Scribd
Upload
424 views

Cathodic Protection

The document discusses cathodic protection for underground pipes and storage tanks in power generation plants. It covers corrosion processes, principles of cathodic protection using galvanic anodes or impressed current systems, and design/testing requirements. Proper planning, installation, and ongoing monitoring are necessary to ensure cathodic protection systems effectively prevent corrosion and extend the lifespan of protected structures.

Uploaded by

sjaveeds2003
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
424 views

Cathodic Protection

The document discusses cathodic protection for underground pipes and storage tanks in power generation plants. It covers corrosion processes, principles of cathodic protection using galvanic anodes or impressed current systems, and design/testing requirements. Proper planning, installation, and ongoing monitoring are necessary to ensure cathodic protection systems effectively prevent corrosion and extend the lifespan of protected structures.

Uploaded by

sjaveeds2003
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 68

Cathodic Protection Use On Tank Bottoms & Underground Piping In Power Generation Plants

PG&E Office San Francisco January 18, 2007 Craig K. Meier Corrosion Control Incorporated

IEEE

PES

Corrosion process for tanks and piping Principles of cathodic protection Effects of coatings Cathodic protection design requirements Selecting the proper system Construction implementation issues Compliance testing Continued monitoring and maintenance

IEEE

PES

Energy

Ore

Mill Steel

IEEE

PES

IEEE

PES

Energy Steel Rust Corrosion

IEEE

PES

Conventional Current Flow Fe++ Iron ion eCathode Anode Electron flow H2O + 1/2O2 + 2e- 2OHFe Fe++ + 2e-

IEEE

PES

Rate of Corrosion
Soil Corrosivity
Resistivity pH Salts

Bi-metallic effect Mixed soils Differences in oxygen

IEEE

PES

Excavation Clay Pipe Corrosion Native Soil

Sand

IEEE

PES

Corrosion Current

Corrosion

Copper ground -200 mV

Bare steel pipe -500 mV

IEEE

PES

Coating flaw Steel pipe Corrosion Copper ground Coating

IEEE

PES

Tank floor Corrosion Corrosion Clay lump

Copper ground

IEEE

PES

IEEE

PES

Tank floor Corrosion

Concrete or asphalt

API recommends against the use of asphalt and concrete tank pads.
IEEE PES

IEEE

PES

Corrosion Losses
Will occur in all plants Rate of loss dependent on soil and materials used Coatings alone do not stop soil corrosion Care during construction can significantly reduce losses

IEEE

PES

Corrosion Control
Material selection Bedding Coatings Cathodic Protection

IEEE

PES

Coating

Coating flaw

Steel

Reduces amount of exposed metal Coatings are not perfect


IEEE PES

Cathodic Protection
Pipe Ground

Anode H2O + 1/2O2 + 2e- 2OHIEEE PES

Cathodic Protection
Galvanic Impressed Current

IEEE

PES

Galvanic Anode
Exothermic weld Pipe -500mV Magnesium anode

-1700mV

IEEE

PES

Galvanic Cathodic Protection


Galvanic anodes have a limited current output, 10 to 30 milliamperes per anode. Due to the limited current output, the use of galvanic anodes is limited to coated and electrically isolated underground piping and underground tanks.

IEEE

PES

Galvanic Cathodic Protection


Dielectric flange Coating Coating damage

Pipe Magnesium anode

IEEE

PES

Bare steel tank bottom Protects only outer floor Galvanic anode

IEEE

PES

Impressed Current
AC Power Rectifier

(+)

(-)

Structure

Anode

IEEE

PES

Impressed Current
Anode

Unit 1

Unit 2

Unit 3 Rectifier

IEEE

PES

IEEE

PES

Impressed Current
Tank

Rectifier

20

Anode IEEE PES

Impressed Current
Anodes produce high amounts of current, 1000 to 5000 milliamperes per anode. High current output allows protection of bare steel structures. Structures do not necessarily need to be electrically isolated.

IEEE

PES

New Power Plant Design


Involve corrosion engineer from the start Obtain site soil resistivitiy data Select piping materials Select coating types and quality control procedures Decide which structures require cathodic protection

IEEE

PES

Cathodic Protection Design - Piping


Soil resistivity data Clearly identify piping to receive cathodic protection Yard plan showing piping layout, isometric drawings are difficult to use Location of all risers Type of coating Responsibility of isolation gaskets Desired service life
IEEE PES

Cathodic Protection Design - Tanks


Site soil resistivity data Tank diameters and layout Equipment access Type of foundation Containment Monitoring capability Desired service life

IEEE

PES

Design Options
Design documents issued in construction plans Contract responsible for cathodic design

IEEE

PES

Design Submittal
Qualifications of person responsible for design, supervision during installation and testing
Can not mail order

Detailed calculations for each tank and pipeline showing current required, number of anodes, circuit resistance and life Material list providing descriptions, models and quantities Product data sheets Detailed installation plans not diagrams
IEEE PES

Implementation
The cathodic design submittals must be approved before construction of structures A site meeting must be held to discuss how the cathodic protection system will be installed, and special concerns during construction Mechanical and electrical foremen should be involved in cathodic discussions

IEEE

PES

Avoid Costly Mistakes


Grounding cables must be at least 12 inches from underground pipes Temporary pipe supports must be removed Piping must be inspected for coating quality and separation from grounding before burial

IEEE

PES

Grounded Pipeline
Pipe

Ground wire

Anode

IEEE

PES

Instrument

Dielectric gasket

Conduit

Anode IEEE PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

IEEE

PES

Shunt Ring terminals Tag


Anode

Test station

Pipeline Galvanic anode IEEE PES

IEEE

PES

Coating Pipe wall

Weld Coating Pipe wall Standard Weld Clip Post Hydro Weld

IEEE

PES

IEEE

PES

Rectifier

Tank bottom
12 sand

Liner Anode array Anode IEEE PES

Completed Before Testing


All pipe flanges connected and isolated Pipes back filled and cathodic protection is complete AC power to rectifier unit Storage tanks contain product Schedule for testing and training issued

IEEE

PES

Compliance Testing - Specialist


Inspect cathodic systems to ensure they are properly installed Test each dielectric flange for isolation Obtain native potentials on pipes and tanks Connect galvanic anodes at test stations and/or energize rectifier(s) Cathodic protection systems on isolated coated structures should operate at least 4 hours before testing Cathodic protection systems on bare steel or grounded structures must operate between 12 hours and 7 days before testing
IEEE PES

-.892

Set to DC volts Pipe

Reference cell Soil IEEE

6 PES

Galvanic Anode Current

Set to DC millivolts

Shunt

IEEE

PES

Impressed Current Rectifier Unit


Transformer adjustments Meters Breaker Volts Amps Shunt

Output lug IEEE

(-)

(+) PES

Meter

Potential plus gradient

Cell

Potential of steel

Impressed anode

Voltage gradient

IEEE

PES

Emeasured = Ptank + I R If the current is momentarily interrupted, I=O, then; Emeasured = Ptank + (O) (R) Instant Off potential

IEEE

PES

Cathodic Protection Criteria


Galvanic anodes
-850mV or more negative with anodes connected

Impressed current
-850mV or more negative instant-off -or 100mV polarization shift

IEEE

PES

100mV Polarization Criteria

-1104 On Instant off -692 Polarization 167 -525 Native

IEEE

PES

Compliance Report
Tabulated Data Narrative analysis of the data Compliance statement Calculated anode life Test procedures and instrumentation As-built drawings O&M Manual

IEEE

PES

O&M Manual
Test Procedures Instrument requirements Qualification requirements Frequency Criteria Trouble shooting Spare parts Wiring diagrams
PES

IEEE

Conclusions
Cathodic protection is viable and necessary to preserve power plant structures Proper planning and coordination are essential through out the design and construction phases, to ensure cathodic protection systems work properly Properly implemented and monitored cathodic protection will extend the service life of storage tanks and yard piping more than 30 years

IEEE

PES

Owner Monitoring & Maintenance


Record rectifier output levels monthly and compare output to target values Repair inoperable rectifiers within 30 days Inspect test stations and dielectric flanges every six (6) months for damage and removal Instruct maintenance staff to replace and test removed dielectric gaskets Annually, obtain potential measurements and ensure effective cathodic protection levels
IEEE PES

You might also like