IPv6 Addressing

John Rullan Cisco Certified Instructor Trainer Thomas A. Edison CTE HS Stephen Lynch Network Architect, CCIE #36243 ABS Technology Architects

 128-bit hexadecimal format (0-9, A-F) Uses 16-bit hexadecimal number fields separated by colons (:) Every 4-hexadecimal digits are equivalent to 16-bits. Consists of 8 hextets/quartets which is the equivalent to 16-bits

per-hextet.

2001:0DB8:0001:5270:0127:00AB:CAFE:0E1F /64
- 2001 in hexadecimal is 0010 0000 0000 0001 in binary

2013 Cisco and/or its affiliates. All rights reserved.

Cisco Public

 The Site Prefix or Global Routing Prefix is the first 3 hextets or

48-bits of the address. It is assigned by the service provider.

The Site Topology or Subnet ID Is the 4th hextet of the address.
The Interface ID is the last 4 hextets or 64-bits of the address. It

can be manually or dynamically assigned using the EUI-64 command. (Extended Unique Identifier)

2013 Cisco and/or its affiliates. All rights reserved.

Cisco Public

 First 3 bits are fixed at 001 or 200::/12 (IANA Global Routing

Number)
Bits 16-24 identifies the Regional Registry:
- AfriNIC, APNIC, LACNIC, RIPE NCC and ARIN

2001:0000::/23 IANA 2001:0200::/23 APNIC (Asia/Pacific Region) 2001:0400::/23 ARIN (North America Region) 2001:0600::/23 RIPE (Europe, Middle East and Central Asia)

2013 Cisco and/or its affiliates. All rights reserved.

Cisco Public

 Remaining 8-bits up to /32 identifies the ISP.

The 3rd hextet represents the Site/Customer Identifier.

The 4th hextet represent the Site Topology/Subnet ID.

- Allows 65,536 subnets with 18,446,744,073,709,551,616 (18 quintillion) for each subnet. - Not part of the host address field.

2013 Cisco and/or its affiliates. All rights reserved.

Cisco Public

 The Interface ID are the remaining 64-bits of the address. Can be manually configured or dynamically by using the EUI-64

(Extended Unique Identifier).

The EUI-64 command uses the device 48-bits MAC Address and

convert it into 64-bits by adding FF:FE in the middle of the address.

The first (network) and last (broadcast) address may be assigned

to an interface. An interface may contain more than one IPv6 address.

There are no broadcast addresses, multicast is used instead.
2013 Cisco and/or its affiliates. All rights reserved. Cisco Public 6

 IPv6 uses the same method as IPv4 to subnet their addresses. /127 gives you 2 addresses. /124 gives you 16 addresses /120 gives you 256 addresses The first address in a network consists of all 0's and the last

address consists of all F's.

Its recommended for simplicity and design purposes to use /64

everywhere. Using anything less than /64 could potentially break IPv6 features and cause increased design complexity.

2013 Cisco and/or its affiliates. All rights reserved.

Cisco Public

 Leading 0s (zeroes) in any 16-bit section can be omitted.

Address before omission: 2001:0DB8:0001:5270:0127:00AB:CAFE:0E1F /64 Address after omission: 2001:DB8:1:5270:127:AB:CAFE:E1F /64
This rule applies only to leading 0s; if trailing 0s are omitted, the

address would be vague.

2013 Cisco and/or its affiliates. All rights reserved.

Cisco Public

 A Double Colons or Compressing Zeroes can be used to shorten

an IPv6 address when one or more hextets consist of all 0s.

Double Colons can only be used to compress a single contiguous

16-bits blocks. You cannot use double colons to include part of a block.

Double Colons can only be used once in an address, if it's used

more than once the address could be ambiguous

2013 Cisco and/or its affiliates. All rights reserved.

Cisco Public

 Unicast Address
Uniquely identifies a single interface on an IPv6 device. A packet sent to a unicast address destination travels from one host to the destination host. An interface may have more than one IPv6 address or an IPv6 and an IPv4 addresses which is referred as "Double Stack". When mistakes are made on Entering an address to the IPv6 interface, the user must issue the no ipv6 address command before entering the correct one or the address will remain on the interface. (see figure)
2013 Cisco and/or its affiliates. All rights reserved. Cisco Public 10

 Multicast Address
A Multicast address identifies a group of interfaces. All Multicast address are identified by their reserved address range FF00::0/8 A packet sent to a multicast address is delivered to all devices that are identified by that address.
Protocol OSPF (Router) OSPF (DR/BDR) RIPv2 EIGRP IPv4 Multicast 224.0.0.5 224.0.0.6 224.0.0.9 224.0.0.10 IPv6 Multicast FF02::5 FF02::6 FF02::9 FF02::A

Anycast Address
A unicast address can be assigned to several interfaces/devices.
A packet sent to an Anycast address goes only to the nearest member of the group, according to the routing protocols measures of distance. Anycast is described as a cross between a Unicast and Multicast. The difference between an Anycast and Multicast is that in Anycast packet is only delivered to a single device, while Multicast send it to multiple devices.
2013 Cisco and/or its affiliates. All rights reserved. Cisco Public 11

Link-Local Address
Link-Local address are designed for use on a single local link.

Link-Local address are automatically configured on all interfaces.

The prefix used for a Link-Local address is FE80::X/10. Routers do not forward packet with a destination and source address containing a link-local address.

Loopback Address
Similar function to IPv4 127.0.0.1 address The Loopback address is 0:0:0:0:0:0:0:1 or may be simplify by using double colons as ::1.

It is used by a device to send a packet to itself

Representation Preferred No Leading 0s Compresses
2013 Cisco and/or its affiliates. All rights reserved.

IPv6 Loopback Address 0000:0000:0000:0000:0000:0000:0000:0001 0:0:0:0:0:0:0:1 ::1

Cisco Public 12

 128-bits address containing

32-bits addressing scheme

global routing prefix, subnet ID and interface ID.

Uses a hexadecimal format

containing a host and a network portion.

Use binary format between 0

ranging from 0-9, A-F.

Maximum Transmission Unit

and 1.
Maximum Transmission Unit

up to 1280 bytes.
Network address and

up to 576 bytes.
Network address and

broadcasts address can be assigned to an interface or end device.

Native IPsec encryption

broadcasts address cannot be assigned to an interface or end device.

VPN technologies must be

used to encrypt IPv4 packets.

2013 Cisco and/or its affiliates. All rights reserved.

Cisco Public

13

Thank you.