Scribd
Upload
472 views

AGA3 1990 Algorithm

The document describes the AGA3 1990 algorithm for calculating gas flow measurements. The algorithm takes input parameters like pressure, temperature, compressibility and uses an iterative process to calculate the coefficient of discharge and Reynolds number. It then uses these values to calculate mass flow rate and standard volumetric flow rate. The algorithm accounts for factors like pipe diameter, upstream and downstream tap positions, beta ratio and density calculations.

Uploaded by

yan2hua
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
472 views

AGA3 1990 Algorithm

The document describes the AGA3 1990 algorithm for calculating gas flow measurements. The algorithm takes input parameters like pressure, temperature, compressibility and uses an iterative process to calculate the coefficient of discharge and Reynolds number. It then uses these values to calculate mass flow rate and standard volumetric flow rate. The algorithm accounts for factors like pipe diameter, upstream and downstream tap positions, beta ratio and density calculations.

Uploaded by

yan2hua
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

AGA3 1990 Algorithm http://www.squinch.

org/
AGA 3 takes meter settings, compressibilities, a differential pressure, static pressure and temperature, and calculates base volume, base volume flow rate or volume correction factor. It requires flowing and base pressure, temperature and compressibility.

AGA3: Enter a flowing temperature, pressure and compressibility, a base temperature, pressure and compressibility, a flowing volume and a meter factor, then press Calculate.
Value Units ? Diff Press = Flowing Pressure = Flowing Temp = Downstream Pressure Tap? Orifice diameter = Pipe diameter = Flowing Compressibility = Base Compressibility = Ideal specific gravity = Base Pressure = Base Temp = Orifice diameter temp = Orifice therm exp. coeff. = Pipe diameter temp = Pipe therm exp. coeff. = Input

SI
10. 0 4101. 325 10. 0

US

SI units SI kPa kPaA Deg C

US units US in WC @ 60F PSIA Deg F

50. 8 102. 26 0. 904351

0. 607527 101. 325 15

1. 665e-5 20 1. 116e-5

mm in mm in Deg C Deg F kPaA PSIA Deg C Deg F Deg C Deg F mm/(mm Deg C) in/(in Deg F) Deg C Deg F mm/(mm Deg C) in/(in Deg F)

Results Table

AGA 3 1990 Algorithm


The algorithm for the calculation is as follows. There is one iterative loop to solve for Reynolds number and coefficient of discharge. The standard defines many constants. Constants of the form A and S are simply fixed numbers and do not change based on the system of units used. Constants of the form Nx are unit conversion constants and are determined based on the system of units in use for the calculation. For further details on the calculation, refer to part 4 of the specification AGA3 1990 / GPA 8185-92.

Set unit conversion constants for the unit system chosen Calculate flowing density: Dflow = Pf * Mrair * Gi / (Zf * R * (Tf + N5)) Calculate base density: Dbase = Pb * Mrair * Gi / (Zb * R * (Tb + N5)) Calculate size of orifice at flowing conditions: d' = d * [1 + alpha1 * (Tf - Tdm)] Calculate size of meter run at flowing conditions: D' = D * [1 + alpha2 * (Tf TDm)] Calculate beta = d' / D' Calculate velocity of approach factor: Ev = 1 / sqrt( 1 - beta 4) Calculate factors required for coefficient of discharge / Reynolds number iteration loop. o Upstream tap position L1 = N4/D o Downstream tap position L2 = N4/D ( -8.5 L ) (-6.0 L ) o Upstream tap correction factor Tu = [ S2 + S3 e 1 + S4 e 1 ] * beta
1.1

o o o o o o o o o o o o o

Dimensionless downstream dam height M2 = (2 L2 ) / (1 - beta) Downstream tap correction factor Td = S6 [ M2 + S7 M2 1.3 ] beta 1.1 Small pipe correction factor: if D <= (A4 N4) then Ts = A3 (1 - beta) (A4 D/N4) else Ts = 0 Cd0 = A0 + A1 beta 2 + A2 B 8 + Tu + Td + Ts Cd1 = A5 * beta 0.7 (250) 0.7 Cd2 = A6 * beta 4 (250) 0.35 Cd3 = S1 * beta 4 * beta 0.8 (4.75) 0.8 (250) 0.35 Cd4 = (S5Tu + S8Td ) beta 0.8 (4.75) 0.8 Orifice differential pressure to flowing pressure ratio x = dP / (N3 * Pf) Yp = (0.41 + 0.35 beta 4) / k Expansion factor Y = 1 - Yp x Calculate Ftmp = Ev Y d 2 Calculate FIc = 4000 NIc D * mu / Ftmp

Calculate FIp = sqrt ( 2 * Dflow * dP) Calculate FI = FIc / FIp Limit FI to 1000 maximum. Set up coefficient of discharge loop by setting Cd(FT) to Cd0 Perform loop: o X = Fl / Cd(FT) o If X < Xc then 0.35 Fc = Cd0 + ( Cd1 X + Cd2 + Cd3 X 0.8 ) X 0.35 + Cd4 X 0.8 0.35 Dc = ( 0.7 Cd1 X + 0.35 Cd2 + 1.15 Cd3 X 0.8 ) X 0.35 + 0.8 Cd4 X
0.8

o o o

else

Fc = Cd0 + Cd1 X 0.7 + ( Cd2 + Cd3 X 0.8 ) ( A - B / X ) + Cd4 X 0.8 Dc = 0.7 Cd1 X 0.7 + ( Cd2 + Cd3 X 0.8 ) * B / X + 0.8 Cd3 ( A - B / X) X 0.8 + 0.8 Cd4 X 0.8 o Calculate the amount to vary Cd(FT) by: dCd = [ Cd (FT) - Fc] / [ 1 + Dc / Cd(FT) ] o Change Cd(FT) : Cd(FT) = Cd(FT) - dCd Until the absolute value of dCd is less than 0.000005. Reynolds number is Re = 4000 / X Calculate mass flow factor: F mass = ( pi / 4) * Nc Ev d2 Calculate mass flow rate: qm = F mass Cd(FT) Y * sqrt (2 Dflow * dP ) Calculate standard flow rate: qv = qm / D base

You might also like