Scribd
Upload
156 views22 pages

Juni CBSD Tech Specs - 2018.02.28 - Rev

The document proposes three CBSD solutions for Charter Communications to trial: 1) an indoor Cat A CBSD for enterprise/SMB use, 2) an outdoor Cat B aerial CBSD for strand mounting, and 3) an outdoor Cat B CBSD for attach mounting. It provides details on the design, specifications, antenna patterns, and link budgets for each solution.

Uploaded by

Saran Khalid
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
156 views22 pages

Juni CBSD Tech Specs - 2018.02.28 - Rev

The document proposes three CBSD solutions for Charter Communications to trial: 1) an indoor Cat A CBSD for enterprise/SMB use, 2) an outdoor Cat B aerial CBSD for strand mounting, and 3) an outdoor Cat B CBSD for attach mounting. It provides details on the design, specifications, antenna patterns, and link budgets for each solution.

Uploaded by

Saran Khalid
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 22

Juni CBSDs

Technical Spec. for Charter

February 28, 2018

CAT-A Indoor CAT-A/B Strand CAT-B Attach

JuniFOR DISCUSSION
Proprietary and– Confidential
STRICTLY CONFIDENTIAL
© All rights Reserved
Juni CBSDs proposal for trial

Juni proposes 3 CBSD solutions to Charter Communications for trial this time:

1. Indoor (Cat A) – Enterprise/SMB

2. Outdoor (Cat B) – Aerial (Strand Mount)

3. Outdoor (Cat B) – Non-aerial (Attach Mount – Single Sector)

CAT-A Indoor CAT-B Strand Mount CAT-B Attach Mount

Juni Proprietary and Confidential © All rights Reserved


1. Indoor (Cat A) – Enterprise/SMB

Juni Proprietary and Confidential © All rights Reserved


1. Indoor (Cat A) – Enterprise/SMB
Product Design Key Specifications

- LTE Single Mode (CBRS Band 48)


- 10 / 20 MHz channel bandwidth
- Max Output Power (base power): 22dBm = 160mW per path (25dBm = 320mW with 2x2 MIMO)
JLT-622P - Antenna Gain: Max. 5dBi (external omni antenna)
Indoor (Cat A) CBSD
- Synchronization: IEEE1588v2 / GPS / Band 48 Air Sync / Band 41 Air Sync
- PoE+ Support
- Backhaul Type: Ethernet (RJ-45 1000 BASE-T)

Antenna Specification (JLT-622P)


Item Specification Remark
3550 - 3700MHz
Frequency Range
(Band 48)
Gain Max. 5dBi
VSWR 3.0:1
Polarization Linear
Impedance 50Ω
Size 11¢x160 mm Tilt type (45°, 90°)

* Noise Figure: Max. 6dB


* Rx Sensitivity: Min. -97dBm (Typ. -99dBm)
4

Juni Proprietary and Confidential © All rights Reserved


1. Indoor (Cat A) – Enterprise/SMB
Radiation Pattern (JLT-622P Antenna, 3550 – 3700MHz)

Juni Proprietary and Confidential © All rights Reserved


1. Indoor (Cat A) – Enterprise/SMB
VSWR (S11) for JLT-622P

Juni Proprietary and Confidential © All rights Reserved


1. Indoor (Cat A) – Enterprise/SMB
Link Budget (for JLT-622P)
JLT-622P Indoor Hotspot Comment/Assumption
Downlink Uplink
Channel Bandwidth MHz 20 20
Assumption
# of Tx antenna 2 1
# of Rx antenna 2 2
Total # of RBs 100 100
# of RBs used 100 36 Uplink: 36RB used / UE assumed
Subcarrier spacing KHz 15 15
Transmission bandwidth KHz 18000.0 6480.0
TX
Maximum power dBm 25.0 23.0 UE: CAT 3
Antenna gain dBi 5.0 0.0
Cable Loss dB 0.0 0.0
TX EIRP dBm 30.0 23.0
RX
Thermal noise density dBm/Hz -174.0 -174.0
RX noise figure dB 9.0 6.0 UE noise figure assumption: 9dB(3GPP 36.931)
RX noise density dBm/Hz -165.0 -168.0
Noise Bandwidth dB-Hz 72.6 68.1
RX noise power dBm -92.4 -99.9
Required SINR dB -13.60 -5.10 Set the value to get the Rx sensitivity below
RX sensitivity dBm -106.0 -105.0 Max Rx sensitivity is assumed
RX antenna gain dBi 0.0 5.0
Cable Loss dB 0 0.0
Other Losses and Gains
Selection Gain dB 3.00 3.00 Tx Diversity applied
Interference Margin dB 3.00 3.00 Ref: Practical Introduction to LTE Radio Planning, J. Salo et al.
Log Normal Fading Margin(LOS) dB 3.00 3.00 LOS 3dB, NLOS 4dB (3GPP 36.814)
Penetration loss
Penetration loss Walls 0 0 Vary according to the path loss model
Penetration loss Floors 0 0 Vary according to the path loss model
Maximum Allowable Path Loss dB 133.0 130.0

Juni Proprietary and Confidential © All rights Reserved


2. Outdoor (Cat B) – Aerial (Strand Mount)

Juni Proprietary and Confidential © All rights Reserved


2. Outdoor (Cat B) – Aerial (Strand Mount)
Product Design Key Specifications
- LTE Carrier Aggregation (CBRS Band 48)
- Integrated DOCSIS 3.0 (or 3.1, TBD) Cable Modem
- Supports PSE (PoE++) – Powering up other devices via UTP cable
JLT-733S
- Max Output Power (base power): 33dBm = 2W per path (36dBm = 4W with 2x2 MiMO)
Outdoor (Cat B) CBSD –
- Antenna Gain: Max. 5.5dBi (integrated omni antenna)
Strand Mount
- Synchronization: GPS / Band 48 Air Sync
- Backhaul Type: Coaxial Cable (DOCSIS)

Antenna Specification (JLT-733S)


Item Specification Remark
3550 - 3700MHz
Frequency Range
(Band 48)
Gain Max. 5.5dBi
VSWR 1.9:1
Polarization Linear
Impedance 50Ω

* Noise Figure: Max. 5dB


* Rx Sensitivity: Min. -97dBm (Typ. -100dBm)

Juni Proprietary and Confidential © All rights Reserved


2. Outdoor (Cat B) – Aerial (Strand Mount)
Radiation Pattern (JLT-733S Antenna, 3550 – 3700MHz)
- Azimuth Pattern

10

Juni Proprietary and Confidential © All rights Reserved


2. Outdoor (Cat B) – Aerial (Strand Mount)
Radiation Pattern (JLT-733S Antenna, 3550 – 3700MHz)
- Elevation Pattern

11

Juni Proprietary and Confidential © All rights Reserved


2. Outdoor (Cat B) – Aerial (Strand Mount)
Radiation Pattern (JLT-733S Antenna, 3550 – 3700MHz)
- Elevation Side Pattern

12

Juni Proprietary and Confidential © All rights Reserved


2. Outdoor (Cat B) – Aerial (Strand Mount)
VSWR (S11) for JLT-733S

13

Juni Proprietary and Confidential © All rights Reserved


2. Outdoor (Cat B) – Aerial (Strand Mount)
Link Budget (for JLT-733S)
JLT-733S Outdoor Comment/Assumption
Downlink Uplink
Channel Bandwidth MHz 20 20
Assumption
# of Tx antenna 2 1
# of Rx antenna 2 2
Total # of RBs 100 100
# of RBs used 100 36 Uplink: 36RB used / UE assumed
Subcarrier spacing KHz 15 15
Transmission bandwidth KHz 18000.0 6480.0
TX
Maximum power dBm 36.0 23.0 UE: CAT 3
Antenna gain dBi 5.5 0.0
Cable Loss dB 1.0 0.0
TX EIRP dBm 40.5 23.0
RX
Thermal noise density dBm/Hz -174.0 -174.0
RX noise figure dB 9.0 5.0 UE noise figure assumption: 9dB(3GPP 36.931)
RX noise density dBm/Hz -165.0 -169.0
Noise Bandwidth dB-Hz 72.6 68.1
RX noise power dBm -92.4 -100.9
Required SINR dB -13.60 -5.10 Set the value to get the Rx sensitivity below
RX sensitivity dBm -106.0 -106.0 max Rx sensitivity is assumed
RX antenna gain dBi 0.0 4.0
Cable Loss dB 0 1.0
Other Losses and Gains
Selection Gain dB 3.00 3.00 Tx Diversity applied
Interference Margin dB 3.00 3.00 Ref: Practical Introduction to LTE Radio Planning, J. Salo et al.
Log Normal Fading Margin dB 3.00 3.00 LOS 3dB, NLOS 4dB (3GPP 36.814)
Penetration Loss
Penetration loss Walls 0 0 eNB and UE are located at outdoor
Penetration loss Floors 0 0 eNB and UE are located at outdoor
Maximum Allowable Path Loss dB 143.5 129.0

14

Juni Proprietary and Confidential © All rights Reserved


3. Outdoor (Cat B) – Non-aerial (Attach Mount – Single Sector)

15

Juni Proprietary and Confidential © All rights Reserved


3. Outdoor (Cat B) – Non-aerial (Attach Mount)
Product Design Key Specifications

- LTE Carrier Aggregation (CBRS Band 48)


- Max Output Power (base power): 33dBm = 2W per path (36dBm = 4W with 2x2 MiMO)
JLT-733A
- Antenna Gain: Max. 14dBi (integrated patch antenna)
Outdoor (Cat B) CBSD –
- Synchronization: GPS / Band 48 Air Sync
Attach Mount
- Backhaul Type: Fibre (SFP) / Ethernet (RJ-45 1000 BASE-T)

Antenna Specification (JLT-733A)


Item Specification Remark
3550 - 3700MHz
Frequency Range
(Band 48)
Gain Max. 14dBi
VSWR < 1.5
Polarization ±45°

3dB Horizontal 65°


Beam Width Vertical 14°
Isolation Between Ports > 20dB
Impedance 50Ω

* Noise Figure: Max. 5dB


* Rx Sensitivity: Min. -97dBm (Typ. -100dBm)
16

Juni Proprietary and Confidential © All rights Reserved


3. Outdoor (Cat B) – Non-aerial (Attach Mount)
Radiation Pattern (JLT-733A Antenna, 3550 – 3700MHz)
- Azimuth pattern

17

Juni Proprietary and Confidential © All rights Reserved


3. Outdoor (Cat B) – Non-aerial (Attach Mount)
Radiation Pattern (JLT-733A Antenna, 3550 – 3700MHz)
- Elevation pattern

18

Juni Proprietary and Confidential © All rights Reserved


3. Outdoor (Cat B) – Non-aerial (Attach Mount)
VSWR VSWR
- S11 - S22

19

Juni Proprietary and Confidential © All rights Reserved


3. Outdoor (Cat B) – Non-aerial (Attach Mount)
Isolation between ports

20

Juni Proprietary and Confidential © All rights Reserved


3. Outdoor (Cat B) – Non-aerial (Attach Mount)
Link Budget (for JLT-733A)
JLT-733A Outdoor Comment/Assumption
Downlink Uplink
Channel Bandwidth MHz 20 20
Assumption
# of Tx antenna 2 1
# of Rx antenna 2 2
Total # of RBs 100 100
# of RBs used 100 36 Uplink: 36RB used / UE assumed
Subcarrier spacing KHz 15 15
Transmission bandwidth KHz 18000.0 6480.0
TX
Maximum power dBm 36.0 23.0 UE: CAT 3
Antenna gain dBi 14.0 0.0
Cable Loss dB 1.0 0.0
TX EIRP dBm 49.0 23.0
RX
Thermal noise density dBm/Hz -174.0 -174.0
RX noise figure dB 9.0 5.0 UE noise figure assumption: 9dB(3GPP 36.931)
RX noise density dBm/Hz -165.0 -169.0
Noise Bandwidth dB-Hz 72.6 68.1
RX noise power dBm -92.4 -100.9
Required SINR dB -13.60 -5.10 Set the value to get the Rx sensitivity below
RX sensitivity dBm -106.0 -106.0 Max Rx sensitivity is assumed
RX antenna gain dBi 0.0 14.0
Cable Loss dB 0 1.0
Other Losses and Gains
Selection Gain dB 3.00 3.00 Tx Diversity applied
Interference Margin dB 3.00 3.00 Ref: Practical Introduction to LTE Radio Planning, J. Salo et al.
Log Normal Fading Margin dB 3.00 3.00 LOS 3dB, NLOS 4dB (3GPP 36.814)
Penetration Loss
Penetration loss Walls 0 0 eNB and UE are located at outdoor
Penetration loss Floors 0 0 eNB and UE are located at outdoor
Maximum Allowable Path Loss dB 152.0 139.0

21

Juni Proprietary and Confidential © All rights Reserved


Thank you.

www.JuniGlobal.com

22

Juni Proprietary and Confidential © All rights Reserved

You might also like