Control Systems

Lect.7 Steady State Error

Basil Hamed
Chapter Learning Outcomes
  completing this chapter the student will be able to:
After
• Find the for a unity feedback system (Sections 7.1-7.2)
• Specify a system's performance (Section 7.3)
• Design the gain of a closed-loop system to meet specification
(Section 7.4)
• Find the for disturbance inputs (Section 7.5)
• Find the for nonunity feedback systems (Section 7.6)
• Find the sensitivity to parameter changes (Section 7.7)
• Find for systems represented in state space (Section 7.8)

Basil Hamed 2
7.1 Introduction
In Chapter 1, we saw that control systems analysis and design
focus on three specifications:
(1) Transient Response (Chapter 4)
(2) Stability (Chapter 6)
(3) Steady-State Errors (Chapter 7)

Now we are ready to examine steady-state errors. We define the

errors and derive methods of controlling them.

Basil Hamed 3
Definition and Test Inputs
 
Steady-state error is the difference between the input and the output
for a prescribed test input as Test inputs used for steady-state error
analysis and design are summarized in Table below.

Basil Hamed 4
 Application to Stable Systems
• Since
  we are concerned with the difference between the
input and the output of a feedback control system after the
steady state has been reached, our discussion is limited to
stable systems, where the natural response approaches zero
as .

• Unstable systems represent loss of control in the steady state

and are not acceptable for use at all.

• Thus, the engineer must check the system for stability while
performing steady-state error analysis and design.

Basil Hamed 5
SS Error for Unit Step Input

Basil Hamed 6
 7.2 Steady-State Error for Unity
Feedback Systems
Steady-state error can be calculated from a system's closed-loop
transfer function, T(s), or the open-loop transfer function, G(s),
for unity feedback systems.
Steady-State Error in Terms of T(s)

  To find we need to Apply the final value theorem

Basil Hamed 7
Example 7.1 P 345
 
PROBLEM: Find the steady-state error for and the input is a
unit step.
SOLUTION: From the problem statement, R(s) = 1/s ,

Since T(s) is stable and, subsequently, E(s) does not have right-half-
plane poles or jw poles other than at the origin, we can apply the final
value theorem
  e( = 1/2.

Basil Hamed 8
 Steady-State Error in Terms of G(s)
E(s)= R(s)- C(s); C(s) =G(s) E(s)

We now apply the final value theorem

Basil Hamed 9
 Test Signals

The three test signals we use to establish specifications for a

control system's steady-state error characteristics are :
1. Step
2. Ramp
3. Parabola
Let us take each input and evaluate its effect on the steady-state
error by using Eq.

Basil Hamed 10
 Test Signals
Step Input
Using Eq. With R(s) = 1/s, we find

 Ramp Input Using above Eq. with, R(s) = , we obtain

Basil Hamed 11
 Test Signals

 
Parabolic Input Using Eq. with R(s) = , we obtain

Basil Hamed 12
Example 7.2 P. 347
 
PROBLEM: Find the steady-state errors for inputs of 5u(t),
5tu(t), and 5u(t) to the system shown in Figure below. The
function u(t) is the unit step.

Basil Hamed 13
Example 7.2 P. 347
 
SOLUTION: First we verify that the closed-loop system is
indeed stable.

i) 5 u(t);

ii) 5tu(t)

iii) 5u(t)

Basil Hamed 14
Example 7.3 P 348
 
PROBLEM: Find the steady-state errors for inputs of 5u(t),
5tu(t), and 5u(t) to the system shown in Figure below. The
function u(t) is the unit step.

Basil Hamed 15
Example 7.3 P 348
 
SOLUTION: First verify that the closed-loop system is indeed
stable.

i) 5 u(t);

ii) 5tu(t)

iii) 5u(t)

Basil Hamed 16
 7.3 Static Error Constants and
System Type

We continue our focus on unity negative feedback systems

and define parameters that we can use as steady-state error
performance specifications. These steady-state error
performance specifications are called static error constants.

Basil Hamed 17
 Static Error Constants

For a step input, u(t),

  :position constant

  1
𝑒 ( ∞ )= 𝑒𝑠𝑡𝑒𝑝 =
1+𝑘 𝑃

For Ramp input, tu(t),

  :velocity constant

  1
𝑒 ( ∞ )= 𝑒𝑟𝑎𝑚𝑝 =
𝑘𝑣
Basil Hamed 18
 Static Error Constants

For  a parabolic input, .

  :accelration constant

  1
𝑒 ( ∞ ) = 𝑒 𝑝𝑎𝑟𝑎𝑏𝑜𝑙𝑎 =
𝑘𝑎

Basil Hamed 19
Example 7.4 P 350
PROBLEM: For each system in the Figure below , evaluate the static
error constants and find the expected error for the standard step, ramp,
and parabolic inputs.

Basil Hamed 20
Example 7.4 P 350
SOLUTION: First verify that all closed-loop systems shown are
indeed stable.
a)

21
Basil Hamed
Example 7.4 P 350
b)

Basil Hamed 22
Example 7.4 P 350
C)

Basil Hamed 23
 System Type
The values of the static error constants,, depend upon the form of G(s),
especially the number of pure integrations in the forward path. Since
steady-state errors are dependent upon the number of integrations in the
forward path.
we define system type to be the value of n in the denominator or,
equivalently, the number of pure integrations in the forward path.

Therefore, a system with n = 0 is a Type 0 system. If n = 1 or n = 2,

the corresponding system is a Type 1 or Type 2 system, respectively.
Basil Hamed 24
Example

Type 1

Type 2

Type 3

Basil Hamed 25
Relationships between input and system type

Type Step Input Ramp Input Parabola Input

0

1
1 0
0

2 0 0
2 0 0
3 0 0 0

3 0 0 0

Basil Hamed 26
Example
 Find for given system , with inputs
step, ramp, parabola

The closed loop -11.6063

poles are -0.1968 + 0.6261i
-0.1968 - 0.6261i

Solution: The system is stable and of type 2

Zero SS error for step and ramp input

For parabolic input

Basil Hamed 27
7.4 Steady-State Error Specifications
Static error constants can be used to specify the steady-state error
characteristics of control systems. Just as damping ratio, ζ, settling
time, Ts, peak time, Tp, and percent overshoot, % OS, are used as
specifications for a control system's transient response, so the
position constant, Kp, velocity constant, Kv, and acceleration
constant, Ka, can be used as specifications for a control system's
steady-state errors.
For example, if a control system has the specification Kv = 1000, we
can draw several conclusions:
1. The system is stable 2. The system is of Type 1
  is
3. A ramp input is the test signal.

Basil Hamed 28
Example 7.5 P. 354
PROBLEM: What information is contained in the specification
Kp = 1000?

SOLUTION: The system is stable. The system is Type 0, since

only a Type 0 system has a finite Kp. Type 1 and Type 2
systems have Kp = ∞ . The input test signal is a step, since Kp
is specified. Finally, the error per unit step is

Basil Hamed 29
 Example 7.6 P 355
PROBLEM: Given the control system in Figure, find the value of
K so that there is 10% error in the steady state.

SOLUTION: Since the system is Type 1, the error stated in the

problem must apply to a ramp input; only a ramp yields a finite error
in a Type 1 system. Thus,

k= 672
Basil Hamed 30
7.5 Steady-State Error for Disturbances
Feedback control systems are used to compensate for
disturbances or unwanted inputs that enter a system. The
advantage of using feedback is that regardless of these
disturbances, the system can be designed to follow the input
with small or zero error.

Basil Hamed 31
 7.5 for Disturbances
1

But
2

Substituting Eq. (2) into Eq. (1) and solving for E(s), we obtain

To find the steady-state value of the error, we apply the final value theorem 3 to Eq. (3)
and obtain

Basil Hamed 32
 Example 7.7 P.357
 
PROBLEM: Find the component due to a step disturbance for the
system shown.

SOLUTION: The system is stable.

The steady-state error component due
to a step disturbance is found to be

Basil Hamed 33
7.6 Steady-State Error for Nonunity
Feedback Systems
Control systems often do not have unity feedback because of the
compensation used to improve performance or because of the physical
model for the system.

Basil Hamed 34
 Example 7.8 P. 359
PROBLEM: For the system shown, find the system type, the
appropriate error constant associated with the system type, and the
steady-state error for a unit step input. Assume input and output units
are the same.

SOLUTION: After determining that the system is indeed stable, one may
impulsively declare the system to be Type 1. This may not be the case,
since there is a nonunity feedback element,
The first step in solving the problem is to convert the system into an
equivalent unity feedback system.
Basil Hamed 35
 Example 7.8 P. 359

we find

Thus, the system is Type 0, since there are no pure integrations in above
Eq. The appropriate static error constant is then Kp, whose value is

The steady-state error, e(∞) is

Basil Hamed 36
 7.7 Sensitivity
• During the design process, the engineer may want to consider
the extent to which changes in system parameters affect the
behavior of a system.
• Ideally, parameter changes due to heat or other causes should
not appreciably affect a system's performance.
• The degree to which changes in system parameters affect
system transfer functions, and hence performance, is called
sensitivity.
• A system with zero sensitivity (that is, changes in the system
parameters have no effect on the transfer function) is ideal.

Basil Hamed 37
 7.7 Sensitivity
For example, assume the function F = K/(K + a)
If K = 10 and a = 100, then F = 0.091.
If parameter a triples to 300, then F = 0.032.
We see that a fractional change in parameter
a of (300 — 100)/100 = 2 (a 200% change),
yields a change in the function
F of (0.032 - 0.091)/0.091 = -0.65 (-65% change).
Thus, the function F has reduced sensitivity to changes in
parameters.

Basil Hamed 38
 7.7 Sensitivity
Sensitivity is the ratio of the fractional change in the function
to the fractional change in the parameter as the fractional
change of the parameter approaches zero. That is,

which reduces to

Basil Hamed 39
 Example 7.10 P. 362
PROBLEM: Given the system shown, calculate the sensitivity of the
closed-loop transfer function to changes in the parameter a. How
would you reduce the sensitivity?

SOLUTION: The closed-

loop transfer function is

which is, in part, a function of the value of s. For any value of s, however,
an increase in K reduces the sensitivity of the closed-loop transfer function
to changes in the parameter a.
Basil Hamed 40
Example 7.11 P. 363
PROBLEM: For the system shown, find the sensitivity of the steady-
state error to changes in parameter K and parameter a with ramp inputs.

SOLUTION: The steady-state error

for the system is
 Thesensitivity of e() to
changes in parameter a is
 Thesensitivity of e() to
changes in parameter K is
 Thus,changes in either parameter a or parameter K are directly reflected
in e() and there is no reduction or increase in sensitivity.
The negative sign, indicates a decrease in e() for an increase in K.
Basil Hamed 41
7.8 Steady-State Error for Systems in
State Space

• Up to this point, we have evaluated the steady-state error

for systems modeled as transfer functions.

• In this section, we will discuss how to evaluate the steady-

state error for systems represented in state space (analysis
via final value theorem)

Basil Hamed 42
 Analysis via Final Value Theorem
A single-input, single-output system represented in state space
can be analyzed for steady-state error using the final value
theorem and the closed-loop transfer
Consider the closed-loop system represented in state space:

The Laplace transform of the error is

where T(s) is the closed-loop transfer function, we obtain

Applying the final

value theorem, we have
Basil Hamed 43
Example 7.13 P. 365
PROBLEM: Evaluate the steady-state error for the system shown
for unit step and unit ramp inputs. Use the final value theorem.

SOLUTION:

 For a unit step, R(s) = 1/s, and e() = 4/5. For a unit ramp, R(s) = 1/, and
e() = . Notice that the system behaves like a Type 0 system

Basil Hamed 44