Scribd
Upload
44 views

A Project Progress Report On " ".: Design and Development of Multi-Tasking Cutting Machine

This report summarizes a project to design and develop a multi-tasking cutting machine. The machine is intended for small industries and allows multiple cutting operations to be performed simultaneously, improving productivity. Main components include a frame, bevel gears, scotch yoke mechanism, drilling tool, DC motor, and hacksaw blade. A scotch yoke mechanism converts rotational to reciprocating motion. Bevel gears transmit power between perpendicular shafts. The machine can perform operations like drilling, grinding, and shaping. Progress made includes designing the frame and transmission systems. Testing will continue to refine the design.

Uploaded by

prabhat kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
44 views

A Project Progress Report On " ".: Design and Development of Multi-Tasking Cutting Machine

This report summarizes a project to design and develop a multi-tasking cutting machine. The machine is intended for small industries and allows multiple cutting operations to be performed simultaneously, improving productivity. Main components include a frame, bevel gears, scotch yoke mechanism, drilling tool, DC motor, and hacksaw blade. A scotch yoke mechanism converts rotational to reciprocating motion. Bevel gears transmit power between perpendicular shafts. The machine can perform operations like drilling, grinding, and shaping. Progress made includes designing the frame and transmission systems. Testing will continue to refine the design.

Uploaded by

prabhat kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 13

SANT LONGOWAL INSTITUTE OF

ENGINEERING AND
TECHNOLOGY
A project progress report on “Design and
development of multi-tasking cutting
machine”.

Presented by-
HARWINDER SINGH ( GME /1731711)
RAJWINDER SINGH (GME/ 1731722)
BIKRAM SINGH (GME/ 1731723)
ANKUSH KAUSHIK (GME/1731726)
DESIGN AND DEVELOPMENT OF MULTITASKING CUTTING MACHINE

INTRODUCTION:-
multitasking cutting machine is a machine that is made especially for the small
scale industries where labours working are have very little technology.
This is a machine that performs the work quickly and efficiently without the
hassle of using different machines for performing different cutting operations
on the workpiece.
Every industry desires to make high productive rate maintain the quality and
standard of the product at low average cost, in ana industry consideration
portion of investment is being made for machinery installation. So in this
project we are working on a machine which can perform various operations
simultaneously and it helps to save the man power and helps to increase
production rate.
Main components:-

FRAME
BEVEL GEAR
SCOTCH YOKE MECHANISM
DRILLING TOOL
DC MOTOR
HACKSAW BLADE
DRILLING CHUCK
SCOTCH YOKE MECHANISM
The scotch yoke is a reciprocating motion mechanism,
converting the linear motion of a slider into a rotational motion
or vice-versa. The reciprocating part is directly coupled to a
sliding yoke with slot that engages a pin on the reciprocating
part, the location of the piston versus time is a sine wave of
constant amplitude, and constant frequency given a constant
rotational speed.
BEVEL GEARS
A bevel gear is shaped like a right circular cone with most of its
tip cut off. When two bevel gear mesh, their imaginary vertices
must occupy the same point. Their shaft axes also intersect at
this point, forming an arbitrary non-straight angle between the
shafts. The angle between the shaft can be anything except zero
or 180 degrees.
OPERATION PERFORMED BY THE
MACHINE

Drilling
Grinding
Shaping
METHODOLOGY
In this project we generally give power supply to the shaft on which a bevel gear
is mounted on it and a second bevel gear at a right angle to it has been mounted
on a drill shaft to which a drill bit is being attached. At one end of the shaft is
connected to power supply other end is being joined to a circular disc, through
this disc scotch yoke mechanism is being performed (rotator y motion is
converted into reciprocating motion). Also between in these two a helical gear is
mounted which transfer its motion to other helical gears which is mounted on a
shaft consisting of a grinding wheel.

EXPERIMENTAL SETUP-
In this conceptual model we have involved the gear arrangement for power
transmission at different working centres basically gear and cogwheel is a
rotating machine part having cut teeth or cogs, which mesh with another toothed
part in order to transmit torque, in most cases with teeth on the one gear being of
identical shape and often also with that shape on the other gear.
Two or more gears working In tandem are called a transmission and can produce a
mechanical advantage through a gear ratio and thus may be considered as a
simple machine.
PROJECT PLANNING AND
EXECUTION
The project is planned in the following manner-

• Identification of the problem


• Literature review and details collection
• Selection of transmission system
• Break the task into elements
• Design and final drawing of components
• Manufacturing of frame
• Transmission
• Testing and modifications required
PROGRESS-
• Identification of problem is done.
• We made the design and the drawing of the machine frame.
• We made the estimate of the project.
• We are also start buying the different parts of the machine and
start working on the project.
COST ESTIMATION
Cost incurred during the project work is the sum of the various
cost the expenditure on the manufactured items is calculated as
sum of material and cost of processing.
Mfg.cost = cost of material + cost of processing
processing cost = rate of processing * processing time
cost of material = rate of material in Rs/kg * material kg
ADVANTAGES
• Multi-operations can be performed at one time.
• Our machine is used in return stroke mechanism also.
• All operations are performed on a single motor.
• Size is compact so it requires less space.
• Time saving
• Less man power is required
• Low manufacturing and maintenance cost.
APPLICATIONS

• It can be used in mini woorkshops.


• For cutting of wooden material.
• For grinding the material.
.

THANK YOU.

You might also like