Cranes

OSHA Office of Training & Education 1

Major Causes of Crane Accidents
• Contact with power lines

• Overturns

• Falls

• Mechanical failures
OSHA Office of Training & Education 2
How Do Accidents Occur?
• Instability – unsecured load, load
capacity exceeded, or ground not level
or too soft
• Lack of communication - the point of
operation is a distance from the crane
operator or not in full view of the
operator
• Lack of training
• Inadequate maintenance or inspection

OSHA Office of Training & Education 3

Who is at Risk
• Operators

• Persons at
Crane Site

OSHA Office of Training & Education 4

Types of Cranes
• Mobile
• Hydraulic
• Overhead
• Gantry
• Tower

OSHA Office of Training & Education 7

 Crane Hazards
• Improper load • Working too close to
rating power lines
• Excessive speeds • Improper exhaust
• No hand signals system
• Inadequate • Shattered windows
inspection and • No steps/guardrails
maintenance walkways
• Unguarded parts • No boom angle
• Unguarded swing indicator
radius • Not using outriggers

OSHA Office of Training & Education 8

 Planning Before Start-Up
• Level the crane and ensure support surface is firm and able to
support the load
• Contact power line owners and determine precautions. Know the
location and voltage of overhead power lines.
• Know the basic crane capacities, limitations, and job site restrictions,
such as the location of power lines, unstable soil, or high winds.
• Make other personnel aware of hoisting activities.
• Barricade areas within swing radius.
• Ensure proper maintenance and inspections.
• Determine safe areas to store materials and place machinery.

OSHA Office of Training & Education 9

 Competent Person
The competent person must
inspect all machinery and
equipment prior to each
use, and during use, to
make sure it is in safe
operating condition.

If it needs fixing, take it out

of service and don’t use it Broken
until it is fixed
Track

OSHA Office of Training & Education 10

 Load Capacity - Speed - Warnings

• Make sure the crane

operator can see the:
 Rated Load
Capacities
 Operating Speeds
 Special Hazard
Warning or
Instruction

Load Rating Chart

OSHA Office of Training & Education 11
Know the Weight of the Load
• Refer to shipping ticket or other
documentation
• Ensure lift calculations are correct
• Ensure load is within load chart rating for
boom length and load radius of crane
• Crane is rated by the maximum weight it
will lift at a minimum radius and minimum
boom length – the further from its
centerpoint, the less it will lift

OSHA Office of Training & Education 12

 Load Limiting Factors
• Not level
• Wind
• Side loads
• On its wheels
• Lifting over the side
• Use of extensions, jibs and other
attachments
• Limits of wire rope, slings and lifting devices
OSHA Office of Training & Education 13
 Load Example –
30 ton crane
• Will lift 60,000 pounds at 10 feet from the
center pin of the crane
• Based on level surface, no wind, and
outriggers fully extended
• At 25 feet from the center pin with an 80 foot
boom, the capacity is only 14,950 pounds
• At 74 feet from the center pin, the capacity
is only 4,800 pounds

OSHA Office of Training & Education 15

 Improper Load

Improper loads or speeds can result

in the tipping of the crane
OSHA Office of Training & Education 16
Improper Load

OSHA Office of Training & Education 17

Improper Load

OSHA Office of Training & Education 18

 Power Lines

Stay clear
from power
lines at least
10 feet

OSHA Office of Training & Education 19

 Hand Signals

An illustration of
the signals must
be posted at the
job site

OSHA Office of Training & Education 20

 Guard Moving Parts

Unguarded
Chain Drive

Guard moving parts such as gears or belts

OSHA Office of Training & Education 21

 Swing Radius

Stay out of the swing radius of the crane –

Make sure there are barrier guards showing swing radius
OSHA Office of Training & Education 22
 Operator Visibility

Broken Window

Make sure broken windows or other obstructions

do not prevent the operator from seeing
OSHA Office of Training & Education 23
 Ladders

Ladder

Use ladders to get to the upper portion of the cab

OSHA Office of Training & Education 24
 Guardrails

Runways and steps need to have guardrails,

handholds and slip resistant surfaces
OSHA Office of Training & Education 25
 Suspended Loads

Don’t stand under suspended loads

OSHA Office of Training & Education 26

 Boom Angle Indicator

A boom angle indicator must be on the crane

OSHA Office of Training & Education 27

 Supporting Surface

Cranes must be on a firm supporting

surface and level within 1 percent
OSHA Office of Training & Education 28
 Sheaves

The grooves must be smooth and free from surface

defects which could cause rope damage
OSHA Office of Training & Education 29
 Rigging Equipment Slings
Types of slings include alloy steel chain, wire rope,
metal mesh, natural or synthetic fiber rope, and
synthetic web.

Chain Wire rope Metal mesh Synthetic

OSHA Office of Training & Education 30

 Annual Inspections
Inspection of the
hoisting machinery
must be made by a
competent person
The employer must
maintain a record of
these inspections Crane wasn’t inspected
and tipped over

OSHA Office of Training & Education 31

 What to Inspect
• Correct air pressure and no leaks
• Tires properly inflated
• Clearance for tail swing
• Wire rope wear
• Physical damage to crane
• Loose or missing hardware, nuts, or bolts
• Fluid leaks

OSHA Office of Training & Education 32

Remove From Service

Immediately remove damaged or

defective slings from service
OSHA Office of Training & Education 33
 Damaged wire rope

Crushed Rope

Broken Strands

Damaged wire rope must be taken out of service

OSHA Office of Training & Education 34

 Worn Part

OSHA Office of Training & Education 35

 Tire Inspections

Conduct
regular
inspections
of tires for
excessive
wear or
damage

OSHA Office of Training & Education 36

 Training
• Operators:
must qualify on specific crane type
Must include on-the-job training
• Supervisor / competent person

OSHA Office of Training & Education 37

 Summary
• An unstable load, lack of communication, lack of
training, and inadequate maintenance or inspection are
major contributors to crane accidents.
• Operators or others working in the area can be
victims to “struck by" and "caught in" injuries.
• Contact with power lines causes many accidents.
• A competent person must inspect a crane regularly
to insure it is in proper order.
• Planning and training reduces accidents.

OSHA Office of Training & Education 38