CHAPTER Four

CONTROL UNIT

1
O UTLINE
 4.1 Introduction
 4.2 Micro-operations
 4.3 Control Unit
 Functional Requirements
 Inputs
 Outputs
 Control Signals
 4.4 Control Unit
Implementation
 Hardwired Control Unit
2
4.1 I NTRODUCTION
 In Chapter 3, seen:
 Machine instructions
 Operations performed by the processor to
execute each instruction
 But how exactly each individual
operation is caused to happen ?
 The job of the Control Unit

 The control unit

 Portion of the processor t h a t actually causes things
to happen by
 Issuing a control signal 3
 Internal as well as external to the processor
4.2 M ICRO -O PERATIONS
 A computer executes a program
 Consists of a sequence of instruction cycles
 Instruction cycle
 Consists of the following smaller cycles
 Fetch/indirect/execute/interrupt cycle
 Each cycle in turn, involves a series of steps
 These steps are called micro-operations
 A single micro-operation does verylittle and
generally involves either of the following
 A transfer between registers
 A transfer between a register and an external bus or
 A simple ALU operation

 Atomic operation of CPU 4

M ICRO -O PERATIONS ...
 A diagram showing the relationship among
the concepts discussed so far

5
M ICRO -O PERATIONS ...
 In the next sections, we will see
 How the events of any instruction cycle
ca n be described as a sequence of micro
operations

 How the concept of micro operations serve as a

guide to the design of the control unit

6
M ICRO -O PERATIONS ...
 Fetch cycle
 Sequence of events, seen from point of view of its effects on
processor registers

 First Step
 To move the address from PC to MAR

 Second Step
 Overall effect is to bring in the instruction
 Address (in the MAR) is placed on address bus
 Control unit issues READ command
 Result (data from memory) appears on d ata bus
 D ata from data bus copied into MBR
 PC incremented by 1 (in parallel with data fetch from memory)

 Third Step
 D ata (instruction) moved from MBR to IR 7
M ICRO -O PERATIONS ...
 Fetch cycle (symbolic)
 t1: MAR  (PC)
 t2: MBR  memory
PC  (PC) +1
 t3: IR  (MBR)

 Fetch cycle
 Involves three steps and four µop
 Note t h a t each µop involves movement of d a t a into or out of
a register
 Several µops can be performed in one clock cycle, so
long as these movements do not interfere with one 8
another
M ICRO -O PERATIONS ...
 Assumptions
 A clock is available for timing purpose
 It emits regularly spaced clock pulses
 Each clock pulse defines a time unit

 Each single micro operation can be performed within

a time of a single time unit
 Nota tions t 1,t2 and t 3 represents successive
tim e units

 Note
 The second an d third micro operations (µops) , both ,
takes place during the second time unit
 The third µop could have been grouped 9
with the fourth without affecting the fetch operation
M ICRO -O PERATIONS ...
 Rules for grouping of µops
 Proper sequence of events mus t be followed
 MAR  (PC) m ust precede MBR  (memory)
 As memory read operation makes use of the address in

the MAR
 Conflicts mu st be avoided
 Must not read & write same register in one time unit
 As the result would be unpredictable

 MBR  memory a nd IR  (MBR) m ust not be in same

cycle

10
M ICRO -O PERATIONS ...
 Indirect Cycle
 t1: MAR  (IR[Address])
 t2: MBR  memory
 t3: IR(Address) 
(MBR[Address])
 Note:
 IR[Address]
 Refers to the address field of the instruction

 MBR contains a n address

 IR is now in the same state as if direct addressing
had been used 11
M ICRO -O PERATIONS ...
 Interrupt Cycle
 t1 : MBR  (PC)
 t2: MAR  Save_Address
PC  Routine_Address
 t3: memory  (MBR)

 Note:
 Save_Address
 The address a t which the contents of the PC are to be saved
 Routine_Address
 The starting address of the interrupt processing routine

 This is a minimum
 May be additional micro-ops to get addresses
 The na t ure of this cycle varies greatly from one machine to another
12
M ICRO -O PERATIONS ...
 Fetch, Indirect and Interrupt Cycles
 Simple and predictable
 E ach involves a sm all, fixed of micro
sequence operations
 In each case, the same sequence of micro operations
repeated

13
M ICRO -O PERATIONS ...
 Execute Cycle
 Different for each instruction
 For a machine with N different opcodes
 N different sequence of micro operation

 Example:
 ADD R1,X
 (add the contents of location X to Register 1 , result in R1)
 t1: MAR  (IR[Address])
 t2: MBR  memory
 t3: R1  (R1) + (MBR)

14
M ICRO -O PERATIONS ...
 Execute Cycle
 Example:
 ISZ X
(increment and skip if zero)
 t 1: MAR  (IR[Address])
 t 2: MBR  memory
 t 3: MBR  (MBR) + 1
 t 4: memory  (MBR)
if ((MBR) == 0) t he n
PC  (PC) + 1

15
M ICRO -O PERATIONS ...
 So far we have seen
 How the operation of the processor can be defined as
a sequence of micro operations

 Next
 How the control unit causes this sequence to occur

16
4.3 C ONTROL U NIT
 Functional Requirements
 Functional requirements of the control unit,
those functions the control unit m us t perform,
 Basis for the design a nd implementation of the
control unit

 The control unit h as to perform two basic tasks

 Sequencing
 Cause the processor to step through a series of µops ,in

the proper sequence

 Execution

 Cause each µop to be performed

 This is done using Control 17

Signals
C ONTROL U NIT ...
 For the control u nit to perform its function,
it needs
 Inputs
 To determine the state of the system

 Outputs
 To control the behaviour of the system

 The above are external specification of the

control unit

 Internally the control unit

 Must have the logic required to perform its
function 18
 Sequencing
 Execution
C ONTROL U NIT ...
 Inputs
 Clock
 Used by control unit to keep time
 One µops or a set of parallel µops occur per clock
cycle
 Instruction register
 Contains Op-code
 Determines of current
which µops instruction
a re performed during th e
execute cycle
 Flags
 Used by control unit to determine the stat us of CPU
 Also, to determine results of previous ALU operations

 From control bus

 Interrupts 19
 Acknowledgements
C ONTROL U NIT ...
 Outputs
 Control signals within CPU
 These are two types
 Cause da t a movement

 Activate specific ALU functions

 Control signals to control bus

 These are also two types
 Control signals to memory

 Control signals to I/O modules

20
C ONTROL U NIT ...
 Model of Control Unit

21
C ONTROL U NIT ...
 How does the control unit maintain control ?
 Control signals
 Example : consider the fetch cycle
 Control unit generates the following control signals
 MAR  (PC)
 Open gates between PC and MAR

 MBR  memory

 Open gates between MAR and address bus

 Memory read control signal

 Open gates between data bus and MBR

 Add 1 to contents of PC and store the result back to PC

 IR  (MBR) 22
 Open gates between MBR and IR
C ONTROL U NIT ...
 Dat a P a t hs and
Control Signals

23
C ONTROL U NIT ...
 Maintains a knowledge of where it is in
the instruction cycle
 Reads all of its inputs

 Emits a sequence of control signals

 That causes the right µops to occur at the

right time
 The control unit is the engine that
runs the entire computer
24
4.4 C ONTROL U NIT I MPLEMENTATION
 Two ways to implement the control unit:
 Hardwired Control Unit Implementation
 Micro programmed Control Unit Implementation

25
H ARDWIRED I MPLEMENTATION
 The control unit is essentially a combinational
circuit
 Its inputs logic signals are transformed into a set
of output logic signals which are the control
signals

26
H ARDWIRED I MPLEMENTATION ...
 Control Unit Inputs
 Flags and control bus signals
 Each individual bit typically has some meaning

 The other two inputs (instruction register and clock) are

not directly useful to the control unit
 Need to be modified as shown below

 Instruction register
 The control unit makes use of the opcode to issue different
combination of control signals for different instruction
 To simplify the control unit logic, there should be a unique logic
input for each opcode
 Performed by a decoder

 A decoder with n binary inputs will have 2 n binary outputs

 For any combination of inputs only on of its output is high 27
H ARDWIRED I MPLEMENTATION ...
 Control Unit Inputs
 Clock
 Generates a repetitive sequence of pulses
 Useful for measuring duration of micro-ops

 The control unit emits different control signals a t different

times within instruction cycle
 Realized using a counter as inputs to control unit

 Which generates different control signals

• T1,T2,T3….
 At the end of each instruction cycle, the control unit feeds
back to the counter to reinitialize it a t T1

28
H ARDWIRED I MPLEMENTATION ...
 Control Unit with Decoded Inputs

29
H ARDWIRED I MPLEMENTATION ...
 Control Unit Internal Logic
 Derive a boolean expression for each control signal as
a function of the inputs
 Example:
 Consider two control signals P a nd Q with the following
characteristics
 PQ= 00 Fetch cycle
 PQ=01 Indirect cycle
 PQ=10 Execute cycle
 PQ=11 Inte rrupt cycle
 Then the boolean expression for C5 (a control signal t h a t

causes the da t a to be read from the external d at a bus into

MBR)
 C5=P’Q’T2 + P’QT2

 (C5 will be asserted during the second time unit of both the 30
fetch and indirect cycles)
H ARDWIRED I MPLEMENTATION ...

 Control Unit Internal Logic

 Repeat the above process for every control
signal generated by the CU
 Result
 A set of boolean equations tha t define the behavior of the
control unit
 Problems With Hardwired Designs
 Complex sequencing & micro-operation logic
 Difficult to design and test
 Inflexible design
 Difficult to add new instructions 31
End of Chapter 4

32