Engineering Photovoltaic Systems I

Part I

Original Presentation by J. M. Pearce, 2006 Email: [email protected]

Outline Part I
What is a photovoltaic system
Cell, Module, and Array BOS
Structure Electronics

PV System Design Basics Hybrid Systems

The Cell, The Module and The Array

Balance of System (BOS)

The BOS typically contains;
Structures for mounting the PV arrays or modules Power conditioning equipment that massages and converts the do electricity to the proper form and magnitude required by an alternating current (ac) load. Sometimes also storage devices, such as batteries, for storing PV generated electricity during cloudy days and at night.

Three Types of Systems

Stand-alone systems - those systems which use photovoltaics technology only, and are not connected to a utility grid. Hybrid systems - those systems which use photovoltaics and some other form of energy, such as diesel generation or wind. Grid-tied systems - those systems which are connected to a utility grid.

Stand Alone PV System

Water pumping

Examples of Stand Alone PV Systems

PV panel on a water pump in Thailand

PV powers stock water pumps in remote locations in Wyoming

Examples of Stand Alone PV Systems

Communications facilities can be powered by solar technologies, even in remote, rugged terrain. Also, if a natural or human-caused disaster disables the utility grid, solar technologies can maintain power to critical operations

Examples of Stand Alone PV Systems

This exhibit, dubbed "Solar Independence", is a 4-kW system used for mobile emergency power. while the workhorse batteries that can store up to 51 kW-hrs of electricity are housed in a portable trailer behind the flag. The system is the largest mobile power unit ever built

Examples of Stand Alone PV Systems

Smiling child stands in front of Tibetan home that uses 20 W PV panel for electricity PV panel on rooftop of rural residence

Hybrid PV System

Examples of Hybrid PV Systems

Ranching the Sun project in Hawaii generates 175 kW of PVpower and 50 kW of wind power from the five Bergey 10 kW wind turbines

Examples of Hybrid PV Systems

A fleet of small turbines; PV panels in the foreground

Examples of Hybrid PV Systems

PV / diesel hybrid power system - 12 kW PV array, 20 kW diesel genset This system serves as the master site for the "top gun" Tactical Air Combat Training System (TACTS) on the U.S. Navy's Fallon Range.

Grid-Tied PV System

Examples of Grid Tied Systems

National Center for Appropriate Technology Headquarters

Examples of Grid Tied Systems

The world's largest residentia l PV project

Designing a PV System
1.

Determine the load (energy, not power)

You should think of the load as being supplied by the stored energy device, usually the battery, and of the photovoltaic system as a battery charger. Initial steps in the process include:

2. 3. 4.

Calculating the battery size, if one is needed Calculate the number of photovoltaic modules required Assessing the need for any back-up energy of flexibility for load growth Stand-Alone Photovoltaic Systems: A Handbook of Recommended Design Practices details the design of complete photovoltaic systems.

Determining Your Load

The appliances and devices (TV's, computers, lights, water pumps etc.) that consume electrical power are called loads. Important : examine your power consumption and reduce your power needs as much as possible. Make a list of the appliances and/or loads you are going to run from your solar electric system. Find out how much power each item consumes while operating.
Most appliances have a label on the back which lists the Wattage. Specification sheets, local appliance dealers, and the product manufacturers are other sources of information.

Determining your Loads II

Calculate your AC loads (and DC if necessary) List all AC loads, wattage and hours of use per week (Hrs/Wk). Multiply Watts by Hrs/Wk to get Watt-hours per week (WH/Wk). Add all the watt hours per week to determine AC Watt Hours Per Week. Divide by 1000 to get kW-hrs/week

Determining the Batteries

Decide how much storage you would like your battery bank to provide (you may need 0 if grid tied)
expressed as "days of autonomy" because it is based on the number of days you expect your system to provide power without receiving an input charge from the solar panels or the grid.

Also consider usage pattern and critical nature of your application. If you are installing a system for a weekend home, you might want to consider a larger battery bank because your system will have all week to charge and store energy. Alternatively, if you are adding a solar panel array as a supplement to a generator based system, your battery bank can be slightly undersized since the generator can be operated in needed for recharging.

Batteries II
Once you have determined your storage capacity, you are ready to consider the following key parameters:
Amp hours, temperature multiplier, battery size and number
daily Amp hours number of days of storage capacity ( typically 5 days no input )

To get Amp hours you need:

1. 2.

1 x 2 = A-hrs needed
Note: For grid tied inverter losses

Temperature Multiplier
Temp oF 80 F 70 F 60 F 50 F 40 F 30 F 20 F Temp oC 26.7 C 21.2 C 15.6 C 10.0 C 4.4 C -1.1 C -6.7 C Multiplier 1.00 1.04 1.11 1.19 1.30 1.40 1.59

Select the closest multiplier for the average ambient winter temperature your batteries will experience.

Determining Battery Size

Determine the discharge limit for the batteries ( between 0.2 - 0.8 )
Deep-cycle lead acid batteries should never be completely discharged, an acceptable discharge average is 50% or a discharge limit of 0.5

Divide A-hrs/week by discharge limit and multiply by temperature multiplier Then determine A-hrs of battery and # of batteries needed - Round off to the next highest number.
This is the number of batteries wired in parallel needed.

Total Number of Batteries Wired in Series

Divide system voltage ( typically 12, 24 or 48 ) by battery voltage.
This is the number of batteries wired in series needed.

Multiply the number of batteries in parallel by the number in series This is the total number of batteries needed.

Determining the Number of PV Modules

First find the Solar Irradiance in your area Irradiance is the amount of solar power striking a given area and is a measure of the intensity of the sunshine. PV engineers use units of Watts (or kiloWatts) per square meter (W/m2) for irradiance. For detailed Solar Radiation data available for your area in the US: http://rredc.nrel.gov/solar/old_data/nsrdb/

How Much Solar Irradiance Do You Get?

Solar Radiation
On any given day the solar radiation varies continuously from sunup to sundown and depends on cloud cover, sun position and content and turbidity of the atmosphere. The maximum irradiance is available at solar noon which is defined as the midpoint, in time, between sunrise and sunset. Insolation (now commonly referred as irradiation) differs from irradiance because of the inclusion of time. Insolation is the amount of solar energy received on a given area over time measured in kilowatt-hours per square meter squared (kW-hrs/m2) - this value is equivalent to "peak sun hours".

Peak Sun Hours

Peak sun hours is defined as the equivalent number of hours per day, with solar irradiance equaling 1,000 W/m2, that gives the same energy received from sunrise to sundown. Peak sun hours only make sense because PV panel power output is rated with a radiation level of 1,000W/m2. Many tables of solar data are often presented as an average daily value of peak sun hours (kW-hrs/m2) for each month.

Calculating Energy Output of a PV Array

Determine total A-hrs/day and increase by 20% for battery losses then divide by 1 sun hours to get total Amps needed for array Then divide your Amps by the Peak Amps produced by your solar module
You can determine peak amperage if you divide the module's wattage by the peak power point voltage

Determine the number of modules in each series string needed to supply necessary DC battery Voltage Then multiply the number (for A and for V) together to get the amount of power you need
P=IV [W]=[A]x[V]

Charge Controller
Charge controllers are included in most PV systems to protect the batteries from overcharge and/or excessive discharge. The minimum function of the controller is to disconnect the array when the battery is fully charged and keep the battery fully charged without damage. The charging routine is not the same for all batteries: a charge controller designed for lead-acid batteries should not be used to control NiCd batteries. Size by determining total Amp max for your array

Wiring
Selecting the correct size and type of wire will enhance the performance and reliability of your PV system. The size of the wire must be large enough to carry the maximum current expected without undue voltage losses. All wire has a certain amount of resistance to the flow of current. This resistance causes a drop in the voltage from the source to the load. Voltage drops cause inefficiencies, especially in low voltage systems ( 12V or less ). See wire size charts here: www.solarexpert.com/Photowiring.html

Inverters
For AC grid-tied systems you do not need a battery or charge controller if you do not need back up power just the inverter. The Inverter changes the DC current stored in the batteries or directly from your PV into usable AC current.
To size increase the Watts expected to be used by your AC loads running simultaneously by 20%

Books for Designing a PV System

Steven J. Strong and William G. Scheller, The Solar Electric House: Energy for the EnvironmentallyResponsive, Energy-Independent Home, by Chelsea Green Pub Co; 2nd edition, 1994. This book will help with the initial design and contacting a certified installer.

Books for the DIYer

If you want to do everything yourself also consider these resources:
Richard J. Komp, and John Perlin, Practical Photovoltaics: Electricity from Solar Cells, Aatec Pub., 3.1 edition, 2002. (A laymans treatment). Roger Messenger and Jerry Ventre, Photovoltaic Systems Engineering, CRC Press, 1999. (Comprehensive specialized engineering of PV systems).

Photovoltaics Design and Installation Manual

Photovoltaics: Design & Installation Manual by SEI Solar Energy International, 2004 A manual on how to design, install and maintain a photovoltaic (PV) system. This manual offers an overview of photovoltaic electricity, and a detailed description of PV system components, including PV modules, batteries, controllers and inverters. Electrical loads are also addressed, including lighting systems, refrigeration, water pumping, tools and appliances.

Solar Photovoltaics is the Future

Acknowledgements
This is the second in a series of presentations created for the solar energy community to assist in the dissemination of information about solar photovoltaics. This work was supported from a grant from the Pennsylvania State System of Higher Education. The author would like to acknowledge assistance in creation of this presentation from Heather Zielonka, Scott Horengic and Jennifer Rockage.