Scribd
Upload
31 views

Unit 2 Switching

This chapter discusses different types of switched networks, including circuit-switched networks, datagram networks, and virtual circuit networks. It provides examples to illustrate each type. For circuit-switched networks, it notes that each connection uses a dedicated path and channel on each link. For datagram networks, it notes that packets are divided into fixed or variable sizes and resources are allocated on demand. For virtual circuit networks, it discusses addressing and the three phases of connection setup, data transfer, and teardown. It also covers the structure of switches used in different network types.

Uploaded by

Utkarsh Kumar
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
31 views

Unit 2 Switching

This chapter discusses different types of switched networks, including circuit-switched networks, datagram networks, and virtual circuit networks. It provides examples to illustrate each type. For circuit-switched networks, it notes that each connection uses a dedicated path and channel on each link. For datagram networks, it notes that packets are divided into fixed or variable sizes and resources are allocated on demand. For virtual circuit networks, it discusses addressing and the three phases of connection setup, data transfer, and teardown. It also covers the structure of switches used in different network types.

Uploaded by

Utkarsh Kumar
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 36

Chapter 2

Switching
Dr. Kamlesh Chandravanshi
School of Computer Science & Engineering
Figure 2.1 Switched network
Figure 2.2 Taxonomy of switched networks
2-1 CIRCUIT-SWITCHED NETWORKS

A circuit-switched network consists of a set of switches


connected by physical links. A connection between two
stations is a dedicated path made of one or more links..
However, each connection uses only one dedicated
channel on each link.. Each link is normally divided
into n channels by using FDM or TDM.

Topics discussed in this section:


Three Phases
Efficiency
Delay
Circuit-
Switched
Technology
Note

A circuit-switched network is made of a


set of switches connected by physical
links, in which each link is
divided into n channels.
Figure 2.3 A trivial circuit-switched
network
Note

In circuit switching, the resources need


to be reserved during the setup phase;
the resources remain dedicated for the
entire duration of data transfer until
the teardown phase.
Example 2.1

As a trivial example, let us use a circuit-switched network


to connect eight telephones in a small area.
Communication is through 4-kHz voice channels. We
assume that each link uses FDM to connect a maximum
of two voice channels. The bandwidth of each link is then
8 kHz. Figure 2.4 shows the situation. Telephone 1 is
connected to telephone 7; 2 to 5; 3 to 8; and 4 to 6. Of
course the situation may change when new connections
are made. The switch controls the connections.
Figure 2.4 Circuit-switched network used in Example 2.1
Example 2.2

As another example, consider a circuit-switched network


in two remote offthat connects computers ices of a private
company. The offices are connected using a T-1 line
leased from a communication service provider. There are
two 4 × 8 (4 inputs and 8 outputs) switches in this
network. For each switch, four output ports are folded
into the input ports to allow communication between
computers in the same office. Four other output ports
allow communication between the two offices. Figure 2.5
shows the situation.
Figure 2.5 Circuit-switched network used in Example 2.2
Figure 2.6 Delay in a circuit-switched network
Note

Switching at the physical layer in the


traditional telephone network uses
the circuit-switching approach.
2-2 DATAGRAM NETWORKS

In data communications, we need to send messages


from one end system to another. If the message is
going to pass through a packet-switched network, it
needs to be divided into packets of fixed or variable
size.. The size of the packet is determined by the
network and the governing protocol.
[10101010100] frame [fixed, varible]

Topics discussed in this section:


Routing Table
Efficiency
Delay
Datagram
Networks in
Note

In a packet-switched network, there


is no resource reservation;
resources are allocated on demand.
Figure 2.7 A datagram network with four switches
(routers)
Figure 2.8 Routing table in a datagram
network
Note

A switch in a datagram network uses a


routing table that is based on the
destination address.
Note

The destination address in the header of


a packet in a datagram network
remains the same during the entire
journey of the packet.
Figure 2.9 Delay in a datagram network
Note

Switching in the Internet is done by


using the datagram approach
to packet switching at
the network layer.
2-3 VIRTUAL-CIRCUIT NETWORKS

A virtual-circuit network is a cross between a circuit-


switched network and a datagram network. It has
some characteristics of both.

Topics discussed in this section:


Addressing
Three Phases
Efficiency
Delay
Circuit-
Switched
Technology
in WANs
Figure 2.10 Virtual-circuit network
Figure 2.11 Virtual-circuit identifier
Figure 2.12 Switch and tables in a virtual-circuit network
Figure 2.13 Source-to-destination data transfer in a virtual-circuit network
Figure 2.14 Setup request in a virtual-circuit network
Figure 2.15 Setup acknowledgment in a virtual-circuit network
Note

In virtual-circuit switching, all packets


belonging to the same source and
destination travel the same path;
but the packets may arrive at the
destination with different delays
if resource allocation is on demand.
Figure 2.16 Delay in a virtual-circuit network
Note

Switching at the data link layer in a


switched WAN is normally
implemented by using
virtual-circuit techniques.
2-4 STRUCTURE OF A SWITCH

We use switches in circuit-switched and packet-


switched networks. In this section, we discuss the
structures of the switches used in each type of
network.

Topics discussed in this section:


Structure of Circuit Switches
Structure of Packet Switches
Figure 2.17 Crossbar switch with three inputs and four outputs
Figure 2.18 Multistage switch
Note

In a three-stage switch, the total


number of crosspoints is
2kN + k(N/n)2
which is much smaller than the
number of
crosspoints in a single-stage switch (N2).
Example 2.3

Design a three-stage, 200 × 200 switch (N = 200) with


k = 4 and n = 20.

Solution
In the first stage we have N/n or 10 crossbars, each of size
20 × 4. In the second stage, we have 4 crossbars, each of
size 10 × 10. In the third stage, we have 10 crossbars,
each of size 4 × 20. The total number of crosspoints
is 2kN + k(N/n)2, or 2000 crosspoints. This is 5 percent of
the number of crosspoints in a single-stage switch (200 ×
200 = 40,000).

You might also like