Industrial Safety Supply,
Inc.
Francisco A. Lopez
Industrial Safety Supply, Inc.
BRADY PRINTERS
Industrial Safety Supply, Inc.
RAE GAS DETECTOR
Multi Rae Lite QRAE III TOXI Rae Pro
Personal
Protective
Equipment
Industrial Safety Supply, Inc.
LOCK OUT TAG OUT
Industrial Safety Supply, Inc.
BREATHING APPARATUS
Industrial Safety Supply, Inc.
FARO SCANNER
Industrial Safety Supply, Inc.
Gas Detector instruments are designed to protect personnel
From unseen hazard that may exist in workplace environments,
Including confined spaces.
Industrial Safety Supply, Inc.
Monitor and detect of up to four ( 4 ) gases with ten ( 10 )
sensors to choose. With man down alarm system, easy to
maintain and replace sensor in workplace
Industrial Safety Supply, Inc.
Industrial Safety Supply, Inc.
Accessories of QRAE III
1. A.C adapter
2. Pro RAE studio II Software
3. Power supply 100v to 240v
4. PC Communication cable
5. Hydrophobic filter
6. Alligator clip
7. T-Hose or calibration tube hose
8. Calibration Certificate
9. Charging and adapter for PC Communication
Industrial Safety Supply, Inc.
PARTS OF THE QRAE III
Gas Inlet
Filter
LED Alarm
Sensor Port
LCD Display
Mode Key Y / + Key
Alarm
LED Alarm
Industrial Safety Supply, Inc.
TURNING THE UNIT ON
Press and Hold the Mode button for 3 seconds.
During start up, the battery , buzzer , vibration alarm and LEDs are tested
And then the unit performs self-testing of its functions. When the main measurement
Screen appears the unit is ready for calibration or use.
Mode button
Mode button
Industrial Safety Supply, Inc.
TURNING THE UNIT OFF
Press and hold the Mode button wit in 5 seconds count down
To shutoff.
If you remove your finger from the key during the countdown .
The shutoff operation is canceled and the unit continuous operation
Mode button
Mode button
Industrial Safety Supply, Inc.
Charging time 5 Hours unit off
Li-ion battery provides up to 14 hours
Continuous for diffusion model and
11 hours for pumped model
Industrial Safety Supply, Inc.
Manual Span calibration and Bump Test
Calibration Regulator Calibration T- Hose Calibration Gas Illustration
Calibration tube
Industrial Safety Supply, Inc.
MANUAL SPAN CALIBRATION
To begin calibration, connect the calibration gas cylinder
Flow regulator and T-Hose to the unit
Enter Programming Mode by pressing and Holding Mode Button
And Y/+ Button simultaneously until the password screen appears
Input the 4 digit password. Default password is 0000
Select
Mode button
Y/+
Industrial Safety Supply, Inc.
BUMP TESTING – Is a brief exposure to the gas in order to verify that the sensor respond
Within a specific boundary and the detector’s alarm function properly.
SPAN CALIBRATION – Is a resetting of the detectors response against a known concentration
of target gas, in a balance of synthetic air or Nitrogen. This will determine
the relationship between the detectors reading and the actual
concentration
of the component gas of interest.
Industrial Safety Supply, Inc.
The company must
provide
required equipment:
Testing and monitoring
Ventilation
Communications
Lighting
Barriers
Other personal protective
equipment
Any required rescue and
emergency equipment
Industrial Safety Supply, Inc.
TWO METHOD ON HOW TO USE THE GAS DETECTOR
WITH SAMPLE PROBE
DIFFUSION SAMPLING
ASSEMBLY
Industrial Safety Supply, Inc.
WITH SAMPLE PROBE
Measure and indicate the concentration of present Toxic and Combustible gases in the certain environment
Industrial Safety Supply, Inc.
DIFFUSION SAMPLING ( Continuous Monitoring )
Measure and indicate the concentration of present Toxic and Combustible gases in the certain environment
Industrial Safety Supply, Inc.
REMINDER
In the event of an alarm condition, it is important to follow established procedures.
The safest course of action is to immediately LEAVE the affected area, and to
return only after further testing determines that the area is once again safe for
entry. Failure to immediately leave the area may result in serious INJURY or
DEATH
Industrial Safety Supply, Inc.
Using PRORAE II software
Industrial Safety Supply, Inc.
MONITORING
Industrial Safety Supply, Inc.
AFTERSALES SERVICE AND WARRANTY
2 year warranty on the device against factory defect.
3 years warranty for the Oxygen, LEL, CO, H2S Sensors
1 year warranty on the Battery
Free service charge ( Labor cost ) on any repair of gas detector
Free annual checkup and servicing of this unit
Free Installation and calibration of your unit upon purchase of expired sensor
Industrial Safety Supply, Inc.
AFTER SALES SERVICE
TRAINING
We provide free training and orientation on how to use and
maintain the Gas Detector
SERVICE UNIT
TOP-RIGID Provide 1 (one) service unit in case customers Gas Detector
is for pull out for further check-up by the technician.
Industrial Safety Supply, Inc.
Industrial Safety Supply, Inc
THANK YOU
We VALUE safety. We CARE for your
SAFETY
