Scribd
Upload
554 views20 pages

Industrial Communication Networks

This document discusses three levels of industrial communication networks: enterprise, automation and control, and field device level networks. It also covers topics such as Ethernet/IP, TCP/IP, adapters, cables, connectors, bus, ring, and star topologies, and the uses of routers and switches.

Uploaded by

abdel taib
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
554 views20 pages

Industrial Communication Networks

This document discusses three levels of industrial communication networks: enterprise, automation and control, and field device level networks. It also covers topics such as Ethernet/IP, TCP/IP, adapters, cables, connectors, bus, ring, and star topologies, and the uses of routers and switches.

Uploaded by

abdel taib
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 20

Lesson 2

INDUSTRIAL COMMUNICATION NETWORKS


Industrial Networks

 Classified into three levels based upon the type of data and devices
that use the network.

 Enterprise: non time critical information


 Automation and Control: Real time I/O
 Field device: switches, output devices and drives
Industrial Networks
Enterprise Level

 Shares data between all segments


 Transfers non-time critical data
 Ethernet is preferred network because high speed, open-source protocol and
competitive vendor pool
 In the past proprietary networks have been used, but this do not communicate
with other networks. Ethernet has been implemented to bridge devices from
different networks
Automation and Control Level

 Transfers data between the controller and the I/O devices it controls and to other
controllers
 Data is high urgency – real time
 Determinism: data to be sent and received in a timely manner and verified is
correct
 Reliability 24/7 schedule even in hostile environments
 Security
 Routers typically use to isolate networks and provide security
Field Device Level Networks

 Connects individual I/O devices to a PLC


 Replaces remote I/O racks, adapters, modules, and field wiring with a direct
connection to intelligent switches and output devices
 Ease of installation
 Reduction of I/O wiring
 Error and diagnostic reporting
 Open networks and support different vendors
 Devicenet is the most common field level network for Allen Bradley controllers
(others EtherCat, Serial RS-232, CANopen, etc
ETHERNET TCP/IP
Difference Ethernet/IP and TCP/IP

 TCP is an acronym with stands for Transmission Control Protocol. This protocol
is responsible for managing the connection between a client and a server
 IP has two different meanings depending on how it is used: Industrial Protocol
for Ethernet/IP and Internet Protocol for TCP/IP
 Ethernet/IP uses the Ethernet infrastructure to manage the connection between
various automation devices such as robots, PLCs, sensors, etc. Based on the
Common Industrial Protocol
 TCP/IP industrial protocol used is Modbus TCP/IP which is responsible for the
transmission of the packets. TCP/IP is standard in most programming languages
(C,C++, Matlab). Also Modbus TCP/IP is standard in most PCs.
Ethernet/IP

 Is an offspring of the Common Industrial Protocol CIP


 Developed for transferring data on DeviceNet and ControlNet (Fieldbus)
networks.
 Advantage of speed and reliability of Ethernet.
 Never truly deterministic however good enough for industry
 Real time I/O at 100 Mbps, 20 times faster than ControlNet
 No additional hardware needed to communicate to any Ethernet network.
Adapters

 Connect devices such as controllers, PanelView terminals, drives to other devices


 Provide interface that converts data into a signal that can be transmitted on a cable
and re-convert that signal back into data at destination device
 Make sure devices are Ethernet/IP compatible
Cable

 Cat 5 most common , also known as 10BaseT


 Limited to 100 meters between switches and or routers
 Can be shielded twisted pair (STP) or unshielded (UTP)
 STP thought more expensive than UTP is preferred in areas with high electrical
noise, drives > 10 HP, or conductors carrying >100 amps, and if inside metal
conduit
 Fiber optic run in extreme high electrical noise (immune to noise)
 Fiber optic more expensive and needs converters
 Fiber optic up to 1500 meters between switches
RJ45 Connector Wiring

 Category 5 Ethernet Cable uses 8 wires twisted to form four pair of wires.
 2 standards for arranging the colors in the RJ45 connector, T568A, and T568B
 Cables can be wired straight through or crossover
 Straight through: are used to connect devices to switches and routers
 Crossover: used to directly connect two Ethernet devices together
Crossover cable

 Often use to directly connect a computer to an Ethernet/IP module for initial


setup. The computer runs a software utility called BootP to set the IP address that
the module will use on the network.

 A crossover cable reverses the TX and RX lines from one connector to the other
to permit connecting a PC directly to an Ethernet Device.

 Usually color of cable is red to differentiate


Bus (Backbone) Topology
Ring Topology
Star Topology
Star Topology

 Connects each device through a separate cable or switch, creating segments or


subnets
 Eliminates most message collisions (major factor in stablishing determinism)
 Allow for new nodes to be installed without disrupting existing nodes
 Failure of that node affect only that node
 Reduces network traffic by limiting multicast data from going to all nodes on the
network by sending only to selected nodes
Routers

 Used to connect different devices together while maintaining isolation between


the networks.

 Only messages with the correct address can cross the router from one network to
another
Switches

 Intelligent Ethernet switches have replace hubs to reduce the number of message
collisions in the network
 Collision occur frequently because more than one node tries to transmit at the
same time
 Ethernet switch knows the address of each device on each port and stores address
in memory. When a message is received, the switch decodes the destination
address and sends the message only to the port of which the device is connected
 ControlLogix inputs mulitcasts to every node in the network. Intelligent switches
can control multicast data, such as I/O to prevent overloading the network with
messages
This work is licensed under the Creative Commons Attribution 4.0 International License.
To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.

This workforce solution was funded by a grant awarded by the U.S. Department of Labor’s Employment and
Training Administration. The solution was created by the grantee and does not necessarily reflect the official
position of the U.S. Department of Labor. The Department of Labor makes no guarantees, warranties, or
assurances of any kind, express or implied, with respect to such information, including any information on linked
sites and including, but not limited to, accuracy of the information or its completeness, timelines, usefu lness,
adequacy, continued availability, or ownership.

You might also like