Components
Uploaded by
Gyan Swaroop TripathiComponents
Uploaded by
Gyan Swaroop TripathiScience
Project
Resistors
A resistor impedes the flow of electricity through a circuit.
Resistors have a setvalue.
Since voltage, current and resistance are related through Ohm’s
law, resistors are a good way to control voltage and current in
your circuit.
2
More on resistors
Resistor colorcodes
1st band = 1st number
2nd band = 2nd number
3rd band = # of zeros / multiplier
4th band = tolerance
3
Color code
Tolerance: Gold = within 5%
Black: 0
Brown: 1
Red: 2
Orange: 3
Yellow: 4
Green: 5
Blue: 6
Violet: 7
Gray: 8
White: 9
4
Units
Knowing your units is important!
Kilo and Mega are common inresistors
Milli, micro, nano and pico can be used in other
components
K (kilo) = 1,000
M (mega) = 1,000,000
M (milli) = 1/1,000
u (micro) = 1/1,000,000
n (nano) = 1/1,000,000,000 (one trillionth)
p (pico) = 1 / 1,000,000,000,000 (one quadrillionth)
5
Capacitors
A capacitor stores electricalenergy.
This pool of electrons is available for electronic components to
use.
Capacitance is measured in Farads. The small capacitors usually used in
electronics are often measured in microfarads and nanofarads.
Some capacitors are polarized. Notethe
different length terminals on one of the capacitors.
6
Polarity of capacitors
The shorter terminalgoes
on the negative side.
The stripe is on the
negative terminal sideof
the capacitor.
The board is marked for
positive or negative.
7
Applications of capacitors
Capacitors supply a pool of electrons for immediate use.
If a component needs an immediate supply of electrons, the
capacitor can supply thoseelectrons.
Capacitors can smooth out a signal – eliminate the ripples
or spikes in DCvoltage.
The capacitor can absorb the peaks and fill in the
valleys of a rippledsignal.
8
Diode
A diode is a one way valve (or gate) for electricity. It is a
component with an asymmetrical transfer characteristic. A
diode has low (ideally zero) resistance in one direction, and
high (ideally infinite) resistance in the other direction.
Diodes will protect yourelectronics.
9
Diode circuit protection
In a DPDT switch, if polarity is wrong, the motor will run
backwards.
In an electronic circuit, if the polarity is wrong, you can fry
your components.
A diode in your system will help to prevent problems.
Diodes have a bar
on the cathode
(negative) side.
10
Light emitting diode (LED)
A light emitting diode (LED) is a semiconductor light source.
When electricity is passing through the diode, it emits light.
Jeremy is going to talk a lot more about LEDs.
11
Variable resistor / Potentiometer
A potentiometer is avariable resistor. As you manually
turn a dial, the resistance changes.
12
How a variable resistor works
As the dial/wiper turns, electricity must go through
more or less of the resistive strip.
In series, the change in resistance means a change in voltage.
So as you turn the
dial/wiper, you get
a change involtage.
13
Transistors
A transistor is a semiconductor device used to amplify
and switch electronic signals and electrical power.
This is our electronicswitch!
14
How a transistor works
A voltage or current applied to one pair of the
transistor’s terminals changes the current through
another pair of terminals.
A transistor is composed of semiconductor material
with at least threeterminals
for connection to an external
circuit.
Transistors have 3 pins.
For these transistors:
Collector
Emitter
Base
15
Terminology
BJT versus FET
Bipolar junction transistor. Useful asamplifiers.
Collector, Emitter, Base
Field-effect transistor. Useful as motordrivers.
Source, Drain, Gate
MOSFET: Metal-oxide-semiconductor FET
NPN (N-channel FET) versus PNP (P-channel FET)
NPN versus PNP is how the semiconductors are
layered. NPN: Not pointing in
PNP: Pointing in permanently
16
Schematic symbols
BJT PNP BJT NPN
P-channel FET N-channel FET
17
Integrated circuit
An integrated circuit (IC) is a set of transistors that is
the controller or ‘brain’ of an electronic circuit.
An input is received, an output is sent out.
Modern microprocessor ICs can have billions of
transistors per squareinch!
18
What an IC can do for us?
Billions of electronically controlled on/offswitches
(transistors) is how the microprocessor in a digital
computer ‘thinks’ and functions.
A computer has a wide range of tasks to perform.
But other ICs can complete simpler, discrete jobs.
For example, an IC can take a voltage input and output
commands to a motor.
19
IC Terminology: Op-amp
An operational amplifier (op-amp) is a set of
transistors inside the integrated circuit. They oftenare
the components doing the mathematicaloperations.
20
H-bridge
An electronic circuit that enables voltage to be applied
across a load in eitherdirection.
A DPDT switch also does this, but not electronically.
21
H-bridge
Need four electronicswitches.
Either have 1 and 4 closed. Or 2 and 3 closed.
What happens if both 1 and 2 areclosed?
The H-bridge allows electricity to flow both ways across themotor,
which gives us forward andreverse.
We can use pulse width modulation to control how often the
switches are on versus off, which gives us speed control.
22
Varying voltage
A potentiometer/variable resistor allows you to
change the voltage input that goes into the integrated
circuit.
Integrated circuit can now output variety of pulse widths
to the transistors on theH-bridge.
This combination of potentiometer, integrated circuitand
PWM to the H-bridge is the key to speed control.
23
Why not skip the IC?
There are a couple reasons we don’t use just a
potentiometer to control the speed of our motors.
Potentiometers are rarely used to control significant power (more
than a watt).
You would still need a way to switch the direction of the motor. Just
using a potentiometercan control speed, but not direction.
DPDT switch and potentiometer combinations can lead to
problems if you quickly switch from full forward to full reverse.
Problems can occur if the polarity of a spinning DC motor gets
suddenly switched from forward toreverse.
Current surge
Mechanical stress
24
Printed Circuit Board
Components are attached to a printed
circuit board.
The ‘front’ side of the board will have
printed component information, such
as resistor # and resistance, diode type
and polarity, etc.
Holes go all the way through the board
from one side tothe other. Through-
hole soldering is needed to connect
components to the board.
25
Back of Circuit Board
The ‘back’ sideof the board will have lines indicating
connections between components. The lines on the
back are similar towires.
Thicker lines denote more current (electrons)moving
through.
Components connect the lines.
26
Conclusion
Hopefully that wasn’ttoo confusing.
The goal was to give you a basic
understanding of how some of the electronic
components of a motor speed controller
work.
There are lots of tools to help you with the
basics.
27
Thanks You
by
Yana Sharma
