Scribd
Upload
214 views

Goodmorning: 1 Wednesday, May 09, 2012

This document summarizes a student project to create an automatic night lamp with morning alarm. It includes an introduction, list of components, block diagrams, circuit diagrams, and progress updates. The project uses an LDR light sensor to automatically switch on a night lamp when it gets dark and switch it off at dawn, while also using an IC to play a morning alarm. Circuit diagrams and descriptions are provided for the power supply, LDR, NE555 timer, transistor switch, and UM66 alarm IC. The progress updates describe implementing each component on a breadboard and PCB.

Uploaded by

Tanu Newar
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
214 views

Goodmorning: 1 Wednesday, May 09, 2012

This document summarizes a student project to create an automatic night lamp with morning alarm. It includes an introduction, list of components, block diagrams, circuit diagrams, and progress updates. The project uses an LDR light sensor to automatically switch on a night lamp when it gets dark and switch it off at dawn, while also using an IC to play a morning alarm. Circuit diagrams and descriptions are provided for the power supply, LDR, NE555 timer, transistor switch, and UM66 alarm IC. The progress updates describe implementing each component on a breadboard and PCB.

Uploaded by

Tanu Newar
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 30

GOODMORNING

Wednesday, May 09, 2012 1

MINIPROJECT PROGRESS SEMINER


TOPIC: AUTOMATIC NIGHT LAMP WITH MORNING ALARM
PRESENTED BY:
TANNU NEWAR - DC2010BTE4073 SIMA MEDHI - DC2010BTE4086 RINKU BASUMATARY - DC2010BTE4072
Wednesday, May 09, 2012 2

Contents
1. 2. 3. 4. Introduction. Components required. Block diagram of the main circuit. Circuit diagram. Our progress a) Power supply Block diagram b) Circuit diagram c) Transformer d) Bridge rectifier e) Filter f) Regulator 5. LDR. 6. NE555. > Pin configuration > Block diagram > Monostable 7. Transistor as a switch. 8. UM66. 9. Working. Wednesday, May 09, 2012 10.Conclusion

INTRODUCTION
It automatically switches ON a night lamp lights when the sunlight goes below the visible regions of our eyes. This is done by a sensor called Light Dependant Resistor (LDR) which senses the light It automatically switches OFF lights whenever sunlight comes, visible to our eyes and activates a melodious morning alarm sound.

Wednesday, May 09, 2012 4

Components required:
LDR and transistor are the major components. This project uses regulated 12V power supply. IC NE555 & LM UM66 is used. some of resistors, capacitors & LED are used.

Wednesday, May 09, 2012

Block Diagram
LDR LDR

POWER SUPPLY

SWITCHING REGULATOR CIRCUIT

TRANSISTOR

SWITCH ON / OFF

MORNING ALARM
Wednesday, May 09, 2012 6

CIRCUIT DIAGRAM

Wednesday, May 09, 2012

PROGRESS

Wednesday, May 09, 2012

Power Supply
BLOCK DIAGRAM

STEP DOWN TRANFORMER

BRIDGE RECTIFIER

FILTER CIRCUIT

POWER

REGULATOR

Wednesday, May 09, 2012

POWER SUPPLY CIRCUIT

Wednesday, May 09, 2012

10

Transformer

A step down transformer is used. Contains 12 v. Connected with main AC supply. Output voltage 28.5v(p-p) ac.

Wednesday, May 09, 2012 11

Bridge rectifier

Four IN4001 diodes are used. Full wave rectifying signal is generated. Output voltage 13.5v dc

Wednesday, May 09, 2012 12

Filter circuit

A capacitor(2200F/35v) is used. A DC signal is generated. Output voltage- 13.5v

Wednesday, May 09, 2012 13

Regulator
An IC7812 is used to produce 12 v supply. It has 3 pin. Pin 1- input Pin 2- ground Pin 3- output Output voltage 11.8v

Wednesday, May 09, 2012

14

MAIN POWER SUPPLY IN BREADBOARD

Wednesday, May 09, 2012

15

MAIN POWER SUPPLY IN PCB

Wednesday, May 09, 2012

16

Light Dependent Resistor

A Light Dependent Resistor is a device which has a resistance which varies according to the amount of light falling on its surface. LDR is made of a high resistance semiconductor. LDR is a resistor whose resistor decreases with increasing light Wednesday, May 09, 2012 intensity.

17

If light falling on the device is of high enough frequency ,photons absorbed by the semiconductor give bound electrons enough energy to jump into the conduction band. The resulting free electron conduct electricity, thereby
Wednesday, May 09, 2012

18

SWITCHING REGULATOR NE555


555 is a very commonly used IC for generating accurate timing pulses. Two modes of operation: > MONOSTABLE > ASTABLE In monostable mode time delay of the pulses can be precisely controlled by an external resistor and a capacitor whereas in astable mode the frequency & duty cycle are controlled by two external resistors and a Wednesday, May 09, 2012 capacitor.

19

PIN CONFIGURATION of NE555

Wednesday, May 09, 2012

20

INTERNAL BLOCK DIAGRAM OF NE555

Wednesday, May 09, 2012

21

MONOSTABLE
A mono stable multivibrator (MMV) often called as one-shot multivibrator. It is a pulse generator circuit in which the duration of the pulse is determined by the R-C network, connected externally to the 555 timer. In such a vibrator, one state of output is stable while the other is unstable. The time taken in charging determines the pulse width.

Wednesday, May 09, 2012 22

MONOSTABLE

Wednesday, May 09, 2012

23

CIRCUIT DIAGRAM

Wednesday, May 09, 2012

24

The capacitor C has to charge through resistance RA. The larger the time constant RAC, the longer it takes for the capacitor voltage to reach +2/3VCC. In other words, the RC time constant controls the width of the output pulse. The time during which the timer output remains high is given as

tp=1.0986RAC

Derivation :
Voltage across the capacitor at any instant during charging period is given as or vc = VCC (1- e-t/RAC) since , vc = 2/3 VCC therefor 2/3VCC. = VCC. (1 e-t/RAC) or t RAC loge 3 = 1.0986 RAC So pulse width, tP = 1.0986 RAC or = 1.1 RAC
Wednesday, May 09, 2012 25

TRANSISTOR AS A SWITCH

The LDR varies according to the light falling on it. This LDR is connected as biasing resistor of the transistor. According to the light falls on the LDR, the transistor is operated in saturation and cutoff region. This transistor switches the relay to switch on/off the light.
Wednesday, May 09, 2012 26

MORNING ALARM

UM66
The UM66 series are CMOS ICs designed for using in calling bell, phone and toys. It has a built in ROM programmed for playing music. The device has very low power consumption. The melody will be available at pin1 of UM66 and here it is amplified by using transistor to drive the speaker. Resistor limits the base current of transistor within the safe values .

Wednesday, May 09, 2012 27

WORKING ON

Wednesday, May 09, 2012

28

CONCLUSION
Manual works are 100% removed. By using this system energy consumption is also reduced. In this project, no need of manual operation like ON time and OFF time setting.

Wednesday, May 09, 2012

29

THANK YOU

Wednesday, May 09, 2012

30

You might also like