BUILDING CONSTRCTION- PART I

PREPARED BY

PROF. DR. LIAQAT ALI QURESHI

DEPARTMENT OF CIVIL ENGINEERING
UET TAXILA
CHAPTER 01

MASONARY
BRICK MASONRY
 When bricks are laid in mortar in a proper systematic
manner, they form a homogeneous mass, which can
withstand forces without disintegration. This mass of
the structure, so made by the use of bricks is called
"Brick Masonry" or simply "Brick work".
 Bricks are of uniform size and shape, light in weight,
durable, fire resistant, have high resale value, low
maintenance cost and are easily available in plain
areas.
 Brick Masonry is commonly used for construction of
ordinary as well as important buildings in plain areas
now-a-days.
SOME IMPORTANT TERMS USED IN BRICK MASONRY

(1) BRICK
 An artificial structural element in the form of a

rectangular block of clay is called a “Brick ". Bricks

can be manufactured of any required shape and size.
The sizes of some standard bricks are given as
follows:
SOME IMPORTANT TERMS USED IN BRICK MASONRY

 These sizes are called "Nominal, designated or

format sizes" and are used while estimating the
number of bricks in a given volume of structure.
 The actual sizes in which bricks are
manufactured, are slightly smaller to allow for the
layer of mortar present all around the brick,
usually taken as 3/8 in thick.
 The Actual or Work size of English standard
brick, which is mostly used in Pakistan, is usually
taken as 8 5/8 in 4 1/8 in x 2 5/8 in.
SOME IMPORTANT TERMS USED IN BRICK MASONRY

(2) FROG
 The depression provided in the face of a brick is called a "Frog".

 It is provided in the brick to achieve the following purposes:

(a) To form a key of mortar in between any two adjacent courses

of brick work, so as to increase the lateral strength of the
structure.

(b) To reduce the weight of the bricks, so that the bricks can be
laid with convenience.

(c) To provide a place for putting the impression of trade-mark or

the year of manufacturing of the bricks.
SOME IMPORTANT TERMS USED IN BRICK MASONRY

(3) POSITION OF BRICKS

 (a) The position of brick, when laid with its Frog
upward in the horizontal plane, is termed as
"Brick on bed".
 (b) The position of the brick when laid on its
side "9 in x 3 in", with frog in the vertical plane
is called "Brick on edge".
 (c) The position of brick when laid on its side "4
1/2 in x 3 in", with frog in the vertical plane is
called " Brick on end".
SOME IMPORTANT TERMS USED IN BRICK MASONRY

(4) COURSE
Each horizontal layer of bricks laid in mortar in a brick work is called a
"course".

(5) STRETCHER
Brick, laid with its length horizontal and parallel with the face of the
wall or other masonry member is called a "Stretcher" and a course, in
which, all the bricks are laid as Stretchers is called a “Stretching
course" or "Stretcher course".
SOME IMPORTANT TERMS USED IN BRICK MASONRY

(6) HEADER
A brick laid, so that only its end shows on the face of a
wall is called a "Header" and a course, in which all the
bricks are laid as headers, is known as "Heading
Course" or "Header course".
SOME IMPORTANT TERMS USED IN BRICK MASONRY

(7) QUOIN
The external corner of the wall is called a "Quoin".

(8) QUOIN BRICK

The brick, which forms the external corner of a wall is known
as " Quoin brick".

(9) QUOIN HEADER

A corner header, in the face of wall, which is a stretcher in
the side wall is known as "Quoin header".

(10) QUOIN STRETCHER

A corner stretcher in the face of a wall, which is header in the
side wall is known as "Quoin stretcher".
SOME IMPORTANT TERMS USED IN BRICK MASONRY

(11) BRICK BATS

 The pieces of bricks, cut long their length and having

width equivalent to that of a full or half brick are called

"Brick bats“.
 Some common Brick Bats are shown below:
 SOME IMPORTANT TERMS USED IN BRICK
MASONRY
(12) QUEEN CLOSER

 Queen closer is a brick, which is half as wide as full brick

and is made by cutting a whole brick lengthwise into two
portions.
 These are generally used next to the Quoin header for
creating bonds in brickwork.

(13) KING CLOSER

 A brick, whose one diagonal piece is cut off one corner by a

vertical plane passing through the center of one end to the

center of one side.
 It is actually 7/8 of a full brick but is usually called a 3/4 brick
SOME IMPORTANT TERMS USED IN BRICK MASONRY

(14) BEVELED CLOSER

 A brick cut longitudinally along a vertical plane, starting at the

middle of one end to the far corner.

 One quarter of the brick is cut off in this way.

(15) BULL NOSE BRICK

 A brick with rounded corners is called a “Bull Nose Brick”

(16) SQUINT BRICKS

 These bricks are used to construct acute (>90 degree) or obtuse

(< 90 degree) corners in brick masonry.

 These are special forms of bricks.
 SOME IMPORTANT TERMS USED IN BRICK MASONRY
(17) JAMB
The vertical sides of door or window openings provided in
a wall are known as "Jambs".

(18) REVEALS
The part of the Jamb opening , which is exposed between
a door or window frame and the face or back of a wall is
known as " Reveal".

(19) SILL
The horizontal part (either of timber, concrete, stone,
metal, etc) at the bottom of a door or window, supporting
the vertical members of the frame is known as " Sill " and
its height window base from the floor level is known as "
Sill level ".
SOME IMPORTANT TERMS USED IN BRICK MASONRY
(20) MORTAR
 The paste obtained by mixing a binding material and a fine
aggregate in suitable proportions in addition to water is known as
"Mortar".

 Cement and Lime are used as binding materials and Sand, Surkhi,
Cinder, etc. are used as fine aggregates.

 The mortars are named according to the type of binding material

used in their preparation such as, cement mortar, lime mortar, etc.

 The mortar prepared from simple earth is known as "Mud Mortar".

 The mortar not only acts as a cementing bed between any two
courses of bricks but also, gives strength to the structure by holding
the individual bricks together to act as a homogenous mass.
 BONDS
Bond is the arrangement of bricks or stones in each course, so as to
ensure the greatest possible interlocking and to avoid the continuity of
vertical joints in two successive courses, both on the face and in the body
of a wall.

OBJECTIVES OF BONDS

A bond is provided to achieve the following objectives:

(a) The primary objective of providing a bond is to break the continuity of the
vertical joints in the successive courses both in the length and thickness of
masonry structure. As a result, the structure will act as a bounded mass
and its load will be transmitted uniformly to the foundations.

(b) To ensure longitudinal and lateral strength of the structure.

(c) To provide pleasing appearance by laying bricks symmetrically.

(d) To do masonry work quickly by engaging more masons on a job at a time.

TYPES OF BONDS
(1) ENGLISH BOND

The bond, in which headers and stretchers are laid in

alternate courses, is called "English bond".
 TYPES OF BONDS
ENGLISH BOND
The following are the salient features of English bond:

(i) Headers and stretchers are laid in alternate courses.

(ii) In each heading course, a queen closer is placed next

to quoin header and the remaining bricks are laid as
headers.

(iii) Every alternate header in a course comes centrally

over the joint between two stretchers in the course
below, giving an approximate lap of 2 ¼ in.
TYPES OF BONDS
ENGLISH BOND
(iv) The same course will show headers or stretchers on face and back, if
the thickness of the wall is an even multiple of half bricks (e.g. 9 in, 18
in, 27 in, etc.)

(v) The same course will show headers on the face and stretchers on the
back and vice versa, if the thickness of the wall is an odd multiple of
half brick. (13 1/2 in , 22 1/2 in , etc )

(vi) The middle portion of the thicker walls consists entirely of headers.

(vii) Every transverse joint is continuous from face to face.

TYPES OF BONDS

(2) FLEMISH BOND

The bond, in which headers and stretchers are laid alternately in the same
course, is called "Flemish bond".
TYPES OF BONDS

The following are the salient features of Flemish bond:

(i) Headers and stretchers are laid alternately in the

same course.
(ii) Every header in each course lies centrally over
every stretcher of the underlying course.
(iii) In every alternate course a queen closer is placed
next to quoin header, so as to provide a lap of
approximately 2 1/4 in.
(iv) Brick bats are to be used in walls having thickness
equal to an odd multiple of half brick.
 Comparison of English Bond and Flemish bond

Sr English Bonds Flemish bond

No
.
1 This bond consists of headers and stretchers This bond consists of headers and
laid in alternative courses. stretchers laid alternatively in each
course.
2 It is strongest of all the bonds. It is less strong for walls having
thickness more than 13 ½ inches.
3 It provides rough appearance especially for It provides good appearance for all
one brick thick walls. thickness of walls.
4 There are no noticeable continuous vertical There are partly continuous vertical
joints in the structure built in this bond. joints in the structure built in this bond.
5 Much attention is not required in providing Special attention is required in providing
this bond. this bond.
6 Progress of work is more. Progress of work is less.
7 It is costly because the use of brick bats is It is economical because brick bats are
not allowed. allowed for forming this bind.
TYPES OF FLEMISH BONDS

(a) DOUBLE FLEMISH BOND

The bond in which headers and stretchers

are laid alternately in each course, both in
the face and back of the wall, is called
Double Flemish Bond.
TYPES OF FlEMISH BONDS
(b) SINGLE FLEMISH BOND

 The bond provided in a wall with Flemish bond in facing and

English bond in backing is called "Single Flemish bond" or
"Cross bond".
 This bond combines the advantages of both English and Flemish
bonds and simultaneously eliminates their disadvantages.
 This bond is recommended where costly bricks are specified for
facing in order to provide good appearance to the wall. Also, it
can be made more economical by using cheap quality of bricks
on the back of wall.
 On the other hand, it weakens the overall strength of the wall
because of maximum use of brick and existence of continuous
vertical joints. Also, it can not be provided in walls having
thickness less than 13 ½ in.
TYPES OF BONDS
(3) HEADING BOND

 The bond in which all the bricks are laid as headers in every course
of a wall is called "Heading bond".
 3/4 bats are laid as quoin bricks in the alternate courses to break
the continuity of vertical joints, which increases the transverse
strength but weakens the longitudinal strength of the wall.
 This bond is commonly used for constructing steining of wells,
footings of walls and columns, corbels, cornices, etc.
The End