Scribd
Upload
263 views3 pages

VLSM Subnetting and Addressing Guide

The document describes a topology with routers R0, R1, and R2 connected by links. It provides instructions to complete two tables: 1) Table 1 is to be filled out with subnet descriptions, number of hosts needed, network addresses, first usable host addresses, and broadcast addresses for a 192.168.12.0/24 network. 2) A second table is for addressing the routers, switches, and hosts in a 172.31.1.0/24 network based on the guidelines provided.

Uploaded by

phoopa97
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
263 views3 pages

VLSM Subnetting and Addressing Guide

The document describes a topology with routers R0, R1, and R2 connected by links. It provides instructions to complete two tables: 1) Table 1 is to be filled out with subnet descriptions, number of hosts needed, network addresses, first usable host addresses, and broadcast addresses for a 192.168.12.0/24 network. 2) A second table is for addressing the routers, switches, and hosts in a 172.31.1.0/24 network based on the guidelines provided.

Uploaded by

phoopa97
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

In this topology (Figure. 1), you are given a 192.168.12.

0/24 network address to use to design a


VLSM addressing scheme. Based on a set of requirements, you will assign subnets and
addressing.
Complete the Subnet Table-1, listing the subnet descriptions (e.g. [[S1Name]] LAN), number of
hosts needed, then network address for the subnet, the first usable host address, and the broadcast
address. Repeat until all addresses are listed.

Figure. 1
Table 1

Number
Subnet of Host Network First Host Broadcast
Subnet Mask
Description Needed Address /CIDR Address Address

Centre LAN 50 [Link] [Link] [Link] [Link]


West LAN 20 [Link] [Link] [Link] [Link]
East LAN 10 [Link] [Link] [Link] [Link]
West Link N/A [Link] [Link] [Link] [Link]
East Link N/A [Link] [Link] [Link] [Link]
In Figure.1, subnet the [Link]/24 network based on the maximum number of hosts required
by the largest subnet by using variable length subnet masks (VLSM).

Figure.1
Complete the Addressing Table using the following guidelines:
a. Assign the first usable IP addresses to routers for each of the LAN links.
b. Use the following method to assign WAN link IP addresses:
For the WAN link between R0 and R1, assign the first usable IP address to R0 and last
usable IP address R1.
For the WAN link between R0 and R2, assign the first usable IP address to R0 and last
usable IP address R2.
c. Assign the second usable IP addresses to the switches.
d. Assign the last usable IP addresses to the hosts.
Addressing Table
Device Interface IP Address Subnet Mask Default Gateway

G0/0 [Link] [Link] N/A


R0 S0/0/0 [Link] [Link] N/A
S0/0/1 [Link] [Link] N/A
G0/0 [Link] [Link] N/A
R1
S0/0/0 [Link] [Link] N/A
G0/0 [Link] [Link] N/A
R2
S0/0/0 [Link] [Link] N/A
S0 VLAN 1 [Link] [Link] [Link]
S1 VLAN 1 [Link] [Link] [Link]
S2 VLAN 1 [Link] [Link] [Link]
L-0 NIC [Link] [Link] [Link]
L-1 NIC [Link] [Link] [Link]
L-2 NIC [Link] [Link] [Link]
In this topology (Figure 1), you are given a [Link]/17 network address to use to design a
VLSM addressing scheme. Based on a set of requirements, you will assign subnets and
addressing.
Complete the Subnet Table-1, listing the subnet descriptions (e.g. [[S1Name]] LAN), number of
hosts needed then network address for the subnet, the first usable host address, and the
broadcast
address. Repeat until all addresses are listed.

Figure 1.

Table 1

Number of Network Address First Host Broadcast


Hosts Needed /CIDR Address Address

HQ G0/0 16,000 [Link]/18 [Link] [Link]


HQ G0/1 8,000 [Link]/19 [Link] [Link]
BR1 G0/1 4,000 [Link]/20 [Link] [Link]
BR1 G0/0 2,000 [Link]/21 [Link] [Link]
BR2 G0/1 1,000 [Link]/22 [Link] [Link]
BR2 G0/0 500 [Link]/23 [Link] [Link]
HQ S0/0/0 – BR1 S0/0/0 2 [Link]/30 [Link] [Link]
HQ S0/0/1 – BR2 S0/0/1 2 [Link]/30 [Link] [Link]
BR1 S0/0/1 – BR2 S0/0/0 2 [Link]/30 [Link] [Link]

You might also like