INSTALLATION OF

HARDWARE COMPONENTS
AND OTHER PERIPHERALS
What is Installation?

Fixed or semi-fixed location of a complete system

or a self-contained unit, with its accompanying
assemblies, accessories and parts. Installation
generally also includes provision of or connection
to services (such as power and other devices)
required to make the installed equipment ready
for operation.
One of the basic skills that you must
acquire in computer hardware
servicing is to independently assemble
and disassemble a personal computer
or simply setting up a PC.
Personal Computer Disassembly
Before starting computer
disassembly, make sure you have
the tools you need and they're all
close by and handy and be sure to have
a container to keep the screws in so
you have them when you want to put
things back together.
Step1. Unplugging
*The first thing you do is to unplug every cable
that is plugged in to your computer. That
includes the cables such as Power, USB,
Mouse, Keyboard, Internet, Ethernet, Modem,
AM\FM Antenna, Cable TV, etc. Just unplug all
the cables for safety purposes.
*Now that your computer is fully unplugged,
move your PC to a clean work space.
Step2.Opening the Outer Shell/Case

First, unscrew the four screws at the back of

the computer. On most computer cases,
there will be large knobs that you can
unscrew by hand or by screw driver on the
back-right side of the computer. The left side
has small screws because on that side you
can't access much on the inside.
Step2.Opening the Outer
Shell/Case

Figure 32. Screw at the back of computer chasis

Once the screws are removed, you
can remove the side panels. On most
computers, they just slide off. Start with
the left side panel (the side that once
had the knobs), slide it towards the back
of the computer. Now you can remove
the left panel. Just like the other side, slide
it towards the back of the computer.
NOTICE:
If you are working on a carpet, about
every five minutes touch something that
is grounded (Sink faucet / pipe, wire
coming from the ground part of a wall
outlet). This is done so you do not shock
your motherboard or other parts.
Step3. Removing the System Fan
First, unplug the fan from the motherboard.
You can find the plug by following the wire
from the fan. It should be labelled
"SYS_FAN1". Next, you will have to unscrew the
fan from the outside. You should now be able to
lift the fan out of the PC.
Step4. Removing the CPU Fan
The CPU fan is located right on top of the CPU
heat sink, which is a large piece of metal with
fins on the top. The CPU fan plugs into the
motherboard in an awkward place, that is
hard to access. But just follow the wires
and you should easily find it. It is labeled "CPU
FAN1". To remove the fan from the heat sink,
remove the four screws securing it in place.
Step5. Power
Supply
The first thing to do is
unplug every wire
coming from the power
supply. You must
disconnect the
motherboard (very
large connector/plug),
CD/DVD drive(s)
power, internal hard
drive power and
portable hard drive
slot power.
Once everything is unplugged,
unscrew the four screws holding the
power supply in place, on the back
of the computer. Next, push the
power supply from the outside, and
then lift it out.
Step 6. CD/ DVD Drive(s)
First,unplug
the ribbon from
the back of the
drive. Once that
is completed,
pull on the tab
securing the
drive in place,
then push it out
from the inside.
Figure 37. Location of CD / DVD Drive
Step7. Hard Drive
First, unplug the connector at
the back of the slot, and unplug
the other end from the
motherboard. Also unplug the
SATA cable from the
motherboard and the hard
drive. The portable hard drive
slot is secured the same way
the CD/DVD drive is, with a
tab. Pull on the tab, then
slide the slot out.
 To remove the
hard drive from
the side of the
slot, unscrew the
four screws
securing it in
place. You must
be very careful
not to drop the
hard drive, since
it is very
delicate!
Step8. Memory (RAM)

To remove the RAM, push down on both tabs holding

the RAM in place, which are located at both ends of
the RAM.
Step9. Motherboard
The motherboard
has seven screws
holding it to the
frame, which are
indicated by large
white circles
around them.
Remove them and
then lift the
motherboard out of
the frame.
Personal Computer Assembly
Now that you have the skills in
disassembling a personal computer, I
believe that you are ready to take
another step of this module which
is assembling a personal computer.
All you need to do is to follow the
step by step procedures provided in
this module.
Step 1. Prepare your workplace
1. Take Inventory:
Before you start,
take an inventory of
your parts. Do not
begin assembling
your computer if you
don't have everything
you need. Begin the
step-by-step process
once you are ready
with everything you
need.
2. Make Space, Make Time:
Building a PC takes up space - about a
dining room table worth. So make sure
you have plenty of working room and
a few hours to proceed with minimal
interruption. Work on a flat, stable table
top surface, or bare floor, where you have
room to layout all of the items.
 3. Prepare Grounding Protection:
Use an inexpensive
antistatic wrist strap.
Make sure you are
wearing your antistatic
wrist strap correctly (it
does you no good at all
if you do not wear it!),
and you are ready to
proceed. Look at Figure
43 for details.
4. Have the Drivers Ready:
Assuming you have another internet
connected PC, download the latest drivers
from the vendors' websites for each
component you will be installing.
Sometimes drivers are updated between
the time the component was
manufactured and the time you are
installing it. It is always best to have
the latest. Copy them to a CD for easy
access.
 Step 2. Prepare the Motherboard
1. Great care should be
taken when installing the
motherboard. First, take
the board out of its
packaging and put it on
top of the antistatic bag
it came in (see Figure
45). Remember, you always
want to safeguard your
components from
potentially hazardous
static electricity (wear
Figure 44. Motherboard in an Antistatic Bag
your strap).
 2. Before you
secure the
3. Next, review the motherboard manual, to
motherboard
make sure you are familiar with the
onto the PC
motherboard layout and understand which
case/chassis,
socket is which. Manuals are
inspect it
extremely helpful, usually easy to read, and
carefully for
include illustrations. Below you
any visible
can find instructions on how to install the
defects.
processor, the heat sink and the
memory modules on the motherboard. You
should not place the motherboard
in the computer case until you are told to do so.
Step 3. Install the CPU
1. Use the unlocking mechanism
to open the CPU socket which is
usually a lever.
2. Carefully line up the pins and
place the chip in its socket; it will
fit only when oriented the
proper way. An arrow or a missing
pin on one corner of the chip
will show you how to line things
up.
3. Align Triangular CPU and
socket key marks as shown in
Figure 46.
4. Lower the lever to lock the
CPU into place.
Step 4. Install the CPU Heat Sink
1. Follow the
manufacturer's directions to
install the heat sink and the
fan that will cool the
processor. If you bought an
OEM CPU and a separate
heat sink, you may need to
spread a thin layer of the
thermal grease that came
with the heat sink over the
chip to ensure proper
transfer of heat (some
heat sinks come with this
grease already applied).
 3. Attach the clip that
holds the heat sink in
place keeping in mind
that it may require a fair 4. Plug the CPU fan's
amount of force. Again,
follow the instructions that
power connector into the
came with the heat sink. proper connector on the
They will show you how to
fit it correctly. If you are motherboard.
in doubt, you can visit the
manufacturer's website for
more information.
 Step 5. Install Memory (RAM Modules)
In order to install the memory
modules, insert them into the
proper sockets (Figure 48) and
push down firmly but evenly until
the clips on both sides of the socket
pop into place. If your motherboard
supports dual channel memory,
consult the user manual to
determine which pairs of RAM
sockets you should use. The
motherboard and the CPU are the
brain and nerve center of your PC, so
selecting these components is the
most important decision you'll make.
Step 6. Place the motherboard into the case

1. Some PC cases
have a removable
motherboard tray.
If yours does,
remove the screws
holding it in place
and pull it out of
the case (Figure
49).
 2. Note the pattern of
the holes in your
motherboard (Figure
50), and screw brass
standoffs into the
motherboard tray or
into the PC case in
the correct locations
(ALWAYS check the
manual and follow
their instructions to
the letter).

Figure 49. Screw Brass Standoffs Into the Motherboard

3. Check the layout of the
sockets on the motherboard,
and confirm that the ports on
your motherboard's back
panel match the holes on 4. Carefully position the motherboard
the case's Input/Output on top of the brass standoffs (Figure
(I/O) shield that is installed
in your case. If necessary, 51), line up all the holes, and use the
remove the old I/O shield screws that accompanied the case to
by tapping it firmly a few fasten down the motherboard. If you
times with the butt-end of a
screwdriver, and then are using a removable tray in your
replace it with the shield that system, slide the tray and
came with the new motherboard back into the case and
motherboard.
then secure the tray.
 Step 7. Connect the Power Supply
1. First, plug the large ATX power
Making the proper
connections is crucial to connector (Figure 53) from your power
successfully assembling supply into the matching port on your
your PC system. motherboard. Look Figure X for details.
Fortunately, 2. Locate the smaller, square
manufacturers provide processor power connector (Figure
color-coded power 54) (you cannot miss it - it is the
cables and unique
one sprouting the yellow and black
connector shapes to
make the job easy. wires) and attach it to the
motherboard.
 Note: your
connector is usually
located near the
processor. As
always, refer to your
motherboard's
manual for the exact
locations.
3. Use your
motherboard user
manual and find
the description
about front-panel
connectors.
NOTE:
You are going to be doing work that requires attention to detail
and can be quite frustrating if you do not go into it with the right
attitude.
 4.Attach each of the tiny leads from the
power and reset switches (Figure 56), the
hard-disk activity lights, the PC speaker,
and any front-panel USB and FireWire
ports to the corresponding pin on your
motherboard. The needle -nose pliers are
useful for manipulating small pieces.
Step 8. Install Graphics / Video Cards

1. Begin by removing the backplane cover from

the AGP or PCI Express X16 slot (the metal piece
where the monitor connector will emerge) (Figure 55)
2. Install the
graphics board in
that slot, and then
secure the card with
a screw (Figure 56).
Step 9. Install Internal Drives
Now it is time to install your drives. This is an easy process,
but it requires attention to detail.

1. Make any necessary changes to jumpers on the drives before

mounting them in the case. A two-drive system (one or two SATA
(Serial ATA- is a standard hardware interface for connecting hard
drives and CD/DVD drives to a computer) hard drives, plus one
parallel ATA (Advanced Technology Attachment) optical drive, for
example) is easy to set up; the SATA drives are jumper less, and
the optical drive can be set as master on its own parallel ATA
channel. Many cases have removable drive rails or cages to
house drives
 2. Use the included
screws to attach your
drives to the rails or
cage, and slide them 3. When the drives are installed, connect power and data
into the case. For cables to each one.
externally accessible Parallel ATA drives use wide, flat data cables that can be
drives such as a DVD installed only in the
recorder, you can save correct way. Floppy drives use a similar but smaller cable;
time by installing one SATA drives use a
drive rail and sliding the thin, 1cm-wide data cable. SATA drives use a new type of
drive in for a test fitting power connector
to make sure that its that many power supplies don't come with. Fortunately,
front is flush with the many motherboards
case (Figure 57). ship with adapters for converting a standard four-pin
power connector to a
SATA power connector (Figure 57).
Step 10. Install the Add- in Cards
1. For each add-in card, you must choose a free PCI slot.
2. Remove its backplane cover to allow access from the
rear of the case.
3. Carefully position the card above the slot, and press
down firmly to seat the card (Figure 59).
4. Secure the card with a screw.
 Many motherboards have additional sound
connectors or ports housed on small add-in
boards. Some of these plug into slots on the
motherboard; others screw into the back of the
case in place of slot covers. Usually the
additional ports are not essential to your PC's
operation. For example, if you install a sound
card, you do not need connectors to the
motherboard's built-in sound chip. Check your
motherboard manual to determine what each
of these boards does.
Connecting Peripherals of a Personal
Computer
When attaching hardware and peripherals of
the computer, ensure that they are connected
to the correct locations or ports. For
example, some mouse and keyboard cables
use the same type of PS/2 connector. So, you
must know first the different ports that can be
found in the back panel of the computer.
Steps in Connecting Peripherals of a PC
Step 1. Attach the monitor cable to the video port.
Step 2. Secure the cable by tightening the screws on the connector.
Step 3. Plug the keyboard cable into the PS/2 keyboard port.
Step 4. Plug the mouse cable into the PS/2 mouse port.
Step 5. Plug the USB cable into a USB port.
Step 6. Plug the network cable into the network port.
Step 7. Plug the power cable into the power supply.
Computer Hardware
Servicing