Scribd
Upload
722 views

Buckling Analysis: Concept & Procedure

- Buckling is a failure mode where a structural member fails under compressive stresses at a load lower than its ultimate compressive strength, due to elastic instability. It can occur stably or unstably. - Buckling analysis can be performed using either the eigenvalue or nonlinear method in ANSYS. Eigenvalue analysis predicts theoretical buckling strength but may overestimate, while nonlinear analysis is more accurate by including large deflections. - The document outlines the step-by-step procedure for performing both eigenvalue and nonlinear buckling analyses in ANSYS, including applying constraints and loads, solving the model, and viewing results like buckling loads and mode shapes.

Uploaded by

Deepak Chachra
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
722 views

Buckling Analysis: Concept & Procedure

- Buckling is a failure mode where a structural member fails under compressive stresses at a load lower than its ultimate compressive strength, due to elastic instability. It can occur stably or unstably. - Buckling analysis can be performed using either the eigenvalue or nonlinear method in ANSYS. Eigenvalue analysis predicts theoretical buckling strength but may overestimate, while nonlinear analysis is more accurate by including large deflections. - The document outlines the step-by-step procedure for performing both eigenvalue and nonlinear buckling analyses in ANSYS, including applying constraints and loads, solving the model, and viewing results like buckling loads and mode shapes.

Uploaded by

Deepak Chachra
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 20

Buckling Analysis

Concept & Procedure

What is Buckling ?
In engineering, buckling is a failure mode characterised by a sudden failure of a structural member that is subjected to high compressive stresses where the actual compressive stresses at failure are smaller than the ultimate compressive stresses that the material is capable of withstanding. This mode of failure is also described as failure due to elastic instability.

Buckling proceeds in manner which may be either: Stable: in which case displacements increase in a controlled fashion as loads are increased, ie. the structure's ability to sustain loads is maintained, or Unstable: in which case deformations increase instantaneously, the load carrying capacity nose- dives and the structure collapses catastrophically

Bending & Buckling


Buckling and bending are similar in that they both involve bending moments. In bending these moments are substantially independent of the resulting deflections, whereas in buckling the moments and deflections are mutually inter-dependent - so moments, deflections and stresses are not proportional to loads.

If buckling deflections become too large then the structure fails this is a geometric consideration, completely divorced from any material strength consideration. If a component or part thereof is prone to buckling then its design must satisfy both strength and buckling safety constraints.

Definitions
The behaviour of a buckling system is reflected in the shape of its loaddisplacement curve - referred to as the equilibrium path. The lateral or 'outof-plane' displacement, , is preferred to the load displacement, q, in this context since it is more descriptive of buckling.

Nothing is visible when the load on a column first increases from zero - the column is stable, there is no buckling, and no out- of- plane displacement. The P- equilibrium path is thus characterised by a vertical segment the primary path - which lasts until the increasing load reaches the critical Euler load Pc = 2 EImin/L2 a constant characteristic of the column When the load reaches the Euler load, buckling suddenly takes place without any further load increase, and lateral deflections grow instanteously in either equally probable direction. After buckling therefore, the equilibrium path bifurcates into two symmetric secondary paths as illustrated. Clearly the critical Euler load limits the column's safe load capacity.

Analysis Procedure in Ansys


There are two primary means to perform a buckling analysis: Eigenvalue Eigenvalue buckling analysis predicts the theoretical buckling strength of an ideal elastic structure. It computes the structural eigenvalues for the given system loading and constraints. However, in real-life, structural imperfections and nonlinearities prevent most real-world structures from reaching their eigenvalue predicted buckling strength; ie. it over-predicts the expected buckling loads. This method is not recommended for accurate, real-world buckling prediction analysis. Nonlinear Nonlinear buckling analysis is more accurate than eigenvalue analysis because it employs non-linear, large-deflection, static analysis to predict buckling loads. Its mode of operation is very simple: it gradually increases the applied load until a load level is found whereby the structure becomes unstable (ie. suddenly a very small increase in the load will cause very large deflections).

Eigenvalue Buckling Analysis


Consider a simple problem a steel beam with a 10 mm X 10 mm cross section, rigidly constrained at the bottom. The required load to cause buckling, applied at the top-center of the beam, can be calculated. Steps involved : 1. Define Analysis Type
Solution ANTYPE,0 > Analysis Type > New Analysis > Static

2.

Activate prestress effects


To perform an eigenvalue buckling analysis, prestress effects must be activated. In the following window, change the [SSTIF][PSTRES] item to 'Prestress ON', which ensures the stress stiffness matrix is calculated. This is required in eigenvalue buckling analysis

Eigenvalue Buckling Analysis

Eigenvalue Buckling Analysis


Apply Constraints

Solution > Define Loads > Apply > Structural > Displacement > On Keypoints The eignenvalue solver uses a unit force to determine the necessary buckling load. Applying a load other than 1 will scale the answer by a factor of the load. Apply a vertical (FY) point load of -1 N to the top of the beam (keypoint 2). Fix Keypoint 1 (ie all DOF constrained). The applied loads and constraints should now appear as shown in the figure below:

Eigenvalue Buckling Analysis


Solve the System Solution > Solve > Current LS SOLVE Exit the Solution processor Close the solution menu and click FINISH at the bottom of the Main Menu. Normally at this point you enter the postprocessing phase. However, with a buckling analysis you must re-enter the solution phase and specify the buckling analysis. Be sure to close the solution menu and re-enter it or the buckling analysis may not function properly. Define Analysis Type Solution > Analysis Type > New Analysis > Eigen Buckling ANTYPE,1

Eigenvalue Buckling Analysis


Specify Buckling Analysis Options Select Solution > Analysis Type > Analysis Options Complete the window which appears, as shown below. Select 'Block Lanczos' as an extraction method and extract 1 mode. The 'Block Lanczos' method is used for large symmetric eigenvalue problems and uses the sparse matrix solver. The 'Subspace' method could also be used, however it tends to converge slower as it is a more robust solver. In more complex analyses the Block Lanczos method may not be adequate and the Subspace method would have to be used.

Eigenvalue Buckling Analysis


Solve the System Solution > Solve > Current LS SOLVE

View the Buckling Load To display the minimum load required to buckle the beam select General Postproc > List Results > Detailed Summary. The value listed under 'TIME/FREQ' is the load (41,123), which is in Newtons for this example. If more than one mode was selected in the steps above, the corresponding loads would be listed here as well.

Eigenvalue Buckling Analysis


Display the Mode Shape
Select General Postproc > Plot Results > Deformed Shape

Non-Linear Buckling Analysis


Define Analysis Type Solution > New Analysis > Static ANTYPE,0 Set Solution Controls Select Solution > Analysis Type > Sol'n Control...

Non-Linear Buckling Analysis


Ensure the following selections are made under the 'Basic' tab (as shown above)
Ensure Large Static Displacements are permitted (this will include the effects of large deflection in the results) Ensure Automatic time stepping is on. Automatic time stepping allows ANSYS to determine appropriate sizes to break the load steps into. Decreasing the step size usually ensures better accuracy, however, this takes time. The Automatic Time Step feature will determine an appropriate balance. This feature also activates the ANSYS bisection feature which will allow recovery if convergence fails. Enter 20 as the number of substeps. This will set the initial substep to 1/20 th of the total load. Enter a maximum number of substeps of 1000. This stops the program if the solution does not converge after 1000 steps. Enter a minimum number of substeps of 1. Ensure all solution items are writen to a results file.

Non-Linear Buckling Analysis


Ensure the following selection is made under the 'Nonlinear' tab (as shown below) Ensure Line Search is 'On'. This option is used to help the Newton-Raphson solver converge. Ensure Maximum Number of Iterations is set to 1000

Non-Linear Buckling Analysis


Apply Constraints Apply Loads
Solution > Define Loads > Apply > Structural > Displacement > On Keypoints Fix Keypoint 1 (ie all DOFs constrained). Solution > Define Loads > Apply > Structural > Force/Moment > On Keypoints Place a -50,000 N load in the FY direction on the top of the beam (Keypoint 2). Also apply a -250 N load in the FX direction on Keypoint 2. This horizontal load will persuade the beam to buckle at the minimum buckling load. The model should now look like the window shown below.

Non-Linear Buckling Analysis


Solve the System Solution > Solve > Current LS The following will appear on your screen for NonLinear Analyses

ERJ 170/175 Side stay Analysis


Eigen-Buckling Mode Shapes

First Mode

Second Mode

ERJ 170/175 Side stay Analysis


Non-Linear Buckling Analysis
Node location for the plot
787.5 KN

Critical buckling load

THANKS !!

You might also like