Scribd
Upload
959 views

Data Communication - Multiplexing

Data Communication Chapter 8 Multiplexing introduction • Multiplexing allows several users to share a high capacity data link to maximize link utilization. • Common application of multiplexing is in long-haul communication trunks on long-haul networks are high-capacity fiber, coaxial, or microwave links . • Need for multiplexing can be justified by: -the higher the data rate, the cost per kbps is less. -most data communicating devices require modest data rate support. Multiplexing Frequen

Uploaded by

Ahmad Shdifat
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
959 views

Data Communication - Multiplexing

Data Communication Chapter 8 Multiplexing introduction • Multiplexing allows several users to share a high capacity data link to maximize link utilization. • Common application of multiplexing is in long-haul communication trunks on long-haul networks are high-capacity fiber, coaxial, or microwave links . • Need for multiplexing can be justified by: -the higher the data rate, the cost per kbps is less. -most data communicating devices require modest data rate support. Multiplexing Frequen

Uploaded by

Ahmad Shdifat
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 42

Data Communication

Chapter 8 Multiplexing

introduction
Multiplexing allows several users to share a high capacity data link to maximize link utilization. Common application of multiplexing is in long-haul communication trunks on long-haul networks are high-capacity fiber, coaxial, or microwave links . Need for multiplexing can be justified by: -the higher the data rate, the cost per kbps is less. -most data communicating devices require modest data rate support.

Multiplexing

Frequency Division Multiplexing


FDM Useful bandwidth of transmission medium exceeds required bandwidth of single channel Each signal (channel) is modulated to a different carrier frequency called subcarrier. Carrier frequencies separated so signals spectrums do not overlap (guard bands) to prevent interference. Multiplexed signal is analog which could be used as baseband signal for second modulation step.

FDM cont.
e.g. broadcast radio (AM, FM), cable TV, and long distant voiceband signals. Drawbacks of FDM: -Channel allocated even if no data to be transmitted. -crosstalk. -intermodulation noise.

Frequency Division Multiplexing Diagram

FDM System

FDM of Three Voiceband Signals

Analog Carrier Systems


AT&T (USA) Hierarchy of FDM schemes Group
12 voice channels (4kHz each) = 48kHz Range 60kHz to 108kHz

Supergroup
60 channel FDM of 5 group signals on carriers between 420kHz and 612 kHz

Mastergroup
10 supergroups

Wavelength Division Multiplexing(WDM)


Multiple beams of light at different frequencies (colors) are carried by one optical fiber A form of FDM Each color of light (wavelength) carries separate data channel 1997 Bell Labs (USA)
100 beams Each at 10 Gbps Giving 1 terabit per second (Tbps)

Commercial systems of 160 channels of 10 Gbps now available Laboratory systems (Alcatel) 256 channels at 39.8 Gbps each
10.1 Tbps Over 100km

WDM Operation
Same general architecture as other FDM Number of sources generating laser beams at different frequencies(wavelengths). Multiplexer consolidates sources for transmission over single fiber Optical amplifiers amplify all wavelengths
Typically tens of km apart

Demux separates channels at the destination Most WDM operate in the 1550nm wavelength range Was 200GHz per channel Now 50GHz per channel.

Dense Wavelength Division Multiplexing


DWDM No official or standard definition Implies more channels more closely spaced than WDM 200GHz or less per channel.

Synchronous Time Division Multiplexing


Data rate of medium exceeds data rate of digital signal (or analog signal carrying digital data) to be transmitted. Multiple digital signals interleaved in time May be at bit level or blocks of bytes or larger. Time slots preassigned to sources and fixed and thus called synchronous TDM. Time slots allocated even if no data

Synch. TDM cont.


Time slots do not have to be evenly distributed amongst sources. Sequence of slots dedicated to a given source from frame to frame is called channel. bit and byte-interleaving are used with asynchronous and synchronous sources.

Time Division Multiplexing

TDM System

TDM Link Control


No headers and trailers Data link control protocols are not needed Flow control
Data rate of multiplexed line is fixed If one channel receiver can not receive data, the others must carry on The corresponding source must be quenched This leaves that source slots empty.

Error control
Errors are detected and handled by individual channel systems

Data Link Control on TDM

Framing
No flag or SYNC characters bracketing TDM frames Must provide frame synchronizing mechanism Added-digit framing
One control bit added to each TDM frame
Looks like another channel - control channel

Identifiable bit pattern used on control channel e.g. alternating 01010101unlikely on a data channel receiver compare incoming bit patterns on each channel with sync pattern to synchronize.

Pulse Stuffing
Problem - Synchronizing data sources Clocks in different sources drift cause loss of synchronization. Data rates from different sources not related by simple rational number Solution - Pulse Stuffing
Outgoing data rate (excluding framing bits) higher than sum of incoming rates Stuff extra dummy bits or pulses into each incoming signal until its rate matches the local clock Stuffed pulses inserted at fixed locations in frame and removed at demultiplexer

TDM of Analog and Digital Sources

Digital Carrier Systems


Hierarchy of TDM USA/Canada/Japan use one system ITU-T use a similar (but different) system US system based on DS-1 format Multiplexes 24 channels Each frame has 8 bits per channel plus one framing bit 193 bits per frame

Digital Carrier Systems (2)


For voice each channel contains one word of digitized data (PCM, 8000 samples per sec)
Data rate 8000x193 = 1.544Mbps Five out of six frames have 8 bit PCM samples Sixth frame is 7 bit PCM word plus signaling bit Signaling bits form stream for each channel containing control and routing info

Same format for digital data


23 channels of data
7 bits per frame plus indicator bit for data or systems control Data rate =7*8000=56Kbps

24th channel is sync

Mixed Data
DS-1 can carry mixed voice and data signals 24 channels used No sync byte Can also interleave DS-1 channels
Ds-2 is four DS-1 giving 6.312Mbps

Subrate multiplexing (5-9.6, 10-4.8, 20-2.4 Kbps Channels)


6*8000=48 Kbps

DS-1 Transmission Format

SONET/SDH
Synchronous Optical Network (ANSI) Synchronous Digital Hierarchy (ITU-T) Compatible Signal Hierarchy
Synchronous Transport Signal level 1 (STS-1) or Optical Carrier level 1 (OC-1) 51.84Mbps Carry DS-3 or group of lower rate signals (DS1 DS1C DS2) plus ITU-T rates (e.g. 2.048Mbps) Multiple STS-1 combined into STS-N signal ITU-T lowest rate is 155.52Mbps (STM-1)

SONET Frame Format

SONET STS-1 Overhead Octets

Statistical TDM
In Synchronous TDM many slots are wasted Statistical TDM allocates time slots dynamically based on demand Multiplexer scans input lines and collects data until frame full Data rate on line lower than aggregate rates of input lines

Statistical TDM Frame Formats

Performance
Output data rate less than aggregate input rates May cause problems during peak periods
Buffer inputs Keep buffer size to minimum to reduce delay

Buffer Size and Delay

Cable Modem Outline


Two channels from cable TV provider dedicated to data transfer
One in each direction

Each channel shared by number of subscribers


Scheme needed to allocate capacity Statistical TDM

Cable Modem Operation


Downstream
Cable scheduler delivers data in small packets If more than one subscriber active, each gets fraction of downstream capacity
May get 500kbps to 1.5Mbps

Also used to allocate upstream time slots to subscribers

Upstream
User requests timeslots on shared upstream channel
Dedicated slots for this

Headend scheduler sends back assignment of future time slots to subscriber

Cable Modem Scheme

Asymmetrical Digital Subscriber Line


ADSL Link between subscriber and network
Local loop

Uses currently installed twisted pair cable


Can carry broader spectrum 1 MHz or more

ADSL Design
Asymmetric
Greater capacity downstream than upstream Perfect fit to internet requirement

Frequency division multiplexing


Lowest 25kHz for voice
Plain old telephone service (POTS)

Use echo cancellation or FDM to give two bands Use FDM within bands

Range 5.5km

ADSL Channel Configuration

Discrete Multitone
DMT Multiple carrier signals at different frequencies Some bits on each channel 4kHz subchannels Send test signal and use subchannels with better signal to noise ratio 256 downstream subchannels at 4kHz (60kbps)
15.36MHz Impairments bring this down to 1.5Mbps to 9Mbps

DTM Bits Per Channel Allocation

DMT Transmitter

xDSL
High data rate DSL Single line DSL Very high data rate DSL See Table 8.8

You might also like