uplink Module

18 H801X2CS Normal –> Uplink Module

19 H801PRTE Normal
20 H801PRTE Normal
————————————————————————-

OL01#

Checking OLT processor and Memory per Slot

OL01#display mem 0/1

Memory occupancy: 33%

OL01#display cpu 0/1

Send message for inquiring board cpu occupancy successfully, board executing…
CPU occupancy: 15%
OL01#

Checking OLT Temperature

OL01#display temperature 0
SlotID: 1 BoardName: H805 Temperature: 42C( 107F)
SlotID: 2 BoardName: H805 Temperature: 41C( 105F

Finding ONT by SN number

[Link] 2/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
OL01#display ont info by-sn ABCDEF
—————————————————————————–

In Huawei port 1 = port 0 at system

F/S/P : 0/1/0 (remember) this ONT Meaning that locate at slot 1 port 0 onu id 2

ONT-ID :2
Control flag : active
Run state : offline
Config state : initial
Match state : initial
DBA type : SR
ONT distance(m) :–
ONT ba ery state :–
Memory occupation :–
CPU occupation :–
Temperature :–
Authentic type : SN-auth
SN : ABCDEF (HWTC-07930A53)
Management mode : OMCI
Software work mode : normal
Isolation state : normal
ONT IP 0 address/mask : –
Description : IRONMAN
Last down cause : dying-gasp –> down caused by dying gasp (dying-gasp = ont off )

Last up time : 2016-11-11 17:52:08+07:00 –> Log Last Uptime

Last down time : 2016-11-15 09:23:27+07:00

Last dying gasp time : 2016-11-15 09:23:27+07:00
ONT online duration : –
Type C support : Not support
Interoperability-mode : Unknown

Checking ONT Status

OL01#display ont info 0 1 0 all

—————————————————————————–
F/S/P ONT SN Control Run Config Match Protect
ID flag state state state side
—————————————————————————–
0/ 1/0 1 ABCDEF deactivated offline initial initial no
0/ 1/0 2 REZABU active offline initial initial no —
0/ 1/0 4 BAREZU active online normal match no –> ONT online

Checking ONT History Logs

[Link] 3/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#display ont register-info 0 1
——————————————————————————
Index : 10
Auth-type : SN-auth
SN : ABCDEF (HWTC-19698F53)
TYPE : 245H
UpTime : 2016-11-02 16:56:37+07:00
DownTime : 2016-11-04 07:52:15+07:00
DownCause : ONT dying-gasp
——————————————————————————
Index :9
Auth-type : SN-auth
SN : ABCDEF (HWTC-19698F53)
TYPE : 245H
UpTime : 2016-10-31 22:29:05+07:00
DownTime : 2016-11-02 16:42:36+07:00
DownCause : ONT dying-gasp
——————————————————————————
Index :8
Auth-type : SN-auth
SN : ABCDEF (HWTC-19698F53)
TYPE : 245H
UpTime : 2016-10-29 00:25:35+07:00
DownTime : 2016-10-31 22:13:03+07:00
DownCause : ONT dying-gasp

checking ONT mac address

OL01#display mac-address port 0/1/0 ont 2

———————————————————————–
SRV-P BUNDLE TYPE MAC MAC TYPE F /S /P VPI VCI VLAN ID
INDEX INDEX
———————————————————————–
2389 – gpon aaaa-bbbb-cccc dynamic 0 /1 /0 2 2 122
2388 – gpon bbbb-aaaa-cccc dynamic 0 /1 /0 2 1 212
———————————————————————–
Total: 2
Note: F–Frame, S–Slot, P–Port, F/S/P indicates PW Index for PW,
A–The MAC address is learned or configured on the aggregation port,
VPI indicates ONT ID for PON, VCI indicates GEM index for GPON,
v/e–vlan/encap, pritag–priority-tagged,
ppp–pppoe, ip–ipoe, ip4–ipv4oe, ip6–ipv6oe

OL01#

Checking ONT power

[Link] 4/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#display ont optical-info 0 all
—————————————————————————–
ONT Rx power Tx power OLT Rx ONT Temperature Voltage Current
ID (dBm) (dBm) power(dBm) (C) (V) (mA)
—————————————————————————–
4 -23.10 2.30 -24.21 56 3.260 13
6 -21.08 2.28 -21.49 44 3.240 13

Checking ONT Version

OL01#display ont version 0 1 0 4

————————————————————————–
F/S/P : 0/1/0
ONT-ID :4
Vendor-ID : HWTC
ONT Version : 49
Product-ID :4
Equipment-ID : 24
Main Software Version : V3R0
Standby Software Version : V3R0
OntProductDescription : EchoLife
Support XML Version : 1.3.
OL01#

Checking ONT IP (Routing Mode)

OL01#display ont wan-info 0/1 0 4

———————————————————————
F/S/P : 0/1/0
ONT ID :4
———————————————————————
Index :1
Name : OLT_C_INTERNET_DHCP_WAN
Service type : Internet
Connection type : IP routed
IPv4 Connection status : Connected
IPv4 access type : DHCP
IPv4 address : [Link]
Subnet mask : [Link]
Default gateway : [Link]
Manage VLAN : 212
Manage priority :0
Option60 : Yes
Switch : Enable
MAC address : BBBB-AAAA-CCCC
Priority policy : Specified
L2 encap-type : IPoE
IPv4 switch : Enable
IPv6 switch : Disable
———————————————————————
OL01#

[Link] 5/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]

Checking ONT port status

OL01#config
OL01(config)#interface gpon 0/1

OL01(config-if-gpon-0/1)#display ont port state 0 4 eth-port all

————————————————————————–
ONT-ID ONT ONT Speed(Mbps) Duplex LinkState RingStatus
port-ID Port-type
————————————————————————–
4 1 GE – – down –
4 2 GE 100 full up –
4 3 GE – – down –
4 4 GE – – down –
————————————————————————–
OL01(config-if-gpon-0/1)#

Checking ONT configuration

OL01#display current-configuration ont 0/1/0 4

#
[gpon]
<gpon-0/1>
interface gpon 0/1
ont add 0 4 sn-auth “ABCDEF” omci ont-lineprofile-id 5
ont-srvprofile-id 1 desc “HULK”
ont ipconfig 0 4 dhcp vlan 212 priority
ont internet-config 0 4 ip-index 0
ont wan-config 0 4 ip-index 0 profile-id 1
ont port route 0 4 eth 1 enable –> routing mode

ont port native-vlan 0 4 eth 2 vlan 122 priority 0 –> bridging mode

ont port native-vlan 0 4 eth 3 vlan 122 priority 0 –> bridging mode

ont port route 0 4 eth 4 enable –> routing mode

#
[bbs-config]
<bbs-config>
service-port 2677 vlan 212 gpon 0/1/0 ont 4 gemport 1 multi-service user-vlan 212 tag-transform translate inbound traffic-table index 20
outbound
traffic-table index 20
service-port 2678 vlan 122 gpon 0/1/0 ont 4 gemport 2 multi-service user-vlan 122 tag-transform translate inbound traffic-table index 0
outbound traffic-table index 0
return
OL01#

Checking ONT Configuration per-Port

[Link] 6/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
OL01#display current-configuration port 0/1/1
#
[gpon]
<gpon-0/1>
interface gpon 0/1
port 1 ont-auto-find enable –> Configuring this to detect your unregister ONU automatically

Checking How many Services per-ONT

OL01#display service-port port 0/1/0 ont 4

{ <cr>|e2e<K>|gemport<K>|sort-by<K> }:

Command:
display service-port port 0/1/0 ont 4
Switch-Oriented Flow List
—————————————————————————–
INDEX VLAN VLAN PORT F/ S/ P VPI VCI FLOW FLOW RX TX STATE
ID ATTR TYPE TYPE PARA
—————————————————————————–
2677 212 common gpon 0/1 /0 4 1 vlan 212 20 20 up
2678 122 common gpon 0/1 /0 4 2 vlan 122 0 0 up
—————————————————————————–
Total : 2 (Up/Down : 2/0)
Note : F–Frame, S–Slot, P–Port,
VPI indicates ONT ID for PON, VCI indicates GEM index for GPON,

OL01#

You can Ping From Your ONT :p

OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont remote-ping 0 4 ip-address [Link]

OL01(config-if-gpon-0/1)#
—————————————–
ONT remote-ping information
—————————————–
F/S/P : 0/ 1/0
ONT-ID :4
ONT IP Index :0
IP address of ping : [Link]
Transmit packets : 4
Receive packets : 4
Lost packets :0
Lost packets ratio(%): 0
Min delay(ms) : 31
Max delay(ms) : 31
Average delay(ms) : 31
Error Code :–
—————————————–

Reboot ONT

[Link] 7/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]

OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont reset 0 4

Reset Factory ONT

OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont factory-se ing-restore 0 4

How To Release Renew ONT as DHCP client

OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont ipconfig 0 4 dhcp reset

Checking Rx Level For OLT Uplink

OL01#config
OL01(config)#interface giu 0/18
OL01(config-if-giu-0/18)#display port ddm-info 0
Temperature(C) : 38.640000
Supply voltage(V) : 3.260000
TX bias current(mA) : 38.000000
TX power(dBm) : 1.095110
RX power(dBm) : -14.659738
OL01(config-if-giu-0/18)#quit
OL01(config)#quit
OL01#

Reset Slot

OL01#config

OL01(config)#board reset 0/1

How To find ONT by Mac

[Link] 8/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
OL01#display location aaaa-bbbb-cccc
{ <cr>|fabric<K>|ont<K> }:

Command:
display location 4cf9-5dd3-1914
It will take several minutes, and console may be timeout, please use command idle-timeout to set time limit
Are you sure to query MAC address location ? (y/n)[n]:y
———————————————————————–
SRV-P BUNDLE TYPE MAC MAC TYPE F /S /P VPI VCI VLAN ID
INDEX INDEX
———————————————————————–
5493 – gpon aaaa-bbbb-cccc dynamic 0 /6 /6 50 1 203
———————————————————————–

If U want to Explore More about other, My advice is using “?” symbol.

I Hope this article can help you sometime.

AdChoices
PUBLICIDAD

READY FOR SPORT

Conoce Más
adidas - Sponsored

Advertisements Advertisements

REPORT THIS AD REPORT THIS AD

POSTED IN GPON, [Link] #GPON #HUAWEI.

[Link] 9/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]

59 thoughts on “GPON – Basic Command OLT Huawei”

1. PHAI VONE SAYS:

SEPTEMBER 19, 2017 AT 8:08 PM

Thank you very much

REPLY
2. ANDERSON ANAEL SAYS:
JANUARY 3, 2018 AT 4:56 AM

very important all command for OLT Huawei, tks a lot. Please, create article for configuration OLT Huawei MA5600T how-to

REPLY
1. NETWORKINGFROMZERO SAYS:
JANUARY 3, 2018 AT 2:08 AM

you’re welcome.. please see my other article.. how to register ont huawei..that’s how to create service

REPLY
2. NETWORKINGFROMZERO SAYS:
JANUARY 3, 2018 AT 8:02 AM
h ps://[Link]/2017/06/21/how-to-register-ont-huawei/

REPLY
3. ANDERSON ANAEL SAYS:
JANUARY 3, 2018 AT 8:20 PM

my difficulty is being configure the OLT to work with the uplink port. I’m using the GICF 0/18 0 and VLAN150 board, my difficulty
is being understand where tcon, gem, profile …. my goal is to just test in my office and leave OLT configured, tks a lot for all
information

REPLY
1. NETWORKINGFROMZERO SAYS:
JANUARY 4, 2018 AT 1:08 AM

okay please try it and just modify vlan from my article.. i hope that’s configuration will be working..if any problem.. you can
share here.. maybe i can help..

REPLY
2. ASKA SAYS:
NOVEMBER 1, 2018 AT 8:25 AM

This is Aska. Are you still looking for products of Huawei, FiberHome & ZTE 100% original and new. GEPON ONU, OLT, Fiber
CPE,WiFi module,service Board,optic accessories. you will earn more profits to stronger your business by selling our competitive
price products. Please contact me. Thx. Add my WhatsApp +8613560106987

REPLY

4. MARK SAYS:
JANUARY 9, 2018 AT 6:16 AM

Hello,
i got the script for changing traffic table
display traffic table ip from-index 0
then
service-port inbound traffice-table index outbound traffice-table index
i change it to both service-port and
the download rate changes, but the upload remain.
can you please assist me why is that?
thank you!
[Link] 10/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
REPLY
1. NETWORKINGFROMZERO SAYS:
JANUARY 9, 2018 AT 6:54 AM

can you share full configuration about traffic table and service-port inbound above?

REPLY
1. NOKIE SAYS:
JANUARY 9, 2018 AT 7:40 AM

————————————————
TD Index : 21
TD Name :
Priority : 0
Copy Priority : –
Mapping Index : –
CTAG Mapping Priority: –
CTAG Mapping Index : –
CTAG Default Priority: 0
Priority Policy : local-pri
CIR : 153600 kbps
CBS : 4917200 bytes
PIR : 512000 kbps
PBS : 682750 bytes
Fix : 0 kbps
CAR Threshold Profile: –
Color Mode : color-blind
Color Policy : dei
Referenced Status : used
————————————————

2. NETWORKINGFROMZERO SAYS:
JANUARY 9, 2018 AT 11:12 AM
maybe u can configure like this :

UAWEI#display traffic table ip index 21

————————————————
TD Index : 21
TD Name : ip-traffic-table_21
Priority : 0
Copy Priority : –
Mapping Index : –
CTAG Mapping Priority: –
CTAG Mapping Index : –
CTAG Default Priority: 0
Priority Policy : local-pri
CIR : 153600 kbps
CBS : 4917200 bytes
PIR : 153600 kbps
PBS : 4917200 bytes
Fix : 0 kbps
CAR Threshold Profile: –
Color Mode : color-blind
Color Policy : dei
Referenced Status : used
————————————————

HUAWEI#

######################################################

[Link] 11/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
HUAWEI#display traffic table ip index 22
————————————————
TD Index : 22
TD Name : ip-traffic-table_22
Priority : 0
Copy Priority : –
Mapping Index : –
CTAG Mapping Priority: –
CTAG Mapping Index : –
CTAG Default Priority: 0
Priority Policy : local-pri
CIR : 512000 kbps
CBS : 682750 bytes
PIR : 512000 kbps
PBS : 682750 bytes
Fix : 0 kbps
CAR Threshold Profile: –
Color Mode : color-blind
Color Policy : dei
Referenced Status : used
————————————————

HUAWEI#

##################

service-port xxxxx inbound traffic-table index 21 outbound traffic-table index 22

5. PRINCE SHRESTHA SAYS:

JANUARY 31, 2018 AT 5:00 AM

Can any one help me to display the optical power from all users from an OLT?

REPLY
1. NETWORKINGFROMZERO SAYS:
JANUARY 31, 2018 AT 10:12 AM

i never do it like that ,,

but this is command for looking optical power from all ont in one port olt huawei

HW01(config)#interface gpon 0/1

HW01(config-if-gpon-0/1)#display ont optical-info 0 all
—————————————————————————–
ONT Rx power Tx power OLT Rx ONT Temperature Voltage Current
ID (dBm) (dBm) power(dBm) (C) (V) (mA)
—————————————————————————–
3 -20.86 1.90 -23.02 42 3.300 16
6 -22.22 2.22 -23.38 43 3.240 13
8 -22.92 2.35 -25.09 50 3.240 17
9 -21.94 2.25 -22.45 41 3.200 12
10 -25.37 2.36 -23.47 54 3.280 12
11 -27.69 2.05 -24.82 58 3.280 15
12 -25.37 2.07 -24.32 54 3.280 14
13 -23.87 2.33 -26.39 54 3.240 14
14 -20.31 2.03 -21.94 45 3.240 14
17 -25.37 2.36 -26.39 58 3.240 17
25 -20.00 2.08 -22.22 47 3.260 12
27 -20.75 1.94 -21.37 42 3.320 14
31 -22.07 2.37 -22.84 42 3.300 13
33 -22.14 2.02 -22.76 50 3.260 12
34 -21.25 2.08 -23.38 42 3.300 13
—————————————————————————–

[Link] 12/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
REPLY

6. NOKIE SAYS:
JANUARY 31, 2018 AT 10:28 AM

Question, while you modified some adjustments via console, it is normal, it is not updating on the imanager u2000 Gui?
It is much easier to update via console/cli
How to check/modify/delete logs command by a specific ip address.
Thank you.

REPLY
1. NETWORKINGFROMZERO SAYS:
JANUARY 31, 2018 AT 10:35 AM

i just more like to update via cli.. yes it will update and nms too when we do some changes via cli… do you mean log config ??

REPLY
1. NOKIEV SAYS:
JANUARY 31, 2018 AT 10:52 AM

yes, how to check/modify/delete log config of a particular ip address?

2. NETWORKINGFROMZERO SAYS:
FEBRUARY 1, 2018 AT 10:52 AM

there only to check that log by name or index.. not in particular ip address.. that’s command is display log cli name xxxx

3. NOKIEV SAYS:
JANUARY 31, 2018 AT 10:55 AM

in regards with auto update modification via cli to gui, is there on/off switch with that? in case while doing testing?

4. NETWORKINGFROMZERO SAYS:
FEBRUARY 1, 2018 AT 10:50 AM

why do you want to stop??

7. NOKIEV SAYS:
JANUARY 31, 2018 AT 10:39 AM

another, how to check the configuration/commands of a particular ont-lineprofile profile-id.

thank you!

REPLY
1. NETWORKINGFROMZERO SAYS:
FEBRUARY 1, 2018 AT 10:53 AM

display ont-line-profile gpon all

REPLY
1. NOKIE SAYS:
FEBRUARY 1, 2018 AT 10:56 AM

“display ont-line-profile gpon all”

I would like to know te line command of the current configuration of a particular ont-lineprofile. its like the line command of a
port-ont account.

2. NETWORKINGFROMZERO SAYS:
FEBRUARY 1, 2018 AT 12:20 PM

display current-configuration ont 0/2/2 10

3. NETWORKINGFROMZERO SAYS:
FEBRUARY 1, 2018 AT 12:21 PM

that’s mean u want to see configuration ont from slot 2 port 2 onu 10
[Link] 13/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
8. NOKIE SAYS:
JANUARY 31, 2018 AT 5:27 PM

Question, while you modified some adjust via console, it is normal, it is not updating on the imanager u2000 Gui?
It is much easier to update via console/cli
How to check/modify/delete logs command by a specific ip address.
Thank you.

REPLY
9. NOKIE SAYS:
FEBRUARY 1, 2018 AT 10:54 AM

“why do you want to stop??”

To avoid confusiong while doing a testing.

how about the current configuration of ont-lineprofile, how to check it?

REPLY
1. NETWORKINGFROMZERO SAYS:
FEBRUARY 1, 2018 AT 11:15 AM

display current-configuration section global-config

REPLY
1. NOKIE SAYS:
FEBRUARY 1, 2018 AT 12:16 PM

“display current-configuration section global-config”

it worked thank you!

another question, how to check the total available/total bandwidth.

2. NETWORKINGFROMZERO SAYS:
FEBRUARY 1, 2018 AT 12:20 PM

you’re welcome ..for the olt u mean,, u can check in uplink interace

10. NOKIE SAYS:

FEBRUARY 1, 2018 AT 1:01 PM

“you’re welcome ..for the olt u mean,, u can check in uplink interace ”

what is the exact command?

thank you!

REPLY
1. NETWORKINGFROMZERO SAYS:
FEBRUARY 1, 2018 AT 2:21 PM

it depends on your uplink device from olt .. for example your uplink olt connect to cisco switch.. just show interface in cisco switch
you will see the utilization of olt.. that is an easy way if u check from olt .. tomorrow i will find a way how to check statistic
from uplink

REPLY
1. NETWORKINGFROMZERO SAYS:
FEBRUARY 15, 2018 AT 1:28 PM

Here’s the command to check statistic from uplink port

OL01-HW#config
OL01-HW(config)#interface giu 0/18
OL01-HW(config-if-giu-0/18)#display port traffic 0
The received traffic of this port(packets/s) =307216

[Link] 14/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
The received traffic of this port(octets/s) =370001834
The received traffic of this port(kbits/s) =2960014.7
The transmi ed traffic of this port(packets/s) =125081
The transmi ed traffic of this port(octets/s) =21000637
The transmi ed traffic of this port(kbits/s) =168005.1

OL01-HW(config-if-giu-0/18)#

11. NOKIE SAYS:

FEBRUARY 15, 2018 AT 1:32 PM

Here’s the command to check statistic from uplink port

OL01-HW#config
OL01-HW(config)#interface giu 0/18
OL01-HW(config-if-giu-0/18)#display port traffic 0
The received traffic of this port(packets/s) =307216
The received traffic of this port(octets/s) =370001834
The received traffic of this port(kbits/s) =2960014.7
The transmi ed traffic of this port(packets/s) =125081
The transmi ed traffic of this port(octets/s) =21000637
The transmi ed traffic of this port(kbits/s) =168005.1

OL01-HW(config-if-giu-0/18)#

On the above example, is that right, it is a 3gbps connection?

I’ll try it later.

REPLY
1. NETWORKINGFROMZERO SAYS:
FEBRUARY 15, 2018 AT 1:33 PM

yes 2,96 Gb actually

REPLY
1. NOKIE SAYS:
FEBRUARY 15, 2018 AT 1:45 PM

One more question, how about the vlan 100/0 is not connected, only vlan 10/0.

And it is fixed to a particular ip add/subnet mask?

How to do that?

2. NETWORKINGFROMZERO SAYS:
FEBRUARY 15, 2018 AT 1:50 PM

can you show me where is part the vlan 10 can connect and vlan 100 can’t connect because i’m still not understand the
question .. be er we compare the configuration between both vlan .. that’s same or not??

12. NOKIE SAYS:

FEBRUARY 15, 2018 AT 1:57 PM

can you show me where is part the vlan 10 can connect and vlan 100 can’t connect because i’m still not understand the question ..
be er we compare the configuration between both vlan .. that’s same or not??
=================================
On this page, you can query the connection and line status of the WAN port.
IPv4 Information
WAN Name Connection Status IP Acquisition Mode IP Address Subnet Mask VLAN/Priority MAC Address Connected
1_TR069_R_VID_100 Connecting DHCP — — 100/0 AlwaysOn
2_INTERNET_R_VID_10 Connected DHCP 10.x.x.x [Link] 10/0 AlwaysOn

The above is the status of the modem. Why is that? The vlan 100/0 is connecting/not connected, only the vlan 10/0.
[Link] 15/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
The ip address is fixed. 10.x.x.x [Link]

REPLY
1. NETWORKINGFROMZERO SAYS:
FEBRUARY 15, 2018 AT 2:58 PM

if u disable vlan 10 .. vlan 100 is working ??

REPLY
1. NETWORKINGFROMZERO SAYS:
FEBRUARY 16, 2018 AT 3:57 AM

i mean , try to delete vlan 10 and that service .. and see what happen for vlan 100 , is it work or not ? if work maybe we can just
activate for 1 dhcp service .. actually i am not ever set for 2 dhcp service in huawei , but in olt zte i already tried and it is work ..

13. EUGENE ANCAJAS SAYS:

FEBRUARY 15, 2018 AT 4:11 PM

hello , i have a problem with my configuration on OLT, i have the 3rd gpon card to be configured on port 1. my command wont go
through (config)#service-port 33002
looks like it maxed out of the service port.

REPLY
1. NETWORKINGFROMZERO SAYS:
FEBRUARY 15, 2018 AT 1:14 PM

can you share full information when you execute the command..

REPLY
2. NETWORKINGFROMZERO SAYS:
FEBRUARY 15, 2018 AT 1:31 PM

h ps://[Link]/2017/06/21/how-to-register-ont-huawei/
i think when you configure service above u don’t need to assign the number of service index like that (33002) just skip the
number,, because that will numbering automatically.. you just need to configure like this for example :

OL01(config)#service-port vlan 111 gpon 0/1/2 ont 100 gemport 1 multi-service user-vlan 111 tag-transform translate inbound
traffic-table index 100 outbound traffic-table index 100

REPLY
14. NOKIE SAYS:
FEBRUARY 16, 2018 AT 7:29 PM

another question, how to check if the configuration of IPTV is working? below is my current configuration.

ont-srvprofile gpon profile-id 1 profile-name “Fiber_IPTV”

ont-port eth adaptive 8
multicast-forward untag
multicast mode olt-control
port vlan eth 1 translation 10 user-vlan 10
port vlan eth 2 translation 10 user-vlan 10
port vlan eth 3 translation 10 user-vlan 10
port vlan eth 4 translation 3225 user-vlan 3225
commit

ont-lineprofile gpon profile-id 1 profile-name “Fiber_IPTV”

tcont 1 dba-profile-id 1

REPLY
1. NETWORKINGFROMZERO SAYS:
FEBRUARY 18, 2018 AT 1:04 AM

that’s configuration is defined to port configuration in ont and you need applied first in one ont,, after that because you just set the
bridging vlan..
you must check that mac-address can read at OLT from suitable VLAN, after that because that is bridging, you need to check that
[Link] 16/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
the device already go en IP address in another device outside the OLT the above topology from OLT or u can check from STB
device

REPLY
1. NOKIE SAYS:
FEBRUARY 18, 2018 AT 2:04 AM

that’s configuration is defined to port configuration in ont and you need applied first in one ont,, after that because you just set
the bridging vlan..
you must check that mac-address can read at OLT from suitable VLAN, after that because that is bridging, you need to check
that the device already go en IP address in another device outside the OLT the above topology from OLT or u can check from
STB device

Thanks, can you post a working iptv working configuration + a command or how to how to test if it is working?

Thank you!

2. NETWORKINGFROMZERO SAYS:
FEBRUARY 18, 2018 AT 2:40 AM

you’re welcome ..maybe later :p

15. SURAJ SAYS:

APRIL 19, 2018 AT 8:35 AM

How to delete SN/ont from the olt ?

REPLY
1. NETWORKINGFROMZERO SAYS:
APRIL 19, 2018 AT 9:09 AM

just delete the onu in the interface gpon,, how to do it ,, you can read my another article
h ps://[Link]/2017/06/21/how-to-register-ont-huawei/

REPLY
16. EUDOXIAFEATILAN SAYS:
NOVEMBER 3, 2018 AT 7:37 PM

can u post tutorial about how to show ssid password, or add another ssid
thnks

REPLY
1. NETWORKINGFROMZERO SAYS:
NOVEMBER 3, 2018 AT 1:33 PM

Hi eudo nice to say hi with you,, I will try to find it,, i hope i can get some useful information later

REPLY
17. MATHIAS SEMWANGA SAYS:
FEBRUARY 13, 2019 AT 1:56 AM

How do i enable the gpon port on the OLT in order to make a newly connected spli er usable

REPLY

18. FIRLYF SAYS:

JUNE 17, 2019 AT 5:32 AM

how to cnfg ONT HUAWEI hg8245h/hg8245a in OLT ZTE?

REPLY
1. NETWORKINGFROMZERO SAYS:
JUNE 17, 2019 AT 5:35 AM

I’m sorry,, i don’t have experience for that,, is it work with you?

[Link] 17/18
20/9/2020 GPON – Basic Command OLT Huawei – [Link]
REPLY
1. FIRLYF SAYS:
JUNE 18, 2019 AT 1:44 PM

yeah, sometimes is it work… but i have problem for that..the pon can’t be stable although already config to OLT..

19. MARTIN SAYS:

OCTOBER 9, 2019 AT 6:38 PM

Thansks its help ful

REPLY
20. AHMAD SAYS:
OCTOBER 9, 2019 AT 7:47 PM

hello my bro, i have already config the olt, and the ont already dialup to the olt
but question is? why internet connection cannot run in my ont?
im still confused about this configuration
feel so great if you can help me to solve this case
thank before

REPLY

21. ADHI SAYS:

DECEMBER 31, 2019 AT 7:48 PM

I have an issue. Download and upload didn’t symmetric. How to solve this issue?

REPLY
22. LUÍS ALBERTO COLOMBARI SAYS:
FEBRUARY 19, 2020 AT 8:28 PM

good morning does anyone know how to locate un by sn or serial number to be able to delete

REPLY
23. TOUOBOU MAXIME SAYS:
APRIL 14, 2020 AT 2:07 PM

please how to check the bandwith of a FSP PORT or the bandwith of an OLT UPLINK?

REPLY

[Link] 18/18