UNIT – IV

Basic Processing Unit

Overview
 Instruction Set Processor (ISP)
 Central Processing Unit (CPU)

 A typical computing task consists of a series

of steps specified by a sequence of machine

instructions that constitute a program.
 An instruction is executed by carrying out a

sequence of more rudimentary operations.

Some Fundamental
Concepts
Fundamental Concepts
 Processor fetches one instruction at a time and
perform the operation specified.
 Instructions are fetched from successive memory
locations until a branch or a jump instruction is
encountered.
 Processor keeps track of the address of the memory
location containing the next instruction to be fetched
using Program Counter (PC).
 Instruction Register (IR)
Executing an Instruction
 Fetch the contents of the memory location pointed
to by the PC. The contents of this location are
loaded into the IR (fetch phase).
IR ← [[PC]]
 Assuming that the memory is byte addressable,
increment the contents of the PC by 4 (fetch phase).
PC ← [PC] + 4
 Carry out the actions specified by the instruction in
the IR (execution phase).
 Processor Organization
In t ern al p ro ces s o r
bus

Co n t ro l s i g n al s

PC

In s t ru ct i o n
Ad d res s
d eco d er an d
l i n es
MAR co n t ro l l o g i c

Memo ry
bus

MDR
Dat a
l i n es IR

Co n s t an t 4 R0

Sel ect MUX

Datapath
Ad d
A B
ALU Su b R n - 1 
co n t ro l ALU
l i n es
Carry -i n
XOR TEMP

F igure 7. 1. S ingle-bus organization of the datapath inside a processor.

Internal organization of the
processor
 ALU
 Registers for temporary storage
 Various digital circuits for executing different micro
operations.(gates, MUX,decoders,counters).
 Internal path for movement of data between ALU
and registers.
 Driver circuits for transmitting signals to external
units.
 Receiver circuits for incoming signals from external
units.
 PC:
 Keeps track of execution of a program
 Contains the memory address of the next instruction to be
fetched and executed.
MAR:
 Holds the address of the location to be accessed.
 I/P of MAR is connected to Internal bus and an O/p to external
bus.
MDR:
 Contains data to be written into or read out of the addressed
location.
 IT has 2 inputs and 2 Outputs.
 Data can be loaded into MDR either from memory bus or from
internal processor bus.
The data and address lines are connected to the internal bus via
MDR and MAR
Registers:
 The processor registers R0 to Rn-1 vary considerably from
one processor to another.
 Registers are provided for general purpose used by

programmer.
 Special purpose registers-index & stack registers.

 Registers Y,Z &TEMP are temporary registers used by

processor during the execution of some instruction.
Multiplexer:
 Select either the output of the register Y or a constant value 4

to be provided as input A of the ALU.

 Constant 4 is used by the processor to increment the contents

of PC.
ALU:
Used to perform arithmetic and logical
operation.
Data Path:
The registers, ALU and interconnecting bus are
collectively referred to as the data path.
 Internal processor
b us

Ri in

1.Register Transfers Ri

Ri out

Y in

Constant 4

Select MUX

A B
ALU

Z in

Z out

Figure 7.2. Input and output gating for the registers in Figure 7.1.
 The input and output gates for register Ri are
controlled by signals isRin and Riout .
R Is set to1 – data available on common bus
in
are loaded into Ri.
R
iout Is set to1 – the contents of register are
placed on the bus.
R
iout Is set to 0 – the bus can be used for
transferring data from other registers .
Data transfer between two
registers:
EX:
Transfer the contents of R1 to R4.
1. Enable output of register R1 by setting
R1out=1. This places the contents of R1 on
the processor bus.
2. Enable input of register R4 by setting
R4in=1. This loads the data from the
processor bus into register R4.
Architecture Riin
Internal processor
bus

Ri

Riout

Yin

Constant 4

Select MUX

A B
ALU

Zin

Z out

Figure 7.2. Input and output gating for the registers in Figure 7.1.
2.Performing an Arithmetic or
Logic Operation
 The ALU is a combinational circuit that has no
internal storage.
 ALU gets the two operands from MUX and bus.
The result is temporarily stored in register Z.
 What is the sequence of operations to add the
contents of register R1 to those of R2 and store the
result in R3?
1. R1out, Yin
2. R2out, SelectY, Add, Zin
3. Zout, R3in
Step 1: Output of the register R1 and input of
the register Y are enabled, causing the
contents of R1 to be transferred to Y.
Step 2: The multiplexer’s select signal is set to
select Y causing the multiplexer to gate the
contents of register Y to input A of the ALU.
Step 3: The contents of Z are transferred to the
destination register R3.
Register Transfers
 All operations and data transfers are controlled by the processor clock.
Bus

D Q
1
Q
Riout

Ri in
Clock

Figure 7.3.
Figure 7.3.Input
Inputand
andoutput
output gating
gating for one register
register bit.
bit.
Fetching a Word from Memory
 Address into MAR; issue Read operation; data into MDR.
Memory-bus Internal processor
data lines MDRoutE MDRout bus

MDR

MDR inE MDRin

Figure 7.4.
Figure 7.4. Connection and control
Connection and controlsignals
signalsfor
forregister
registerMDR.
MDR.
3.Fetching a Word from
Memory
 The response time of each memory access varies
(cache miss, memory-mapped I/O,…).
 To accommodate this, the processor waits until it
receives an indication that the requested operation
has been completed (Memory-Function-Completed,
MFC).
 Move (R1), R2
 MAR ← [R1]
 Start a Read operation on the memory bus
 Wait for the MFC response from the memory
 Load MDR from the memory bus
 R2 ← [MDR]
 Step 1 2 3

Timing Clock

MARin

Assume MAR Address

is always available
on the address lines
Read
of the memory bus.
MR

MDRinE
 Move (R1), R2
1. R1out, MARin, Read Data

2. MDRinE, WMFC
MFC
3. MDRout, R2in
MDR out

Figure 7.5. Timing of a memory Read operation.

4.Storing a word in memory
 Address is loaded into MAR
 Data to be written loaded into MDR.

 Write command is issued.

 Example:Move R2,(R1)

R1out,MARin
R2out,MDRin,Write
MDRoutE, WMFC
Execution of a Complete
Instruction
 Add (R3), R1
 Fetch the instruction

 Fetch the first operand (the contents of the

memory location pointed to by R3)

 Perform the addition

 Load the result into R1

 Execution of a Complete
Instruction Internal processor
bus

Add (R3), R1 Control signals

PC
Step Action
Instruction
Address
decoder and
lines
1 PC out , MAR in , Read, Select4,Add, Zin MAR control logic

Memory
2 Zout , PC in , Y in , WMF C bus

3 MDRout , IR in Data
MDR
lines IR
4 R3out , MAR in , Read
5 R1out , Y in , WMF C Y
Constant 4 R0
6 MDRout , SelectY,Add, Zin
7 Zout , R1in , End Select MUX

Add
A B
ALU Sub R n - 1 
control ALU
lines
Figure7.6. Control sequence
forexecutionof theinstructionAdd (R3),R1.
XOR
Carry-in
TEMP

Figure 7.1. Single-bus organization of the datapath inside a processor.