Scribd
Upload
476 views

Finite Element Analysis of Aircraft Wing Using Composite Structure

This document summarizes a journal paper on finite element analysis of an aircraft wing made of composite materials. The paper models a subsonic aircraft wing as a laminated composite shell structure. It develops a finite element model of the wing in ANSYS with over 47,000 elements. The model applies boundary conditions to simulate the wing being fixed at one end as a cantilever. It then performs analyses by applying loads including gravity and in different directions. The results show deflections, strain energies, and stresses on the wing to understand its structural behavior under various loads. The conclusions discuss the wing's response to individual and combined loads.

Uploaded by

Aumair Malik
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
476 views

Finite Element Analysis of Aircraft Wing Using Composite Structure

This document summarizes a journal paper on finite element analysis of an aircraft wing made of composite materials. The paper models a subsonic aircraft wing as a laminated composite shell structure. It develops a finite element model of the wing in ANSYS with over 47,000 elements. The model applies boundary conditions to simulate the wing being fixed at one end as a cantilever. It then performs analyses by applying loads including gravity and in different directions. The results show deflections, strain energies, and stresses on the wing to understand its structural behavior under various loads. The conclusions discuss the wing's response to individual and combined loads.

Uploaded by

Aumair Malik
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 22

ASSIGNMENT # 9

JOURNAL PAPER
PRESENTATION
Finite Element Analysis of
Aircraft Wing Using
Composite Structure

PAPER PUBLISHED IN THE INTERNATIONAL


JOURNAL OF ENGINEERING AND SCIENCE
(IJES) 2013 :
By Dr. R. Rajappan

(HOD Department Of
Mechanical Engineering, Mailam Engineering College,
India)

V. Pugazhenthi (M.E Student Final Year)


ISSN: 2319 1813 ISBN: 2319 1805

ABSTRACT
The thesis deals with bending Finite Element
Analysis of monocoque laminated composite
aircraft (subsonic and supersonic) wing using
commercial software ANSYS.

Theoretical background, mathematical


formulation and finite element solution for a
laminated composite shell structure are

A monocoque aircraft wing is made of


laminated composite with fiber angles in
each ply aligned in different direction.

Monocoque is an aircraft or vehicle structure


in which the chassis is integral with the body.

Various airfoil thickness and ply angles were


considered to study the effect of bendingtorsion decoupling.

SUBSONIC AIRCRAFT WING


MODEL DESCRIPTION AND
CASE
STUDIES
Physical Model of subsonic Aircraft wing:
The physical structure modeled in this work is a shell aircraft
wing of airfoil cross section NACA 4412 series with fiber
laminated composite structure, shown in figure below

SUBSONIC AIRCRAFT WING


MODEL DESCRIPTION
Dimensions are that of a research subsonic aircraft wing. The
chord length at the free end is 0.8m and at the fixed end is
1.8m while the length of the wing is 15m.

Physical model of subsonic aircraft


wing

Finite element model of subsonic aircraft


Analyses are performed in this study by using a finite element model of the
aircraft wing. The model was developed in ANSYS 10.0; it has 47210
element, 74422 nodes and 3 layers

Layer stacking sequence of laminated Composite


structure (subsonic wing)
Each thickness of the layer in different spatial locations are
treated as to reduce twist angle parameter.

Finite element model applying


boundary conditions
The wing is treated as cantilevered shell. That is fixed at
one end ( i.e. all DOF) and free at the other end, as
shown in the figure

MATERIAL PROPERTIES:
The material properties used throughout this study are shown below.
These properties are for a carbon/epoxy and material Aluminum Alloy
are:
1. Material Properties (Aluminum Alloy)

Material used= Aluminum Alloy


Youngs Modulus = 73 GPa
Poisson's Ratio = 0.3
2. Material Properties (Carbon- epoxy)

Material used= Carbon- epoxy


Youngs Modulus = 140 GPa
Poisson's Ratio = 0.4

Results &
Discussions

Various results presented in following pictures


show the structural characteristics of the
aircraft wing

Wing with self load or acceleration due to gravity


Model fixed at the base (assumption is blade is
attached to the hub)

Gravity load of 9.8 m/s2 is applied at


the wing tip.

Load acting on x-axis

Nodal solution for Strain


energy

Load acting on y-axis

Nodal solution for stress on xaxis

CONCLUSION

Aircraft wing model as per the plan is made in the FEA and the
model is subjected to various loading. The loading given by the
self weight or due to acceleration due to gravity was discussed
and the deflection over has been calculated.

The wing model is severely affected by the loads on along


wing direction, across wing direction, vertical direction.
Moreover the combined loading is the real case.

An individual loading for example the load only on X direction


and its deflection in X, Y and Z directions, also the stress
acting on X, Y, and Z directions are found.

Von misses stress is calculated in order to know the


maximum stress levels and minimum stress levels on
the wing. The above mentioned results are found for
the combined loading also. Their differences are shown
clearly with the contour deflections, stress levels. The
deflection and stress levels are shown from minimum
to maximum in the color contours.

This model can be considered with twist for the various


aero foil shapes in future. For example NACA 4415 aero
foil or the aero foil with different thickness can be
considered.

References:
[1] Kaihong Wang, 2004 Vibration Analysis OF Cracked Composite Bending Torsion Beams For Damage
Diagnosis

[2] Jan Stegmmann, 2005 Analysis and Optimization Of Laminated Composite Shell Structure
www.ime.auc.dk/people/employees/is/docs/stegmann_PhDThesis.pdf

[3] Hiro Miura, 2001 Development of a Composite Tailoring Technique for Airplane Wing NASA research
center.

[4] Guo, S.J. Bannerjee, J.R. Cheung and C.W, 2002The Effect of Laminate Lay-Up on the Flutter Speed of
Composite Wings thesis on City University, London, UK

[5] Aditi Chattopadhyay , 2005 Development of a Composite Tailoring Procedure for Airplane Wing NASA
research center

[6] Shyama Kumari and P.K Sinha, 2002 Finite Element Analysis of Composite Wing TJoints Journal of
Reinforced Plastics and Composites 2002; 21; 1561

[7] Alastair F. Johnson and Nathalie Pentecote, 2005 Modeling Impact Damage In Double-Walled Composite
StructuresVIII International Conference.

[8] Boyang Liu, 2001, Two-Level Optimization of Composite Wing Structure Based on Panel Genetic
Optimization

[9] G. R. Benini, E. M. Belo and F. D. Marques, 2004 Numerical Model for the Simulation of Fixed Wings
Aeroelastic Response Journal of the Brazil Society of Mechanical Science and Engineering, April-June 2004,
Vol. XXVI, No. 2 / 129

[10] Seong-Wook Hong, Byung-Sik Kang and Joong-Youn Park, 2003 Dynamic Analysis of Bending-Torsion
Coupled Beam Structures Using Exact Dynamic Elements

You might also like