MACHINE DRAWING

PART-B
www.Jntufastupdates.com 2
www.Jntufastupdates.com 3
For the subject having design and / or drawing, (such as Engineering Graphics,
Engineering Drawing, Machine Drawing) and estimation, the distribution shall be
30 marks for internal evaluation (20 marks for continuous Assessment (day–to–day
work) and 10 marks for internal tests) and 70 marks for end examination.

There shall be two internal tests in a Semester for 10 marks each and final marks can
be calculated with 80% weightage for better of the two tests and 20% weightage for
other test and these are to be added to the marks obtained in day to day work.

www.Jntufastupdates.com 4
 MACHINE DRAWING
PART-B

II. Assembly Drawings:

Objective: The student will be able to draw the assembly from the individual part
drawing.
Drawings of assembled views for the part drawings of the following using conventions
and easy drawing proportions.
a) Engine parts –Gear pump, Fuel pump Petrol Engine connecting rod, piston assembly.
b) Other machine parts - Screws jacks, Machine Vices Plummer block, Tailstock.
c) Valves: spring loaded safety valve, feed check valve and air cock, Control valves

5
 STUFFING BOX
It is used to prevent loss of fluid such as steam, between sliding or turning parts of machine elements. In a
steam engine, when the piston rod reciprocates through the cylinder cover; stuffing box provided in the
cylinder cover, prevents leakage of steam from the cylinder.
Figure shows (next slide) the various parts of a stuffing box. At the base of stuffing box body 1, a bush 3 is
placed such that the bevelled edge of the bush is at the inner side of the body. Gland 2 is placed at the other
end of the body and is connected to the main body by means of studs 4 and nuts 5. The space between the
reciprocating rod and the bush and the gland is packed with a packing material such as mineral fibres,
leather, rubber or cork.
Assemble all parts of the stuffing box for a vertical steam engine, shown in Fig. (below) and draw, (i) half
sectional view from the front, with left half in section, (ii) half sectional view from the right and (iii) view
from above.
 STEAM ENGINE CROSSHEAD

Crosshead is used in horizontal steam engines for connecting the piston rod and connecting
rod. Figure (Above) shows the part drawings of a steam engine crosshead. The crosshead,
with the help of slide block 4, reciprocates between two guides provided in the engine frame.
The gudgeon pin 3, connects the slide blocks with the crosshead block 1. This acts as a pin
joint for the connecting rod (not shown in figure). The piston rod 2 is secured to the crosshead
block by means of the cotter 5.
The assembly ensures reciprocating motion along a straight line for the piston rod and
reciprocating cum oscillatory motion for the connecting rod.
Assemble the parts and draw, (i) half sectional view from the front, with bottom half in section and (ii) view
from above.
11
 ECCENTRIC

Assemble the parts and draw, (i) half sectional view from the front,
with top half in section, (ii) view from the right and (iii) view from
above.
It is used to provide a short reciprocating motion, actuated by the rotation of a shaft. Eccentrics are used for operating steam valves, small pump
plungers, shaking screens, etc. The sheave 2 which is in the form of a circular disc with a stepped rim is keyed on the shaft. When the shaft
rotates, the sheave rotates eccentrically because of the eccentrically placed hole in it and imparts reciprocating motion to eccentric rod 6.
The straps 1 are semi-circular elements with an annular recess to accommodate the stepped rim of the sheave. These are held together on the
sheave by means of strap bolts 4, with packing strips 3 placed between them. The eccentric rod is fixed to the eccentric strap by means of the
studs and nuts 5.
 PISTON

A piston is cylindrical in form and reciprocates in a cylinder. The petrol engine

piston is generally die cast in aluminium alloy. It is connected to the small end of the
connecting rod by means of a gudgeon pin. Figure (above) shows the details of the
petrol engine piston assembly.

Five piston rings 4 are positioned in the piston 1; four at the top and one at the bottom. The top
piston rings, known as compression rings, prevent leakage of gases from combustion chamber
into the crank case. The bottom one; oil or scraper ring, prevents the lubricating oil from
entering the combustion chamber.
The piston is connected to the small end of the connecting rod, by means of the gudgeon or
piston pin 2; the axial movement of which is prevented by piston plugs 3.
Assemble the parts of the piston, shown in Fig. 18.6 and draw the following views:
(i) Sectional view from the front, (ii) Half sectional view from the left, and
 PETROL ENGINE CONNECTING ROD
Figure (below) shows the assembly drawing of a petrol engine connecting rod, the big end of which is split
into two halves. It is used in center crank engines.
The bearing bush 4 which is in one piece, is fitted at the small end of the connecting rod 1. The small end of the rod is
connected to the piston. The main bearing bush, which is split into two halves, is placed at the big end of the connecting
rod. The big end of the rod is connected to the crank pin of the center crank. First, the split bearing brasses 3 are placed
on the crank pin, then the big end of the connecting rod and the cap 2 are clamped onto these, by means of two bolts 5 and
nuts 6.
 SCREW JACK
• Screw jacks are used for raising heavy loads through very small heights.
• Figure (Below) shows the details of one type of screw jack.
• In this, the screw 3 works in the nut 2 which is press fitted into the main body 1. The tommy bar 7 is
inserted into a hole through the enlarged head of the screw and when this is turned, the screw will move
up or down, thereby raising or lowering the load.
Assemble all parts of the screw jack, shown in Fig, and draw the following views:
(i) Half sectional view from the front, and
(ii) View from above.
 LATHE TAIL-STOCK
• It is a part of a lathe machine and is used to support lengthy jobs. To accommodate works of different lengths between
centres, the tail-stock may be moved on the lathe bed to the required position and clamped by means of a clamping
bolt. Figure shows various parts of a tail-stock.
• The barrel 2 is fitted into the bore of the tail-stock body 1 and is prevented from rotation by the feather key 9 placed
underneath of it. The barrel has a threaded portion at its end and the spindle 3 is inserted into the barrel through this.
• The hand wheel 6 is mounted on the spindle by a key and is retained in position by a nut. The spindle bearing 5 is
placed between the hand wheel and the tail-stock body. A tapered hole provided at the front end of the barrel, receives
the dead centre 4 or a tapered shank of the drill or reamer.
• When the hand wheel is operated, the barrel is made to move in or out of the tail-stock body. In the required position of
the barrel, clamping may be made by means of the clamping lever 7 and stud 8 which is fitted to the tail-stock
body. The spindle bearing is fixed to the body by means of the screws 10.
• Assemble the parts and draw to a suitable scale, (i) sectional view from the front and (ii) view from the left.
 MACHINE VICE
• The details of a plain machine vice are shown in Fig. 18.22.
• It consists of the base 1 which is clamped to the machine table using two T-bolts.
• The sliding block 3 is fixed in the centre slot of the base by means of the guide screw 4.
• The movable jaw 2 is fixed to the sliding block with four screws 8 and 7.
• One of the serrated plates 5 is fixed to the jaw of the base by means of screws 6 and the
other to the movable jaw by the screws 7.
• One end of the guide screw is fixed to the base by means of the washer 9 and nut
10 (not shown in figure).
• The movable jaw is operated by means of a handle (not shown) which fits onto the
square end of the guide screw.

• Assemble the parts and draw, (i) sectional view from the front, (ii) view from above and
(iii) view from the left. Use suitable scale.
 SWIVEL MACHINE VICE
• A machine vice is a work holding device, used in machines such as drilling, milling, etc. A
swivelling type machine vice permits swivelling about its vertical axis, so that the work may be
clamped at any angular position required in the machining operation. T-bolts (not shown) are used
through the base plate, to fix the vice to the machine table. Figure 18.23 shows the details of a
swivel machine vice.
• It consists of the swivel body 1 which is fixed to the base plate 3 by two bolts 6. The heads of the
bolts are so shaped, that they can slide freely in the circular T-slot of the base plate. The
graduations marked in degrees on the flange of the base plate, facilitate setting of the swivel body
at any desired angle.
• The swivel body has a fixed jaw at one end. The movable jaw 2 is mounted on the swivel body by
the screw 4. After the screw is inserted fully, it is held in position by a nut and pin to prevent its
axial motion. Thus, when the screw is turned, the movable jaw slides on the swivel body guide
ways. Steel jaw plates 5 are fitted to jaws by machine screws.
Figure. Swivel Machine Vice
31
32
 AIR COCK
This valve is used to control air
or gas supply. The details of an
air cock are shown in Fig.
18.32.
It consists of a plug 2 which is
inserted into the body 1, from
the bottom. The rectangular
sectioned spring 4 is placed in
position at the bottom of the
plug and seated over the screw
cap 3. The screw cap is
operated to adjust the spring
tension. Lever 5 with square
hole is used to operate the
cock. By a mere 90° turn, the
cock is either opened or closed
fully.
 RAMSBOTTOM
SAFETY
It is a boiler mounting and a safety
VALVE device which protects the boiler
against building-up of excess
pressure. The spring used in the
safety valve is set to act when the
steam pressure exceeds the set
value and allows the steam to
escape. Thus, only the permissible
value of steam pressure is allowed
inside the boiler.
It consists of housing 1 with two valve chests. The valve seats 3 are screwed into the housing and valves 2 are located in the
valve seats. The eye bolt 8 is fastened to the bridge of the housing, by means of washer 9 and both the nuts 10 and 11. Pivot
4 is pinned to the lever 5 and it is placed over the valves and held in position by safety links 7 and spring 6. The safety
links 7 are fixed at one end to the lever and the other end to the eye bolt 8 by pins 12 and split pins 13. The required
rigidity is provided to this assembly by fixing the spring 6 between the eye bolt and the lever (holes are provided in the
lever and eye bolt for this purpose). When the set value of the pressure exceeds in the boiler, the lever moves and allows
the valves to get lifted from the seats concerned. The movement of the lever is permitted due to the slot provided centrally
in it and returns to the original position due to spring action.
 BLOW-OFF
COCK

The blow-off cock is fitted at the lowest part of the boiler, to remove the sediments collected. When operated, water and
sediments rush through the side flange of the cock (due to pressure in the boiler) and escape through the bottom flange.
Figure 18.33 shows the parts of a blow-off cock. It consists of a hollow conical body 1 into which the cock 2 is
located. Both the cock and body have vertical slots and when they are aligned, water gushes through the cock. Gland 3
is fastened
 It is used in boilers to regulate the supply
of feed water and to maintain the water
level. It is fitted close to the boiler shell
and in the feed pipe line. Figure shows
the details of a feed check valve. The
valve prevents water from being returned
to the supply line, due to steam pressure
in the boiler. Hence, it functions like a
non-return valve.

FEED CHECK VALVE

It consists of a body with two flanges at right angle and feed water enters at the bottom and enters the boiler through the
side opening. The valve seat 5 is introduced into the body of the valve from the top opening. The valve 4 is located in the
valve seat, which guides the movement of the valve. The spindle 3 is screwed from bottom of the cover 2 such that, the
square end of the spindle projects out through the cover. Studs 8 are screwed to the body and the spindle and cover
assembly is fastened to the body by nuts 10. Studs 9 are screwed to the cover and the gland 6 is inserted into the
cover and tightened by nuts 11. To prevent the leakage of water through the cover, packing material is introduced
between the cover and gland. Hand wheel 7 is located on the spindle such that, the square hole in the hand wheel meshes
with the square portion of spindle. The hand wheel is fixed to the spindle by nut 11. By operating the hand wheel,
the spindle
permits the valve to get lifted from the valve 56