Scribd
Upload
441 views

E2 Lab 3 5 4

Uploaded by

Ninja Nugget
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
441 views

E2 Lab 3 5 4

Uploaded by

Ninja Nugget
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

Lab 3.5.

4: Subnetting Scenario 3
Topology Diagram

Addressing Table
Device Interface Fa0/0 HQ S0/0/0 S0/0/1 Fa0/0 BRANCH1 Fa0/1 S0/0/0 S0/0/1 Fa0/0 BRANCH2 Fa0/1 S0/0/0 S0/0/1 PC1 PC2 PC3 PC4 PC5 NIC NIC NIC NIC NIC IP Address Subnet Mask Default Gateway N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 1 of 3

CCNA Exploration Routing Protocols and Concepts: Introduction to Dynamic Routing Protocols

Activity 3.5.4: Subnetting Scenario 3

Learning Objectives
Upon completion of this lab, you will be able to: Determine the number of subnets needed. Determine the number of hosts needed. Design an appropriate addressing scheme. Conduct research to find a possible solution.

Scenario
In this lab, you have been given the network address 192.168.1.0/24 to subnet and provide the IP addressing for the network shown in the Topology Diagram. The network has the following addressing requirements: The BRANCH1 LAN 1 will require 15 host IP addresses. The BRANCH1 LAN 2 will require 15 host IP addresses. The BRANCH2 LAN 1 will require 15 host IP addresses. The BRANCH2 LAN 2 will require 15 host IP addresses. The HQ LAN will require 30 host IP addresses. The link from HQ to BRANCH1 will require an IP address for each end of the link. The link from HQ to BRANCH2 will require an IP address for each end of the link. The link from HQ to BRANCH1 to BRANCH2 will require an IP address for each end of the link.

(Note: Remember that the interfaces of network devices are also host IP addresses and are included in the above addressing requirements.)

Task 1: Examine the Network Requirements.


Examine the network requirements and answer the questions below. Keep in mind that IP addresses will be needed for each of the LAN interfaces. How many subnets are needed? __________ What is the maximum number of IP addresses that are needed for a single subnet? __________ How many IP addresses are needed for each of the branch LANs? __________ What is the total number of IP addresses that are needed? __________

Task 2: Design an IP Addressing Scheme


Subnet the 192.168.1.0/24 network into the appropriate number of subnets. Can the 192.168.1.0/24 network be subnetted to fit the network requirements? __________ If the number of subnets requirement is met, what is the maximum number of hosts per subnet? __________ If the maximum number of hosts requirement is met, what is the number of subnets that will be available to use? __________

All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 2 of 3

CCNA Exploration Routing Protocols and Concepts: Introduction to Dynamic Routing Protocols

Activity 3.5.4: Subnetting Scenario 3

Task 3: Reflection
You do not have enough address space to implement an addressing scheme. Research this problem and propose a possible solution. Increasing the size of your original address space is not an acceptable solution. (Hint: We will discuss solutions to this problem in Chapter 6.)

____________________________________________________________________________ ____________________________________________________________________________ ____________________________________________________________________________


Attempt to implement your solution. Successful implementation of a solution requires that: Only the 192.168.1.0/24 address space is used. PCs and routers can ping all IP addresses.

All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 3 of 3

You might also like