Scribd
Upload
192 views

Tutorials For STM32F103RB: Nicolas Barbot

This document provides tutorials for using the STM32F103RB microcontroller. It covers topics like creating projects in OpenSTM32 and STMCubeMX, and using general purpose input/output (GPIO), UART, timers, analog-to-digital conversion, digital-to-analog conversion, and FLASH. Specific tutorials are provided on identifying GPIO pins, configuring GPIO for input, output, and interrupts, evaluating GPIO performance, and using interrupts to activate an LED when a button is pressed. Resources for the Nucleo-F103RB board and STM32Cube software are also listed.

Uploaded by

car
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
192 views

Tutorials For STM32F103RB: Nicolas Barbot

This document provides tutorials for using the STM32F103RB microcontroller. It covers topics like creating projects in OpenSTM32 and STMCubeMX, and using general purpose input/output (GPIO), UART, timers, analog-to-digital conversion, digital-to-analog conversion, and FLASH. Specific tutorials are provided on identifying GPIO pins, configuring GPIO for input, output, and interrupts, evaluating GPIO performance, and using interrupts to activate an LED when a button is pressed. Resources for the Nucleo-F103RB board and STM32Cube software are also listed.

Uploaded by

car
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 13

Tutorials for STM32F103RB

Nicolas Barbot

2016
Tutorials for STM32F103RB 2

• Create an OpenSTM32 Project

• Create a STM32CubeMX Project

• GPIO

• UART

• Timer

• Analog to Digital Conversion

• Digital to Analog Conversion

• FLASH
Tutorials for STM32F103RB 3

• Ressources
• Nucleo F103RB
• http://www.st.com/content/st_com/en/products/evaluation-tools/product-evaluation-
tools/mcu-eval-tools/stm32-mcu-eval-tools/stm32-mcu-nucleo/nucleo-f103rb.html
• This page contains user manual UM1724 describing the hardware of Nucleo boards
• STM32F103RB
• http://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-
mcus/stm32f1-series/stm32f103/stm32f103rb.html
• This page contains reference manual RM0008 describing STM32F103RB
• STM32 Cube F1
• http://www.st.com/content/st_com/en/products/embedded-software/mcus-embedded-
software/stm32-embedded-software/stm32cube-embedded-software/stm32cubef1.html
• This page contains UM1850 describing the HAL library
• Open STM32
• http://www.openstm32.org/HomePage
• Open STM32 is a free Eclipse plugin for programming STM32 MCU (registration needed).
• Eclipse
• https://www.eclipse.org
• Eclipse is the IDE software
Using GPIOs
Using GPIOs 5

• Goals:
• To identify a GPIO pin from the datasheet
• To configure and use GPIO with HAL drivers (input, output, interruption)
• To evaluate the performance of GPIO pin (frequency)

• Requirement
• Create an OpenSTM32 Project
Identify a GPIO pin 6

• Open User Manuel 1724 « STM32 Nucleo-64 boards » [1]


• This document describes the hardware layout of each Nucleo boards.
• Table 11 (page 37) presents the correspondance between Nucleo pins (on the
extension connectors) and STM32 pins.

• Nucleo boards provide a user led called LD2


• LD2 is connected to D13 on the Arduino connector (see LED p.22)
• Table 11 indicates that D13 corresonds to PA5 for STM32F103RB
• PA5 stands for Port A Pin 5

• In this tutorial, we will configure the STM32 to blink LD2 with a period
of 1 s
Create the Project 7

• Create a new project for STM32F103RB using HAL library


• See “CreateOpenSTM32Project” presentation

• Add the SystemClock_Config function in main.c


• Set HCLK to 64 MHz

• Call SystemClock_Config and HAL_Init function in main().


USING GPIO 8

• Open User Manuel 1850 « Description of STM32F1xx HAL drivers » [3]


• Chapter 18 (p. 247) describes the use of GPIO with HAL drivers

• Declare a GPIO_InitTypeDef structure in main() function


• Fill up the structure fields:

Mode Pull Speed Pin


Input No pull Low 0
Analog Pull up Medium 1
Output Pull down High 2
Alternate F. …
Interrupt 15

• Set the fields to GPIO_MODE_OUTPUT_PP, GPIO_NOPULL,


GPIO_SPEED_FREQ_LOW, GPIO_PIN_5
• Call the macro __HAL_GPIOA_CLK_ENABLE() to activate port A
• Configure the GPIO pin(s) using HAL_GPIO_Init()
Using GPIO 9

• You can now drive your GPIO pin with the function HAL_GPIO_WritePin() or
HAL_GPIO_TogglePin().
• Write a infinite loop to blink LD2 every 1 seconds.

• Your main() function should look like this:

• Build your project and run your program on the board


Evaluate the performance of GPIO 10

• In this exercise, we want to toggle D13 (on the Arduino connector) at the
maximum frequency
• Identify port and pin number of D13
• Create a new project (or modify the previous one)
• Configure the pin corresponding to D13 as an output
• In an infinite loop, toggle D13 (without delay)
• Build the project
• Observe D13 with an oscilloscope and determine the maximum frequency
Activate LED when button is pushed 11

• In this exercise, we want to activate LD2 when B2 (user button) is pressed


• Identify port and pin number of B2 (and LD2)
• Create a new project (or modify the previous one)
• Configure the pin corresponding to LD2 as an output
• Configure the pin corresponding to B2 as an input
• In an infinite loop, read the state of the pin corresponding to B2 and write this state
to the pin corresponding to LD2
• Build the project and debug your program
Generate INT when button is pressed 12

• In this exercise, we want to generate an interruption when B2 (user button) is


pressed to switch on LD2
• Identify port and pin number of B2 (and LD2)
• Create a new project (or modify the previous one)
• Configure the pin corresponding to LD2 as an output
• Configure the mode of B2 pin to GPIO_MODE_IT_FALLING
• Configure the priority interruption with HAL_NVIC_SetPriority() function
• Enable the interruption with HAL_NVIC_EnableIRQ() function
• Each interruption calls EXTI15_10_IRQHandler() (defined in
startup_stm32f103xb.s) which can be overloaded
• Overload the function EXTI15_10_IRQHandler() to call
HAL_GPIO_EXTI_IRQHandler() function
• Write the callback function HAL_GPIO_EXTI_Callback() to switch on the LED
• Build the project and debug your program
Conclusion 13

• Thanks to this tutorial, you are now able to:


• Use any GPIO as output
• Use any GPIO as input
• Use any GPIO for generating an interruption

You might also like