Digital Storage Oscilloscope

TBS2000B Series Datasheet

Key features
9-inch WVGA color display with 15 horizontal grids shows 50% more
signal
TekVPI probe interface supports active, differential, and current probes
with automatic scaling and units
New front-end design enables more accurate measurements
32 automated measurements, and FFT function for quick waveform
analysis
Search and Mark features for easy identification of events that occur in
the acquired waveform
HelpEverywhere provides helpful on-screen tips for new users
Built-in Scope Intro handbook provides operating instructions and
oscilloscope fundamentals
The instrument user interface and the front panel overlay is translated
into 10 languages

Connectivity
USB 2.0 host port on the front panel for quick and easy data storage
USB 2.0 device port on rear panel for easy connection to a PC
10/100BASE-T Ethernet port for remote control over LAN
Wi-Fi interface provides wireless communications capability support 1

Education
The TBS2000B Series of Oscilloscopes with a 9-inch WVGA display, Courseware function presents lab exercise guidance on the display
5 million point record length and 2 GS/s sample rate, capture and display Fully compatible with TekSmartLab lab management software for
significantly more signal to help you debug and validate the designs faster. education
Easily and confidently analyze your signals with new on-waveform cursor
readouts and 32 automated measurements, each with informative tips. The Autoset, Cursors and Automated measurements can be disabled to
TekVPI® probe interface supports traditional passive BNC probes, but also help educators to teach basic concepts to students
enables wide application coverage with the latest active voltage probes and
current probes.

Key performance specifications

2 and 4 analog channel models
200 MHz, 100 MHz, and 70 MHz bandwidth models up to 2 GS/s
sampling rate
5 M record length on all channels
5 year warranty

1 A Wi-Fi adapter is available in some countries from Tektronix distributors as an accessory, model TEK-USB-WIFI. See Ordering Information for details.

www.tektronix.com 1
 Digital Storage Oscilloscope

Specifications
All specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise.

Model overview
Models TBS2072B TBS2074B TBS2102B TBS2104B TBS2202B TBS2204B
Analog Channels 2 4 2 4 2 4
Bandwidth 70 MHz 70 MHz 100 MHz 100 MHz 200 MHz 200 MHz
Sample rate 2 GS/s 2 GS/s 2 GS/s 2 GS/s 2 GS/s 2 GS/s
Record length 5 M points 5 M points 5 M points 5 M points 5 M points 5 M points

Vertical system analog channels

Hardware bandwidth limits 20 MHz

Input coupling DC, AC, or GND

Input impedance 1 MΩ ± 1 %, 13 pF ± 1.5 pF

Input sensitivity range 2mV/div 10 V/div

Vertical resolution 8 bits

Maximum input voltage, 1 MΩ 300 V RMS with peaks ≤ ±450 V

Acquisition modes
Sample Acquire sampled values.
Peak Detect Captures glitches as narrow as 3.5 ns at all sweep speeds.
Average From 2 to 512 waveforms included in average.
Hi-Res Averages multiple sample of one acquisition interval into one waveform point.
Roll Scrolls waveforms right to left across the screen at sweep speeds slower than or equal to 40 ms/div (400 ms/div at 20M record
length).

Waveform math
Arithmetic: Add
Subtract
Multiply
FFT

DC balance ± (1 mV +0.1 div)

DC gain accuracy ± 2% 10 V/div through 5 mV/div±

3% typical 2 mV/div

www.tektronix.com 9
Datasheet

Vertical system analog channels

DC voltage measurement accuracy
average mode
Average of 16 waveforms ±((DC Gain Accuracy) X |reading - (offset - position)| + Offset Accuracy + 0.11 div + 1 mV)
Delta Volts between any two ±(DC Gain Accuracy X |reading| + 0.08 div + 1.4 mV)
averages of ≥16 waveforms
acquired with the same
oscilloscope setup and
ambient conditions

Vertical position range ± 5 divisions

Vertical offset ranges Volts/Div setting Offset range, 1 MΩ

2 mV/Div to 63 mV/Div ±1V
64 mV/div to 999 mV/div ± 10 V
1 V/div to 10 V/div ± 100 V

Analog bandwidth, DC coupled

200 MHz models: DC to >200 MHz
100 MHz models: DC to ≥100 MHz
70 MHz models: DC to ≥70 MHz

Common mode rejection ratio 100:1 at 60 Hz, reducing to 10:1 with 50 MHz sine wave with equal Volts/div and coupling settings on each channel.
(CMRR), typical

Channel-to-channel isolation TBS2072B, TBS2074B TBS2102B, TBS2104B TBS2202B, TBS2204B

≥100:1 at ≤70 MHz ≥100:1 at ≤100 MHz ≥100:1 at ≤200 MHz

Horizontal system analog channels

Maximum duration of time 5 ms
captured at highest sample rate
(all channels)

Time base range TBS220x: 1 ns/div to 100 sec/div

TBS207x, TBS210x: 2 ns/div to 100 sec/div

Time-base delay time range -15 divisions to 5000 s

Deskew range ±100 ns

Time base accuracy ±25 ppm over any ≥1 ms interval

10 www.tektronix.com
SPECIFICATIONS
RF GENERATOR
Waveforms Sine, Square, Ramp, Pulse, Noise, ARB
Amplitude (into 50Ω) 1mVpp to 2 Vpp (MFG-2XXXMF); 1mVpp to 1 Vpp (MFG-2XXXMR)
Offset ±1 Vpk AC + DC (into 50Ω); ±2Vpk AC + DC (Open circuit)
Frequency 1uHz ~ 160MHz (MFG-2XXXMF); 1uHz ~ 320MHz (MFG-2XXXMR)
MODULATI0N/ Modulation Type AM, FM, PM, FSK, PWM (The detail same as CH1 modulation specification)
SWEEP Sweep Type Frequency
Source INT/EXT(INT only for AM, FM, PM, PWM)
PSK Carrier Waveforms Sine, Square, Triangle, Ramp, Pulse
Modulating Waveforms 50% duty cycle square
Internal Frequency 2 mHz to 1 MHz
Phase Range 0˚~ 360.0˚
Source Internal/External
ASK Carrier Waveforms Sine, Square, Triangle, Ramp, Pulse
Modulating Waveforms 50% duty cycle square
Internal Frequency 2 mHz to 1 MHz
Amplitude Range 0% ~ 100.0%
Source Internal/Externa
ARB function Sample Rate 200 MSa/s
Waveform Length 16k points
Amplitude Resolution 14 bits
User-defined output section From point 2 ~ 16384 (optional)
Jitter 20ppm +5ns

POWER AMPLIFIER
POWER AMPLIFIER Input Impedance 10KΩ
Input Voltage 1.25Vpmax
Working Mode Constant Voltage
Gain 20dB
Output Power (RL=8Ω) 20W (Square)
Output Voltage 12.5Vpmax
Output Current 1.6Amax
Rise/Fall Time <2.5uS
Full Power Bandwidth DC-100KHz
Overshoot 5%
Total Harmonic Ddistortion < 0.1% (Ampl >1Vpp); 20Hz ~ 20 kHz
Ground Isolation 42Vpk max
ADVANCED FUNCTIONS
AM MODULATION Carrier Waveforms Sine, Square, Triangle, Ramp, Pulse, Arb
Modulating Waveforms Sine, Square, Triangle, Upramp, Dnramp
Modulating Frequency 2mHz ~ 20kHz (Int) DC ~ 20kHz (Ext)
Depth 0% ~ 120.0%
Source Internal / External
FM MODULATION Carrier Waveforms Sine, Square, Triangle, Ramp
Modulating Waveforms Sine, Square, Triangle, Upramp, Dnramp
Modulating Frequency 2mHz ~ 20kHz (Int) DC ~ 20kHz (Ext)
Peak Deviation DC to max frequency
Source Internal / External
PM Carrier Waveforms Sine, Square, Triangle, Ramp
Modulating Waveforms Sine, Square, Triangle, Upramp, Dnramp
Modulation Frequency 2mHz ~ 20kHz (Int) DC ~ 20kHz (Ext)
Phase Deviation 0˚ ~ 360.0˚
Source Internal / External
SUM Carrier Waveforms Sine, Square, Triangle, Ramp
Modulating Waveforms Sine, Square, Triangle, Upramp, Dnramp
Modulation Frequency 2mHz ~ 20kHz (Int) DC ~ 20kHz (Ext)
SUM Depth 0% ~ 100.0%
Source Internal / External
PWM Carrier Waveforms Sine, Square, Triangle, Ramp
Modulating Waveforms Sine, Square, Triangle,Upramp, Dnramp
Modulation Frequency 2mHz ~ 20kHz (Int) DC ~ 20kHz (Ext)
Phase Deviation 0% ~ 100.0% pulse width
Source Internal / External
FSK Carrier Waveforms Sine, Square, Triangle, Ramp, Pulse
Modulating Waveforms 50% duty cycle square
Internal Frequency 2 mHz to 1 MHz
Frequency Range 1μHz to max frequency
Source Internal / External
SWEEP Waveforms Sine, Square, Triangle, Ramp
Type Linear or Logarithmic
Sweep Direction Sweep up or sweep down
Start/Stop Freq 1uHz to max frquency
Sweep Time 1ms to 500s
Source Internal / External
Trigger Single, External, Internal
Marker Marker signal on falling edge (programmable)
Source Internal / External
BURST Waveforms Sine, Square, Triangle, Ramp
Frequency 1uHz ~ Max Frequency
Pulse Count 1~1000000 Cycles or intfinite
Start/Stop Phase -360.0˚~ +360.0˚
Internal Frequency 1 us ~ 500 s
Gate Source External Trigger
Trigger Source Single, External, Internal
 SPECIFICATIONS
TRIGGER DELAY NCycle, Infinite 0s ~ 100 s
EXTERNAL Type For FSK, Burst, Sweep
TRIGGER INPUT Input Level TTL Compatibility
Slope Rising or Falling(Selectable)
Pulse Width >100ns
Input Impedance 10kΩ，DC coupled
EXTERNAL Type For AM, FM, PM, SUM, PWM
MODULATION Voltage Range ±5V full scale
INPUT Input Impedance 10kΩ
Frequency DC to 20kHz
Ground Isolation 42Vpk max
TRIGGER OUTPUT Type For FSK, Burst, Sweep
Level TTL Compatible into 50Ω
Pulse Width >450ns
Maximum Rate 1MHz
Fan-out ≥4 TTL Load
Impedance 50Ω Typical
FREQUENCY Range 5Hz ~ 150MHz
COUNTER Accuracy Time Base accuracy±1count
Time Base ±20ppm (23˚C ±5˚C)
Resolution The maximum resolution is : 100nHz for 1Hz, 0.1Hz for 100MHz
Input Impedance 1kΩ/1pf
Sensitivity 35mVrms ~ 30Vms (5Hz ~ 150MHz)
Ground Isolation 42Vpk max
Dual Channel Phase -180
~180
Synchronize phase
Function Track CH2=CH1
(CH1/CH2) Coupling Frequency (Ratio or Difference)
Dsolink Amplitude & DC Offset
√
OTHER Store/Recall 10 Groups of Setting Memories
Interface LAN, USB
Display 4.3 inch TFT LCD, 480 × 3 (RGB) × 272
GENERAL Power Source AC 100 ~ 240V, 50 ~ 60Hz or AC 100 ~ 120V, AC 220 ~ 240V, 50 ~ 60Hz
SPECIFICATIONS Power Consumption 30W or 80W(With power amplifier)
Operating Environment Temperature to satisfy the specification : 18 ~ 28˚C ; Operating temperature : 0 ~ 40˚C ; Relative Humidity:
≤ 80%, 0 ~ 40˚C, ≤ 70%, 35 ~ 40˚C ; Installation category : CAT II
Operating Altitude 2000 Meters
Pollution Degree IEC 61010 degree 2, Indoor use
Storage Temperature -10 ~ 70˚C, Humidity : ≤70%
Dimensions & Weight 266(W) x 107(H) x 293(D) mm ; Approx. 2.5kg

The specifications apply when the function generator is powered on for at least 30 minutes under +20°C~+30°C Specifications subject to change without notice. MFG-2000GD1BH
Note : (1). A total of ten waveforms can be stored. (Every waveform can be composed of a maximum of 16k points)
(2). Add 1/10th of output amplitude and offset specification per ºC for operation outside of 0ºC to 28ºC range (1-year specification)
(3). DC offset set to zero
(4). Jitter specification for RF Generator: 20ppm +5ns
(5). Only Pluse channel support

ORDERING INFORMATION ACCESSORIES

MFG-2110 10MHz Single Channel Arbitrary Function Generator with Pulse Generator Quick Start Guide x 1, CD-ROM with MFG Software and
MFG-2120 20MHz Single Channel Arbitrary Function Generator with Pulse Generator User Manual x 1
MFG-2120MA 20MHz Single Channel Arbitrary Function Generator with Pulse Generator, Modulation, GTL-110 BNC Cable x 1 (MFG-2110/2120/2120MA/2130M/
Power Amplifier 2160MF/2160MR)
MFG-2130M 30MHz Single Channel Arbitrary Function Generator with Pulse Generator, Modulation
GTL-110 BNC Cable x 2 (MFG-2230M/2260M/2260MFA/
MFG-2160MF 60MHz Single Channel Arbitrary Function Generator with Pulse Generator, Modulation, 2260MRA)
160MHz RF Aignal Generator
MFG-2160MR 60MHz Single Channel Arbitrary Function Generator with Pulse Generator, Modulation,
320MHz RF Signal Generator OPTIONAL ASSESSORIES
MFG-2230M 30MHz Dual Channel Arbitrary Function Generator with Pulse Generator, Modulation GTL-246 USB Type A to Type B cable
MFG-2260M 60MHz Dual Channel Arbitrary Function Generator with Pulse Generator, Modulation FREE DOWNLOAD
MFG-2260MFA 60MHz Dual Channel Arbitrary Function Generator with Pulse Generator, Modulation, Arbitrary Waveform Editing Software
160MHz RF Signal Generator, Power Amplifier
MFG-2260MRA 60MHz Dual Channel Arbitrary Function Generator with Pulse Generator, Modulation,
320MHz RF Signal Generator, Power Amplifier

Global Headquarters U.S.A. Subsidiary

GOOD WILL INSTRUMENT CO., LTD. INSTEK AMERICA CORP.
No.7-1, Jhongsing Road, Tucheng Dist., New Taipei City 236, Taiwan 5198 Brooks Street Montclair, CA 91763, U.S.A.
T +886-2-2268-0389 F +886-2-2268-0639 T +1-909-399-3535 F +1-909-399-0819
E-mail: [email protected] E-mail: [email protected]
China Subsidiary
Japan Subsidiary
GOOD WILL INSTRUMENT (SUZHOU) CO., LTD.
No. 521, Zhujiang Road, Snd, Suzhou Jiangsu 215011 China TEXIO TECHNOLOGY CORPORATION.
T +86-512-6661-7177 F +86-512-6661-7277 7F Towa Fudosan Shin Yokohama Bldg., 2-18-13 Shin
E-mail: [email protected] Yokohama, Kohoku-ku, Yokohama, Kanagawa,
222-0033 Japan Simply Reliable
Malaysia Subsidiary T +81-45-620-2305 F +81-45-534-7181
GOOD WILL INSTRUMENT (M) SDN. BHD. E-mail: [email protected]
No. 1-3-18, Elit Avenue, Jalan Mayang Pasir 3,
11950 Bayan Baru, Penang, Malaysia Korea Subsidiary
T +604-6111122 F +604-6115225
E-mail: [email protected] GOOD WILL INSTRUMENT KOREA CO., LTD.
Room No.503, Gyeonginro 775 (Mullae-Dong 3Ga,
Europe Subsidiary Ace Hightech-City B/D 1Dong), Yeongduengpo-Gu,
GOOD WILL INSTRUMENT EURO B.V. Seoul 150093, Korea.
De Run 5427A, 5504DG Veldhoven, THE NETHERLANDS T +82-2-3439-2205 F +82-2-3439-2207 www.gwinstek.com www.facebook.com/GWInstek
T +31(0)40-2557790 F +31(0)40-2541194 E-mail : [email protected]
 LB1005 High-Speed Servo Controller
FLEXIBLE, EASY-TO-USE, P-I CONTROLLER

The LB1005 High-Speed Servo Controller makes stabilizing the frequency or amplitude of lasers
easy and intuitive. And, unlike competitive products currently available, the LB1005 Servo
Controller is a one-box solution - no expensive external chassis required. This high-speed
proportional integral (P-I) controller has an intuitive front panel for the independant control of the
P-I corner frequency, overall servo gain, and low-frequency gain limit. This flexibility allows the
user to cascade a pair of LB1005 units to, for instance, provide a very tight lock on a diode laser.
One controller can be tuned to eliminate high frequency noise via the current modualtion input.
A second controller can respond to the low frequency components of the same error signal to
eliminate drift and acoustic perturbations. The LB1005 is ideal for demanding applications
including atom, ion, or molecule trapping, Bose-Einstein condensation, frequency metrology,
quantum optics, and the high-speed stabilization, synchronization, and control of lasers.

WAVELENGTH LOCKING WITH THE LB1005

SERVO CONTROLLER
While narrow-linewidth lasers are used throughout atomic, molecular, and optical physics,
Applications their short-term wavelength stability is often not adequate for many applications without
• Frequency and amplitude stabilization of lasers active stabilization. Feedback (or servo) control forces a system, such as a laser, to stay
actively "locked" to a desired value, e.g., a specific wavelength - automatically correcting for
• Atom/ion trapping, including BEC external disturbances that might cause the system to deviate from the desired value.
• Frequency metrology
The New Focus LB1005 High-Speed Servo Controller provides critical signal-processing
• Quantum optics electronics for performing the feedback control. In the case of wavelength locking, an error
• Laser synchronization signal is generated by transmitting a portion of the laser output through a wavelength
reference such as a gas cell or etalon. Any wavelength instability is converted to an amplitude
charge that can be detected by a photodetector. The resulting error signal is filtered by the
LB1005 Servo Controller to form a control signal that is sent back to the laser. (Figure 1)

The LB1005 Servo Controller consists of three stages of analog electronics processing: Input
Stage, Filter Stage, and Output Stage. (Figure 2) The Filter Stage is the most important
because it sets the behavior of the system. The user controls three important filter parameters
that impact the stability of the system, and how well the actual output matches the desired
value (P-I corner, Proportional Gain, and Low Frequency Gain Limit).

Differential inputs that are auto-terminated if not used, a sensitive, low-noise offset for lock
point selection, and an error monitor output make the Input Stage flexible. The Output Stage
not only provides the correction signal, but also control over the amplitude of the correction
signal to match the input to the laser being locked. Sweep input, span, and center
adjustments make it easy to find the desired lock point and a TTL "Integrator Hold" and
modulation inputs allow for more advanced locking techniques not available in competitors'
models. Simply BetterTM.
 LB1005 High-Speed Servo Controller
Wavelength Locking with the LB1005
The wavelength of narrow-linewidth tunable lasers drifts due to floor vibrations, small temperature drifts, and even acoustic noise from people talking in
the vicinity of the laser. By using the piezoelectric transducer input to the laser controller, you can shift the laser wavelength so that it always stays fixed
on the stable resonance line shape of the sample gas, regardless of possible external disturbances.

To acquire lock, find the locking point by adjusting Sweep Center and Sweep Span (and sometimes Offset Adjust). Upon locating the locking point, the
Acquire switch is used to turn on the fedback control. The Sweep Span is then turned OFF, and the Gain can be adjusted to optimize servo control.

LB1005 Specifications
Specifications Value
Input Voltage Noise <10 nV/√ Hz
Input Impedance 1 MW
Input/Output Voltage ±10 V
Bandwidth >10 MHz
Adjustable Gain -40 to +40 dB
Adjustable P-I Corner 10 Hz to 1 MHz
Frequency Range
Integrator Hold TTL Triggered

Gain and P-I corner are independently adjustable.

Figure 1. Schematic of a general feedback control loop.

Figure 2. LB1005 High-Speed Servo Controller architecture. Proportional-Integral Filter Gain profile with Low-Frequency Gain Limit. Independently adjustable
gain and P-I corner frequency provide a high degree of flexibility.

www.newport.com/newfocus
3635 Peterson Way, Santa Clara, CA 95054, USA
PHONE: 1-800-222-6440 1-408-980-4300 FAX: 1-408-919-6083 EMAIL: [email protected]

PHONE EMAIL PHONE EMAIL

Belgium +32-(0)0800-11 257 [email protected] Irvine, CA, USA +1-800-222-6440 [email protected]
China +86-10-6267-0065 [email protected] Netherlands +31-(0)30 6592111 [email protected]
France +33-(0)1-60-91-68-68 [email protected] United Kingdom +44-1235-432-710 [email protected]
Japan +81-3-3794-5511 [email protected] Germany / Austria / Switzerland
Taiwan +886 -(0)2-2508-4977 [email protected] +49-(0)6151-708-0 [email protected]

Newport Corporation, Irvine, California and Franklin, Massachusetts; Evry and Newport Corporation, Global Headquarters PHONE: 1-800-222-6440 1-949-863-3144
Beaune-La-Rolande, France and Wuxi, China have all been certified compliant with 1791 Deere Avenue, Irvine, CA 92606, USA EMAIL: [email protected]
ISO 9001 by the British Standards Institution. Santa Clara, California is DNV certified. Complete listings for all global office locations are available online at www.newport.com/contact
DS-031301 (9/14)
S3532 Series Spectrum Analyzer
Datasheet

Saluki Technology Inc.

 Tel: 886.909 602 109 Email: [email protected]
www.salukitec.com

The document applies to the instruments of the following models:

 S3532A spectrum analyzer (9kHz-3.6GHz).

 S3532B spectrum analyzer (9kHz-7.5GHz).

Standard Accessories of S3532 spectrum analyzer

Item Name Qty

1 Main Machine 1 Set

2 Power Cord 1 pcs

3 CD 1 pcs

Options of the S3532 spectrum analyzer:

Option No. Item Description

S3532-01 Field Strength Measurement /

S3532-02 Near Field Probe Kit /

S3532-03 Frequency Identity Module /

S3532-04 Directional Antenna Frequency range: 600MHz - 8GHz

S3532-05 Omnidirectional Antenna Frequency range: 300MHz - 7.5GHz

S3532-06 SWR Bridge Frequency range: 10MHz - 3.6GHz

S3532-07 USB Power Sensor Frequency range: 10MHz - 6GHz

S3532-08 RF Demonstration Kit /

2
 Tel: 886.909 602 109 Email: [email protected]
www.salukitec.com

2.8.Spurious Response
S3532A S3532B

TOI (>30MHz) +10dBm +13dBm

SHI (>10MHz) +30dBm +40dBm

Input related spurious (>10MHz) <-60dBc

Inherent residual response (>10MHz) <-85dBm

2.9.Tracking Generator
S3532A S3532B

Frequency range 100kHz - 3.6GHz 100kHz - 3.2GHz

Output level -30dBm To 0dBm Stepped by 1 dB

Output flatness ±3dB

2.10. General

S3532A S3532B

Display 8.4 inch TFT LCD 8.4 inch TFT LCD

Detector Sample, Peak, Negative peak, Normal

Marker Counter Resolution 1Hz, 10Hz, 100Hz, 1kHz

Limit Line Available

Dimensions 390(H)×182(W)×230(D)mm 390(H)×182(W)×230(D)mm

Weight 6.5Kg 6.5Kg

Operating Temperature range 0℃ to 40℃ 0℃ to 40℃

Storage Temperature range -20℃ to +70℃ -20℃ to +70℃

Input Voltage 100V-240V AC 100V-240V AC

Power Input Frequency 40Hz - 60Hz 40Hz - 60Hz

Consumption Max.30W Max.30W

- End of Document -

8
High Frequency Lock-In Amplifier
SR844 — 200 MHz dual phase lock-in amplifier

SR844 200 MHz Lock-In Amplifier

The SR844 is the widest bandwidth lock-in amplifier
· 25 kHz to 200 MHz frequency range available. It provides uncompromised performance with a
frequency range of 25 kHz to 200 MHz and up to 80 dB of
· 80 dB dynamic reserve drift-free dynamic reserve. It includes the many features, ease
of operation, and programmability that you’ve come to expect
· Time constants from 100 µs to 30 ks from SRS DSP ­lock-in amplifiers.
(6, 12, 18 or 24 dB/oct rolloff) Digital Technology
· “No Time Constant” mode The SR844 uses the same advanced DSP technology found
(10 µs to 20 µs update rate) in the SR850, SR830 and SR810 lock-in ­amplifiers. DSP
offers many advantages over analog instruments — high
· Auto-gain, -phase, -reserve and -offset dynamic reserve, low zero-drift, accurate RF phase shifts and
orthogonality, and digital output filtering.
· Two 16-bit DACs and ADCs Signal Input
· Internal or external reference The SR844 has both 50 Ω and 1 MΩ inputs. The 1 MΩ input
is used with high source impedances at low f­requencies, or
· GPIB and RS-232 interfaces with a standard 10× scope probe. The 50 Ω input ­provides the
best RF signal ­matching. Up to 60 dB of RF attenuation
or 20 dB of RF gain can be selected in 20 dB increments.
Full-scale sensitivities range from 1 Vrms (+13 dBm) to
100 nVrms (–127 dBm). Gain allocation can be optimized to
provide up to 80 dB of dynamic reserve.

Reference
· SR844 ... $8450 (U.S. list) The SR844 offers both external and internal reference
operation. In both cases, the entire 25 kHz to 200 MHz

Stanford Research Systems phone: (408)744-9040

www.thinkSRS.com
 SR844 Specifications

Signal Channel Harmonic rejection

Odd harmonics –9.5 dBc @ 3 × ref, –14 dBc @ 5 ×
Voltage input Single-ended BNC ref, etc. (20 log 1­/n, n = 3, 5, 7...)
Input impedance 50 Ω or 1 MΩ + 30 pF Even harmonics <–40 dBc
Damage threshold ±5 V (DC + AC) Sub-harmonics <–40 dBc
Bandwidth 25 kHz to 200 MHz Spurious responses –10 dBc @ ref ± 2 × IF
Sensitivity –23 dBc @ ref ± 4 × IF
<1 MHz 100 nVrms to 1 Vrms full scale <–30 dBc otherwise
<50 MHz 1 µVrms to 1 Vrms full scale
<200 MHz 10 µVrms to 1 Vrms full scale Displays
Gain accuracy
<50 MHz ±0.25 dB Channel 1
<200 MHz ±0.50 dB Type 4½-digit LED and 40-seg. bar graph
Gain stability 0.2 %/ºC Quantities X, R (V or dBm), X-noise, Aux In 1
Coherent pickup Low-noise reserve, sens. <30 mV Channel 2
f < 10 MHz <100 nV (typ.) Type 4½-digit LED and 40-seg. bar graph
f < 50 MHz <2.5 µV (typ.) Quantities Y, θ, Y-noise (V or dBm), Aux In 2
f < 200 MHz <25 µV (typ.) Expand ×10 or ×100 for Ch1 and Ch2
Input noise (50 Ω) 2 nV/√Hz (typ.), <8 nV/√Hz (max.) Ratio X and Y ratioed with respect to Aux
Input noise (1 MΩ) 5 nV/√Hz (typ.), <8 nV/√Hz (max.) In 1 or Aux In 2 before filtering and
Dynamic reserve up to 80 dB computation of R. The ratio input
is normalized to 1 V and has a
Reference Channel ­dynamic range greater than 100.
Reference
External reference 25 kHz to 200 MHz Type 4½-digit LED
Impedance 50 Ω or 10 kΩ + 40 pF Quantities Ref Freq, Phase, Offsets, Aux Out,
Level 0.7 Vpp pulse or 0 dBm sine IF Freq, Elapsed Time
Pulse width >2 ns at any frequency
Threshold setting Automatic, midpoint of waveform Channel 1 and Channel 2 Outputs
Acquisition time <10 s (auto-ranging, any frequency)
<1 s (within same octave) Voltage range ±10 V full scale proportional to X,
Internal reference 25 kHz to 200 MHz Y or CH1, CH2 displayed quantity
Freq. resolution 3 digits Update rate
Freq. accuracy ±0.1 in the 3rd digit X, Y 48 to 96 kHz
Harmonic detection 2F (50 kHz to 200 MHz) R, θ, Aux inputs 12 to 24 kHz
Reference outputs Phase locked to int./ext. reference X-noise, Y-noise 512 Hz
Front panel 25 kHz to 200 MHz square wave
1.0 Vpp nominal into 50 Ω Auxiliary Inputs and Outputs
Rear panel (TTL) 25 kHz to 1.5 MHz, 0 to +5 V
nominal, ≥3 V into 50 Ω Inputs 2
Phase resolution 0.02° Type Differential, 1 MΩ
Absolute phase error Range ±10 V
<50 MHz <2.5° Resolution 0.33 mV
<100 MHz <5.0° Bandwidth 3 kHz
<200 MHz <10.0° Outputs 2
Rel. phase error, orthog. <2.5° Range ±10 V
Phase noise (external) 0.005° rms at 100 MHz, Resolution 1 mV
100 ms time constant Data buffers Two 16,000 point buffers. Data is
Phase drift recorded at rates up to 512 Hz and
<10 MHz <0.1°/°C is read using computer interfaces.
<100 MHz <0.25°/°C
<200 MHz <0.5°/°C General

Demodulator Interfaces IEEE-488.2 and RS-232 interfaces

are­ standard.
Zero stability Digital displays have no zero-drift. Power 70 W, 100/120/220/240 VAC,
Analog outputs have <5 ppm/°C 50/60 Hz
drift for all dyn. reserve settings. Dimensions 17" × 5.25" × 19.5" (WHD)
Time constants 100 µs to 30 ks with 6, 12, 18 or Weight 23 lbs.
24 dB/octave rolloff Warranty One year parts and labor on defects
“No Filter” mode 10 to 20 µs update rate (X and Y) in materials and workmanship

Stanford Research Systems phone: (408)744-9040

www.thinkSRS.com
HF2LI Zurich
50 MHz Lock-in Amplifier Instruments
2 Input Channels, 2 Signal Outputs
High dynamic reserve, low noise

Product Leaflet
Release date: January 2019

Key Features
 DC – 50 MHz, 210 MSa/s, 14 bit
 5 nV/√Hz input noise, 120 dB dynamic reserve,
1 μs minimum time constant
 6 demodulators, up to 6 oscillators
 LabOne® Toolset: Scope, Parametric Sweeper,
Imaging Module, FFT Spectrum Analyzer
 APIs for LabVIEW® , .NET, MATLAB® , C and Python

Summary and the phase shift of each component can be controlled

with the HF2LI-MF Multi-frequency option installed.
The Zurich Instruments HF2LI is a high-frequency dual
channel lock-in amplifier that uses the latest hardware Demodulators and Filters
and software technologies to provide industry leading All filter properties of the 6 dual-phase demodulators can
specification and functionality. The dynamic reserve of be individually configured, including the time constants
120 dB sets the benchmark in the 50 MHz frequency (1 μs to 500 s) or bandwidths (80 μHz to 200 kHz) and filter
range. In many setups a single HF2LI replaces multiple orders (1st to 8th ). The digital filters offer a much higher
conventional instruments. dynamic reserve, zero drift, precise phase shifts, and per-
The basic instrument functionality can be extended with fect orthogonality in contrast to their analog counter-
the following upgrade options: parts.

 HF2LI-MF Multi-frequency LabOne is Instrument Control

 HF2LI-PID Quad PID Controller The HF2LI includes the LabOne control software. Thanks
 HF2LI-PLL Dual Phase-locked Loop to the latest web server technology, the user interface
 HF2LI-MOD AM/FM Modulation can be easily accessed from any browser. With LabOne
the computer is the cockpit for instrument control, data
These options are upgradable in the field. For current
capture, analysis and storage where every setting is no
measurements we offer the HF2TA Current Amplifier as
more than 2 clicks away. The functionality includes an
an active probe that can be placed close to the setup, e.g.
Oscilloscope, a Spectrum Analyzer, an Imaging Module,
for 4-probe measurements.
a Plotter and a Parametric Sweeper for quick and easy
measurement automation and much more.
Description Choice of APIs
Signal Inputs and Outputs For convenient integration into existing control environ-
ments, programming interfaces for LabVIEW, .NET, MAT-
The two 14 bit signal inputs exhibit a minimum noise of 5
LAB, C and Python are provided.
nV/√Hz. The 210 MSa/s sampling rate ensures sufficient
aliasing suppression and high SNR. Linear combinations
of up to 6 sinusoids can be output at a resolution of 16 bit
in multiple ranges up to ±10 V. The amplitude, frequency,
Specification
General Demodulators & Reference
Dimensions 45 × 35 × 10 cm (19” rack) Number of 6 dual-phase
11.1 × 9.2 × 4 inch demodulators
Weight 6.2 kg; 8.4 lbs Number of oscillators 2 (6 with HF2LI-MF)
Power supply AC: 100 – 120 V; 220 – 240 V Output sample rate USB: up to 460 kSa/s
50/60 Hz Auxiliary outputs: 1 MSa/s
Time constant, 1 μs to 500 s,
Signal Inputs Meas. bandwidth 80 μHz to 200 kHz
Frequency range DC to 50 MHz Filter slope (dB/Oct) 6, 12, 18, 24, 30, 36, 42, 48
Input impedance 50 Ω or 1 MΩ || 20 pF X, Y, R, ϴ 64 bit full range
Input voltage noise 5 nV/√Hz (> 10 kHz) Phase resolution 1 μdeg
Dynamic reserve 120 dB Frequency resolution 0.7 μHz
Input range ±3.3 V
Input AC range ±1.5 V (DC coupling) Auxiliary & Others
A/D conversion 14 bit, 210 MSa/s Auxiliary Outputs 4 BNC, ±10 V, 16 bit,
1 MSa/s, offset, scaling
Signal Outputs Auxiliary Inputs 2 BNC, ±10 V, 16 bit,
400 kSa/s; 100 kHz bw
Frequency range DC to 50 MHz
Digital I/O 16 bit input, 16 bit
Output ranges ±10 mV, 100 mV, 1 V, 10 V
bidirectional, 50 MHz
Signal adder ±10 V, DC to 50 MHz
Other interfaces clock input, USB 2.0, 2×
D/A conversion 16 bit, 210 MSa/s ZCtrl, 2× ZSync

Front Back
Panel Signal Input 1 Digital Signal Processor Panel
Clock In 10 MHz
Input ADC Input
Range 210 MSa/s Matrix
Amplifier 14 bit HF2LI-MF
LPF 50 MHz LPF
×3

Signal Input 2
Input ADC Oscillator
Range 210 MSa/s Matrix
Amplifier 14 bit HF2LI-MF
LPF 50 MHz LPF
×3

Signal Output 1
HF2LI-PPL HF2LI-MOD 2× ZSync Synchronisation Bus

Output DAC
Range 210 MSa/s
Amplifier 16 bit Scope
2× ZCtrl Pre-amplifier Bus

Parametric Sweeper
Signal Output 2

Data Acquisition & Imaging USB 2.0 High-speed

Output DAC
Range 210 MSa/s
Amplifier 16 bit
FFT Spectrum Analyzer
Digital I/O 32-bit
HF2LI-PID 4x PID Controller
Auxiliary Outputs 1–4
4× DAC
1 MSa/s Frequency Generator Auxiliary Inputs 1, 2
16 bit
LPF 200 kHz
Output Numerical 2× ADC
Adders Oscillators 400 kSa/a
16 bit
Options LPF 100 kHz

Zurich Technoparkstrasse 1
CH-8005 Zurich
www.zhinst.com
[email protected]
Disclaimer: The content of this document is provided by Zurich Instruments ‘as is’.
Zurich Instruments makes no warranties with respect to the accuracy or completeness of

Instruments Switzerland +41 44 515 04 10

the content of this document and reserves the right to make changes to the specification
at any time without notice. All trademarks are the property of their respective owners.
 BILL OF MATERIAL

Sl no Description Qty (Nos) Price Total Price

Newport make PID Controller Model LB1005-

1 1
S
Zurich Instruments make Phasemeter Model
2 1
No HF2LI-PLL
Tektronix TBS2202B Digital Storage
3 1
Oscilloscope, 2 ch, 200 MHz, 2GS/s

4 Saluki S3532 series Spectrum Analyser 1

GW-Instek make Waveform Generator

5 1
Model No MFG-2220HM
Stanford systems Make Lock-in Amplifier
6 1
Model No SR-844
Reputed make Digital & FIR Filter Model No
7 1
HWT-1019S
Panel for mounting all the instruments in
8 1
one housing with wireless display

9 Integration & Installation Lumsum