PART OF
Salus
Smart Home
SMART HOME THERMOSTAT
Quick Guide
Introduction
The EL600F Elypso is a ZigBee temperature controller for wireless control of a variety of devices, such as the
KL08RF wiring centre, mini TRV head, RX10RF boiler control module.
In order to control EL600F over the Internet or via the SALUS Premium Lite mobile app (ONLINE mode), it must be
installed together with the UGE600 or UG800 Internet gateways (sold separately). From the application level, it is
possible to pair EL600F with other system elements, e.g. Smart Plug SPE600, Smart Relay SR600 , Thermostatic
Radiator Valves (TRV’s) or other mentoned compatible devices. EL600F can be used locally without an Internet
connection (OFFLINE mode), with ZigBee 3.0 devices like TRV3RF and RX30RF.
Product Compliance
This product complies with the essential requirements and other relevant provisions of Directives 2014/53/EU
and 2015/863/EU. The full text of the EU Declaration of Conformity is available at the following internet address:
www.saluslegal.com.
2405-2480MHz, <14dBm
Safety Information
Use in accordance to national and EU regulations. Use the device as intended, keeping it in dry condition. Product
for indoor use only. Installation must be carried out by a qualified person in accordance to national and EU regula-
tions. Disconnect your equipment before cleaning it with a dry cloth.
Package content
1) EL600F Thermostat 6) USB cable - type C
2) Charging dock 7) 2 x M3x25mm
3) Wall plate 8) 2x M3 x 15mm
4) Mini wall plate 9) 2x wall plugs
5)User quick guide 10) double sided adhesive mounting plate
1
Before you start:
1 The EL600T Elypso Thermostat is partially charged, however,
we recommend you to fully charge the battery before use.
Connect the charger to USB Port type C which is at the back of
the charging dock to charge the device.
Charging to full battery level may take up to 24h.
2 Mounting: to mount the thermostat the accesories included can be used
(mounting screws and/or self adhesive tape).
For wall plate: Remove the backplate and mount it on the wall by using the screws provided. After that the
wall plate can be attached to it.
For mini wall plate: Use the screws provided and/or self adhesive plate in order to fix it on the wall.
After following the procedure for any of the wall plates the thermostat can be attached. Due to the built-in
magnet, thermostat can be safely fixed in place.
Please note:
The ideal position for thermostat mounting is
about 1.5 m above floor level and far from
150 cm
heating and cooling sources. The thermo-
stat should not be exposed to sunlight or any cm
20
extreme conditions like for example draft. m
in
2
Screen’s Icon Description
1
2
4
7
8 5
9
6
10
1. Push button 6. Temperature display
2. Rotating dial 7. Locked mode
3. Heat/Cool Mode indicator 8. Schedule settings
4. RF status 9. Mode setting/Optimum features
5. Battery status 10. Frost protection (Off mode)
3
COMPATIBILTY WITH OTHER SALUS CONTROLS DEVICES
The Elypso Thermostat can work in ONLINE or OFFLINE mode.
At first you need to decide in which mode your thermostat will work.
ONLINE MODE OFFLINE MODE
Universal Gateway is CONNECTED TO THE INTERNET. Universal Gateway is NOT CONNECTED TO THE IN-
You can configure and use all your devices with the Salus TERNET. You can use it with TRV3RF and RX30RF locally
Premium Lite App. (use Pairing menu to pair with them) without the Salus
Premium Lite app.
Cloud Cloud Cloud
LAN/WiFi LAN/WiFi LAN/WiFi
OR
ZigBee ZigBee ZigBee
UG600/UGE600 UG800
Cloud Cloud Cloud
LAN/WiFi LAN/WiFi LAN/WiFi
ZigBee ZigBee ZigBee
OR
Cloud Cloud Cloud
LAN/WiFi LAN/WiFi LAN/WiFi
ZigBee ZigBee ZigBee
Download the Salus Premium Lite App
on your iOS or Android device for remote
acces to your Salus equipment. UG600/UGE600 UG800
Cloud Cloud Cloud
LAN/WiFi LAN/WiFi LAN/WiFi
Cloud Cloud Cloud
ZigBee ZigBee ZigBee
LAN/WiFi LAN/WiFi LAN/WiFi
ZigBee ZigBee ZigBee
Compatible devices:
TRV TRV3RF
SR600* Super quiet TRV
Cloud Cloud Cloud
(Thermostatic Radiator Valve)
LAN/WiFi LAN/WiFi LAN/WiFi
ZigBee ZigBee ZigBee
Smart Relay (Thermostatic Radiator Valve)
with wireless communication
with wireless communication
SPE600* RX10RF RX30RF
Smart Plug receiver receiver
KL08RF
UG800 UG600/UGE600 Wiring Centre for 8-zone
Gateway Gateway underfloor heating (UFH)
4
Power up sequence
Please note:
For an easier installation, please make sure you have already added other devices to your ZigBee network, such
as Underfloor Heating Control Box (KL08RF) or Radiator heads (TRV’s) etc.
3 sec
1 2 3
To power the Thermostat
hold the top button for 3 Display will show all icons. Thermostat is powered up.
seconds.
5
Installation in ONLINE mode
In order to proceed with the installation in online mode, the bellow steps must be followed:
This product must be used with the SALUS Premium Lite application on mobile or web
1 by accessing the following link: eu.premium.salusconnect.io or by scanning the QR code:
2
3 4
Make sure that the thermostat Press the three-line icon on the Select Equipment.
is powered up and RF signal top right corner.
indicator is blinking
6
5 6 7
From the drop-down menu, From the Groups tab, select Scan for equipment.
select All equipment. Add new equipment.
8 9 10
Tick the box to select
The app will scan for devices. Connect equipment.
EL600T Room Thermostat.
11 12 13
Name your equipment. Select Finish to get back to the Thermostat has been added to
dashboard view. dashboard.
7
Factory Reset
1 5 sec 2 3
Rotate the dial until Fr
Push and hold the button
command (Factory reset) Push the button to select.
for 5 seconds.
appears.
4 5 6
Rotate the dial until YES Factory reset has been
Push the button to confirm.
appears on the screen. initiated.
8
Thermostat Commands & Functions
Command Function
Auto Mode (AU): Automatically adjusts the temperature based on
pre-set schedules or sensor readings to maintain the desired comfort.
Manual Mode (M): Allows you to manually set and control the
temperature without automatic adjustments, giving you full control
until you choose to change it.
OFF: Turns off the heating and cooling functions of the thermostat
while keeping the device powered on.
Shut down (Sd): Puts the thermostat into a low-power state, turning
off active heating function and minimizing energy consumption.
Factory reset (Fr): Restores the thermostat to its original factory
settings, erasing all custom configurations, schedules, and paired
device connections.
Radio Frequency Indicator (rF): Shows the strength of the RF
connection.
Pairing mode (P): Thermostat activates the pairing mode.
10
HEAD OFFICE
SALUS Controls SALUS Controls GmbH,
Units 8-10, Northfield Business Dieselstrasse 34,
Park, Forge Way, 63165 Mühlheim am Main,
Parkgate, Rotherham, Germany
S60 1SD, United Kingdom
Email: [email protected]
www.saluscontrols.com
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS Controls plc
reserves the right to change specifitions, design and materials of products listed in
this brochure without prior notice.
V02
11/2024
