NETWORK

A network consists of two or more computers that are linked in order to share
resources (such as printers and CD-ROMs), exchange files, or allow electronic
communications. The computers on a network may be linked through cables,
telephone lines, radio waves, satellites, or infrared light beams.
There are three basic types of networks which includes the following:
Local Area Network (LAN)
Wide Area Network (WAN)
Local Area Network
A Local Area Network (LAN) is a network that is confined to a relatively small
area. It is generally limited to a geographic area such as a writing lab, school, or
building. Rarely are LAN computers more than a mile apart.
In a typical LAN configuration, one computer is designated as the file server.
It stores all of the software that controls the network, as well as the software that can
be shared by the computers attached to the network. Computers connected to the
file server are called workstations. The workstations can be less powerful than the
file server, and they may have additional software on their hard drives. On most
LANs, cables are used to connect the network interface cards in each computer.
Wide Area Network
Wide Area Networks (WANs) connect larger geographic areas, such as
Florida, the United States, or the world. Dedicated transoceanic cabling or satellite
uplinks may be used to connect this type of network.
Networking Devices
Consist of, but are not limited to non-local printers, workstations, servers,
webcams, data loggers, instruments, dial-in devices, and, in general anything that
requires an Ethernet connection. These devices are supported on a best-effort basis
limited by the staffing and equipment level available.

57

Hub is a small, simple, inexpensive device that joins

multiple computers together. Many network hubs
available today support the Ethernet standard. Other
types including USB hubs also exist, but Ethernet is
the type traditionally used in home networking.

Ethernet switch is a device that gathers the signals

from devices that are connected to it, and then
regenerates a new copy of each signal.

Bridge is a device filters data traffic at a network

boundary. Bridges reduce the amount of traffic on a LAN
by dividing it into two segments.

Routers are small physical devices that join multiple networks

together.
Network gateway is an internetworking system
capable of joining together two networks that use
different base protocols. A network gateway can be
implemented completely in software, completely in
hardware, or as a combination of both.

Modem is a contraction of the terms modulator and

demodulator. Modems perform a simple function:
They translate digital signals from a computer into
analog signals that can travel across conventional
phone lines. The modem modulates the signal at the
sending end and demodulates at the receiving end.

58

Network interface is a device that connects a client computer, server, printer or

other component to your network. Most often, a network
interface consists of a small electronic circuit board that is
inserted into a slot inside a computer or printer. Alternatively,
some computers, printers, or other services include network
interfaces as part of their main circuit boards (motherboards).

Network firewall protects a computer network from

unauthorized access. Network firewalls may be
hardware devices, software programs, or a
combination of the two. Network firewalls guard an
internal computer network (home, school, business
intranet) against malicious access from the outside.
Network firewalls may also be configured to limit
access to the outside from internal users.

Direction: Identify what is being described in the following sentences and write your
answer on a separate sheet of paper.
1.It protects a computer network from unauthorized access.
2.Type of network that connect larger geographic areas, such as
Florida, the United States, or the world.
3.This is an internetworking system capable of joining together two
networks that use different base protocols.
4.It is consists of two or more computers that are linked in order to
share resources (such as printers and CD-ROMs), exchange files, or
allow electronic communications.
5.They translate digital signals from a computer into analog signals
that can travel across conventional phone lines.
6.It is a device that connects a client computer, server, printer or
other component to your network.
7.A device filters data traffic at a network boundary.
8.It is a device that gathers the signals from devices that are connected to
it, and then regenerates a new copy of each signal.
9.It is a small, simple, inexpensive device that joins multiple
computers together.
10.Type of network that is confined to a relatively small area.

59

Now, that you are done with the introduction of network as well as the
networking devices, to enlighten your understanding and knowledge have some
more readings about it thru books and other resources. You should consider the
following topics for research:
1.Different types of Network Topology
2.Common networking tools
After the research, you can also deepen your understanding by watching
a video presentation using the URL below:
o.http://www.professormesser.com/free-a-plus-training/220801/network-devices/

ohttp://www.professormesser.com/free-a-plus-training/220801/network-topologies-3/

After the video presentation here are your tasks:

1.List down all the network devices and their advantages
cited in the video.
2.List down the different network topologies and their
differences.
60

MATERIALS, TOOLS, EQUIPMENT and TESTING DEVICES

The following tools and equipment are classified according to their
functions and uses.
Equipment and
Accessories
LAN Card
UPS
Server
24 port-hub
Modem
Fax machine
PC Video camera
USBExternalCD writer
USB scanner
USB printers
USB Flash Drive

Tools
Screwdriver(standard)
Screwdriver(Philips)
Long nose pliers
Mechanical pliers
Allen wrench
Multitester
Crimping tools
Soldering iron (30 watts)
Wire stripper
LAN Tester
Anti-static wrist wrap
Device drivers/installers

Materials
Software applications
Network OS Software
RJ 45
UTP Cat 5 cable
Motherboards manual
and installer
Sound device driver
installer

LAN Card is a network interface card. This is a

computer circuit board or card that is installed in a
computer so that it can be connected to a network.

Server is a part of a network. It is a special

computer that users on the network can access to
carry out a particular job.

Port hub /Port is a connector on the back of a

computer or other device. A port is either a serial port
or a parallel port.
Modem - (Modulator-Demodulator) The modem is a
device that allows a given computer to share data or
otherwise a device which let computers exchange
information

61

Scanner- it is an input device that read text or

illustration printed on paper, translates the
information into a form that a computer can use
Flat Screw Driver is used to drive or
fasten negative slotted screws
USB Universal Serial Bus, a hardware
interface for low-speed peripherals such as the
keyboard,
mouse, joystick, scanner, printer and telephony
devices.
Printer - is a piece of hardware that produces
a
paper copy (also known as hardcopy) of the
information generated by the computer.
RAM Random Access Memory, is a primary
memory. This memory is used inside the
computer to hold programs and data while it is
running.
BIOS Basic Input / Output System, chip
that controls the most basic functions of the
computer and performs a self-test every time you
turn it on.
Flash drive RAM that can retain data
without electrical power. It is widely used for
BIOS chips and for digital camera and digital
music storage
Video Camera - camera using
videotape: a camera that records onto
videotape
Long nose Pliers is used for holding,
bending
and stretching the lead of electronics component
or connecting wire.
Soldering Iron is used to join two or more metal
conductors with the support of soldering lead
melted around it.

Desoldering Tool is used to unsolder

unwanted
parts or component in the circuit with the support
of soldering pencil
62

 Philips Screw Driver- is used to drive or fasten

positive slotted screws

LAN Tester- for RJ11,12,45 & BNC w/ Remote Unit

This ergonomic tester is designed to test most
network cable wiring. You can either conduct an
auto or manual test.

UTP Unshielded Twisted Pair, is a popular type of

cable used in computer networking that consists of
two shielded wires twisted around each

Using Testing Tools and Equipment

A. Direction: Identify the following tools and materials, give their uses.

1.

2.
3.

4.
63

B. Identification.
Direction: Identify the appropriate term described in each sentence. Use a
separate sheet for your answers.
1. It is a connector at the black of a computer or other device.
2. A computer circuit board installed in a computer so that it can be
connected to a network.
3.A device that allows a given computer to share a data.
4. An input device that read text or illustration printed on paper, translated
the information into a form that a computer that can use.
5.The least expensive and most popular network media.

For you to deepen your knowledge and skills and understanding in planning
and preparing for installation, you need to determine the location of the devices /
systems to be used, obtain materials necessary to complete the work in accordance
with established procedures and check the materials received against job
requirements . Your task is to have a research, find as well and watch video
presentations relating and showing the following:
1.Consult appropriate technical personnel to ensure that work is
coordinated with others who are involved in the activity;
2.Proper location / storage of the devices / systems and materials;
3.Correct way of obtaining the necessary materials to complete the work;
4.Fill up job order forms, request form and report sheets; and
5.Appropriate procedures in in checking the materials received.
After doing the above tasks, make sure that you have a detailed
documentation of it. Write your reflections on your notebooks or other sheet of paper.

After reflecting on the task given to you, its your chance now to transfer what
you have learned from the activity by having a presentation in front of the class. You
will be grouped with 5 members during the presentation. Make use of your creativity
in presenting each topic to awaken the interest of your classmates.

64