Scribd
Upload
347 views

Cranes: OSHA Office of Training & Education 1

The document discusses crane safety hazards and regulations. It identifies major causes of crane accidents as unstable loads, lack of communication between operators and others on site, lack of training, and inadequate maintenance or inspection. It provides guidance on proper crane operation, inspection, and maintenance to prevent accidents. Key safety areas covered include avoiding power lines, ensuring stable ground conditions, using signals for communication, inspecting rigging equipment, and requiring operator training.

Uploaded by

unbridledsuccess
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
347 views

Cranes: OSHA Office of Training & Education 1

The document discusses crane safety hazards and regulations. It identifies major causes of crane accidents as unstable loads, lack of communication between operators and others on site, lack of training, and inadequate maintenance or inspection. It provides guidance on proper crane operation, inspection, and maintenance to prevent accidents. Key safety areas covered include avoiding power lines, ensuring stable ground conditions, using signals for communication, inspecting rigging equipment, and requiring operator training.

Uploaded by

unbridledsuccess
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 38

Cranes

OSHA Office of Training & Education

Contact with power lines Overturns Falls

Mechanical failures
OSHA Office of Training & Education 2

Instability unsecured load, load capacity

exceeded, or ground not level or too soft Lack of communication - the point of operation is a distance from the crane operator or not in full view of the operator Lack of training Inadequate maintenance or inspection

OSHA Office of Training & Education

Operators
Persons at Crane Site

OSHA Office of Training & Education

Crane Consists of a rotating structure for lifting and lowering horizontally on rubber tires or crawler treads Hoist - Used to lift and lower load. Boom An inclined spar, strut, or other long member supporting the hoisting tackle Boom stops A device used to limit the angle of the boom at its highest position Brake To slow or stop motion by friction or power Block Sheaves or grooved pulleys in a frame with hook, eye and strap Jib Extension attached to the boom point to provide added boom length for lifting specified loads.

OSHA Office of Training & Education

OSHA Office of Training & Education

Mobile Hydraulic Overhead Gantry Tower

OSHA Office of Training & Education

Crane Hazards

Improper load rating Excessive speeds No hand signals Inadequate inspection and maintenance Unguarded parts Unguarded swing radius

Working too close to power lines Improper exhaust system Shattered windows No steps/guardrails walkways No boom angle indicator Not using outriggers
8

OSHA Office of Training & Education

Level the crane and ensure support surface is firm and able to support the load Contact power line owners and determine precautions. Know the location and voltage of overhead power lines. Know the basic crane capacities, limitations, and job site restrictions, such as the location of power lines, unstable soil, or high winds. Make other personnel aware of hoisting activities. Barricade areas within swing radius. Ensure proper maintenance and inspections. Determine safe areas to store materials and place machinery.

OSHA Office of Training & Education

Competent Person
The competent person must inspect all machinery and equipment prior to each use, and during use, to make sure it is in safe operating condition. If it needs fixing, take it out of service and dont use it until it is fixed

Broken Track

OSHA Office of Training & Education

10

Load Capacity - Speed - Warnings

Make sure the crane operator can see the: Rated Load Capacities Operating Speeds Special Hazard Warning or Instruction Load Rating Chart
OSHA Office of Training & Education 11

Refer to shipping ticket or other documentation Ensure lift calculations are correct Ensure load is within load chart rating for boom length and load radius of crane Crane is rated by the maximum weight it will lift at a minimum radius and minimum boom length the further from its centerpoint, the less it will lift

OSHA Office of Training & Education

12

Not level Wind Side loads On its wheels Lifting over the side Use of extensions, jibs and other attachments

Limits of wire rope, slings and lifting devices

OSHA Office of Training & Education

13

Center of Gravity Leverage Stability Structural Integrity

OSHA Office of Training & Education

14

Will lift 60,000 pounds at 10 feet from the center pin of the crane
Based on level surface, no wind, and outriggers fully extended

At 25 feet from the center pin with an 80 foot boom, the capacity is only 14,950 pounds
At 74 feet from the center pin, the capacity is only 4,800 pounds

OSHA Office of Training & Education

15

Improper loads or speeds can result in the tipping of the crane


OSHA Office of Training & Education 16

Improper Load

OSHA Office of Training & Education

17

Improper Load

OSHA Office of Training & Education

18

Power Lines

Stay clear from power lines at least 10 feet

OSHA Office of Training & Education

19

Hand Signals
An illustration of the signals must be posted at the job site

OSHA Office of Training & Education

20

Guard Moving Parts

Unguarded Chain Drive

Guard moving parts such as gears or belts


OSHA Office of Training & Education 21

Swing Radius

Stay out of the swing radius of the crane Make sure there are barrier guards showing swing radius
OSHA Office of Training & Education 22

Operator Visibility
Broken Window

Make sure broken windows or other obstructions do not prevent the operator from seeing
OSHA Office of Training & Education 23

Ladders

Ladder

Use ladders to get to the upper portion of the cab


OSHA Office of Training & Education 24

Guardrails

Runways and steps need to have guardrails, handholds and slip resistant surfaces
OSHA Office of Training & Education 25

Suspended Loads

Dont stand under suspended loads


OSHA Office of Training & Education 26

Boom Angle Indicator

A boom angle indicator must be on the crane


OSHA Office of Training & Education 27

Supporting Surface

Cranes must be on a firm supporting surface and level within 1 percent


OSHA Office of Training & Education 28

Sheaves

The grooves must be smooth and free from surface defects which could cause rope damage
OSHA Office of Training & Education 29

Rigging Equipment Slings


Types of slings include alloy steel chain, wire rope, metal mesh, natural or synthetic fiber rope, and synthetic web.

Chain

Wire rope

Metal mesh

Synthetic

OSHA Office of Training & Education

30

Annual Inspections
Inspection of the hoisting machinery must be made by a competent person The employer must maintain a record of these inspections

Crane wasnt inspected and tipped over

OSHA Office of Training & Education

31

Correct air pressure and no leaks Tires properly inflated Clearance for tail swing Wire rope wear Physical damage to crane Loose or missing hardware, nuts, or bolts Fluid leaks

OSHA Office of Training & Education

32

Remove From Service

Immediately remove damaged or defective slings from service


OSHA Office of Training & Education 33

Damaged wire rope

Crushed Rope Broken Strands

Damaged wire rope must be taken out of service

OSHA Office of Training & Education

34

Worn Part

OSHA Office of Training & Education

35

Tire Inspections
Conduct regular inspections of tires for excessive wear or damage

OSHA Office of Training & Education

36

Operators:

must qualify on specific crane type


Must include on-the-job training

Supervisor / competent person

OSHA Office of Training & Education

37

Summary
An unstable load, lack of communication, lack of training, and inadequate maintenance or inspection are major contributors to crane accidents. Operators or others working in the area can be victims to struck by" and "caught in" injuries. Contact with power lines causes many accidents. A competent person must inspect a crane regularly to insure it is in proper order. Planning and training reduces accidents.

OSHA Office of Training & Education

38

You might also like