<REFERENCE ｆor SURVEY/DESIGN,

WORK IMPLEMENTATION>

Copyright©Fujikura Ltd./K.A Page 1 Guide book for FTTH-Premise v 1.0 May 2014)
 8/12/24c SSW

8/12/24c SCPT

Figure 1. Network topology

8/12/24c SCPT

Figure 2. Drop Point for pole mount

Copyright©Fujikura Ltd./K.A Page 2 Guide book for FTTH-Premise v 1.0 May 2014)
 Materials for FTTH OSP (STO - ODP)
Distribution Cable
ODP (Wall Mount)
(Aerial)
Note (*1): See Note (*1)
ODP-CA-8/16
For Aerial locations under SP#2 AC-OF-SM-8/12/24-SC
and after, intermediate ODPs ODP (Aerial)
may not be installed unless there
is an immediate demand. ODP-SSW-8
Branching ODP 1) ODP-SSW-8: To be installed (1:8 Splitter built-in)
(Pole/Wall Mount) at every end point including
the branching section.
ODP-PW-BR 2) ODP-PW-BR: To be installed
at the branching point and the
end point where future Line Guard/
extension is expected.
Suspension
Branching ODP Ring Clamp
(Pedestal)
C-Clamp
ODP-PL-BR
ODP (Pedestal)

ODP-PL-8/16 Branching ODP

ODC (Pole/Wall Mount)
ODC
ODC-C-48/144/288 Splitter ODP-PW-BR
Note: ODC-C-48 = Wall mount Type
Passive Splitter

PS-1-2-ODC/ PS-1-8-ODP
PS-1-4-ODC

Distribution Cable
(Duct)
STO
Jointing Closure Type/Designator
DC-OF-SM-8/12/24-SC
for 12c-24c SC-OF-SM-24

for 12c-48c SC-OF-SM-48

Feeder Cable for 12c-96c SC-OF-SM-96

OTB
DC-OF-SM- for 12c-144c SC-OF-SM-144
TC-OF-SM- 12D/24D/48D/
12/24/48/72/96/144 96D/144D/288D for 12c-288c SC-OF-SM-288

Copyright©Fujikura Ltd./K.A Page 3 Guide book for FTTH-Premise v 1.0 May 2014)
 Materials for FTTH-OSP (HRB: High-Rise Building)
ODP-HRB Indoor Cable
(2-C Low Friction)
ODP-HRB-16/32 PS-1-8-ODP-HRB
IC-OF-SM-2D

Indoor Cable
(1-C Low Friction)

IC-OF-SM-1D

FUSE-CONNECT

ISC-UPC-FD

Splitter for ODC-HRB

PS-1-4-ODC-HRB ROSETTE

RS-IN-SC-1P/
ODC-HRB TC-MK-SC-1P

ODC-HRB (Cabinet) ODC-HRB(Rack) 19 inch Rack Cable Trunking and Accessories

ODC-HRB-420 ODC-HRB-RACK-480 TC-OF-R-19
ODC-HRB-240 ODC-HRB-RACK-240
ODC-HRB-180 or ODC-HRB-RACK-120

Cable Trunking Elbow (Flat Angle) T-Joint

Copyright©Fujikura Ltd./K.A Page 4 Guide book for FTTH-Premise v 1.0 May 2014)
 (Reference for Installation Work)

Copyright©Fujikura Ltd./K.A Page 5 Guide book for FTTH-Premise v 1.0 May 2014)
 (Reference for Installation Work)

Copyright©Fujikura Ltd./K.A Page 6 Guide book for FTTH-Premise v 1.0 May 2014)
 Instalasi Kabel Udara (SSW)
Penarikan Kabel Udara (SSW) SAG (Andongan kabel: d) PENARIKAN KABEL SSW:
= 1 - 2% x L
Kabel SSW bisa ditarik cukup
d dengan tenaga TANGAN tanpa
Do not pull cable while cable alat seperti TRACK TANG/
is laied on the ground!! KATREK.

SAG (Andongan kabel: d)

Jarak antara tiang (L) harus 1 s/d 2% (Max.) dari
panjang span antara tiang (L).

As far as it is practical, the cable

shall be installed so that the
suspension wire is always above
the cable part.

Suspension
PERHATIAN: Wire
At the cable laying, turns/twist (Melintir)
in the cable shall be released by turning
the cable winding while making the 8-
figure or to be pulled without making 8- Cable Part
figure.

Copyright©Fujikura Ltd./K.A Page 7 Guide book for FTTH-Premise v 1.0 May 2014)
 Pemasangan C-CLAMP
C-CLAMP shall be installed at:
1. Riser Point
2. Curve Point with the inner angle LESS THAN 120°
3. End Point of the cable with ODP-SSW-8 or ODP-PW-BR
150mm remove sheath

3. End Point
1. Riser Point 2. Curve Point 1) ODP-SSW-8
C-CLAMP x 2 10cm 50mm
C-CLAMP x 2

SSW CABLE

±30cm No cable slack is

required at the
90° Bend
end point with
ODP-SSW-8.
< 120°

± 1.0m
Cable part shall
be protected with
Spiral for outdoor 2) ODP-PW-BR
use (Black color)

Suspension Wire at C-CLAMP shall

LEGEND be bent ONLY after all ODP-SSW
installation have been completed
: SSW Cable (Japan) and the cable alignment has been
: C-Clamp (Japan) ± 1.5m confirmed so that no turn is
contained in the cable span.

Copyright©Fujikura Ltd./K.A Page 8 Guide book for FTTH-Premise v 1.0 May 2014)
 Pemasangan LINE-GUARD

(1) Suspension (2) Suspension .

TAMPA Line Guard DENGAN Line Guard

C-CLAMP x 2 < 120°

（２）
（１）
（１）
（１） （１） （２） （１） （１） （２） ........... C-CLAMP x 2

LINE GUARD shall be installed where: PERHATIAN:

1. One (1) in every three (3) poles in the straight line. LINE GUARD shall be fixed and the Suspension Wire at
C-CLAMP shall be bent ONLY after all ODP-SSW
2. At the pole beside the ODP-SSW is installed except the installation have been completed and the cable
location where C-CLAMP is installed. alignment has been confirmed so that no turn is
contained in the cable span.

Copyright©Fujikura Ltd./K.A Page 9 Guide book for FTTH-Premise v 1.0 May 2014)
 Pemasangan ODP-SSW-8 (Instalasi JIka Ada Permintaan Pemasangan)

1) At the location with C-CLAMP 2) At the location with Suspension-CLAMP

±30cm
±25cm
ODP-SSW-8

Line Guard ODP-SSW-8

±30cm L= 51cm

SUSPENSION CLAMP

±30cm

10cm PERHATIAN:
In case if LINE GUARD is not installed at the location
where ODP-SSW-8 will be installed, the LINE GUARD shall
be installed at the time of ODP-SSW-8 installation.

Copyright©Fujikura Ltd./K.A Page 10 Guide book for FTTH-Premise v 1.0 May 2014)
 (Reference for Installation Work)

Copyright©Fujikura Ltd./K.A Page 11 Guide book for FTTH-Premise v 1.0 May 2014)
 Slack for Branching ODP-SSW

Branching Cable
(SSW-8-core)

Main Cable
(SSW-12/24-core)

Sub duct or HDPE

± 1.5m

± 1.0m
33/40
± 1.5m ± 1.0m
± 1.5m

Slack for Main Cable Slack for Branching Cable

± 1.0cm

2m
1.5m

= 2 x 1.5m + 2m = 5m = 1.5m + 1.5m = 3m

Copyright©Fujikura Ltd./K.A Page 12 Guide book for FTTH-Premise v 1.0 May 2014)
 (Reference for Installation Work)

Copyright©Fujikura Ltd./K.A Page 13 Guide book for FTTH-Premise v 1.0 May 2014)
 ODP Pedestal
L=±6.0m (*1)

1m

ODP
1m
1m

ODP

Working Table 1.5m

HH-PIT-60
Note (*1): Remaining Cable Slack after
Cable Slack Length during ODP Installation Work: ODP Installation Work shall be pulled
L= 2 x (1.5m+1m)+1.0m=6.0m back and kept in HH-PIT-60.

Copyright©Fujikura Ltd./K.A Page 14 Guide book for FTTH-Premise v 1.0 May 2014)
 Slack for Branching ODP Pedestal
± 1m

± 1.5m

± 1.5m

Slack for Main Cable Slack for Branching Cable

1m

= 2 x (1.5m +1m)+ 1m = 6m = (1.5m + 1m) + 1.5m = 4m

Copyright©Fujikura Ltd./K.A Page 15 Guide book for FTTH-Premise v 1.0 May 2014)
 (Reference for Installation Work)

Copyright©Fujikura Ltd./K.A Page 16 Guide book for FTTH-Premise v 1.0 May 2014)
 Wall Mount ODP
(In case when ODP Installation will be done on the ground)

ODP-CA

1m
1m

2.2m 1m Note (*1): Remaining Cable Slack

ODP after ODP Installation Work shall be
pulled back and kept in HH-PIT-60.

Cable Slack Length during ODP Installation Work:

1.0m L= (1.0m+2.20m)x2+1.0m=7.40m =±8.0m (*1)
HH-PIT-60

Copyright©Fujikura Ltd./K.A Page 17 Guide book for FTTH-Premise v 1.0 May 2014)
 INSTALLATION OF ODP WALL (1)
Approx.
5cm
Gap between steel pipe (Ф
2") and ODP (Wall Mount) In case Gap between
Gap between steel pipe (Ф shall be less than 10cm steel pipe (Ф 2") and ODP
2") and ODP (Wall Mount) (Wall Mount) is more than
shall be less than 10cm 5cm, cables shall be
A (See Identification Marking protected with spiral or
detail.) (White color) shall be flexible pipe (Black color)
applied on the cable of
"Up-stream/ODC" side.
Approx.

Approx.
10cm

10cm
HDPE Pipe 33/40

Ф 2" Galvanized Steel Pipe

Clamps shall be attached Approx.

Galvanized Steel Pipe (Ф2") Details "A"
and Clamps shall be painted
Clamps shall be attached

with the same color with the

Approx. 2.20m

Approx. @ < 1.0m

HDPE 33/40 shall be

@ < 1.0m
wall.
installed until the level with
Galvanized Steel Pipe..

10cm
G.L.

30cm
Approx.

20cm
10cm

Approx.
10cm

B (See detail.)
10cm

G.L.
10c 30cm
30cm 30cm 30cm
m

Details "B"

Copyright©Fujikura Ltd./K.A Page 18 Guide book for FTTH-Premise v 1.0 May 2014)
 INSTALLATION OF ODP WALL (2)
(In case pipe shall be buried in the wall)

Flex. Pipe

Drop Cable

Approx. 100 OD=25mm

Steel flexible inside
Approx.
200 Approx. Flex-pipe R≧300
200
Approx. PVC/High-Impact
100 Flex-pipe
PVC Simple Conduit OD Ф25mm
R≧300
Socket for OD
25mm Pipe
Pipes shall be buried in the wall. Pipes shall be buried in the wall.
Pipe space shall be filled with Flex-pipe Pipe space shall be filled with
concrete after ODP installation. R≧300 concrete after ODP installation.

Note:
In case when pipes shall be buried in the building wall due to the
Appro requirement by the developer, the following points shall be taken into
x. 100 account for the installation.

Flex-pipe 1. HH-PIT-60 shall be installed in front of ODP location.

R≧300 2. Flexible Pipe with steel (OD 25mm) shall be used at the bending part of
HH PIT-60 HH PIT-60 Approx. 100 conduit.
Flex-pipe 3. Bending Radius of Flexible Pipe shall be more than 300mm.
4. PVC/High-Impact Pipe (OD 25mm) shall be used at the straight part of
150

R≧300 PVC/High-Impact
150 conduit.
Conduit OD Ф25mm
5. PVC Simple Socket for OD 25mm Pipe shall be used at all jointing part.
50 6. Pipe space of wall shall be filled with concrete after installation of ODP.
(ODP termination work shall be done prior to the pipe fixing and concrete
100 2 x PVC Ф50 work.)
(L=200)
7. The wall shall be restored to the original condition and painted with the
same color with the original wall.

MOM/BA shall be made (to be signed by the PIC of the developer) for the
confirmation of the requirement.

Copyright©Fujikura Ltd./K.A Page 19 Guide book for FTTH-Premise v 1.0 May 2014)
 (Reference for Installation Work)

Copyright©Fujikura Ltd./K.A Page 20 Guide book for FTTH-Premise v 1.0 May 2014)
 (Reference for Installation Work)

Copyright©Fujikura Ltd./K.A Page 21 Guide book for FTTH-Premise v 1.0 May 2014)
 Pemasangan Drop-Core KU (Instalasi JIka Ada Permintaan Pemasangan)

LEGEND

: S-Clamp (Japan)

: D-Clamp (Japan)
: BW-Clamp (Local)

Case-A (Drop-core Case-B (Drop-core at

Wire Grip 3/8" only at the end pole) the middle of the cable)
with double nut

Messenger wire from drop cable to pole or

φ1.2mm galvanized steel wire with sheath coating

Case-C (Drop-core only at

the middle of pole span)

Copyright©Fujikura Ltd./K.A Page 22 Guide book for FTTH-Premise v 1.0 May 2014)
 Cable

S clamp
Aerial Drop
cable

Customer's house wall House hook

House hook Supporting wire is tightly fixed on a

clamp

Optical Drop Cable

Cable core

Copyright©Fujikura Ltd./K.A Page 23 Guide book for FTTH-Premise v 1.0 May 2014)
 Drop Cable installation Drop Cable installation
with BW clamp without BW clamp
Cables to
Customer's house

Cable element
Cables from closure
BW clamp
Supporting wire

Supporting wire
Cables from closure

Taping Messenger wire

to pole
Cable element

Cables to Customer's house

S clamp

Copyright©Fujikura Ltd./K.A Page 24 Guide book for FTTH-Premise v 1.0 May 2014)
 Fixing of Drop cable
Supporting wire
(Steel)
Neck optical fibers
Cable Body
portion (fibers)

Step 1 ) Cut the neck of the cable with a cutter Step 2 ) Separate the supporting wire from the cable body

Approx. 25cm

Step 3 ) The length to be separated should be approximately 25cm.

Copyright©Fujikura Ltd./K.A Page 25 Guide book for FTTH-Premise v 1.0 May 2014)
 Fixing of Drop cable

supporting wire
supporting wire supporting wire

Important!!
End of supporting wire must be
taught with the metallic part
COMPLETED PIECE

supporting wire

Copyright©Fujikura Ltd./K.A Page 26 Guide book for FTTH-Premise v 1.0 May 2014)
 (Reference for Installation Work)

Copyright©Fujikura Ltd./K.A Page 27 Guide book for FTTH-Premise v 1.0 May 2014)
 Drop cable installation into ODP Pedestal
Use duct from ODP to customer premise

HH-PIT-40

HH-PIT-40 - Premises
1) BC-TR-0.4 + PP-OF-OUT(PVC ¾”)

HH-PIT-40

ODP (HH-PIT-60) – HH-PIT-40/

ODP Pedestal HH-PIT-40 – HH-PIT-40

HH-PIT-60 1) BC-TR-0.6 + DC-SD-1 Big

Copyright©Fujikura Ltd./K.A Page 28 Guide book for FTTH-Premise v 1.0 May 2014)
 (Reference for Installation Work)

Copyright©Fujikura Ltd./K.A Page 29 Guide book for FTTH-Premise v 1.0 May 2014)
 Examples of drop cable/indoor cable installation into house

Use Air Condition ducts Use Telephone ducts Drill new hole
(~10mm dia. )

Indoor cable

Outside

Indoor cable Outside Indoor cable

Outside

Copyright©Fujikura Ltd./K.A Page 30 Guide book for FTTH-Premise v 1.0 May 2014)
Copyright©Fujikura Ltd./K.A Page 31 Guide book for FTTH-Premise v 1.0 May 2014)
 ★Standard:
Bend the Cable top to avoid cable being stuck while pushing through conduits

About 10mm

Copyright©Fujikura Ltd./K.A Page 32 Guide book for FTTH-Premise v 1.0 May 2014)
 CORRECT PUSHING METHOD
Ensure the stroke length is short (about 50mm)
Correct Method Wrong Method

Photo

Stroke
Short (about 50mm) Avoid Long stroke length
length

What is knack of PUSHING METHOD？

→①Get back with about 100mm to find another route
②Prepare end shape of the cable
③If you bundle 2 low friction cables, you will be able to install them easier due to increasing stiffness.
Copyright©Fujikura Ltd./K.A Page 33 Guide book for FTTH-Premise v 1.0 May 2014)
 Examples of drop cable installation into house with trunking

Copyright©Fujikura Ltd./K.A Page 34 Guide book for FTTH-Premise v 1.0 May 2014)
 Examples of indoor cable installation inside house with trunking

Copyright©Fujikura Ltd./K.A Page 35 Guide book for FTTH-Premise v 1.0 May 2014)
 Examples of "ONU Hiding installation" into house

Copyright©Fujikura Ltd./K.A Page 36 Guide book for FTTH-Premise v 1.0 May 2014)
 Examples of drop cable installation into house

Copyright©Fujikura Ltd./K.A Page 37 Guide book for FTTH-Premise v 1.0 May 2014)
 Examples of drop cable installation into house ( Agata's home )

Copyright©Fujikura Ltd./K.A Page 38 Guide book for FTTH-Premise v 1.0 May 2014)
 Examples of drop cable installation into house ( Agata's home )

Copyright©Fujikura Ltd./K.A Page 39 Guide book for FTTH-Premise v 1.0 May 2014)