Scribd
Upload
28 views

Phase 2

The document describes a system to identify black money using RFID tags. The system uses RFID tags attached to currency notes and an RFID reader connected to an ARM7 microcontroller. When a tagged note is scanned twice within 5 minutes, it is identified as black money and an alert is generated through a buzzer and SMS.

Uploaded by

annapoorna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
28 views

Phase 2

The document describes a system to identify black money using RFID tags. The system uses RFID tags attached to currency notes and an RFID reader connected to an ARM7 microcontroller. When a tagged note is scanned twice within 5 minutes, it is identified as black money and an alert is generated through a buzzer and SMS.

Uploaded by

annapoorna
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 12

S.S. E.

Trust’s
S. G. BALEKUNDRI INSTITUTE OF TECHNOLOGY, BELAGAVI
Department of Computer Science and Engineering

Academic year 2019


Phase II
(15CSP85)

“Effective Identification Of Black Money Using RFID”


Prepared By: Guided By:
Ms. Ankita. B. C (2BU15CS005) Dr. G. R. Udupi
Ms. Annapoorneshwari. R. K (2BU15CS006)
Ms. Erum Jamadar(2BU15CS018)
Ms. Kashmira. S. Daiv (2BU15CS025)
1
Introduction
 In March 2018, it was revealed that the amount of Indian
black money currently present in Swiss and other
offshore banks is estimated to be ₹90 lakh crores.

 The proposed system helps to eliminate black money


effectively.

2
Hardware Requirements
• RFID Tag • Capacitor 1000μF
• RFID reader • Regulator 7812,7805
• ARM7 LPC 2148 • Buffer IC 4050
• GSM Modem • Driver IC 2003
• GLCD • Relay 12V
• Transformer
• Buzzer
• Diode 4148
• Gtag or Serial port
• LED

3
Software Requirements
 Keil Software μVision 4 [ to save, build and
rebuild embedded c code]
 Flash Magic [to dump the code into ARM7
Microcontroller]

4
Implementation
Serial Number

Governor Name

Denomination
RFID
Card reader machine number TAG
Last operated date,timestamp

Fig : Currency with RFID tag


LCD DISPLAY

ARM GSM
READER PROCESSOR MODEM

TIMER BUZZER

Fig : Schematic principle of hardware implementation of black money


detection technique

6
Workflow
GLCD to ARM7 connection
Pin 4 P0.11 Register select
Pin 5 P0.12 Read/write
Pin 7 P0.22
Pin 8 P0.21
Pin 9 P0.20
Pin 10 P0.19 Databuses
Pin 11 P0.18
Pin 12 P0.17
Pin 13 P0.16
Pin 14 P0.15
Pin 17 P0.13 Chip selection 1

8
RFID READER TO ARM7
CONNECTION

Pin 1 Vcc Vcc


Pin 2 Ground Ground
Pin 3 Tx Rx0

GSM TO ARM7 CONNECTION


Vcc Vcc
Ground Ground
Tx Rx

9
Working
 The data like denomination, serial number, governor name is
stored in the ARM7 Microcontroller corresponding to the
RFID tag.
 The RFID tag is scanned using RFID reader.
 Once it is scanned the data corresponding to RFID tag is
displayed on GLCD.
 After 5 mins of time duration if the same RFID tag is
scanned then the GLCD displays the message as BLACK
MONEY.
 And at the same time Buzzer occurs alarming the retailer.
Remaining Work
 Generation of SMS after detecting black money.
 Buzzer when black money is detected.
THANK YOU

12

You might also like