Scribd
Upload
15 views

Step-by-Step Guide to Creating an ESP32 LED Web Server

Learn to build your own ESP32 LED web server! Control LED lights remotely using Wi-Fi with this step-by-step tutorial. https://circuitdigest.com/microcontroller-projects/building-diy-led-webserver-with-esp32 https://youtu.be/zfXQkv9GbYI

Uploaded by

SemiconMedia - Circuit Digest
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
15 views

Step-by-Step Guide to Creating an ESP32 LED Web Server

Learn to build your own ESP32 LED web server! Control LED lights remotely using Wi-Fi with this step-by-step tutorial. https://circuitdigest.com/microcontroller-projects/building-diy-led-webserver-with-esp32 https://youtu.be/zfXQkv9GbYI

Uploaded by

SemiconMedia - Circuit Digest
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 7

ESP32 LED WEBSERVER:

STEP-BY-STEP TUTORIAL

Source: Circuitdigest
WHAT IS AN ESP32 WEB SERVER?
An ESP32 Web Server is a device that
responds to web requests and serves web
pages, similar to a traditional computer-
based web server. However, instead of
using a computer, the ESP32
microcontroller, equipped with built-in
WiFi capabilities, handles these tasks. It can
both respond to requests and host small web
pages, either programmed directly into its
code or stored in its flash storage or an SD
card.

Source: Circuitdigest
MATERIALS NEEDED FOR ESP32
LED CONTROL WEBSERVER
To build this project, you'll need:

o ESP32 Development Board: Controls


LED lights via the web server.
o LED Lights: Any type can be used; we've
used 2x 5mm LEDs.
o Breadboard: Connects LEDs to the
ESP32 microcontroller.
o Jumper Wires: Links the breadboard,
ESP32, and LED lights.
o USB Cable: Connects the ESP32 to your
computer for programming.
o Computer: Required for programming
and uploading code.
o Resistor: Prevents LED burnout by
limiting current flow.

Source: Circuitdigest
ESP32 LED WEBSERVER CIRCUIT
To connect LED lights to the ESP32:
1.Attach a 220-ohm resistor to GPIO
pin 12.
1. Connect the other end of the
resistor to the positive leg of
one LED.
2. Link the negative leg of the
LED to the ESP32's ground
(GND).
2.Repeat the process for GPIO pin 14
and the second LED.
For Ethernet webserver usage,
include an Ethernet shield for the
ESP32 board and make slight
adjustments to the code.

Source: Circuitdigest
ADDING THE ESP32 BOARD TO THE
ARDUINO IDE
The Arduino IDE offers a user-friendly platform
for programming ESP32 boards, catering to both
beginners and advanced users. No additional
libraries are required for using the web server, as
it's integrated into the ESP32 Arduino core.

Connecting to the ESP32 Webserver and


testing it
1.Open the same network through a device or use
the same device to whose hotspot your ESP32 is
connected
2.Open a web browser on your computer or
mobile device and enter the IP address of the
ESP32 board into the address bar.

Source: Circuitdigest
WORKING OF ESP32 LED
WEBSERVER

The project works by creating a web server on the ESP32 microcontroller that serves a
web page to a client device, such as a computer or mobile phone, over Wi-Fi. The web
page contains controls that allow you to turn the LED lights on or off.

Source: Circuitdigest
THANK YOU!!

Full Tutorial: https://youtu.be/zfXQkv9GbYI

https://circuitdigest.com/microcontroller-projects/building-diy-led-webserver-with-
esp32

Source: Circuitdigest

You might also like