www.huawei.

com

GSM Expert for Network Parameter Optimization Report

(Ethio Telecom(ET) Project)
HUAWEI TECHNOLOGIES CO., LTD.
Contents

Analysis Result

Expert for Network Parameter Optimization Solution

Basic Network Information——BSC
BSC Name BSC Version Number Number of Frequency Number of Abis A interface
of sites cells carriers transmission transmission
mode mode
131197.BSC_01. V100R017ENGC 276 GSM900: 822 900M(63-111, 9.8M); GSM900: 3653 IP IP
HW.PIAZZA.DES 10SPC575 DCS1800: 1800M(780-863, 16.8M); DCS1800: 2083
SIE.NER 279

CS/PS Traffic(Erl)

AR9311-PS Traffic(Erl) K3014-CS Traffic(Erl)

5 30000
4.5
4 25000
3.5 20000
3
2.5 15000
2
1.5 10000
1 5000
0.5
0 0
0 0 00 00 0 0 00 00 0 0 00 00 0 0 00 0 0 00 00 00 00 00 0 0 00 00 0 0 0 0 0 0 0 0 00 00 0 0 00 00 0 0 00 00 0 0 0 0 00 00
0 0: 00 : 0 0 : 0 0: 0 0: 0 0: 0 0: 0 0: 0 0: 0 0: 00: 0 0: 0 0: 00 : 0 0: 0 0: 0 0: 0 0: 00 : 0 0: 0 0: 0 0: 00: 0 0: 0 0: 00 : 0 0: 0 0: 0 0 : 0 0 : 0 0: 0 0: 0 0: 0 0: 0 0: 0 0:
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
00 02 04 06 08 10 12 14 16 18 20 22 00 02 04 06 08 10 12 14 16 18 20 22 00 02 04 06 08 10 12 14 16 18 20 22
7 7 7 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 8 8 8 9 9 9 9 9 9 9 9 9 9 9 9
2 - 0 2 - 0 2 - 0 2- 0 2- 0 2- 0 2- 0 2- 0 2- 0 2- 0 2 - 0 2- 0 2 - 0 2 - 0 2- 0 2 - 0 2- 0 2- 0 2 - 0 2- 0 2- 0 2- 0 2 - 0 2- 0 2 - 0 2 - 0 2- 0 2 - 0 2 - 0 2 - 0 2 - 0 2- 0 2- 0 2- 0 2- 0 2- 0
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 9- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19-
20 20 20 20 2 0 2 0 2 0 20 20 2 0 20 20 20 20 20 2 0 2 0 2 0 20 20 2 0 2 0 20 20 20 20 20 2 0 20 20 20 2 0 2 0 2 0 20 20
 KPI Overview
Call Drop Rate (TCH drop rate) Access Success Rate (CSSR)
Handover Success Rate (HOSR)
Call Drop Rate (TCH drop rate) Standard line

1.20% Access Success Rate (CSSR) Handover Success Rate (HOSR) Standard line
1.00%
102.00%
0.80% 98.00%
0.60% 94.00%
0.40% 90.00%
0.20% 86.00%
0.00% 82.00%
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 :0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0 :0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0
:0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0
0 0 04 0 8 12 16 20 00 04 08 12 16 20 0 0 04 0 8 12 16 20 0 0 04 0 8 12 16 20 00 04 08 12 16 20 0 0 04 0 8 12 16 20
7 7 7 7 7 7 8 8 8 8 8 8 9 9 9 9 9 9 7 7 7 7 7 7 8 8 8 8 8 8 9 9 9 9 9 9
2 - 0 2- 0 2 - 0 2 - 0 2- 0 2 - 0 2- 0 2 - 0 2 - 0 2- 0 2 - 0 2 - 0 2 - 0 2 - 0 2 - 0 2- 0 2 - 0 2- 0 2 - 0 2- 0 2 - 0 2 - 0 2- 0 2 - 0 2- 0 2 - 0 2 - 0 2- 0 2 - 0 2 - 0 2 - 0 2 - 0 2 - 0 2- 0 2 - 0 2- 0
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 9 - 19 - 1 9 - 19 - 19 - 19 - 19 - 19 - 1 9 - 19 - 19 - 19 - 19 - 19 - 19 - 19 - 19 - 1 9 - 1 9 - 19 - 1 9 - 19 - 19 - 19 - 19 - 19 - 1 9 - 19 - 19 - 19 - 19 - 19 - 19 - 19 - 19 - 1 9 -
20 20 20 2 0 20 2 0 20 2 0 20 20 20 20 20 20 20 2 0 20 2 0 20 20 20 2 0 20 2 0 20 2 0 20 20 20 20 20 20 20 2 0 20 2 0

Uplink HQI (0-4)

Downlink HQI (0-4)
Uplink HQI (0-4) Downlink HQI (0-4) Standard line
Call Drop Rate (TCH drop rate) is better than
100.00%
96.00%
the benchmark value.
92.00% Access Success Rate (CSSR) is less than the
88.00% benchmark value.
84.00%
Handover Success Rate (HOSR) is less than
0 0 0 0 0 0 00 0 0 00 00 00 00 00 00 00 00 00 00 00 00 00 the benchmark value.
0 0: 0 0: 0 0: 0 0: 0 0 : 0 0: 0 0 : 0 0: 0 0 : 0 0: 0 0 : 0 0: 0 0 : 0 0: 0 0: 0 0: 0 0: 0 0:
: : : : : : : : : : : : : : : : : :
0 0 04 0 8 12 16 20 00 04 08 12 16 20 0 0 04 0 8 12 16 20 Uplink HQI (0-4) is more than the benchmark
7 7 7 7 7 7 8 8 8 8 8 8 9 9 9 9 9 9
2 - 0 2- 0 2 - 0 2 - 0 2- 0 2 - 0 2- 0 2 - 0 2 - 0 2- 0 2 - 0 2 - 0 2 - 0 2 - 0 2 - 0 2- 0 2 - 0 2- 0 value.
- 1 -1 - 1 -1 -1 -1 -1 - 1 - 1 -1 - 1 -1 - 1 -1 - 1 - 1 - 1 - 1
0 1 9 0 19 01 9 0 19 0 19 0 19 0 19 019 01 9 0 19 0 19 0 19 0 19 0 19 0 19 019 0 19 01 9 Downlink HQI (0-4) is less than the
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
benchmark value.
 Comprehensive Analysis-Alarm
• All active alarms

ENO alarm missing data

• Historical alarms (last three days)

GSM_ENO_AlarmCheck.xls not exist
Comprehensive Analysis-RF Channel Check

Board SndRcvMode Error may exist in 0 cells.

Number of Cells with Channel Type
Cable Connect Cross may exist in 0 cells.
2.5
Cable Connect Fault may exist in 2 cells.

2
2

1.5

0.5

0 0
0
Board SndRcvMode Er- Cable Connect Cross Cable Connect Fault
ror
 Call Drop Analysis-KPI
Call Drop Cause(%)
Radio Drop Rate of TCH
Radio Drop Rate of TCH(%)

0.6
0.5 M3030K:Call Drops on TCH M3030B:Call Drops on TCH
0.4 Ratio(Other) Ratio(Uplink Received Level)
0.3 M3030D:Call Drops on TCH M3030I:Call Drops on TCH
4.01 1.71 0.14 Ratio(Uplink and Downlink Ratio(Downlink Quality)
0.2
0.1 8.08 37.9 Received Level)

0 11.0 2 M3030H:Call Drops on TCH M3030J:Call Drops on TCH

Ratio(Uplink Quality) Ratio(Uplink and Downlink
1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Quality)
0 :0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 0:0 M3030C:Call Drops on TCH M3030A:Call Drops on TCH
:0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 :0 12.6
00 03 06 09 12 15 18 21 00 03 06 09 12 15 18 21 00 03 06 09 12 15 18 21
Ratio(Downlink Received Ratio(TA)
5 Level)
7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 9 9 9 9 9 9 9 9 24.48
2 - 0 2 - 0 2 - 0 2 - 0 2 - 0 2 - 0 2 - 0 2 - 0 2- 0 2 - 0 2- 0 2 - 0 2- 0 2 - 0 2 - 0 2 - 0 2 - 0 2 - 0 2 - 0 2- 0 2 - 0 2- 0 2 - 0 2 - 0
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 9 - 19 - 19 - 1 9 - 1 9 - 1 9 - 19 - 19 - 19 - 19 - 19 - 19 - 1 9 - 19 - 19 - 19 - 19 - 19 - 19 - 19 - 19 - 1 9 - 19 - 19 -
20 2 0 20 20 20 20 20 20 20 20 2 0 20 20 20 20 20 20 20 20 2 0 20 20 20 20
Number of call drops on each subcounter(Erl)
1 2 0 0 0 0111566
100 000
80000
60000
40000 28508
4473
1549
1536876 592 454 92 51 14 9 7
The call drop is mainly caused by :
20000
0

(1) M3030K:Call Drops on TCH Ratio(Other)

(2) M3030B:Call Drops on TCH Ratio(Uplink Received
Level). The call drop rate is high.
The call drop counter mainly includes :
(1) Call Drops due to CONN FAIL Received on TCHH
(Traffic Channel) in Stable State (Radio Link Failure)
(2) Number of Unsuccessful Outgoing Internal Inter-
Cell Handovers (Timer Expired) (TCHH) (Traffic
Channel). The call drop rate is high.
Call Drop Analysis-Parameter Check
PARA MO PARA ID PARA NAME network setting advise adjust reason License

SET GCELLCCCH FMSMAXOPCC MS_TXPWR_MAX_CCH 0(3)(900M),5(819) 5(900)0(1800) MS get the best the initial
(900M),5(9)(1800M),0(270) access power
(1800M)

SET GCELLBASICPARA FRDLDTX FR Use Downlink DTX YES(927),NO(174) YES reduce downlink
interference

SET GCELLBASICPARA HRDLDTX HR Use Downlink DTX YES(927),NO(174) YES reduce downlink
interference

SET GCELLBASICPARA MiccSwitch MICC Switch OFF(1101) ON decrease the uplink

interference

SET PSDTX PS DTX ENHANCEDDTX(927),OFF(1 ENHANCEDDTX reduce the PS to CS

GCELLPRIVATEOPTPARA 74) influence

SET GCELLPWR3 AMRCALLPCALLOWED Allow III Power Control For ON(437),OFF(664) ON enable AMR power
AMR control ,reduce intra-
network interference.

SET GCELLCCBASIC SATIMEROPTSW SA Multiframe Counter OFF(1101) ON SACCH frame decode timer
Optimization Switch begin from BSC receive EST
INDICATION message.

SET GCELLPSPWPARA SUPPSDLPC DL EGPRS Closed-Loop NO(1101) YES reduce the PS to CS

Power Control Support influence

SET GCELLBASICPARA HRULDTX HR Uplink DTX Shall_NOT_Use(174),Shall_U Shall_Use reduce uplink interference
se(927)

SET GCELLBASICPARA FRULDTX FR Uplink DTX Shall_NOT_Use(174),Shall_U Shall_Use reduce uplink interference
se(927)

SET GCELLCCBASIC REPEATSASET Repeated SACCH NO(1101) YES improve decode the
SACCH sucessful rate

SET GCELLPSPWPARA SUPGPRSDLPC DL GPRS Closed-Loop NO(1101) YES reduce the PS to CS

Power Control Support influence

SET GCELLPSPWPARA DLPCINITPR P0 DB0(1101) DB2 reduce the PS to CS

influence

SET GCELLCCTMR N200PARASWITCH Use LAPDm N200 ON(1059),OFF(42) ON reduce the timer unproper
 Call Drop Analysis-RxLev RxQual Distribution
uplink level <= -90dBm is 71.6%, and the uplink coverage is Weak Coverage (threshold 50%).
80]. quality [6/7]= 0.0%, uplink The interference is normal. (threshold 1%).
l <= -90dBm ratio is 41.56%, and the downlink coverage is Weak Coverage (threshold 40%).
= -80]. quality [6/7]= 0.68%, downlink The interference is normal. (threshold 1%).

Uplink HQI Downlink HQI

800000 700000

700000 600000

600000
500000
500000
400000
400000 RxLev RxLev
300000
300000
200000
200000 7 (>-70) 7 (>-70)
6 (-75~-70) 6 (-75~-70)
100000 100000
5 (-80~-75) 5 (-80~-75)
4 (-85~-80) 4 (-85~-80)
0 3 (-90~-85) 0 3 (-90~-85)
Quality Quality 2 (-95~-90) Quality Quality 2 (-95~-90)
level 0 level 1 Quality Quality 1 (-100~-95) level 0 level 1 Quality Quality 1 (-100~-95)
level 2 level 3 Quality Quality 0 (<-100) level 2 level 3 Quality Quality 0 (<-100)
level 4 level 5 Quality Quality level 4 level 5 Quality Quality
level 6 level 7 level 6 level 7
Call Drop Analysis-GCHR (MR ）

• Output the proportion of call drops in various scenarios in the GCHR.

GCHR missing data

Call Drop Analysis-Summary of Optimization Measures
• Optimization Measures (For details, see the attachment.)
Call Drop
Before the optimization measures are implemented, strictly follow the three approvals and submit the RFC. Optimization Measure Summary.xl

PARAMETER PARAMETERNAME CURRENT VALUE AJUST VALUE

TCHBUSYTHRES TCH Traffic Busy Threshold TCHBUSYTHRES(1) TCHBUSYTHRES(0)

RXMIN Minum Access RXLEV RXMIN(8) RXMIN(10)

RACHACCLEV CS RACH Min. Access Level RACHACCLEV(-109) RACHACCLEV(-106)

INTELEVHOHYST Adjacent Cell Inter-layer HO Hysteresis INTELEVHOHYST(67) INTELEVHOHYST(57)

HOTHRES Inter-layer HO Threshold HOTHRES(30) HOTHRES(33)

INTERCELLHYST,PBGTMARGIN Inter-cell HO Hysteresis,PBGT HO Threshold INTERCELLHYST(68),PBGTMARGIN(68) INTERCELLHYST(66),PBGTMARGIN(66)

ULQUALIMITAMRHR,DLQUALIMITAMRHR,ULQUALI UL Qual. Limit for AMR HR,DL Qual. Limit for AMR ULQUALIMITAMRHR(55),DLQUALIMITAMRHR(55),U ULQUALIMITAMRHR(40),DLQUALIMITAMRHR(40),U
MITAMRFR,DLQUALIMITAMRFR HR,UL Qual. Limit for AMR FR,DL Qual. Limit for LQUALIMITAMRFR(55),DLQUALIMITAMRFR(55) LQUALIMITAMRFR(40),DLQUALIMITAMRFR(40)
AMR FR
ULQUALIMIT,DLQUALIMIT UL Qual. Threshold,DL Qual. Threshold ULQUALIMIT(55),DLQUALIMIT(55) ULQUALIMIT(40),DLQUALIMIT(40)

CRO Cell Reselect Offset CRO(5) CRO(3)

INTERCELLHYST Inter-cell HO Hysteresis INTERCELLHYST(68) INTERCELLHYST(66)

DLEDGETHRES Edge HO DL RX_LEV Threshold DLEDGETHRES(25) DLEDGETHRES(28)

DLEDGETHRES,ULEDGETHRES Edge HO DL RX_LEV Threshold,Edge HO UL RX_LEV DLEDGETHRES(20),ULEDGETHRES(10) DLEDGETHRES(23),ULEDGETHRES(12)

Threshold
CALLRESTABDIS Call Reestablishment Forbidden CALLRESTABDIS(YES) CALLRESTABDIS(NO)

INTRACELLHOTIMER,OUTBSCHOCLEARTIMER,INTR T3103C,T8,T3103A INTRACELLHOTIMER(10000),OUTBSCHOCLEARTIME INTRACELLHOTIMER(25000),OUTBSCHOCLEARTIME

ABSCHOTIMER R(10000),INTRABSCHOTIMER(10000) R(25000),INTRABSCHOTIMER(25000)
MINOFFSET Min Access Level Offset MINOFFSET(0) MINOFFSET(5)
 Handover Analysis-KPI

handover is mainly Incoming External Inter-Cell Handovers The handover is poor.

handover is mainly caused by Outgoing External Inter-Cell Handovers handover difference.

Handover Analysis-KPI
Intra-Cell Handover Success Rate(%) Inter-BSC Incoming Handover Success Rate(%) Incoming Internal Handover Success Rate(%)
Overall Handover Success Rate(%) Outgoing Handover Success Rate of BSC(%) Inter-BSC Outgoing Handover Success Rate(%)
110
100
90
80
70
60
50
40
30
20
10
0
0 0 00 00 00 00 00 0 0 00 00 00 0 0 00 00 00 00 0 0 0 0 00 00 00 0 0 0 0 00 00 0 0 0 0 00 0 0 00 00 0 0 0 0 00 00 0 0 00
0 0: 0 0: 0 0: 0 0: 0 0: 0 0 : 0 0: 0 0: 00 : 0 0 : 0 0: 0 0: 0 0: 0 0: 00: 0 0: 0 0: 0 0: 0 0: 0 0 : 00: 0 0: 0 0: 00 : 0 0: 0 0: 0 0: 0 0: 0 0: 00 : 0 0: 0 0: 0 0: 0 0: 0 0: 0 0:
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
00 02 04 06 08 10 12 14 16 18 20 22 00 02 04 06 08 10 12 14 16 18 20 22 00 02 04 06 08 10 12 14 16 18 20 22
0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9
1 2- 1 2- 12 - 1 2- 1 2- 12 - 1 2- 1 2- 12 - 1 2 - 1 2- 1 2 - 1 2- 1 2- 12 - 1 2- 1 2- 1 2- 1 2- 1 2 - 12 - 1 2- 1 2- 1 2 - 1 2- 1 2- 1 2- 1 2- 1 2- 1 2 - 1 2- 1 2- 1 2- 12 - 1 2- 1 2-
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0 19 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
 Handover Analysis-Intra-BSC Handover
Inter-BSC Handover Failure Category
Number of Outgoing Internal Handover Times
Commands, Requests, Successes, and H312Dp:Number of Failed H312A:Number of Failed H312Dc:Number of Failed H312Dq:Number of Failed H312Dd:Number of Failed The intra-BSC outgoing cell handover is
Outgoing Internal Inter-Cell Outgoing Internal Inter-Cell Outgoing Internal Inter-Cell Outgoing Internal Inter-Cell Outgoing Internal Inter-Cell
Failures Handovers(Protocol Error Un- Handovers (No Channel Handovers(Abnormal Release, Handovers(Other Causes) Handovers(Abnormal Release, mainly caused by :
specified) Available) Timer Expired) No Activity on the Radio Path)
CH310:Number of Outgoing Internal 236217H312Da:Number of Failed CH312C:Number of Unsuc- H312Dh:Number of Failed H312B:Number of Failed H4100J:Codec Change Re-
(1) H312Dp:Number of Failed Outgoing
Inter-Cell Handover Requests 75 Outgoing Internal Inter-Cell
Handovers(Abnormal Release,
cessful Outgoing Internal In-
ter-Cell Handovers (Timer
Outgoing Internal Inter-Cell
Handovers(Frequency Un-
Outgoing Internal Inter-Cell
Handovers (Terrestrial Re-
jected by the MSC(Other
Causes)
Internal Inter-Cell Handovers(Protocol Error
CH313:Number of Successful Outgoing 229320Unspecified) Expired) available) source Request Failed) Unspecified)
Internal Inter-Cell Handovers" 55 H4100F:Codec Change Re-
jected by the MSC(Requested
H312Df:Number of Failed
Outgoing Internal Inter-Cell
H312G:Number of Failed
Outgoing Internal Inter-Cell
H312I:Number of Unsuccess-
ful Outgoing Internal Inter-
H4100KNumber of Failed In-
tra-BSC Handovers with (2) H312A:Number of Failed Outgoing
CH312:Number of Unsuccessful Outgoing
A-Interface Type Not Sup-
689720ported)
Handovers(Handover Failed,
Timing Advance out of
Handovers (A Interface
Failure)
Cell Handovers (Channel Ac-
tivation Failed)
Codec Change (MSC Timeout)
Internal Inter-Cell Handovers (No Channel
Internal Inter-Cell Handovers Range) Available)
CH311:Number of Outgoing Internal 235133 failure.
Inter-Cell Handover Commands 28

Number of intra-BSC incoming handover Times Incoming Internal Handover Failure Category
requests, successes, detection, responses,
and failures
H322D:Number of Unsuccess- H3229A:Number of Unsuc-
The intra-BSC incoming cell handover is
CH320:Number of Incoming Internal 236217 ful Incoming Internal Inter- cessful Incoming Internal In- mainly caused by :
Inter-Cell Handover Requests 91 Cell Handovers (Reconnection ter-Cell Handovers (No
10 28794 3599 420 235 to Old Channels Canceled) Channel Available) (TCH) (1) H322D:Number of Unsuccessful
CH323:Number of Successful Incoming 22932045 CH322C:Number of Unsuc- H322B:Number of Unsuccess-
Internal Inter-Cell Handovers 69 64 cessful Incoming Internal In- ful Incoming Internal Inter- Incoming Internal Inter-Cell Handovers
CH324:Number of Incoming Internal 230840
ter-Cell Handovers (Timer
Expired)
Cell Handovers (Terrestrial
Resource Request Failed) (Reconnection to Old Channels Canceled)
55211 H322G:Number of Unsuccess- H322I:Failed Incoming In- (2) H3229A:Number of Unsuccessful
Inter-Cell Handover Detection Messages 22 0 ful Incoming Internal Inter- ternal Inter-Cell Handovers
Received by BSC Cell Handovers (Failure on A (Channel Activation Failed) Incoming Internal Inter-Cell Handovers (No
Interface)
CH321:Number of Incoming Internal 235133 Channel Available) (TCH)
Inter-Cell Handover Responses 44 failure.
CH322:Number of Unsuccessful Incoming 689722
Internal Inter-Cell Handovers
 Handover Analysis-Inter-BSC Handover
Inter-BSC Outgoing Handover Failure Category
Inter-BSC Outgoing Handover Times
Commands, Requests, Successes, and CH332D:Failed Outgoing Ex- CH332K:Failed Outgoing Ex- H332Kc:Failed Outgoing Ex- H332Dp:Failed Outgoing Ex- H332Dc:Failed Outgoing Ex- The inter-BSC outgoing cell handover is
ternal Inter-Cell Handovers ternal Inter-Cell Handovers ternal Inter-Cell ternal Inter-Cell ternal Inter-Cell
Failures (Reconnection to Old Chan- (Handover Request Rejected) Handovers(No Radio Resource Handovers(Protocol Error Un- Handovers(Timer Expired ） mainly caused by :
nels) Available) specified)
CH330:Outgoing External Inter-Cell 135115H332DD:Failed Outgoing Ex- H332Dq:Failed Outgoing Ex- H332Kn:Failed Outgoing Ex- CH332C:Failed Outgoing Ex- H332Da:Failed Outgoing Ex-
(1) CH332D:Failed Outgoing External Inter-
Handover Requests ternal Inter-Cell
Handovers(No Activity on the
ternal Inter-Cell
Handovers(Other Causes)
ternal Inter-Cell
Handovers(Other Causes)
ternal Inter-Cell Handovers
(T8 Expired)
ternal Inter-Cell
Handovers(Abnormal Release,
Cell Handovers (Reconnection to Old
CH333:Successful Outgoing External 116362Radio Path) Unspecified) Channels)
Inter-Cell Handovers H332Kb:Failed Outgoing Ex-
ternal Inter-Cell
H332Ka:Failed Outgoing Ex-
ternal Inter-Cell
H332Dh:Failed Outgoing Ex-
ternal Inter-Cell
H332Kd:Failed Outgoing Ex-
ternal Inter-Cell
H332Df:Failed Outgoing Ex-
ternal Inter-Cell (2) CH332K:Failed Outgoing External Inter-
CH331:Outgoing External Inter-Cell
Handovers(Equipment Fail-
126924ure)
Handovers(OM Intervention) Handovers(Frequency Un-
available)
Handovers(Requested Terres-
trial Resource Unavailable)
Handovers(Handover Failed,
Timing Advance out of
Cell Handovers (Handover Request Rejected)
Handover Commands Range)

CH332:Failed Outgoing External Inter-Cell 18753 failure.

Handovers

Number of incoming inter-BSC handover Times Inter-BSC Incoming Handover Failure Category
requests, successes, detection, responses,
and failures
The incoming external inter-cell handover is
CH340:Incoming External Inter-Cell 130061 H342H:Failed Incoming Ex- H342HH:Cleared Incoming
ternal Inter-Cell Handovers External Inter-Cell Handovers mainly caused by the :
Handover Requests (Clear Commands Sent By By MSC(Other Causes)
361 (1) H342H:Failed Incoming External Inter-
111922 159 1598 698
MSC)
CH343:Successful Incoming External
Inter-Cell Handovers 161 CH342C:Failed Incoming Ex- H3429Ca:Failed Incoming Ex- Cell Handovers (Clear Commands Sent By
8 ternal Inter-Cell Handovers ternal Inter-Cell Handovers

CH341:Incoming External Inter-Cell 129698

81 (Timer Expired) (Timer Expired) (TCH) MSC)
Handover Responses
H342HB:Cleared Incoming
External Inter-Cell Handovers
H3429A:Failed Incoming Ex-
ternal Inter-Cell Handovers (2) H342HH:Cleared Incoming External Inter-
154 By MSC(Radio interface fail- (No Channel Available) (TCH)
Cell Handovers By MSC(Other Causes)
CH344:Incoming External Inter-Cell 117100 83 ure)
Handover Detection Messages Received failure.
by BSC
CH342:Failed Incoming External Inter-Cell 18139
Handovers
Handover Analysis-Parameter Check
PARA MO PARA ID PARA NAME network setting advise adjust reason License

SET GCELLSOFT ADAICFLAG Interference Cancel Mode OFF(1101) ON decrease uplink interference
Adaptation

SET GCELLHOBASIC MRINTRPLOPTSWITCH MR Interpolation Optimize NO(1101) YES the lost MR will be
compensated in linear way
for the rxqual and rxlev,
which will give more
handover chance to
improve drop.

SET GCELLBASICPARA ENCRY Encryption Algorithm A5/0-1&A5/1-0&A5/2- A5/0-1&A5/1-1&A5/2- decrease different

0&A5/3-0&A5/4-0&A5/5- 0&A5/3-1&A5/4-0&A5/5- Encryption Algorithms
0&A5/6-0&A5/7-0(3), 0&A5/6-0&A5/7-0 influence to handove
A5/0-1&A5/1-1&A5/2-
0&A5/3-1&A5/4-0&A5/5-
0&A5/6-0&A5/7-0(1098)

SET GCELLHOEMG NODLMRHOSTATTIME No Dl Mr. HO Statistic Time 1(1101) 3 decrease less MS

measurement' inaccurate
influence to handover

SET GCELLHOBASIC EDGESTAT1 Handover Algorithm I Edge 6(1101) 1 decreae th edge handover
HO Watch Time limit condition

SET GCELLBASICPARA MiccSwitch MICC Switch OFF(1101) ON decrease the uplink

interference

SET PSDTX PS DTX ENHANCEDDTX(927),OFF(1 ENHANCEDDTX reduce the PS to CS

GCELLPRIVATEOPTPARA 74) influence

SET GCELLPSPWPARA SUPPSDLPC DL EGPRS Closed-Loop NO(1101) YES reduce the PS to CS

Power Control Support influence

SET GCELLSOFT STIRCALLOWED EICC Allowed NO(1101) YES decrease uplink interference

SET GCELLPSPWPARA SUPGPRSDLPC DL GPRS Closed-Loop NO(1101) YES reduce the PS to CS

Power Control Support influence

SET GCELLPSPWPARA DLPCINITPR P0 DB0(1101) DB2 reduce the PS to CS

influence

SET GCELLHOEMG NODLMRHOLASTTIME No Dl Mr. HO Last Time 1(1101) 2 decrease less MS

Handover Analysis-Handover Failure Scenario
Proportion of Failures in Handover Failure(%)

Handover failed The main scenario is 100.00%

87.33
90.00%
(1) downlink interference 80.00%
68.72
(2) better cell handover proportion is small 70.00%

(3) Low incoming handover success rate. 60.00%

44.91
50.00%
40.00% 31.62 30.44
30.00% 24.59
20.00% 14 10.59 7.95
Handover Failure Scenario Failure Ratio 10.00% 4.19 3.11 0.06 0
(%) 0.00%

ce l e e ce e ge re es ct n e ge
al at at at ur ti o nc
High incoming handover success 24.595 re
n
sm ssr ssr re
n
ssr h an a ilu i l re je s re era
rfe is e e rfe e c er
f fa r ge rfe co
v
rate n
e
t o n u cc u cc n t e u cc i o n v v er o ve c on n te k
i rt i r s r s i r s rs d o o d f i a
l in
k
po ve ve l in
k ve ve h an a nd h an seo l i nk f we
Low incoming handover success 44.912 o o o o e h o
wn pr nd an
d up an
d
oi
c
el
ls
it e SC au up se
do v er ha h h f v -c - s B b ec n g a u
rate o g el g o ll tra er ct o c
a nd m
in l ev m
in se ce in i nt e je str e be
u P y r r
lh co w co ca TO an uc
h r lu
better cell handover proportion is 68.722 cel in Lo h
in
t be m m o ve f ai
r w d er
small tt e Lo Hi
g ec an
be r ej h d ov
er C n
o ve BS s ha
strong uplink interference 0.058 nd te
r
el
l
ha in l l-c
h h
many intra-site handover failures 7.949 uc uc ce
m m O P
T
much handoveer reject because of 13.999
voice version change
uplink interference 30.438
much inter BSC handover reject 4.193
TOP cell-cells handover failure 10.588
Handover Analysis-Summary of Optimization Measures
• Optimization Measures (For details, see the attachment.)
Handover
Before the optimization measures are implemented, strictly follow the three approvals and submit the RFC. Optimization Measure Summary.xls

PARAMETER PARAMETERNAME CURRENT VALUE AJUST VALUE

LEVSTAT,LEVLAST,INTERCELLHYST,PBGTSTAT,PBGT Layer HO Watch Time,Layer HO Valid Time,Inter-cell LEVSTAT(8),LEVLAST(6),INTERCELLHYST(68),PBGTST LEVSTAT(6),LEVLAST(4),INTERCELLHYST(65),PBGTST

MARGIN,PBGTLAST HO Hysteresis,PBGT Watch Time,PBGT HO AT(8),PBGTMARGIN(68),PBGTLAST(6) AT(6),PBGTMARGIN(65),PBGTLAST(4)
Threshold,PBGT Valid Time
INTERCELLHYST,PBGTMARGIN Inter-cell HO Hysteresis,PBGT HO Threshold INTERCELLHYST(68),PBGTMARGIN(68) INTERCELLHYST(70),PBGTMARGIN(70)

LEVSTAT,LEVLAST,PBGTLAST,PBGTSTAT Layer HO Watch Time,Layer HO Valid Time,PBGT LEVSTAT(8),LEVLAST(6),PBGTLAST(6),PBGTSTAT(8) LEVSTAT(6),LEVLAST(4),PBGTLAST(4),PBGTSTAT(6)

Valid Time,PBGT Watch Time
DIRMAGANSITEFLAG Directly Magnifier BTS Flag DIRMAGANSITEFLAG(NO) DIRMAGANSITEFLAG(YES)

INTERCELLHYST,MINOFFSET Inter-cell HO Hysteresis,Min Access Level Offset INTERCELLHYST(68),MINOFFSET(0) INTERCELLHYST(70),MINOFFSET(3)

DLEDGETHRES,ULEDGETHRES Edge HO DL RX_LEV Threshold,Edge HO UL RX_LEV DLEDGETHRES(20),ULEDGETHRES(10) DLEDGETHRES(23),ULEDGETHRES(13)

Threshold
HOTHRES,HOCDCMINDWPWR Inter-layer HO Threshold,Min DL Level on Candidate HOTHRES(25),HOCDCMINDWPWR(15) HOTHRES(22),HOCDCMINDWPWR(12)
Cell
 Access Analysis-KPI

3: Assignment Success Rate(%) is better than the benchmark value.(98%)

G: Immediate Assignment Success Rate(%) is less than the benchmark value.(95%)
4C:SDCCH Call Drop Ratio(%) is better than the benchmark value.(0.5%)

Access Theme KPI

RCA313: Assignment Success Rate(%) RA303G: Immediate Assignment Success Rate(%) ZTR104C:SDCCH Call Drop Ratio(%)
102 0.045
100 0.04

98 0.035
0.03
96
0.025
94
0.02
92
0.015
90
0.01
88 0.005
86 0
0 0 0 0 00 00 00 00 00 0 0 0 0 00 00 00 0 0 00 0 0 00 00 0 0 0 0 00 00 00 00 00 00 00 00 0 0 00 00 00 0 0 00 00 00 0 0
0 0: 0 0 : 0 0: 0 0: 0 0: 0 0: 0 0: 0 0: 0 0: 00 : 0 0: 0 0: 0 0: 0 0: 00 : 0 0 : 0 0: 0 0: 0 0: 0 0: 0 0: 0 0: 0 0: 0 0: 0 0: 00: 0 0: 0 0: 0 0 : 00: 0 0: 0 0: 0 0 : 0 0: 0 0: 00:
: : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : :
00 02 04 06 08 10 12 14 16 18 20 22 00 02 04 06 08 10 12 14 16 18 20 22 00 02 04 06 08 10 12 14 16 18 20 22
0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 7 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 8 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9 0 9
1 2- 1 2 - 12 - 1 2 - 1 2- 1 2- 1 2- 1 2- 1 2- 1 2- 1 2- 1 2- 1 2- 12 - 12 - 1 2 - 1 2- 1 2- 1 2- 12 - 1 2- 1 2- 1 2- 12 - 1 2 - 12 - 1 2- 1 2- 12 - 12 - 12 - 1 2- 1 2 - 1 2- 12 - 12 -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
0 19 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019 019
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
Access Analysis-Parameter Check
PARA MO PARA ID PARA NAME network setting advise adjust reason License

SET GCELLCCCH FMSMAXOPCC MS_TXPWR_MAX_CCH 0(3)(900M),5(819)(900M),5(9) 5(900)0(1800) MS get the best the initial
(1800M),0(270)(1800M) access power

SET GCELLSOFT ADAICFLAG Interference Cancel Mode OFF(1101) ON decrease uplink interference
Adaptation

SET GCELLTMR IMMREJWAITINDTIMER T3122 15(108),10(779),30(1),20(123), 10 Reduce the impact of

25(90) abnormal terminals.

SET GCELLBASICPARA MiccSwitch MICC Switch OFF(1101) ON decrease the uplink

interference

SET GCELLCCAD ASSRETRYMAX Max. Reassignments 1(664),3(437) 3 Increase the number of

reassignment times and
improve the assignment
success rate.

SET GCELLBASICPARA PDCH2SDEN Dynamic PDCH Conversion to NO(1101) YES Dynamic PDCHs can be
SDCCH Allowed converted to SDCCHs directly.

SET GCELLSOFT STIRCALLOWED EICC Allowed NO(1101) YES decrease uplink interference

SET GCELLPSPWPARA SUPGPRSDLPC DL GPRS Closed-Loop Power NO(1101) YES reduce the PS to CS influence
Control Support

SET GCELLPSPWPARA DLPCINITPR P0 DB0(1101) DB2 reduce the PS to CS influence

SET GCELLCCTMR N200PARASWITCH Use LAPDm N200 ON(1059),OFF(42) ON reduce the timer unproper
settings' influence to drop.

SET GCELLSOFT ADAICADFLAG Enhanced Interference Cancel OFF(1101) ON decrease uplink interference
Mode Adaptation

SET GCELLBASICPARA IMMASSEN TCH Immediate Assignment YES(1),NO(1100) NO Increase the immediate
Allowed assignment success rate

SET GCELLHOBASIC INTERFHOEN Interference HO Allowed NO(434) YES Reduce switch towards

SET GCELLTMR ESTABINDTIMER T3101 2000(3) 3000 Reserve sufficient time for the
MS to access the network.
 Access Analysis-Immediate Assignment

Access failures before assignment are mainly caused by:

(1) immediate assignment failure
(2) TCH failures
(3) CA304:Call Setup Indications Timed Out.

Number of occurrence times of each subcounter

6646317
6614697
5780223
6 00 0 00 0

4 00 0 00 0

2 00 0 00 0 817883
31620
31249
131441706 1381 266 194 162 75 19 15
0
 Access Analysis-Assignment

signment failure is mainly caused by the

12Aa:Failed Assignments during MOC on the A Interface (Including Directed Retry)
129C:Failed Assignments (First Assignment, Assignment Timed Out)
12Ca:Failed Assignments during MTC on the A Interface (Including Directed Retry).

Number of occurrence times of each subcounter

135524
1 6 00 0 0
1 2 00 0 0
110606
80000
6995967020
40000 16010 8666 4825 4803 1300 405 221 208 194 1 1 1
0
Access Analysis-Access Failure Scenario
Proportion of Failures in Access Failure Scenarios(%)
100.00% 90.36
Access failure The main scenario is 90.00%
80.00%
(1) downlink interference 70.00% 61.73 59.88
60.00%
(2) good neighbours 50.00%
47.59 43.61
34.16
(3) much weak uplink rxlev access. 40.00%
30.00% 21.39
20.00% 12.09
10.00% 5.16 3.42 0.11
0.00%

Access Failure Scenario Failure Ratio

(%)
SDCCH sequcence drops 5.164
assignment failure(transmission 0.111
error)
General Scenario 43.613
Congestion(TCH) 12.089
SDCCH equipment drops 3.421
Weak Coverage Access Increases 34.162
Because Neighboring Cells Are
Out of Service
uplink interference 47.587
good neighbours 61.727
Congestion(SDCCH) 21.394
downlink interference 90.357
Access Analysis-Summary of Optimization Measures
• Optimization Measures (For details, see the attachment.)
Access Optimization
Before the optimization measures are implemented, strictly follow the three approvals and submit the RFC. Measure Summary.xls

PARAMETER PARAMETERNAME CURRENT VALUE AJUST VALUE

PDCH2SDEN Dynamic PDCH Conversion to SDCCH Allowed PDCH2SDEN(NO) PDCH2SDEN(YES)

CELLMAXSD Cell SDCCH Channel Maximum CELLMAXSD(80) CELLMAXSD(160)

TCHBUSYTHRES TCH Traffic Busy Threshold TCHBUSYTHRES(1) TCHBUSYTHRES(0)

RXMIN Minum Access RXLEV RXMIN(8) RXMIN(10)

RACHACCLEV CS RACH Min. Access Level RACHACCLEV(-109) RACHACCLEV(-106)

MSMAXRETRAN MS MAX Retrans MSMAXRETRAN(4_Times) MSMAXRETRAN(2_Times)

CRO Cell Reselect Offset CRO(3) CRO(1)

ULQUALIMIT,DLQUALIMIT UL Qual. Threshold,DL Qual. Threshold ULQUALIMIT(55),DLQUALIMIT(55) ULQUALIMIT(45),DLQUALIMIT(45)

HQI Analysis-KPI

Uplink HQI is less than the benchmark value.

Downlink HQI is less than the benchmark value.

HQI Analysis-KPI(%)
100

99

98

97

96 Standard line
95
Uplink HQI
94

93
Downlink HQI
92
0 0 0 0 0
00 00 0 00 000 00 00 00 00 00 00 00 00 00 00 00 00 00
:0 :0 :0 :0 :0
0: 0: :0 0: :0
0: 0: 0: 0: 0: 0: 0: 0 0: 0 0: 0 0: 0 0: 0 0: 0 0: 0 0:
00 00 00 00 00 0 0 00 0 000 0 0 0 0 0 0
0:
0 0 3: 0 0 6: 1 19: 1 2:
21
:
00
:5: 03
: 8:
06
:
09
:
12
:
15
:
18
:
21
:
00
:
03
:
06
:
09
:
12
:
15
:
18
:
21
:
7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 9 9 9 9 9 9 9 9
2 - 0 2- 0 2 - 0 2 - 0 2 - 0 2 - 0 2- 0 2- 0 2- 0 2- 0 2- 0 2- 0 2- 0 2- 0 2 - 0 2 - 0 2- 0 2- 0 2- 0 2- 0 2- 0 2- 0 2 - 0 2 - 0
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 9- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19- 19-
20 20 20 20 20 20 20 20 20 20 20 2 0 2 0 2 0 20 20 20 20 20 20 20 20 20 20
 HQI Analysis-RxLev RxQual Distribution
uplink level <= -90dBm is 71.6%, and the uplink coverage is Weak Coverage (threshold 50%).
80]. quality [6/7]= 0.0%, uplink The interference is normal. (threshold 1%).
l <= -90dBm ratio is 41.56%, and the downlink coverage is Weak Coverage (threshold 40%).
= -80]. quality [6/7]= 0.68%, downlink The interference is normal. (threshold 1%).

Uplink HQI Downlink HQI

800000 700000

700000 600000

600000
500000
500000
400000
400000 RxLev RxLev
300000
300000
200000
200000 7 (>-70) 7 (>-70)
6 (-75~-70) 6 (-75~-70)
100000 100000
5 (-80~-75) 5 (-80~-75)
4 (-85~-80) 4 (-85~-80)
0 3 (-90~-85) 0 3 (-90~-85)
Quality Quality 2 (-95~-90) Quality Quality 2 (-95~-90)
level 0 level 1 Quality Quality 1 (-100~-95) level 0 level 1 Quality Quality 1 (-100~-95)
level 2 level 3 Quality Quality 0 (<-100) level 2 level 3 Quality Quality 0 (<-100)
level 4 level 5 Quality Quality level 4 level 5 Quality Quality
level 6 level 7 level 6 level 7
HQI Analysis-HQI Failure Scenario
Proportion of Failed HQIs in Failed Scenarios(%)

HQI failed The main scenario is 50.00%

44.57
(1) neighbor cell is better than serving cell 45.00%
40.2
(2) downlink interference 40.00%

(3) uplink interference. 35.00% 33.07

30.00%

25.00%

HQI Failure Scenario Failure Ratio 20.00%

(%) 15.00%

10.00%
TCH TRXs are better BCCH TRX 4.718 4.72
5.00%
1.5 0.25
strong uplink interference 0.246
0.00%

BCCH TRX is better TCH TRXs 1.498 ll ce ce X Xs e

ce n n TR nc
ng fe
re
fe
re TR fr e
re
uplink interference 33.070 rv
i e r e r CH H
te
se in
t
in
t
B C
r TC in
n k k r t e k
ha lin lin tt e et li n
downlink interference 40.204 rt wn up
e b up
t te eb is
b e do ar X ng
neighbor cell is better than serving 44.568 is Xs TR ts ro
ll TR CH
ce H
cell bo
r
TC BC
h
ig
ne
HQI Analysis-Parameter Check
PARA MO PARA ID PARA NAME network setting advise adjust reason License

SET GCELLBASICPARA FRDLDTX FR Use Downlink DTX YES(927),NO(174) YES reduce downlink interference

SET GCELLBASICPARA HRDLDTX HR Use Downlink DTX YES(927),NO(174) YES reduce downlink interference

SET GCELLBASICPARA MiccSwitch MICC Switch OFF(1101) ON decrease the uplink

interference

SET GCELLPRIVATEOPTPARA PSDTX PS DTX ENHANCEDDTX(927),OFF(174 ENHANCEDDTX reduce the PS to CS influence

)

SET GCELLCHMGBASIC CHALLOCSTRATEGY Channel Allocate Strategy CAPABILITY(664),QUALITY(43 QUALITY Channel Allocation Quality
7) Factor First

SET GCELLPWR3 AMRCALLPCALLOWED Allow III Power Control For ON(437),OFF(664) ON enable AMR power
AMR control ,reduce intra-network
interference.

SET GCELLBASICPARA UPPCEN UL PC Allowed YES(864),NO(237) YES Power control is enabled to

reduce intra-network
interference.

SET GCELLPSPWPARA SUPPSDLPC DL EGPRS Closed-Loop Power NO(1101) YES reduce the PS to CS influence
Control Support

SET GCELLBASICPARA HRULDTX HR Uplink DTX Shall_NOT_Use(174),Shall_Use Shall_Use reduce uplink interference
(927)

SET GCELLBASICPARA FRULDTX FR Uplink DTX Shall_NOT_Use(174),Shall_Use Shall_Use reduce uplink interference
(927)

SET GCELLBASICPARA DNPCEN DL PC Allowed YES(864),NO(237) YES Power control is enabled to

reduce intra-network
interference.

SET GCELLPSPWPARA SUPGPRSDLPC DL GPRS Closed-Loop Power NO(1101) YES reduce the PS to CS influence
Control Support

SET GCELLPSPWPARA DLPCINITPR P0 DB0(1101) DB2 reduce the PS to CS influence

SET GCELLPSCHM MAXPDCHRATE Maximum Rate Threshold of 50(1056) 30 Reduce the PS interference to
PDCHs in a Cell the CS.

SET GCELLHOBASIC INTERFHOEN Interference HO Allowed NO(434) YES Reduce switch towards
HQI Analysis-Summary of Optimization Measures
• Optimization Measures (For details, see the attachment.)
HQI Optimization
Before the optimization measures are implemented, strictly follow the three approvals and submit the RFC. Measures Summary.xls

PARAMETER PARAMETERNAME CURRENT VALUE AJUST VALUE

RXMIN Minum Access RXLEV RXMIN(8) RXMIN(10)

RACHACCLEV CS RACH Min. Access Level RACHACCLEV(-109) RACHACCLEV(-106)

INTELEVHOHYST Adjacent Cell Inter-layer HO Hysteresis INTELEVHOHYST(67) INTELEVHOHYST(57)

HOTHRES Inter-layer HO Threshold HOTHRES(30) HOTHRES(33)

INTERCELLHYST,PBGTMARGIN Inter-cell HO Hysteresis,PBGT HO Threshold INTERCELLHYST(68),PBGTMARGIN(68) INTERCELLHYST(66),PBGTMARGIN(66)

ULQUALIMITAMRHR,DLQUALIMITAMRHR,ULQUALI UL Qual. Limit for AMR HR,DL Qual. Limit for AMR ULQUALIMITAMRHR(55),DLQUALIMITAMRHR(55),U ULQUALIMITAMRHR(50),DLQUALIMITAMRHR(50),U
MITAMRFR,DLQUALIMITAMRFR HR,UL Qual. Limit for AMR FR,DL Qual. Limit for LQUALIMITAMRFR(55),DLQUALIMITAMRFR(55) LQUALIMITAMRFR(50),DLQUALIMITAMRFR(50)
AMR FR
ULQUALIMIT,DLQUALIMIT UL Qual. Threshold,DL Qual. Threshold ULQUALIMIT(55),DLQUALIMIT(55) ULQUALIMIT(50),DLQUALIMIT(50)

CRO Cell Reselect Offset CRO(3) CRO(1)

INTERCELLHYST Inter-cell HO Hysteresis INTERCELLHYST(68) INTERCELLHYST(66)

DLEDGETHRES Edge HO DL RX_LEV Threshold DLEDGETHRES(25) DLEDGETHRES(28)

DLEDGETHRES,ULEDGETHRES Edge HO DL RX_LEV Threshold,Edge HO UL RX_LEV DLEDGETHRES(20),ULEDGETHRES(10) DLEDGETHRES(23),ULEDGETHRES(12)

Threshold
ULQUALIMITAMRFR,DLQUALIMITAMRFR UL Qual. Limit for AMR FR,DL Qual. Limit for AMR ULQUALIMITAMRFR(55),DLQUALIMITAMRFR(55) ULQUALIMITAMRFR(50),DLQUALIMITAMRFR(50)
FR
HOCDCMINDWPWR Min DL Level on Candidate Cell HOCDCMINDWPWR(15) HOCDCMINDWPWR(18)

STIRCALLOWED,ADAICADFLAG,ADAICFLAG EICC Allowed,Enhanced Interference Cancel Mode STIRCALLOWED(NO),ADAICADFLAG(OFF),ADAICFLA STIRCALLOWED(YES),ADAICADFLAG(ON),ADAICFLA

Adaptation,Interference Cancel Mode Adaptation G(OFF) G(ON)
 Thank you
www.huawei.com
www.huawei.com

HUAWEI TECHNOLOGIES CO., LTD.