Scribd
Upload
28 views

Lecture 34 - Design of Two-Way Floor Slab System: April 12, 2001 CVEN 444

The document discusses the design of two-way floor slab systems, including calculating minimum slab thickness, shear strength of slabs with and without beams, and shear reinforcement methods. It provides an example of determining required slab thickness and shear reinforcement for an interior panel with given load, material properties, and geometry. Design considerations include checking shear strength of concrete and adding reinforcement if needed based on ACI code provisions.

Uploaded by

Ahmed Ewis
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
28 views

Lecture 34 - Design of Two-Way Floor Slab System: April 12, 2001 CVEN 444

The document discusses the design of two-way floor slab systems, including calculating minimum slab thickness, shear strength of slabs with and without beams, and shear reinforcement methods. It provides an example of determining required slab thickness and shear reinforcement for an interior panel with given load, material properties, and geometry. Design considerations include checking shear strength of concrete and adding reinforcement if needed based on ACI code provisions.

Uploaded by

Ahmed Ewis
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 22

Lecture 34 - Design of Two-Way

Floor Slab System


April 12, 2001
CVEN 444
Lecture Goals
• Thickness Example
• Shear Strength of Slabs
• Shear Example
• Direct Design Method
Example

The floor system consists of solid


slabs and beams in two directions
supported on 20 in. square columns.
Determine the minimum slab
thickness required for an interior
panel. Use fc = 4 ksi and fy = 60 ksi
Example

The cross-sections are:


Example

The resulting cross section:


Shear Strength of Slabs
In two-way floor systems, the slab must have adequate
thickness to resist both bending moments and shear
forces at critical section. There are three cases to look at
for shear.
1. Two-way Slabs supported on beams
2. Two-Way Slabs without beams
3. Shear Reinforcement in two-way slabs
without beams.
Shear Strength of Slabs
Two-way slabs supported on beams

The critical location is found at d distance from the


column, where


 Vc   2 f c bd 
The supporting beams are stiff and are capable of
transmitting floor loads to the columns.
Shear Strength of Slabs
The shear force is calculated using the triangular and
trapezoidal areas. If no shear reinforcement is provided,
the shear force at a distance d from the beam must equal


Vud   Vc   2 f c bd 
where,
 l2 
Vud  wu   d 
 
2 
Shear Strength of Slabs
Two-Way Slabs without beams

There are two types of shear that need to be addressed


1. One-way shear or beam shear at distance d
from the column
2. Two-way or punch out shear which occurs
along a truncated cone.
Shear Strength of Slabs

1. One-way shear or beam shear at distance d from


the column
2. Two-way or punch out shear which occurs along a
truncated cone.
Shear Strength of Slabs

One-way shear considers critical section a distance d


from the column and the slab is considered as a wide
beam spanning between supports.


Vud   Vc   2 f c bd 
Shear Strength of Slabs
Two-way shear fails along a a truncated cone or pyramid
around the column. The critical section is located d/2 from
the column face, column capital, or drop panel.
Shear Strength of Slabs
If shear reinforcement is not provided, the shear strength
of concrete is the smaller of:
 
 4 

Vc    2   f c bo d   4 f c bo d 
 c 

bo = perimeter of the critical section


c = ratio of long side of column to short side
Shear Strength of Slabs
If shear reinforcement is not provided, the shear
strength of concrete is the smaller of:

 d 

Vc    s 
 2 f c bo d

 bo 
s is 40 for interior columns, 30 for edge
columns, and 20 for corner columns.
Shear Strength of Slabs
Shear Reinforcement in two-way slabs without beams.
For plates and flat slabs, which do not meet the condition
for shear, one can either

- Increase slab thickness


- Add reinforcement

Reinforcement can be done by shearheads, anchor bars,


conventional stirrup cages and studded steel strips.
Shear Strength of Slabs
Shearhead consists of steel I-beams or channel welded
into four cross arms to be placed in slab above
a column. Does not apply to external columns
due to lateral loads and torsion.
Shear Strength of Slabs
Anchor bars consists of steel reinforcement rods or
bent bar reinforcement
Shear Strength of Slabs
Conventional stirrup cages
Shear Strength of Slabs
Studded steel strips
Shear Strength of Slabs
The reinforced slab follows section 11.12.4 in the
ACI Code, where Vn can not
Vc  4 f c bo d
Vn  Vc  Vs  6 f c bo d Av f y d
Vs 
The spacing, s, can not exceed d/2. s
If a shearhead reinforcement is provided

Vn  7 f c bo d
Example Problem
Determine the shear
reinforcement required for an
interior flat panel considering
the following: Vu= 195k, slab
thickness = 9 in., d = 7.5 in.,
fc = 3 ksi, fy= 60 ksi, and
column is 20 x 20 in.
Example Problem
The final result:
13 stirrups at total
distance of 45.5 in

You might also like