Mix Designs

Exposure Condition: Exposure Conditions of the structure: The

general environment to which the concrete will be exposed during its
service life, is categorized into five class to severity, as per IS 456.
The exposure condition limits the minimum cement content, maximum
water – cement ratio and minimum grade of concrete.
As per exposure condition, you have the above data for working the first
trial and arriving its mix proportion.
If you are getting desired result at a lower cement content, you need to put
extra as mentioned by IS 456.

•Minimum thickness of member: Size of aggregate should not be

more than one-fourth of the minimum thickness of member, mostly
20 mm nominal size aggregate is suitable for most works. It is
always suggested to go the maximum nominal size of aggregate to
save on quantity of cement per unit of concrete.
•Cement Grade : Cement type/grade locally available that can be
made available throughout construction period
•Workability : Placing condition of concrete governs its workability,
low – slump of 25-75 mm (lightly reinforced sections in slab, beam,
column) to high –  slump of 100-150 mm (slip form, pumped
concrete)
Stipulation for Proportioning Concrete Ingredients

(a) Characteristic compressive strength required in the field at 28 days grade designation — M 30

(b) Type of Cement : OPC 53 Grade confirming to IS 12269

(b) Maximum Nominal size of aggregate — 20 mm

(c) Shape of CA — Angular

(d) Workability required at site — 100 mm (slump)

(e) Type of exposure the structure will be subjected to (as defined in IS: 456) — Moderate

(h) Method of concrete placing: pump able concrete

Test Data of Material
The following materials are to be tested in the laboratory and results are to be ascertained for the design mix:
Cement Used : OPC 53 Grade Confirming to IS 12269
Specific Gravity of Cement : 3.15
Chemical admixture : Super plasticizer confirming to IS 9103
Specific gravity
Specific gravity of Fine Aggregate (sand) : 2.70
Specific gravity of Coarse Aggregate : 2.80
Water Absorption
Coarse Aggregate : 0.4%
Fine Aggregate : 1.0%
Free (surface) moisture
Coarse Aggregate : Nil
Fine Aggregate : Nil
Aggregate are assumed to be in saturated surface dry condition usually while preparing design mix.
Seive Analysis
Fine aggregates : Confirming to Zone I of Table 4 IS – 383 
•Determining the Target Strength for Mix Proportioning
•F’ck = fck + 1.65 x S
•Where,

•F’ck = Target average compressive strength at 28 days

•Fck = Characteristic compressive strength at 28 days
•S = Assumed standard deviation in N/mm2 = 5 (as per table -
1 of IS 10262- 2009)
•= 30 + 1.65 x 5.0 = 38.25 N/mm2
•Note : Under control conditions if Target average
compressive strength is achieved then at field the probability
of getting compressive strength of 30 MPa is very high
• From Table 5 of IS 456, Maximum water-
cement ratio = 0.50
• Note : Do not start with w/c ratio above
0.50,even though the other desired results
like Strength, workability could be achieved.
• Maximum water content for 20 mm
aggregate = 186 Kg (for 25 to 50 slump)
• We are targeting a slump of 100mm, we
need to increase water content by 3% for
every 25mm above 50 mm i.e. increase 6%
for 100mm slump
• i.e. Estimated water content for 100 Slump =
186+(6/100) X 186 = 197 litre
• Water content = 197 liters
calculation of Cement Content
Water-Cement Ratio = 0.50
Water content from Step – 3 i.e. 197 liters
Cement Content = Water content / “w-c ratio” = (197/0.50) = 394 kgs
From Table 5 of IS 456,
Minimum cement Content for moderate exposure condition = 300 kg/m3
394 kg/m3 > 300 kg/m3, hence, OK.
As per clause 8.2.4.2 of IS: 456
Maximum cement content = 450 kg/m3, hence ok too
• Proportion of Volume of Coarse Aggregate and Fine aggregate
Content
• From Table 3 of IS 10262- 2009, Volume of coarse aggregate
corresponding to 20 mm size and fine aggregate (Zone I) = 0.60
• Note 1: In the present case water-cement ratio is 0.5.So there will be
no change in coarse aggregate volume i.e. 0.60 .

• Note 2: Incase the coarse aggregate is not angular one, then also
volume of coarse aggregate may be required to be increased suitably
based on experience.
Estimation of Concrete Mix calculations

The mix calculations per unit volume of concrete shall be as follows:

Volume of concrete = 1 m3

Volume of cement = (Mass of cement / Specific gravity of cement) x (1/100) =

(39/3.15) x (1/1000) = 0.125 m3
Volume of water = (Mass of water / Specific gravity of water) x (1/1000) = (197/1) x
(1/1000) = 0.197 m3
Total Volume of Aggregates = 1- (b+c) =1- (0.125+0.197) = 0.678 m3

Mass of coarse aggregates = d X Volume of Coarse Aggregate X Specific Gravity of

Coarse Aggregate X 1000 = 0.678 X 0.60 X 2.80 X 1000 = 1139 kgs/m3
Mass of fine aggregates = d X Volume of Fine Aggregate X Specific Gravity of Coarse
Aggregate X 1000 = 0.678 X 0.40 X 2.70 X 1000 = 732 kgs/m3
Concrete Mix Proportions for Trial Mix
Mix Proportions for trial Mix-1:
Cement = 394 kg/m3
Water = 197 kg/m3
Fine aggregates = 732 kg/m3
Coarse aggregate = 1139 kg/m3
Water-cement ratio = 0.50
• Note-1: Aggregates should be used in saturated surface dry condition. If otherwise, when
computing the requirement of water, allowance shall be made for the free (surface) moisture
contributed by coarse aggregate and fine aggregate. On the other hand, if the aggregates are
already dry , the amount of water mixed should be increased by an amount equal to the moisture
likely to be absorbed by the aggregates. Necessary adjustments are also required to be made in the
mass of the aggregates. The surface water and percenetage water abosorption shall be determined
according to IS 2386.
• Correction in water content due to absorption or moist aggregates
• The slump shall be measured and the water content and shall be adjusted for achieving the
required slump based on trial, if required. The mix proportions shall be reworked for the actual
water content and checked for durability requirements.
• Two more trials having variation of +/- 10% of water cement ratio  shall be carried out and a graph
between three water-cement ratios and their corresponding strength shall be plotted to work out
the mix proportions for the given target strength for field trials. However, durability requirement
shall be met.
Mix Proportions for trial Mix-2
If achieved workability is more than targeted say 125mm. Reduce water content by 3% (for every 25 mm increase)
Water Content for Trial 2
Water content = 197 – (3/197)*100 = 191 liters
Calculation of Cement Content for Trial 2
Water-Cement Ratio                         = 0.50
Water content for Trial 2 = 191 liters
Cement Content = Water content / “w-c ratio” = (191/0.50) = 382 kgs
From Table 5 of IS 456,
Minimum cement Content for moderate exposure condition = 300 kg/m3
394 kg/m3 > 300 kg/m3, hence,  OK.
As per clause 8.2.4.2 of IS: 456
Maximum cement content = 450 kg/m3, hence ok too.
Proportion of Volume of Coarse Aggregate and Fine aggregate Content
If the mix is cohesive and slump was true ,we can infer that there would be no change in Volume of coarse aggregate = 0.60
Estimation of Concrete Mix Calculations

The mix calculations per unit volume of concrete shall be as follows:

Volume of concrete = 1 m3

Volume of cement = (Mass of cement / Specific gravity of cement) x (1/100) = (382/3.15) x (1/1000) = 0.121 m3

Volume of water = (Mass of water / Specific gravity of water) x (1/1000) = (191/1) x (1/1000) = 0.191 m3

Total Volume of Aggregates = 1- (b+c) =1- (0.121+0.191) = 0.688 m3

Mass of coarse aggregates = d X Volume of Coarse Aggregate X Specific Gravity of Coarse Aggregate X 1000 = 0.688 X 0.60 X 2.80 X 1000 = 1155 kgs/m3

Mass of fine aggregates = d X Volume of Fine Aggregate X Specific Gravity of Coarse Aggregate X 1000 = 0.688 X 0.40 X 2.70 X 1000 = 743 kgs/m3

Final Concrete Mix proportions for Trial Number 2

Cement = 382 kg/m3

Water = 191 kg/m3

Fine aggregates = 743 kg/m3

Coarse aggregate = 1155 kg/m3

Water-cement ratio = 0.50

Mix Proportions for Trial Mix-3

Sand being of Zone – I i.e. coarser ,If achieved concrete appears to be under sanded ,coarse aggregate is prominent and the mix is non-cohesive (not able to form ball).

Increase sand proportion in increments of 3%, coarse aggregate proportion will reduce by 3%.

Water Content for Trial 3

Water content = 197 liters (Trial -1)

Calculation of Cement Content for Tril 2

Water-Cement Ratio                         = 0.50

Water content for Trial 3 = 197 liters

Cement Content = Water content / “w-c ratio” = (197/0.50) = 394 kgs

From Table 5 of IS 456,

Minimum cement Content for moderate exposure condition = 300 kg/m3

394 kg/m3 > 300 kg/m3, hence, OK.

As per clause 8.2.4.2 of IS: 456

• Maximum cement content = 450 kg/m3, hence ok too.
• Proportion of Volume of Coarse Aggregate and Fine aggregate Content
• The mix is non-cohesive (under sanded), we need to Increase sand proportion in
increments of 3% and coarse aggregate proportion to be reduced by 3%.
• Volume of coarse aggregate = 60 – 3% = 57%
Estimation of Concrete Mix Calculations

The mix calculations per unit volume of concrete shall be as follows:

Volume of concrete = 1 m3

Volume of cement = (Mass of cement / Specific gravity of cement) x (1/100) = (394/3.15) x (1/1000) = 0.125 m3

Volume of water = (Mass of water / Specific gravity of water) x (1/1000) = (197/1) x (1/1000) = 0.197 m3

Total Volume of Aggregates = 1- (b+c) =1- (0.125+0.197) = 0.678 m3

Mass of coarse aggregates = d X Volume of Coarse Aggregate X Specific Gravity of Coarse Aggregate X 1000 = 0.678 X 0.57 X 2.80 X
1000 = 1082 kgs/m3
Mass of fine aggregates = d X Volume of Fine Aggregate X Specific Gravity of Coarse Aggregate X 1000 = 0.678 X 0.43 X 2.70 X 1000 =
787 kgs/m3
Final Concrete Mix proportions for Trial Number 3
Cement = 394 kg/m3
Water = 197 kg/m3
Fine aggregates = 787 kg/m3
Coarse aggregate = 1082 kg/m3
Water-cement ratio = 0.50
• Step 6: Estimation of the mix ingredients
• a) Volume of concrete = 1 m3 
• b) Volume of cement = (Mass of cement / Specific gravity of cement)
x (1/100) = (383.2/3.15) x (1/1000) = 0.122 m3 
• c) Volume of water = (Mass of water / Specific gravity of water) x
(1/1000) = (191.6/1) x (1/1000) = 0.1916 m3 
• d) Volume of total aggregates = a – (b + c ) = 1 – (0.122 + 0.1916) =
0.6864 m3 
• e) Mass of coarse aggregates = 0.6864 x 0.558 x 2.84 x 1000 =
1087.75 kg/m3 f)
• Mass of fine aggregates = 0.6864 x 0.442 x 2.64 x 1000 = 800.94
kg/m3
• Aliphatic superplasticizer/water reducing admixture/Concrete
admixture & Mortar admixture
• Product Name: Aliphatic superplasticizer
• Product Description
• Aliphatic superplasticizer/water reducing admixture/Concrete
admixture & Mortar admixture
• Water reducing rate 25%
• With the dosage of 1.0-2.0% of CL-ZF
• Tested by Shanlv P.O.42.5 ordinary portland cement
• Materials fully chemical reaction → pure appearance→stable
quality 。
• China Giant Concrete Admixtures and Concrete Additive Types as Follows:
• Type A—Water-reducing admixtures & additive,
• Type B—Retarding admixtures & additive,
• Type C—Accelerating admixtures & additive,
• Type D—Water-reducing and retarding admixtures & additive,
• Type E—Water-reducing and accelerating admixtures & additive,
• Type F—Water-reducing, high range admixtures & additive,
• Type G—Water-reducing, high range, and retarding admixtures & additive.
• Type H—High range water-reducing, high range, and retarding admixtures &
additive.
• Type I—High range retarding admixtures & additive
• TypeJ—Water-reducing, high range, and retarding admixtures & additive.
• TypeK—China Giant concrete admixtures Water-reducing, high range, and retarding admixtures &
additive.
• TypeL—China manufacture Water-reducing, high range, and retarding admixtures & additive.
• China Giant concrete admixtures Aliphatic superplasticizer/water reducing admixture/Concrete
admixture & Mortar admixture is for high water reducing complies with the requirements of the
following standards: ASTM C 494, Type E & F. BS EN 934-2.2.technical cooperation services on
heatless and automatic system for export to Sudan,Pakistan,Africa,middle east,Brazil,South 
Africa,Mexico,Angola,Algeria,Morocco,UAE,ect.
• Specifications:
• (1) Powder (with a solid content ≥95%, solid, suitable for a long-distance transportation) , or liquid
(with a solid content of 20%-50%).

• (2) With a high slump retention ability, without concrete segregation, with a much smaller slump
loss than that of other superplasticizers.
• (3) With a good dispersion, an excellent adaptability to different cements, and good water-reducing
properties. A high water-reducing ratio up to 25% could be obtained when used in high strength
grade concrete.(higher than C50). With a dosage of 1.0-2.0%,water reducing rate up to 25%.
• (4) Low chloride content, and no corrosion to steel.
•  (5) Cement paste fluidity ≥230mm (with a dosage of 1.0-2.0%).
• Applications:
• (1) Used in high performance and high strength concrete with high construction
requirements.
• (2) Used in high slump concrete, ready mixed concrete, and pumping concrete.  
• (3) Used in the concrete of high buildings, hydraulic engineering, transport system,
port engineering, and municipal engineering etc.  
• (4) Used in other high-lift concrete for specific buildings.  
•  Uses and Cautions:
• (1) A recommended dosage is 1.0%-2.0%. Actual dosages should be determined by
mixture design test according to concrete strength grade.

• (2) It is required that the tolerance must be less than 0.2%.   

• (3) 0℃-40℃ the shelf life of liquid products is 12 months. After expiration date,
concrete test must be carried out to confirm the quality.  
• (4) Concrete test must be carried out before utilization.
• (5) This product is forbidden to be mixed with naphthalene superplasticizers.
• (6) Experiment must be done when it is used together with other admixtures.
End