A circle bounding the bottom of the teeth:

a. Addendum circle
b. Addendum cylinder
c. Pitch circle
d. Dedendum circle
Alloy steel known for its resistance to
corrosion, abrasion, and wear that is usually
ideal for mill grinding of ore in cement and
concentrator application. It is usually
combined with molybdenum to increase the
depth hardening.
a. Manganese chromium steel
b. Chromium-moly steel
c. Chorome-nickel-moly steel
d. Manganese-moly steel
A machinery operation whereby the tool
rotates while the feed is stationary.

a. Shaping
b. Milling
c. Turning
d. Reaming
The change in length per unit original length
is

a. Strain
b. Stress
c. Deformation
d. Elastic modulus
An oil storage roof formed to approximately
the surface of a right cone, supported only at
its periphery

a. Self-supporting umbrella roof

b. Self- supporting dome roof
c. Supported cone roof
d. Self-supporting cone roof
An oil storage tank roof formed to
approximately spherical surface, supported
only at its periphery

a. Self-supporting umbrella roof

b. Self-supporting cone roof
c. Self-supporting
d. Supported cone roof
within the elastic limit, the stress is
proportional to strain.

a. Hooke’s law
b. Modulus of elasticity
c. Offset ratio
d. Buckingham’s principle
The length of arc between the two sides of a
gear tooth on the pitch circle

a. Circular thickness
b. Axial plane
c. Helix angle
d. Chordial curves
It refers to any layer or deposit of extraneous
material on the hat transfer surface

a. Low line
b. Pressure drop
c. Fouling
d. Scaling
The ability of material or metal to resist being
crushed is

a. Fatigue strength
b. Bending strength
c. Torsional strength
d. Compressive strength
A type of gear tooth cut inside a cylinder or
ring

a. Rack gear
b. Ring gear
c. Miter gear
d. Internal gear
Test is designed primarily for application to
electric welded tubing for detection of lack of
penetration or overlaps resulting from flash
removal in the weld.
a. Butt weld
b. Paste
c. Lap weld
d. Double butt weld
Milling machine accessories are used to hold
milling cutter in the milling machine

a. Spindle – nose tooling

b. Milling machine cise
c. Vertical milling attachment
d. Milling machine arbors
Have the same thermal and minimum film
thickness limitation as sleeve bearing

a. Ball bearing
b. Roller bearing
c. Thrust bearing
d. Oil bearing
Which tool does not belong to the group?

a. Vice grip
b. Feeler gage
c. Torque wrench
d. Adjustable wrench
Ferrous metals contain a relatively large
amount of

a. manganese
b. carbon
c. sulfur
d. phosphorus
A fillet weld whose size is equal to the
thickness of the thinner joint member

a. Butt joint
b. Butt weld
c. Tack weld
d. Full –fillet weld
The cheapest and the most abundant
engineering material

a. aluminum
b. steel
c. Cast iron
d. babbits
A gear is one in which angle is 90 degrees
that is the pitch cone has become a plane

a. Crown gear
b. Angular gear
c. Miter gear
d. Spiral gear
They are usually the steel or steel casting

a. Mild steel
b. Carbon steel
c. Fire box steel
d. Drop forge dies
Gears used to transmit power between shafts
axis of which it intersect

a. Spur gears
b. Bevel gears
c. Helical gears
d. Straight bevel gears
A corrosion occurs within or adjacent to a
crevice formed by contact with another piece
of the same or another metal:

a. Pitting
b. Galvanic
c. Erosion
d. Crevice
What heat treatment process can cast steel
materials of high chrome, high manganese,
etc. type steel be subjected for the purpose
of machining process?
a. Annealing
b. Tempering
c. Normalizing
d. Quenching
Which of the following is not the work of a
machinist?

a. Reboring
b. Overhauling
c. Grinding
d. Boring
The corrosion of iron or iron-based alloys

a. Rusting
b. Crazing
c. Chalking
d. Fritting
It is used to enable milling machine to take
climb milling cuts

a. Helical driving mechanism

b. Spindle
c. Read out
d. Backlash eliminator
Which of the following metals is non-
magnetic?

a. Manganese steel
b. Cast steel
c. Alloy steel
d. Cast iron
The space between the adjacent teeth

a. tooth
b. flack
c. backlash
d. width
Determine the estimated weight of an A-36
steel plate of size ½ x 4 x 8

a. 280 kg
b. 332 kg
c. 301 kg
d. 297 kg
Steel containing large amounts of mild nickel
and chromium

a. Carbon steel
b. Stainless steel
c. Alloy steel
d. Cat steel
A cylindrical tank with 10 in inside diameter
contains oxygen at 2500 psi. calculate the
required wall thickness in mm under stress of
28,000 psi
a. 11.44 mm
b. 11.34 mm
c. 10.6 mm
d. 10.3 mm
It has molybdenum alloy except

a. SAE 43XX
b. SAE 41XX
c. SAE 6XXX
d. SAE 5XXX
Accident prevention is

a. An association of employers, organization

and individuals
b. The foreman’s responsibility just as much
as production
c. The responsibility of top management
d. A job of a safety director
One important skill that operators of machine
tools must have is an understanding of
measurement which demands

a. speed
b. precision
c. sociability
d. neatness
Test sometimes referred to as an upsetting
test

a. Bend
b. Flaring
c. Flange
d. Crush
The follower reciprocates or oscillates in a
plane perpendicular to the axis of rotation of
the cam.

a. Radial cam
b. Cylindrical cam
c. Cam curves
d. Tangential cam
Strength of a material is that of a stress
intensity determined by considering the
maximum test load to act over the original
area of the test specimen:
a. Yield point
b. Ultimate strength
c. Breaking strength
d. Elastic strength
A machine used in testing steel generally
strike the specimen with an energy from 220
to 265 ft-lb.

a. Izod test
b. Charpy test
c. Rockwell test
d. Test blocks
The total amount of permanent extension of
the gage length measured after the specimen
has fractured and is expressed as percentage
increase of the original gage length

a. Elongation
b. Strain
c. Stress
d. Elastic limit
Which of the following is not part of a lathe
machine?

a. fan
b. carriage
c. headstock
d. tailstock
Which of the following is not a kind of cast
iron?

a. Gray iron
b. White iron
c. Malleable iron
d. Lead iron
Which of the following metal is easy to
chisel?

a. Alloy steel
b. Manganese steel
c. Stainless steel
d. Cast iron
The maximum stress which is reached during
a tension test:

a. Stress
b. Elasticity
c. Strain
d. Tensile strength
Galvanized steel plate is

a. Aluminum
b. Tin
c. Zinc
d. Manganese
A bevel gears of the same size mounted on a
shaft at 90 degrees

a. Crown gears
b. Spur gears
c. Angular gears
d. Miter gears
A weld made to hold the parts of a weldment
in proper alignment until the final welds are
made

a. Butt weld
b. Tack weld
c. Fillet weld
d. Full fillet weld
Commonly utilized/cheapest shaft material
available in the market with carbon content
of 0.28 to 0.34%

a. SAE 4132
b. SAE 4320
c. SAE 1030
d. SAE 4130
A cone formed by elements which are
perpendicular to the elements of the pitch
cone at the large end

a. Cone distance
b. Back cone
c. Root cone
d. Cone center
A weld place in a groove between two
abutting members

a. Full-fillet weld
b. Tack weld
c. Butt weld
d. Fillet weld
The deterioration of organic coating
characterized as completely

a. Chalking
b. Rusting
c. Chocking
d. Fritting
Which of the following is not a classification
of iron ore

a. siderite
b. hermatite
c. sulfurite
d. magnetite
The machine which can flatten surface on a
horizontal, vertical or angular plane is:

a. Drilling machine
b. Shaper machine
c. Power saw
d. Lathe machine
The size of an equal-length fillet weld shall be
based on the length of the largest

a. Isosceles right triangle

b. square
c. Right triangle
d. rectangle
Major component of bronze casting

a. Copper
b. Manganese
c. Zinc
d. Lead
Which of the following is not part of the
headstock?

a. Anvil
b. Spindle
c. Motor
d. Back pressure
Split pulley or pulley made of separate
section bolted together at the rim, the
maximum speed should be limited to about
_____% of the maximum speed of solid pulley

a. 65 to 75%
b. 45 to 50%
c. 55 to 60%
d. 80 to 90%
The shearing strain of a block of metal, 3
inches high is subject to a shearing high force
which distorts the top surface through a
distance of 0.0036 inch.
a. 0.0015 rad
b. 0.008 rad
c. 0.0010 rad
d. 0.0012 rad
Which of the following is the differential of
the shear equation?

a. Bending moment
b. Load of the beam
c. Tensile strength of the beam
d. Slope of the beam
Which of the following materials to be
utilized to reduce cost in the manufacturing
of large worm gears?

a. Alloyed aluminum
b. Bronze rim with cast iron spider
c. Cast iron rim with bronze spider
d. All of the above
The ratio of stress to the corresponding strain
below the proportional limit

a. Stress-strain diagram
b. Gage method
c. Modulus of elasticity
d. Tensile strength
Killed steel is very much associated with

a. manganese
b. sulfur
c. phosphorous
d. silicon
Wheels are sometimes used for the
transmission of high power when an
approximately constant velocity ratio is
desired:
a. Bevel cones
b. Friction gearing
c. Spur friction wheels
d. Evans friction wheels
Gearing in which motion or power that is
transmitted depends upon the friction
between the surfaces in contact

a. Bevel gears
b. Spur friction wheels
c. Evans friction cones
d. Friction gearing
If gears cannot connect parallel shafts, they
are called:

a. Cycloidal gears
b. Helical gears
c. Spur gears
d. Toothed gears
What load P which cause a total deformation
of 0.036 inch of a steel rock which has a cross
section area of 4 in2 and a length of 6 ft.

a. 55,000 lb
b. 40,000 lb
c. 60,000 lb
d. 50,000 lb
A type of welding whereby a wire or powder
from the nozzle of a spray gun is fused by a
gas flame, arc or plasma jet and the molten
particles are projected in a form of a spray by
means of compressed air or gas
a. Electro-slug building
b. Electro-beam welding
c. Plasma-arc welding
d. Metal spray welding
An alloy of tin, copper, antimony, or
sometimes lead:

a. Gold
b. Babbitt
c. Aluminum
d. Cast iron
An iron in which most of the carbon is
chemically combined with the iron:

a. Cast iron
b. Gray iron
c. White iron
d. Malleable iron
A weld of approximately triangular cross
section that join two surfaces at
approximately right angles as in lap joint: tee
joint; corner joint
a. Single welded lap joint
b. Fillet weld
c. Tack weld
d. Butt weld
Determine the number of teeth in a driver of
two spur gears mesh which has a velocity
ratio of 0.75. The driven gear has 36 teeth

a. 50
b. 46
c. 48
d. 26
Major component of bronze casting is:

a. Copper
b. Manganese
c. Zinc
d. Lead
What process does not belong to the group?

a. Brazing
b. Soldering
c. Hardening
d. Resistance welding
The follower reciprocates or oscillates in a
plane parallel to the axis of the rotation:

a. Cam curves
b. Cylindrical cam
c. Tangential cam
d. Radial cam
The ability of metals to stand loads without
breaking down

a. strain
b. stress
c. elasticity
d. strength
An iron has physical properties closely
resembling those of mild steel

a. Malleable cast iron

b. Malleable iron
c. White iron
d. Gray iron
The temperature above which the alloy is
liquid and will run

a. Melting point
b. Fow point
c. Pour point
d. Liquids
SAE steel that responds to heat treatment

a. SAE 1060
b. SAE 1117
c. SAE 1030
d. SAE 1020
Weld-metal impact specimen shall be taken
across the weld with one face substancially
parallel to and within:

a. 3/4 “
b. 1/32”
c. ¼”
d. 1/16”
The unit of deformation is called:

a. Torsion
b. Strain
c. Stress
d. shear
Imparts of reciprocating motion to a single
point cutting tool

a. Dividing head
b. Slotting attachment
c. Circular pitch
d. Circular milling attachment
A test for pipe used for coiling in sizes 2
inches

a. Flaring
b. Crush
c. Flange
d. Bend
The area of the machine shop whose metal is
being melted to form a new shape is the:

a. Foundry area
b. Tool and die
c. Welding area
d. Mass production area
A machine used for the testing of very thin
steel or surface layers

a. Charpy test
b. Izod test
c. Description test
d. Rockwell test
Through how many degrees must an involute
cam turn in order to raise its follower 3 inches
if the diameter of the base circle is 5 inches.

a. 58.7 deg
b. 180 deg
c. 64.4 deg
d. 68.79 deg
A 3” diameter short shaft carrying 2 pulleys
close to the bearings transmit how much
horsepower if the shaft makes 280 rpm

a. 199 hp
b. 198 hp
c. 200 hp
d. 210 hp
It is hardening treatment whereby a cast
metal is being heated to a very high
temperature then suddenly subjected to
rapid cooling to improve hardenability or
wear resistance is called
a. Normalizing
b. Tempering
c. Annealing
d. Quenching
Which of the following elements when large
quantity is harmful to ferrous metal?

a. Sulfur
b. Silicon
c. Zinc
d. Aluminum
Flexible material used to seal pressurized
fluids, normally under dynamic condition

a. Nylon
b. Seal
c. Teflon
d. Packing
To prevent leakage in dynamic seal

a. Gasket
b. Seals
c. Felts
d. Packings
Cast alloy steel for very high temperature
application

a. Manganese-nickel steel casting

b. High chrome steel casting
c. Chrome nickel steel casting
d. High manganese casting
A joint between two overlapping members in
which the overlapped edge of one member is
welded with a fillet weld:

a. A single welded lap joint

b. Double welded lap joint
c. A single lap joint with backing
d. Tack weld
An important accessories of milling machines

a. Milling machine vise

b. Cutters
c. Ram
d. Vertical milling attachment
Split pulley or pulley made of separate
sections bolted together at the rim, the
maximum speed should be limited to about
_____% of the maximum speed of solid pulley.

a. 65 to 75%
b. 45 to 50%
c. 55 to 60%
d. 80 to 90%
Which of the following is not used to temper
steel?

a. Oil bath
b. Brine/salt bath
c. Steam bath
d. Water bath
The path traced by a point moving at a fixed
distance from an axis and with a uniform
motion to the axis and a point moving such a
path:

a. Helical motion
b. Spherical motion
c. Translational
d. Path of a point
The minimum clearance allowed for meshing
spur gears with a circular pitch of 0.1571 and
diametral pitch of 20. the spur gear have 25
teeth
a. 0.007855
b. 0.007558
c. 0.008578
d. 0.007585
The frustums of two cones are used in a
manner to permit a variation of velocity ratio
between two parallel shafts

a. Evans friction cones

b. Bevel cones
c. Spherical cones
d. Friction gearing
Determine the estimated weight of an A-36
steel plates size 3/16” x 6’ x 20’

a. 919 lbs
b. 1012 lbs
c. 829 lbs
d. 735 lbs
Heating of metal above the critical
temperature and then cooling slowly usually
in the furnace to reduce the hardness and
improve the machinability is called

a. Normalizing
b. Annealing
c. Tempering
d. Quenching
Is a form of correction that develop on a
highly localized areas on a metal surfaces

a. Crevice
b. Erosion
c. Galvanic
d. Spitting