Scribd
Upload
28 views

Diatm: Rajbandh, Durgapur, West Bengal

This document describes a Bluetooth controlled car project using an Arduino board. It lists the group members and components used, which include an Arduino UNO, DC motors, Bluetooth module, motor driver, batteries, and a toy car. It explains that the Android phone acts as the transmitter to send movement commands like forward, backward, left, right to the Bluetooth module receiver on the car. The circuit diagram and code explanation show how the Arduino controls the motor driver and DC motors to move the car based on commands received from the Bluetooth module serial connection.

Uploaded by

Prashant Shekhar
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
28 views

Diatm: Rajbandh, Durgapur, West Bengal

This document describes a Bluetooth controlled car project using an Arduino board. It lists the group members and components used, which include an Arduino UNO, DC motors, Bluetooth module, motor driver, batteries, and a toy car. It explains that the Android phone acts as the transmitter to send movement commands like forward, backward, left, right to the Bluetooth module receiver on the car. The circuit diagram and code explanation show how the Arduino controls the motor driver and DC motors to move the car based on commands received from the Bluetooth module serial connection.

Uploaded by

Prashant Shekhar
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 12

DIATM

Rajbandh , Durgapur , West Bengal


GROUP’S MEMBERS
Prashant Shekhar (EC/16/32)
Abhijeet Kumar Dubey (EC/16/19)
Mayank Kumar (EC/16/31)
Ashwini Kumar (EC/16/29)
Uttam Kumar (EC/16/34)
Danish Khan (EC/16/33)
PRESENTION ON :-

Bluetooth Controlled Car


using Arduino
Components:-
Arduino UNO
DC Motors
Bluetooth module HC-05
Motor Driver L293D
9 Volt Battery and 6 volt battery
Battery Connector
Toy Car
Bluetooth controlled car is controlled by using Android mobile
phone instead of any other method like buttons, gesture etc. Here
only needs to touch button in android phone to control the car in
forward, backward, left and right directions. So here android phone is
used as transmitting device and Bluetooth module placed in car is
used as receiver. Android phone will transmit command using its in-
built Bluetooth to car so that it can move in the required direction
like moving forward, reverse, turning left, turning right and stop.
 
Bluetooth Module
HC Bluetooth module consists two things one is Bluetooth serial
interface module and a Bluetooth adaptor. Bluetooth serial module is
used for converting serial port to Bluetooth.
 
How to operate Bluetooth module?
You can directly use the Bluetooth module after purchasing from market, because
there is no need to change any setting of Bluetooth module. Default baud rate of
new Bluetooth module is 9600 bps. You just need to connect rx and tx to
controller or serial converter and give 5 volt dc regulated power supply to module.
Bluetooth module has two modes one is master mode and second one is slave
mode. User can set either mode by using some AT commands. Even user can set
module’s setting by using AT command. Here is some commands uses are given:
First of all user need to enter AT mode with 38400 bps baud rate by pressing EN
button at Bluetooth module or by giving HIGH level at EN pin. Note: all
commands should ends with \r\n (0x0d and 0x0a) or ENTER KEY from keyboard.

Pin Description of accelerometer


1. STATE  → Open
2. Rx  → Serial receiving pin
3. Tx  → Serial transmitting pin
4. GND   → ground
5. Vcc     → +5volt dc
6. EN       → to enter in AT mode5.
Working Explanation
In this project we have used a toy car for demonstration. Here we have selected a RF toy
car with moving left right steering feature. After buying this car we have replaced its RF
circuit with our Arduino circuit. This car have two dc motors at its front and rear side.
Front side motor is used for giving direction to car means turning left or right side (like
real car steering feature). And rear side motor is used for driving the car in forward and
backward direction. A Bluetooth module is used to receive command from android
phone and Arduino UNO is used for controlling the whole system.
Circuit Diagram and Explanation :-
Circuit diagram for bluetooth controlled car is shown in above figure. A Motor
driver is connected to arduino to run the car. Motor driver’s input pins 2, 7, 10 and 15
are connected to arduino's digital pin number 12, 11, 10 and 9 respectively. Here we
have used two DC motors to driver car in which one motor is connected at output pin
of motor driver 3 and 6 and another motor is connected at 11 and 14.  A 6 volt Battery
is also used to power the motor driver for driving motors. Bluetooth module’s rx and
tx pins are directly connected at tx and rx of Arduino. And vcc and ground pin of
Bluetooth module is connected at +5 volt and gnd of Arduino. And a 9 volt battery is
used for power the circuit at Arduino’s Vin pin

Program Explanation :-
 In program first of all we have defined output pins for motors.
#define m11 11 // rear motor
#define m12 12
#define m21 10 // front motor
#define m22 9

And then in setup, we gave directions to pin.


void setup()
{
Serial.begin(9600); pinMode(m11, OUTPUT);
pinMode(m12, OUTPUT);
pinMode(m21, OUTPUT);
pinMode(m22, OUTPUT);
}
After this we read input by using serial communication form Bluetooth module and
perform the operation accordingly.
void loop()
{
while(Serial.available())
{
char ch=Serial.read();
str[i++]=ch;

if(str[i-1]=='1')
{
Serial.println("Forward");
forward();
i=0;
}

else if(str[i-1]=='2')
{
Serial.println("Left");
right();
i=0;
}

else if(str[i-1]=='3')
{
Serial.println("Right");
left();
i=0;
}
THANK
YOU

You might also like