PLAIN & REINFORCED CONCRETE-1

CE-313

Lecture # 1

Introduction
By. Manoj Balakrishnan
Plain & Reinforced Concrete-1
Syllabus-I

Plain Concrete
 Constituent material of concrete and their properties.
 Hydration of cement.
 Properties of fresh and hardened concrete and factors effecting them.
 Curing of concrete and its significance.
 Testing of concrete for various properties including physical tests, strength
tests.
 Crushing or ultimate strain.
 Modulus of elasticity of concrete, types, tests. Determination and significance.
 Design of normal concrete mixes, factors affecting the workability of the fresh
concrete and strength & durability of the hardened concrete.
 Alkali aggregate reaction, carbonation and sulfate attack.
 Additives and admixtures for concrete.
 Cracks in concrete.
Plain & Reinforced Concrete-1
Syllabus-II

Mechanics of Reinforced Concrete

 Basics of composite action of steel and concrete.
 Stress-strains curves of steel and concrete.
 Actual, simplified and equivalent stress blocks.
 Behavior of reinforced concrete members including columns, beams and slabs
at working and ultimate loads.
 Specifications, codes of practice and design loads.
 Analysis, design and detailing of
 Simply supported rectangular and T-beam by ultimate strength design
method
 Simply supported and continuous one way and two way slabs.
 Reinforced concrete members for axial compression and tension.
 Tied and spiral columns.
 ACI code provisions for design of columns.
Plain & Reinforced Concrete-1
Syllabus-III

Mechanics of Reinforced Concrete (contd…)

 Shear and diagonal tension in concrete, design and detailing of flexural
members for shear.
 Corner reinforcement in slabs.
 Assessment of crack width in flexural members.
 Introduction to alternate method of design with applications

Practical
 Physical testing of constituent material for concrete.
 Acceptance test for cement.
 Test on fresh and reinforced concrete for workability, compressive strength,
tensile strength, modulus of rupture and modulus of elasticity.
 Casting of different types of beams and columns and testing to study the
effects of various factors.
 Detailing of designed elements.
Plain & Reinforced Concrete-1

 Text Book
 Design of Concrete Structures (13th Edition)
by Arthur H. Nilson, David Darwin & Charles W.
Dolan

 References
 Reinforced Concrete (5th Edition) by Edward G.
Nawy
 Building Code Requirements for Structural Concrete
(ACI 318-05)
Plain & Reinforced Concrete-1
Concrete
Concrete is a mixture of cement, fine and coarse
aggregate.
Concrete mainly consists of a binding material and filler material. If filler
material size is < 5mm it is fine aggregate and > 5mm is coarse aggregate.
Plain Cement Concrete (PCC)
Mixture of cement , sand and coarse aggregate without
any reinforcement is known as PCC.
PCC is strong in compression and week in tension. Its tensile strength is so
small that it can be neglected in design.
Reinforced Cement Concrete (RCC)
Mixture of cement , sand and coarse aggregate with
reinforcement is known as RCC. (Tensile strength is improved)
Plain & Reinforced Concrete-1
Reinforced Cement Concrete (RCC) contd..
Mix Proportion
Cement : Sand : Crush
1 : 1.5 : 3
1 : 2 : 4
1 : 4 : 8
Water Cement Ratio (W/C)
W/C = 0.5 – 0.6
For a mix proportion of 1:2:4 and W/C = 0.5, if cement is 50 kg
Sand = 2 x 50 = 100 Kg
Crush = 4 x 50 = 200 Kg Batching By Weight
Water = 50 x 0.5 = 25 Kg
Plain & Reinforced Concrete-1

Mechanism of Load Transfer Load

Roof
Function of structure is Surface
to transfer all the loads
Roof Slab
safely to ground.
A particular structural Beams
member transfers load
to other structural Column
member.
Foundatio
n

Sub Soil
 Plain & Reinforced Concrete-1
Merits of Concrete Construction
1. Good Control over cross sectional dimensions and Shape
One of the major advantage of concrete structures is the full
control over the dimensions and structural shape. Any size and
shape can be obtained by preparing the formwork accordingly.
2. Availability of Materials
All the constituent materials are earthen materials (cement, sand,
crush) and easily available in abundance.
3. Economic Structures
All the materials are easily available so structures are economical.
4. Good Insulation
Concrete is a good insulator of Noise & heat and does not allow
them to transmit completely.
 Plain & Reinforced Concrete-1
Merits of Concrete Construction (contd…)
5. Good Binding Between Steel and Concrete
there is a very good development of bond between steel and
concrete.
6. Stable Structure
Concrete is strong in compression but week in tension and steel as
strong in tension so their combination give a strong stable
structure.
7. Less Chances of Buckling
Concrete members are not slim like steel members so chances of
buckling are much less.
8. Aesthetics
concrete structures are aesthetically good and cladding is not
required
 Plain & Reinforced Concrete-1
Merits of Concrete Construction (contd…)
9. Lesser Chances of Rusting
steel reinforcement is enclosed in concrete so chances of rusting
are reduced.
Demerits of Concrete Construction
10. Week in tension
Concrete is week in tension so large amount of steel is required.
11. Increased Self Weight
Concrete structures have more self weight compared with steel
structures so large cross-section is required only to resist self
weight, making structure costly.
12. Cracking
Unlike steel structures concrete structures can have cracks. More
cracks with smaller width are better than one crack of larger
width.
 Plain & Reinforced Concrete-1
Demerits of Concrete Construction
4. Unpredictable Behavior
If same conditions are provided for mixing, placing and curing
even then properties can differ for the concrete prepared at two
different times.
5. Inelastic Behavior
concrete is an inelastic material, its stress-strains curve is not
straight so its behavior is more difficult to understand.
6. Shrinkage and Creep
Shrinkage is reduction in volume. It takes place due to loss of water
even when no load is acting over it. Creep is reduction in volume
due to sustained loading when it acts for long duration. This
problem is not in steel structures.
7. Limited Industrial Behavior
Most of the time concrete is cast-in-situ so it has limited industrial
behavior.
Plain & Reinforced Concrete-1
Specification & Codes
These are rules given by various organizations in
order to guide the designers for safe and
economical design of structures
Various Codes of Practices are
1. ACI 318-05 By American Concrete Institute. For
general concrete constructions (buildings)
2. AASHTO Specifications for Concrete Bridges. By
American Association of State Highway and
Transportation Officials.
3. ASTM (American Standards for Testing and
Materials) for testing of materials.
Plain & Reinforced Concrete-1
Specification & Codes (contd…)
No code or design specification can be construed
as substitute for sound engineering judgment in
the design of concrete structures. In the structural
practice, special circumstances are frequently
encountered where code provisions can only serve
as a guide, and engineer must rely upon a firm
understanding of the basic principles of structural
mechanics applied to reinforced or pre-stressed
concrete, and the intimate knowledge of nature of
materials
Plain & Reinforced Concrete-1
Design Loads
 Dead Load
“The loads which do not change their magnitude and
position w.r.t. time within the life of structure”
Dead load mainly consist of superimposed loads and self load of
structure.

 Self Load
It is the load of structural member due to its own
weight.
 Superimposed Load
It is the load supported by a structural member. For
instance self weight of column is self load and load of
beam and slab over it is superimposed load.
Plain & Reinforced Concrete-1
Design Loads (contd…)
 Live Load
“Live loads consist chiefly of occupancy loads in buildings
and traffic loads on bridges”
 They may be either fully or partially in place or not
present at all, and may also change in location.
 Their magnitude and distribution at any given time are
uncertain, and even their maximum intensities
throughout the life time of the structure are not known
with precision.
 The minimum live loads for which the floor and roof of
a building should be designed are usually specified in
the building codes that governs at the site construction .
Plain & Reinforced Concrete-1
Densities of Important Materials
Material Density (Kg/m3)
PCC 2300
RCC 2400
Brick masonry 1900-1930
Earth/Sand/Brick ballast 1600-1800

Intensities of Live Loads (Table 1.1, Design of concrete structures by Nilson)

Occupancy / Use Live Load(Kg/m2)
Residential/House/Class Room 200
Offices 250-500
Library Reading Room 300
Library Stack Room 750
Warehouse/Heavy storage 1250
 Plain & Reinforced Concrete-1
Basic Design Equation
Applied Action x F.O.S = Max. Internal Resistance
Factor of Safety
F.O.S. = Max. Failure load/Max. Service Load
Following points are relevant to F.O.S
1. It is used to cover uncertainties due to
1. Applied loads
2. Material strength
3. Poor workmanship
4. Unexpected behavior of structure
5. Thermal stresses
6. Fabrication
7. Residual stresses
2. If F.O.S is provided then at service loads deflection and cracks are
within limits.
3. It covers the natural disasters.
Concluded