Scribd
Upload
36 views

ENGR 107 - Introduction To Engineering: Estimation, Accuracy and Precision, and Significant Figures

This document discusses key concepts in engineering measurements and significant figures, including: 1) Estimation is used when information is insufficient or uncertain, or problems are too difficult to solve exactly. Exercises provide examples of estimating volume, density, and number of tiles to the nearest value. 2) Accuracy refers to the closeness of a measurement to the true value, while precision refers to the consistency of repeated measurements under the same conditions. 3) Significant figures are used to numerically express the accuracy of measurements, with rules for rounding, multiplication, division, addition, and subtraction of values with different significant figures.

Uploaded by

vlsipranati
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
36 views

ENGR 107 - Introduction To Engineering: Estimation, Accuracy and Precision, and Significant Figures

This document discusses key concepts in engineering measurements and significant figures, including: 1) Estimation is used when information is insufficient or uncertain, or problems are too difficult to solve exactly. Exercises provide examples of estimating volume, density, and number of tiles to the nearest value. 2) Accuracy refers to the closeness of a measurement to the true value, while precision refers to the consistency of repeated measurements under the same conditions. 3) Significant figures are used to numerically express the accuracy of measurements, with rules for rounding, multiplication, division, addition, and subtraction of values with different significant figures.

Uploaded by

vlsipranati
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 32

ENGR 107 Introduction to Engineering

Estimation, Accuracy and Precision, and Significant Figures


(Lecture #3)

ENGR 107 - Introduction to Engineering

Estimation

ENGR 107 - Introduction to Engineering

Estimation
A rough calculation, often using incomplete or uncertain data, that is still close enough to be useful.
Definition courtesy of Wikipedia

Synonym: approximation

ENGR 107 - Introduction to Engineering

Estimation

Estimations are used when


Insufficient information is available Available information is uncertain

Problem is too difficult to solve analytically


Problem is impossible to solve using available analysis tools. An inexact result is useful A range (i.e. upper and lower bounds) is useful ENGR 107 - Introduction to Engineering
4

Estimations are used when


Estimation
Exercise:

Calculate the volume of a box to the nearest cubic meter.


The dimensions of the box are: W = 3.75 m L = 1.675 m H = 2.35 m
ENGR 107 - Introduction to Engineering 5

Estimation
Exercise: Calculate the density of a material to the nearest kg / m3.
The mass and volume of the material are: Mass = 489.54 kg Volume = 7.5 m3
ENGR 107 - Introduction to Engineering 6

Estimation
Exercise: Determine the number of tiles, to the nearest integer number, needed to tile a wall.
Dimensions of the tile: 4.5 in. x 4.5 in. Dimensions of the wall: 7.5 ft. x 11 ft.

ENGR 107 - Introduction to Engineering

Estimation

Calculate the volume of the classroom, using your height as a measuring stick.

ENGR 107 - Introduction to Engineering

Accuracy and Precision

ENGR 107 - Introduction to Engineering

Accuracy and Precision

In measurements, accuracy and precision have different meanings and cannot be used interchangeably.

ENGR 107 - Introduction to Engineering

10

Accuracy

The degree of closeness of a measurement to the actual or true value.


Definition courtesy of Wikipedia

ENGR 107 - Introduction to Engineering

11

Precision
The degree to which repeated measurements under unchanged conditions show the same results.
Definition courtesy of Wikipedia

Also called reproducibility or repeatability.

ENGR 107 - Introduction to Engineering

12

Accuracy vs Precision
Accurate

ENGR 107 - Introduction to Engineering

13

Accuracy vs Precision
Precise

ENGR 107 - Introduction to Engineering

14

Accuracy vs Precision
Accurate and Precise

ENGR 107 - Introduction to Engineering

15

Accuracy vs Precision

ENGR 107 - Introduction to Engineering

16

Measurements

ENGR 107 - Introduction to Engineering

17

Measurements

Engineers must be able to measure physical quantities and express these measurements in numerical form. Engineers must have confidence that the measurements and subsequent calculations and decisions made based on the measurements are reasonable.
ENGR 107 - Introduction to Engineering 18

Measurements

Any physical measurement that is not a countable number will be approximate. Errors are likely to be present regardless of the precautions used when making the measurements. Significant digits are used to express, numerically, the accuracy of a measurement.
ENGR 107 - Introduction to Engineering 19

Measurement Estimation

There is a finite accuracy to which every engineering measurement can be made. There is a limited number of significant digits that can be included in the numerical representation of a measurement. The engineer must estimate the measurement between the smallest graduations on the instrument.
ENGR 107 - Introduction to Engineering 20

Measurement Estimation

ENGR 107 - Introduction to Engineering

21

Errors

ENGR 107 - Introduction to Engineering

22

Errors

Systematic

A bias in the measurement leading to the mean of a set of measurements differing significantly from the expected value. Can be identified and eliminated

Random

An error in the measurement leading to inconsistent values for repeated measurements of the same attribute. Caused by unpredictable fluctuations in the readings of the measurement equipment, in the environment, etc.

Cannot be eliminated
ENGR 107 - Introduction to Engineering 23

Significant Digits

ENGR 107 - Introduction to Engineering

24

Numerical Values

For numbers less than one, a zero is written in front of the decimal point. A space, not a comma, is used to divide numbers of three orders of magnitude or more.

For very large or very small numbers, use scientific notation to reduce the unwieldy nature of these numbers.
ENGR 107 - Introduction to Engineering 25

Significant Digits

A significant digit, or significant figure, is defined as any digit used in writing a number, except those zeros that are used only for location of the decimal point or those zeros that do not have any nonzero digit to their left.

ENGR 107 - Introduction to Engineering

26

Significant Digits

Numbers 10 or larger that are not written in scientific notation and that are not counts (exact values) can cause difficulties in interpretation when zeros are present. If uncertainty results from using standard decimal notation, use scientific notation so that the reader will clearly understand your intent.
ENGR 107 - Introduction to Engineering 27

Significant Digits

ENGR 107 - Introduction to Engineering

28

Significant Digits

Rounding:

Increase the last digit retained by 1 if the first digit dropped is greater than 5.

ENGR 107 - Introduction to Engineering

29

Significant Digits

Multiplication and Division: The product or quotient should contain the same number of significant digits as the number with the fewest significant digits.

ENGR 107 - Introduction to Engineering

30

Significant Digits

Addition and Subtraction: The sum or difference should include significant digits only as far to the right as in the least precise number.

ENGR 107 - Introduction to Engineering

31

Arithmetic and Significant Digits

In calculator or computer applications it is not practical to perform intermediate rounding (i.e. between arithmetic operations). It is normal practice to perform the entire calculation and then report a reasonable number of significant figures.

The number of significant digits in the result cannot exceed that in the value with the fewest significant digits.
The result cannot be more precise than any of the values 107 - Introduction to Engineering 32 included in ENGR the calculation.

You might also like