SEPAM 1000 +

Sepam 1000+
~ Systim Electrical protection
Automatision Monitoring
1000 plus
~ 1000 : jenis sepam 1000
~ Plus : bisa komunikasi ( integrasi )
~ Auto : bisa dikendalikan dari sistim
SCADA ( jarak jauh/DCS )
MACAM – MACAM SEPAM 1000 +
Series 20
~ S 20 (subtation)
~ T 20 ( trafo )
~ M 20 ( motor )
~ B 21 ( busbar)
~ B 22 ( busbar )

Series 40
~ S 40 / S 41 / S 42 type
~ T 40 / T 42 type
~ M 41 type
SEPAM 1000+

Series 20
~ Tidak ada capasitor sehingga tidak bisa memori alarm/
kejadian apabila suply tegangan dimatikan tetapi setting
reley masih tetap

~ Memori alarm sampai 16 kejadian ( disply )

~ Memori alarm sampai 64 kejadian (soft wire/SFT)

SEPAM 1000+

Series 40
~ Ada capasitor sehingga bisa memori alarm/kejadian bila
suply tegangan dimatikan dan kemampuannya 24 jam

~ Memori alam sampai 16 kejadian (disply)

~ Memori alarm sampai 128 kejadian ( sft)

~ Accurasi pengukuran kira-kira 1 persen

APPLICATION SERIES 20

Type S 20
~ Substation incomer dan feeder
~ Fungsi protections
+ 50/51 , phase overcurrent
+ 50N/51N , earth fault
+ 46 , negative sequence/unbalance
~ Logig discriminan ( modul MES 108/MES 114 )
~ 4 recloser ( blocking rele atasnya )
APPLICATION SERIES 20

Type T 20

~ Pritection functions
+ 50/51 , phase overcurrent
+ 50N/51N , earth fault
+ 46 , unbalance
+ 49RMS , thermal overload
+ 38/49T ,temperatur monitoring ( MET 148 )

~ dapat mendeteksi trafo ( bucholz/thermostat) dengan

menggunakan
modul (MES 108/MES 114)
APPLICATION SERIES 20

Type M 20
~ protection functions
+50/51, 50N/51N, 46
+49RMS, 38/49T
+37, phase undercurrent
+48/51LR,Starting time dan locked rotor
+66, starts per hour
APPLICATION SERIES 20

Type B 21/B 22
~ Fungsi proteksi tegangan
+27/59, phase to phase under/over voltage
+81L/81H, under/over frequens
+59N, pergeseran tegangan pada titik netral
+27D/47, positive sequence under voltage
+27S, phase to phase under voltage
~ Type B21 tanpa 81R
~ Type B22 ada 81R/ROCOF (pendeteksi kecepatan freq)
APPLICATION SERIES 40

Type S40/41/42
~ Fungsi proteksi
+ 50/51,50N/51N,46,50BF
+ 67N/67NC, relay arah gangguan terhadap tanah
+ 67, relay arah gangguan phase to phase
+ 32P, revers power (daya kembali)

~ Mengukur tegangan,arus,daya dan energi

APPLICATION SERIES 40

Type T40/42
~ Fungsi proteksi
+ 50/51,50N/51N,46,50BF
+ 67N/67NC, relay arah gangguan terhadap tanah
+ 67, relay arah gangguan phase to phase
+ 32P, revers power (daya kembali)
+ 49RMS, 38/49T (temperatur)
~ Mengukur tegangan,arus,daya dan energi
APPLICATION SERIES 40

Type M41
~ Fungsi proteksi
+ 50/51,50N/51N,46,50BF
+ 67N/67NC, relay arah gangguan terhadap tanah
+ 67, relay arah gangguan phase to phase
+ 32P, revers power (daya kembali)
+ semua proteksi yang ada di Type M20

~ Mengukur tegangan,arus,daya dan energi

SEPAM 1000+

UMI (USER MACHINE INTERFACES)

1. Basic Umi
~ metering local dan cara mengoperasikan harus
menggunakan SFT 2841

2. Advances Umi
~ metering lokal,dapat mengoperasikan dari lokal
dan bisa menggunakan SFT 2841

3. Remote Advance Umi

~ menambah fesilitas instal,tidak bisa instal dari
Sepam
SEPAM 1000+

SFT 2841
~ peralatan yang digunakan untuk menset parameter,
fungsi proteksi.Dilengkapi dengan hystori alarm, ge-
lombang recording dan memberikan data parameter
dan penerima data.

Logig Input/Output
~ standart output 4 logig output
~ MES 108 ( 4 logig input,4 logig output )
~ MES 114 ( 10 logig input,4 logig output )
SEPAM 1000+
Sepam 1000+
~ mudah cara menginstal
~ bermacam-macam perlengkapan sepam
~ dapat digabung dengan jarak kurang lebih 100 mm
Suply tegangan
~ 48v-250v dc,110v-240v ac,24v dc
~ logig input : 24v-250v dc
~ terminal yang membedakan dan tahan radiasi
~ input/output modul tidak gandeng
~ temperatur -25 c- 70 c bisa bekerja
SEPAM 1000+

BASE UNIT

~ base unit baru

~ tiga terminal tegangan dari trafo tegangan
~ tiga terminal arus dari trafo arus
~ sama ukurannya antara series 20 dan series 40
~ konsumsi daya kurang dari 15 watt
 CHARACTRISTICS SEPAM 1000+

• DIGUNAKAN SESUI DENGAN FUNGSINYA

TRIPPING THRESHOLD
TIME DELAYED
MEMORI TIME

FUNGSI SPECIAL PROTEKSI

PICK UP / DROP OUT
INSTATANIUS TRIPPING
MEMORI KALAU ADA GANGGUAN
RECOVERY TIME ( RESET )
 CHARACTRISTICS SEPAM 1000+

2 CHARACTRISTICS TIME DELAYED TRIPPING

~ DT. DEFINIT TIME ( CONSTANTANIUS )

~ IDMT. INVERS DEFINIT MINIMUM TIME

STANDART

~ IEC
~ ANSI
~ IAC
 CHARACTRISTICS SEPAM 1000+

CHARACTRISTIC TIME DELAYED

~ IEC IDMT CURVE

K T
PERSAMAANNYA : Td =
X ß
@
( I/Is ) - 1

CURVE K @ ß

SIT 0,14 0,02 2,97

VIT 13,5 1 1,5
LIT 120 1 13,3
EIT 80 2 0,8
UIT 315,2 2,5 1,0
 CHARACTRISTICS SEPAM 1000+

• IEEE IDMT curve:

PERSAMAANNYA : Td = A + B X T

@
( I/Is ) – 1 ß
CURVE A B @ ß

Mod Inv. 0,0103 0,0228 0,02 0,2414

Verry Inv. 3,922 0,0982 2 0,1378
Extre.Inv. 5,64 0,0243 2 0,0813
 CHARACTRISTICS SEPAM 1000+

• IAC IDMT curve

persamaannya : Td = A+ B + D + E T
2 3 ß
(I/Is – C) (I/Is –C) (I/Is – C)

CURVE A B C D E

IAC Inv. 0,2078 0,8630 0,8000 -0,4180 0,1947

Verry Inv. 0,0900 0,7955 0,1000 -1,2885 7,9586
Extrem Inv. 0,0040 0,6379 0,6200 -1,7872 0,2461
 CHARACTRISTICS SEPAM 1000+

• CURVE DEFINIT TIME

t

Operation zone

I/Is
Is I

Is : 0perating current threshold

T : pritection operating delay (constan)
 CHARACTRISTICS SEPAM 1000 +

• INVERS DEFINIT MINIMUM TIME CURVE

t
Operation zone

I/Is
I 1,2 10 20 I

Is : OPERATING CURRENT THRESHOLD

T : PROTECTION OPERATION DELAY , I = 10XIs
 CHARACTRISTICS SEPAM 1000+
• TMS : Time Multiplier Setting TMS = 1 , T = 2,97s

TMS = 0,337 , T = 1 s
t
IEC SIT curve TMS = T/2,97

IEC VITcurve TMS = T/1,5

2,97
IEC EIT curve TMS = T/0,808
1
IEC LIT curve TMS = T/13,33
I/Is
10

Example for IEC SIT

 SEPAM 1000 +

• PROTECTION 50/51(overcurrent)
I set point
~ Definit Time 0,1In – 24In
~ IDMT 0,1In – 2,4In

Time delay
~ Definit Time Inst. 50 ms – 300 ms
~ IDMT 100 ms – 12,5 s/TMS
Accuracy ± 5%
Bila terjadi trip Display muncul “ PHASE FAULT “
 SEPAM 1000 +

• PROTECTION 50N/51N (Earth O C)

I set point
Definit Time – SUM 3I 0,1In – 15In
- sensor CSH
2A rating 0,2 A - 30 A
5A rating 0,5 A - 75 A
20A rating 2 A - 300 A
 SEPAM 1000 +
• PROTECTION 50N/51N (Earth O C)
• IDMT Time
SUM 3I - 0,1In – In
Sensor CSH
2A rating 0,2A - 2A
5A rating 0,5A - 7,5A
20A rating 2A - 20A
T set Definit Time Inst. 50ms - 300s
IDMT Time 100ms - 12,5s

# Bila Trip Display akan muncul “ EARTH FAULT”

 SEPAM 1000 +

• PROTETECTION 46 (Unbalance)
• I set point
Definit Time 10% Ib - 500% Ib
IDMT Time 10% Ib - 50% Ib
Schneider IDMT 10% Ib - 50% Ib
Time Delay
Definit 100ms - 300ms
IDMT 100ms - 1s

# Bila Trip Display muncul “ UNBALANCE “

 SEPAM 1000 +

• PROTECTION 49RMS (Thermal O Load)

• Set Point
Es1 Alarm set point 50% - 300%
Es2 Tripping set point 50% - 300%
Time Delay
T1 (Heat rise) 1mn - 600mn
T2 (Cooling) 5mn - 600mn
Accuracy ± 2%
# Bila Heating mencapai Es1,display muncul “ALARM
THERMAL” dan bila mencapai Es2 akan muncul “THERMAL
OVERLOAD” dan diikuti dg alarm “START INHIBIT”
 SEPAM 1000 +

• PROTECTION 37 (UNDERCURRENT)
I set pont 15% - 100%
Accuracy ± 5%

Time Delay 50ms - 300ms

Accuracy ± 2%

# Bila terjadi Trip display akan muncul “UNDER

CURRENT”
 SEPAM 1000 +

• PROTECTION 48-51LR (Excessive start time,Locked

Rotor)
I set point 50%Ib - 500%Ib
Accuracy ± 5%

Time delay ST 500ms - 300s ( LONG START)

LT 50ms - 300s ( BLOCK ROTOR)
LTS 50ms - 300s
Accuracy ± 2% ( 25ms)
 SEPAM 1000 +

PROTECTION 66 (Start perhour)

~ Start yg sering akan menimbulkan panas yg berlebihan
dan menyebabkan kerusakan pada Winding Motor
Setting point : Pereode 1 - 6 Hour
Nb of start 1 - 60X
Nb of hot start 1 - Nb of start
Nb of cool start 1 - Nb of start
Time Delay stop/start 0mn - 90mn
# Bila Trip,display akan muncul “ START INHIBIT”
 SEPAM 1000 +

PROTECTION 27/27S (Undervoltage)

Set point Us/Vs 5%Uns/Vns - 100%Uns/Vns
Accuracy ± 2%

Time Delay 50ms - 300s

Accuracy ± 2% (25ms)

# Bila Trip, display akan muncul “UNDERVOLTAGE”

 SEPAM 1000 +

• PROTECTION 59 (Overvoltage)
• Us/Vs set point 50%Uns/Vns-150%Uns/Vns
Accuracy ± 2%

Time Delay 50ms - 300s

Accuracy ± 2%

# Bila Trip,display muncul “OVERVOLTAGE”