SERVICE SERVICE MANUAL

MANUAL
D150B
Crawler Dozer

D150B
Crawler Dozer

1/1
Part number 47998875 Part number 47998875B
3rd edition English
June 2018

© 2018 CNH Industrial Latin America LTDA. All Rights Reserved.

 SERVICE MANUAL

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil
[N9AC03000 - ]

47998875B 21/05/2018
EN

Find manuals at https://best-manuals.com

 Link Product / Engine

Product Market Product Engine

D150B XLT, com cabine, Tier 3, Latin America F4HE9684U*J101
lâmina Power Angle Tilt (PAT),
produzido no Brasil [N9AC03000
-]

47998875B 21/05/2018

Find manuals at https://best-manuals.com

 Contents

INTRODUCTION
Engine....................................................................................... 10
[10.001] Engine and crankcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1

[10.400] Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2

[10.310] Aftercooler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3

[10.304] Engine lubrication system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4

Rear axle system........................................................................ 27

[27.120] Planetary and final drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.1

[27.126] Spur gear and final drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.2

Hydrostatic drive......................................................................... 29
[29.100] Transmission and steering hydrostatic control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.1

[29.202] Hydrostatic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.2

Brakes and controls .................................................................... 33

[33.202] Hydraulic service brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.1

Hydraulic systems....................................................................... 35
[35.000] Hydraulic systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.1

[35.104] Fixed displacement pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.2

[35.310] Distributor and lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.3

[35.350] Safety and main relief valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.4

[35.741] Dozer blade cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.5

[35.742] Ripper hydraulic system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.6

Tracks and track suspension ........................................................ 48

[48.130] Track frame and driving wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48.1

[48.110] Front suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48.2

[48.100] Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48.3

[48.134] Track tension units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48.4

47998875B 21/05/2018

Find manuals at https://best-manuals.com

 [48.138] Track rollers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48.5

Cab climate control ..................................................................... 50

[50.100] Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.1

[50.200] Air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.2

Electrical systems ....................................................................... 55

[55.013] Engine oil system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.1

[55.000] Electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.2

[55.100] Harnesses and connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.3

[55.525] Cab engine controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.4

[55.015] Engine control system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.5

[55.201] Engine starting system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.6

[55.301] Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.7

[55.302] Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.8

[55.202] Cold start aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.9

[55.010] Fuel injection system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.10

[55.012] Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.11

[55.019] Hydrostatic drive control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.12

[55.050] Heating, Ventilation, and Air-Conditioning (HVAC) control system. . . . . . . . . . . . . . . 55.13

[55.408] Warning indicators, alarms, and instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.14

[55.101] Chassis harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.15

[55.014] Engine intake and exhaust system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.16

[55.DTC] FAULT CODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55.17

Dozer blade and arm................................................................... 86

[86.110] Dozer blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86.1

Tools ......................................................................................... 89
[89.128] Ripper assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89.1

Platform, cab, bodywork, and decals ............................................. 90

[90.150] Cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90.1

47998875B 21/05/2018

Find manuals at https://best-manuals.com

[90.114] Operator protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90.2

[90.124] Pneumatically-adjusted operator seat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90.3

47998875B 21/05/2018

Find manuals at https://best-manuals.com

 47998875B 21/05/2018

Find manuals at https://best-manuals.com

 INTRODUCTION

47998875B 21/05/2018
1
Find manuals at https://best-manuals.com
 Contents

INTRODUCTION

Foreword - Important notice regarding equipment servicing (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Foreword - How to use and navigate through this manual (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety rules (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety rules (Signal word definitions) (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Safety rules (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Safety rules (Weld works) (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Safety rules - (Machine service) (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Torque (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Torque - Standard torque data for hydraulics (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Basic instructions - Shop and assembly (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Basic instructions (Daily inspection) (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
General specification (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Tracks (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Overall dimensions (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Ripper (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Machine weights (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Consumables (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Product identification (Sides of the machine) (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Part identification - (Identification plates) (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Product overview - (Machine Components) (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

(*) See content for specific models

47998875B 21/05/2018
2
Find manuals at https://best-manuals.com
 INTRODUCTION

Foreword - Important notice regarding equipment servicing

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.

Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.

The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.

The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.

In case of questions, refer to your NEW HOLLAND CONSTRUCTION Sales and Service Networks.

47998875B 21/05/2018
3
Find manuals at https://best-manuals.com
 INTRODUCTION

Foreword - How to use and navigate through this manual

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through web delivery (eTIM), DVD, and paper manuals. A coding system called
SAP has been developed to link the technical information to other Product Support functions, e.g., Warranty.

Technical information is written to support the maintenance and service of the functions or systems on a customer's
machine. When a customer has a concern on their machine it is usually because a function or system on their ma-
chine is not working at all, is not working efficiently, or is not responding correctly to their commands. When you refer
to the technical information in this manual to resolve that customer's concern, you will find all the information classified
using the SAP coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system, you will then find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies, and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system: the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting), and the service data (remove, install adjust, etc.).

By integrating SAP coding into technical information, you will be able to search and retrieve just the right piece of
technical information you need to resolve that customer's concern on his machine. This is made possible by attaching
3 categories to each piece of technical information during the authoring process.

The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - the component or function on the machine, that the piece of technical information is going to describe
(e.g., Fuel tank).
• INFORMATION TYPE - the piece of technical information that has been written for a particular component or func-
tion on the machine (e.g., Capacity would be a type of Technical Data describing the amount of fuel held by the fuel
tank).
• PRODUCT - the model for which the piece of technical information is written.

Every piece of technical information will have those three categories attached to it. You will be able to use any combi-
nation of those categories to find the right piece of technical information you need to resolve that customer's concern
on their machine.

That information could be:

• the procedure for how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool

47998875B 21/05/2018
4
 INTRODUCTION

Manual content
This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at
the end of each Chapter. Page number references are included for every piece of technical information listed in the
Chapter Contents or Chapter Index.

Each Chapter is divided into four Information types:

• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components, assemblies or
sub-assemblies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components, assemblies or
sub-assemblies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hydraulic
devices, components, assemblies or sub-assemblies.
• Service Data (remove disassemble, assemble, install) for all the mechanical, electrical or hydraulic devices, com-
ponents, assemblies or sub-assemblies.

Sections
Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by a
number (00, 35, 55, etc.). The Sections included in the manual will depend on the type and function of the machine that
the manual is written for. Each Section has a Contents page listed in alphabetic/numeric order. This table illustrates
which Sections could be included in a manual for a particular product.

PRODUCT
Tractors
Vehicles with working arms: backhoes, excavators,
skid steers, ….
Combines, forage harvesters, balers, ….
Seeding, planting, floating, spraying
equipment, ….
SECTION Mounted equipment and tools, ….
00 - Maintenance X X X X X
05 - Machine completion and equipment X X X X X
10 - Engine X X X X
14 - Main gearbox and drive X X X X
18 - Clutch X X X
21 - Transmission X X X X
23 - Four wheel drive (4WD) system X X X X
25 - Front axle system X X X X
27 - Rear axle system X X X X
29 - Hydrostatic drive X X X X
31 - Power Take-Off (PTO) X X
33 - Brakes and controls X X X X
35 - Hydraulic systems X X X X
36 - Pneumatic system X X X X
37 - Hitches, drawbars and implement couplings X X X
39 - Frames and ballasting X X X X X
41 - Steering X X X X
44 - Wheels X X X X
46 - Steering clutches
48 - Tracks and track suspension X X X
50 - Cab climate control X X X X
55 - Electrical systems X X X X X
56 - Grape harvester shaking
58 - Attachments/headers X
60 - Product feeding X

47998875B 21/05/2018
5
 INTRODUCTION

61 - Metering system X
62 - Pressing - Bale formation X
63 - Chemical applicators X
64 - Chopping X
66 - Threshing X
68 - Tying/Wrapping/Twisting X
69 - Bale wagons
70 - Ejection X
71 - Lubrication system X X X X X
72 - Separation X
73 - Residue handling X
74 - Cleaning X
75 - Soil preparation/Finishing
76 - Secondary cleaning / Destemmer
77 - Seeding X
78 - Spraying X
79 - Planting X
80 - Crop storage / Unloading X
82 - Front loader and bucket X X
83 - Telescopic single arm X X
84 - Booms, dippers and buckets X X
86 - Dozer blade and arm X X
88 - Accessories X X X X X
89 - Tools X X X X X
90 - Platform, cab, bodywork and decals X X X X

47998875B 21/05/2018
6
 INTRODUCTION

Chapters
Each Chapter is identified by a number e.g. Engine - Engine and crankcase - 10.001. The first number is identical
to the Section number i.e. Chapter 10.001 is inside Section 10, Engine. The second number is representative of the
Chapter contained within the Section.
CONTENTS
The Chapter Contents lists all the technical data (specifications), functional data (how it works), diagnostic data (fault
codes and troubleshooting), and service data (remove, install, adjust, etc.), that have been written in that Chapter for
that function or system on the machine.

Contents
ENGINE
ENGINE - Engine and crankcase – 10.001
TECHNICAL DATA
ENGINE - Engine and crankcase - General specification (10.001 - D.40.A.10) 4

FUNCTIONAL DATA

ENGINE - Engine and crankcase - Dynamic description (10.001 - C.30.A.10) 6

SERVICE
ENGINE - Engine and crankcase - Remove (10.001 -F.10.A.10) 8

DIAGNOSTIC
ENGINE - Engine and crankcase - Troubleshooting (10.001 - G.40.A.10) 10

INDEX
The Chapter Index lists in alphabetical order all the types of information (called information units) that have been
written in that Chapter for that function or system on the machine.

Index
ENGINE - 10
ENGINE
ENGINE - Engine and crankcase - Dynamic description (10.001 - C.30.A.10) 6

ENGINE - Engine and crankcase - General specification (10.001 - D.40.A.10) 4

ENGINE - Engine and crankcase - Remove (10.001 -F.10.A.10) 8

ENGINE - Engine and crankcase - Troubleshooting (10.001 - G.40.A.10) 10

47998875B 21/05/2018
7
 INTRODUCTION

Information units and information search

Each chapter is composed of information units. Each information unit has the SAP code shown in parentheses. This
indicates the function and type of information in that information unit. Each information unit has a page reference within
that Chapter. The information units provide a quick and easy way to find just the right piece of technical information
you are looking for.

Example information Engine block cover - Front – Remove (10.102.AP.01 - F.10.A.10)

unit
Information Unit SAP 10 102 AK 01 F 10.A.10
code
SAP code classification Engine Pan and covers Engine block Front Service data Remove
cover

NHIL12GEN0070A 1

Navigate to the correct information unit you are searching for by identifying the function and information type
from the SAP code.
• (1) Location and (2) Information type.
• (A) corresponds to the sections of the service manual.
(B) corresponds to the chapters of the service manual. After (B) there may be some additional information. In this
case it shows “.01”, which represents the “Front” block cover. These options may be front/rear, left/right, hydraulic/
mechanical etc.
(C) corresponds to the type of information listed in the chapter contents: Technical Data, Functional Data, Diagnos-
tic, or Service.
(A) and (B) are also shown in the page numbering on the page footer.
THE REST OF THE CODING IS NOT LISTED IN ALPHANUMERIC ORDER IN THIS MANUAL.
• You will find a table of contents at the beginning and end of each section and chapter.
You will find an alphabetical index at the end of each chapter.
• By referring to (A), (B) and (C) of the coding, you can follow the contents or index (page numbers) and quickly find
the information you are looking for.

Page header and footer

The page header will contain the following references:
• Section and Chapter description

The page footer will contain the following references:

• Publication number for that Manual.
• Version reference for that publication.
• Publication date
• Section, chapter, and page reference e.g. 10.102 / 9

47998875B 21/05/2018
8
 INTRODUCTION

Safety rules
D150B LA

Ecology and environment

Soil, air and water are vital factors of life in general. Disposing of waste improperly represents a danger for the
environment.
NOTE: Some recommendations must be followed:

• Obtain information about the correct methods to recycle or dispose of waste from local authorities, collection centers
or your dealer.
• Do not dispose of waste onto the ground, into drains, or in water beds.
• Do not fill reservoirs using cans or inappropriate pressurized fluid delivery systems, as they may cause considerable
spillage.
• Use sealed containers when draining the fluids. Do not use containers for food or beverages which may induce
ingestion.
• The air conditioning system is under pressure, and contains gases that should not be released into the atmosphere.
Do not disconnect or remove any component from the pressure line of the air conditioning system. If you need
repairs to the air conditioning system, contact a dealer.
• Immediately repair any leaks or defects in the machine's engine cooling and hydraulic systems.
• Generally avoid skin contact with any fuels, oils, fluids, acids, solvents, etc. Most of them contain substances which
may be harmful to your health.
• Avoid spills when draining fluid. Store them safely until they can be disposed of properly in compliance with local
legislation.
• Protect hoses and pipes during welding works, because the sparks generated during the welding work can damage
them, allowing the fluid to leak.

Mandatory recycling
The battery is essentially composed of lead plates and
sulfuric acid solution. Because the battery contains heavy
metals such as lead, resolution 401 de 2008 of CONAMA
orders that all used batteries must be returned to the bat-
tery dealer at the time of replacement. Do not dispose of
the battery in the garbage. Points of sale are obliged to
accept the return of your used battery, and to store it in a
suitable place and return it to the manufacturer for recy-
cling.

Improper disposal of batteries can contaminate the soil,

groundwater and waterways. Consumption of contami-
nated water can cause serious health risks. Contact of CUIL13TRO0091AA 1

the acid solution with the skin or eyes can cause serious
injury and blindness. In case of accidental contact with
the eyes or skin, immediately wash with running water and
seek emergency medical care.

47998875B 21/05/2018
9
 INTRODUCTION

Safety rules (Signal word definitions)

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

Personal Safety

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.

Throughout this manual and on machine safety signs, you will find the signal words DANGER, WARNING, and CAU-
TION followed by special instructions. These precautions are intended for your personal safety and for all those
involved in the work activity during operation of the machine.

Read and understand all the safety messages in this manual before you operate or service the machine.

DANGER:
Indicates an immediate danger that, if not avoided, will cause death or serious injury. The color associated
with Danger is RED.

WARNING:
Indicates a potential danger that, if not avoided, will cause serious injury. The color associated with Warning is
ORANGE.

CAUTION:
Indicates a potential danger that, if not avoided, can cause minor or moderate injury. ORANGE also alerts the
operator to unsafe practices. The color associated with Caution is YELLOW.

FAILURE TO FOLLOW DANGER, WARNING AND CAUTION MESSAGES COULD RESULT

IN DEATH OR SERIOUS INJURY.

Machine safety
NOTICE: Indicates a situation that, if not avoided, could result in machine or property damage. The color associated
with Notice is BLUE.

Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.

Information
NOTE: Indicates additional information which clarifies steps, procedures, or other information in this manual.

Throughout this manual you will find the word NOTE followed by additional information about a step, procedure or
other information in the manual. The word NOTE is not intended to address personal safety or property damage.

47998875B 21/05/2018
10
 INTRODUCTION

Safety rules
D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

Standard safety precautions

Be informed and notify personnel of the laws in force regulating safety, and provide documentation available for
consultation.
• Keep working areas as clean as possible.
• Ensure that working areas are provided with emergency boxes. They must be clearly visible and always contain
adequate sanitary equipment.
• Fire extinguishers must be properly identified and always be clear of obstructions. Their efficiency must be checked
on a regular basis and personnel must be trained on proper interventions and priorities.
• Keep all emergency exits free of obstructions and clearly marked.
• Smoking in working areas subject to fire danger must be strictly prohibited.

Prevention of injury
• Wear suitable work attire and safety glasses with no jewelry such as rings and chains when working close to engines
and equipment in motion.
• Wear safety gloves and goggles when performing the following operations:
• Topping off or changing lubrication oils.
• Using compressed air or liquids at a pressure greater than 2 bar (29 psi).
• Wear a safety helmet when working close to hanging loads or equipment working at head level.
• Always wear safety shoes and fitting clothes.
• Use protection cream for hands.
• Change wet clothes as soon as possible.
• In the presence of voltages exceeding 48 – 60 V, verify the efficiency of the ground and mass electrical connections.
Ensure that hands and feet are dry and use isolating foot boards. Workers should be properly trained to work with
electricity.
• Do not smoke or start an open flame close to batteries and any fuel material.
• Place soiled rags with oil, diesel fuel or solvents in specially provided anti-fire containers.
• Do not use any tool or equipment for any use other than what it was originally intended for. Serious injury may
occur.
• If running an engine indoors, make sure there is a sufficient exhaust fan in use to eliminate exhaust fumes.

During maintenance
• Never open the filler cap of the cooling system when the engine is hot. High temperature liquid at operating pressure
could result in serious danger and risk of burn. Wait until the temperature decreases under 50 °C (122 °F).
• Never add coolant to an overheated engine and use only appropriate liquids.
• Always work when the engine is turned off. Certain circumstances require maintenance on a running engine. Be
aware of all the risks involved with such an operation.
• Always use adequate and safe containers for engine fluids and used oil.
• Keep engine clean of any spilled fluids such as oil, diesel fuel, and or chemical solvents.
• Use of solvents or detergents during maintenance may emit toxic vapors. Always keep working areas aerated.
Wear a safety mask if necessary.
• Do not leave soiled rags that may contain any flammable substances close to the engine.
• Always use caution when starting an engine after any work has been performed. Be prepared to cut off intake air
in case of engine runaway.

47998875B 21/05/2018
11
 INTRODUCTION

• Never disconnect the batteries while the engine is running.

• Disconnect the batteries prior to performing any work on the equipment.
• Disconnect the batteries to place a load on them with a load tester.
• After any work is performed, verify that the battery clamp polarity is correct and that the clamps are tight and safe
from accidental short circuit and oxidation.
• Before disconnecting any pipelines (pneumatic, hydraulic, fuel pipes, etc.), verify that all pressure has been re-
leased. Take all necessary precautions bleeding and draining residual pressure. Always wear the proper safety
equipment.
• Do not alter the lengths of any wires.
• Do not connect any electronic service tool to the engine electrical equipment unless specifically approved by NEW
HOLLAND CONSTRUCTION.
• Do not modify the fuel system or hydraulic system unless approved by NEW HOLLAND CONSTRUCTION. Any
unauthorized modification will compromise warranty assistance and may affect engine operation and life span.

For engine equipped with an electronic control unit

• Do not weld on any part of the equipment without removing the control unit.
• Remove the in case of work requiring heating over 80 °C (176 °F).
• Do not paint the components and the electronic connections.
• Do not alter any data filed in the electronic control unit driving the engine. Any manipulation or alteration of electronic
components will void engine warranty assistance and may affect the correct working order and life span of the
engine.

Respect of the Environment

• Respect of the environment should be of primary importance. Take all necessary precautions to ensure personnel's
safety and health.
• Inform the personnel of the laws regarding the dispensing of used engine fluids.
• Handle batteries with care, storing them in a well ventilated environment and within anti-acid container.

47998875B 21/05/2018
12
 INTRODUCTION

Safety rules (Weld works)

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

WARNING
Avoid injury!
When welding, always wear proper protective equipment and welding clothing. All persons in the
work area must, at minimum, wear welding goggles. Never look directly at the welding arc without
welding eye protection.
Failure to comply could result in death or serious injury.
W1178A

NOTICE: Repair works with welding must be performed by a qualified and experienced welder. Appropriate safety
regulations should be followed by the personnel involved in the work. The time to perform welding operations depends
on the quality and precision of the work. Never make modifications on the machine.
To perform welding operations on the machine
(authorized and in accordance with NEW HOLLAND
CONSTRUCTION recommendations), proceed as
follows:
• Identify all points of fracture or cracking, and the areas
in which welding is required.
• Thoroughly clean the areas involved.
• Remove all paint. Inspect the parts with liquid penetrant
or a magnetic tool for particles.
• Shut down the engine. Place the ignition key in the
“OFF” position to shut down the engine.
SP0064 1
NOTICE: After you shut down the machine, wait at least
8 min to shut down the battery cables or the master
switch (if equipped). This time is necessary so that the
engine’s electronic system (if equipped) can store the
settings data in the electronic module.
• Disconnect the batteries and the wires from terminals
D+ and B+ of the alternator.
• Disconnect the electrical wiring harnesses from the
transmission control modules and from the engine.

• Connect the ground cable of the welding machine to the

component to be welded.
• Always connect the welding equipment to the frame that
is being welded.
• Never connect the welding equipment ground to a com-
ponent of the hydraulic system.
• Avoid welding at low temperatures, e.g., below 16 °C. If
necessary, warm up the part involved prior to welding.
• Remove the paint from all surfaces before heating or
welding. Painted surfaces can generate toxic gases
when heated or welded.
• Use appropriate masks or protective goggles.
• Wear appropriate gloves and protective equipment.
• Disconnect the connectors from all control modules of
the machine.

47998875B 21/05/2018
13
 INTRODUCTION

Heating lines containing pressurized fluid

NOTICE: Flammable sprays can be generated by heating near lines containing pressurized fluid, resulting in severe
burns to those doing the repair and to bystanders.
• Do not cause heating by welding, or use open flames
near the components containing pressurized fluid or
other flammable materials.
• Install temporary fire protection to protect the lines and
other components of the machine when you perform a
welding procedure.
NOTE: Pressurized lines can be accidentally cut when
the heat goes beyond the area of the flame.
• Avoid heating lines containing flammable fluids
• Do not weld or torch cut lines that contain flammable
fluids.
SP0059 2
• Clean the lines to be welded or cut with non-flammable
solvents before welding or cutting them.

Remove the paint before welding or heating

NOTICE: Hazardous fumes can be generated when the paint is heated by the welding arc or torch flame. If inhaled,
these fumes may be harmful to your health.
• Do not breath in potentially toxic fumes and dust.
• Do all such work outside or in a well-ventilated area.
• Handle and dispose of waste from paints or solvents in
accordance with environmental regulations, laws, and
government codes.
• Remove the paint from the part to be welded before
welding or heating operations.
• When sanding or grinding the paint, avoid breathing in
the dust.
• Wear an approved respirator.
• If you use solvent or paint stripper, remove the stripper SP0060 3
with soap and water before welding operations.
• Remove solvent or paint stripper containers and other
flammable material from area.
• Allow the fumes to disperse for at least 15 min before
welding or heating operations.

47998875B 21/05/2018
14
 INTRODUCTION

Safety rules - (Machine service)

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

NOTICE: Carefully read the Operation and Maintenance Manual before you turn on, operate, perform maintenance,
fuel, or repair the machine in any way.

Safe maintenance
• Unexpected machine movement can cause serious in-
jury.
• Place a “Do Not Operate” tag on the ignition key before
you start any maintenance procedure on the machine.
• Observe, understand, and follow the instructions on all
safety decals on the machine. If you have any ques-
tions, see the “Safety Decals” section in this manual.
• Keeps all safety signs and decals clean and legible.
NOTE: Replace decals that are unreadable, damaged, or
missing, as required.

SP0043 1

• Never allow unauthorized persons without training or

knowledge of the machine to perform maintenance
tasks.
• Follow all of the recommended maintenance and ser-
vice procedures.
• Do not leave the operator's seat if the operation requires
that the engine remains on. If necessary, call another
person to assist you in the verification procedure with
the machine in operation.
• Keep all machine components in good condition and
installed correctly.
• Immediately repair any fault. SP0039 2

• Replace worn or failed components.

• Remove grease, oil, and accumulated debris.

Moving parts
• Keep hands and clothing away from moving parts.
• Do not wear rings, wrist watches, jewellery, loose or
hanging garments, such as ties, torn clothing, scarves,
unbuttoned or unzipped jackets that can get caught by
movements of rotating components.

SP0041 3

47998875B 21/05/2018
15
 INTRODUCTION

Maintenance with the engine in operation

• Do not perform any maintenance operation with the en-
gine running.
• Contact with moving parts can cause serious injuries.
• Stop the engine and wait for it to cool off prior to per-
forming maintenance operations.
NOTE: If the engine must be on to make certain adjust-
ments, first place the transmission into neutral. Apply the
parking brake. Place the implement in a safe position.
Securely block the wheels. Use extreme caution.

SP0042 4

Protective equipment
• Familiarize yourself with the safety and protection reg-
ulations.
• Always wear certified safety equipment such as: hard
hat, no-slip footwear, protective gloves (to handle
chains and cables), ear protection, protective goggles,
reflector vests, and respirators when required.

SP0005 5

Support cradles
• Do not use the control levers or hydraulic hoses as sup-
ports.
• The hydraulic hoses and the control levers are movable
parts. The hydraulic hoses and the control levers do not
provide solid support. Also, the control levers can be
moved inadvertently and cause unexpected movement
of the machine or its attachments.
• Do not jump on or off the machine. Always maintain at
least three points of support between the steps and the
handrails.
• Always keep the operator’s compartment, steps,
handrails and control handles clean and clear of foreign
objects, oil, grease, mud or snow to reduce the risk of
slipping or stumbling.
• Remove mud or grease from your shoes before enter-
ing the cab to operate the machine.

47998875B 21/05/2018
16
 INTRODUCTION

Support, block, and protect the machine properly

• Do not perform maintenance work on a machine that is
not properly supported.
• Always support the implement on the ground before
starting the maintenance work.
• If it is necessary to perform maintenance on a machine
with the implement raised, make sure to support it
firmly.
• Do not support the machine on bricks, boards or other
material that could collapse under load.
• Do not perform maintenance work on a machine that is
supported solely by a jack.
• Lock the machine components that must be raised for SP0040 6

maintenance using appropriate lifting equipment.

• Always lock all moving components or parts of the ma-
chine that should be lifted for maintenance purposes
using adequate external lifting equipment as required
by local regulations.
• Do not allow anyone to pass or remain near or below a
raised attachment.
NOTE: Never move or stop the bucket above people or
a cab of another machine or truck.

• When the maintenance to be performed requires ac-

cess to areas that cannot be reached from the ground,
use a ladder or scaffolding.
• Workshop maintenance or field scaffolding should be
manufactured and maintained in accordance with the
safety regulations.
NOTE: If a ladder or scaffolding are not available, use
the machine handrails and steps.
• Perform any maintenance work with the greatest care
and attention.
• Do not place your head, body, limbs, hands, feet, or
fingers near the articulated cutting edges without the
necessary protection.
• Securely block the machine or any component that may
fall before working on the machine or component. If
possible, also use an auxiliary or backup blocking de-
vice.
NOTE: To prevent unexpected movement, securely
block the working elements whenever you service or
replace working tool parts such as cutting edges.

47998875B 21/05/2018
17
 INTRODUCTION

Safe storage of accessories

• Accessories such as buckets, hydraulic brakes and
blades stored incorrectly can fall and cause serious
injury or death.
• Store accessories and implements safely to prevent
falling.
• Keep accessories and implements stored in safe loca-
tions without the circulation of people.

SP0054 7

Be careful with any debris that comes off

• Serious injury may occur if your eyes or any other part
of the body are struck by flying debris.
• Protect yourself from injury caused by parts or debris
that may be thrown; use protective goggles or a face
shield.
• Keep people away from the work area before you per-
form any maintenance on the machine.

SP0056 8

Use appropriate tools

• Use tools appropriate for the work to be performed.
• Inappropriate tools, parts and procedures may create
dangerous conditions.
• Use tools of correct dimensions in the fastening ele-
ments.
NOTE: Avoid injuries caused by an improper wrench.
• Do not use tools sized in inches with metric bolts and
nuts, or vice-versa.
• Only use genuine parts (See the Parts Catalog).

SP0063 9

47998875B 21/05/2018
18
 INTRODUCTION

Dispose of waste correctly

• Disposing of waste improperly represents a danger for
the environment.
• Potentially dangerous material used in the machines
includes lubricants, fuel, coolant, brake fluid, filters, and
batteries.
• Use sealed containers when draining the fluids.
• Do not use containers for food or beverages which may
induce ingestion.
• Do not dispose of waste onto the ground, into drains, or
in water beds.
• Obtain information about the correct methods to recy-
cle or dispose of waste from local authorities, collection SP0044 10

centers or your dealer.

• Keep the maintenance area clean and dry at all times.

• Clean all spills of water, fluid or fuel immediately.

• Do not pile up rags soiled with fluid or grease. This is a
fire hazard. Store soiled rags in closed metal contain-
ers.
• Rust and corrosion inhibitors are volatile and
flammable.
• Prepare parts in well-ventilated areas.
• Keep flames away. Do not smoke.
• Store containers of fluids in cool and well-ventilated
areas where they cannot be reached by unauthorized
people.

Properly light the work area

• Properly and safely light the working area.
• Use portable safety lights to work inside and under the
machine.
• Make sure that the bulb is protected by a cage.
• The incandescent filament of the bulb can accidentally
cause a fire if it comes into contact with fuel or oil.

SP0045 11

47998875B 21/05/2018
19
 INTRODUCTION

Keep the machine clean

• Keep the machine clean and free of debris, excess lu-
bricants, and spilled fuel and fluids.
• Do not spray water or steam inside the cab.
• Use approved solvents, detergents and water to clean
the machine and its components on a regular basis.
• Keep the engine compartment, air conditioning con-
denser, radiator, batteries, hydraulic lines, fuel tank,
and operator’s cab clean.
• After shutting down the engine, the engine compart-
ment temperature can rise rapidly.
• Be careful with possible fires.
SP0053 12
• Open the access doors to speed up the engine cooling
process and clean the compartment.

SP0050 13

Battery maintenance precautions

• Disconnect the batteries before you perform any type
of service on the electrical system.
NOTE: Familiarize yourself with the battery cable dis-
connection sequence and the disconnection sequence
of other electrical and electronic components before
you start the service procedure.
• The sulfuric acid contained in the battery is poisonous.
The acid is strong enough to scald the skin, corrode
clothes and cause blindness if it comes into contact with
the eyes.
NOTE: Wash your eyes with water for 15 min in the
event of contact. See a doctor immediately. SP0055 14

• Always top up the battery electrolyte level in ventilated

areas.
• Wear eye protections and rubber gloves.
• Avoid breathing the electrolyte vapors when topping up
the electrolyte level.
• Avoid spilling or splashing the machine with the elec-
trolyte.
• Use the correct emergency start-up method.
• In case of contact with the acid, thoroughly wash the
affected part with water. Place baking soda or clay on
the area to help neutralize the acid.

47998875B 21/05/2018
20
 INTRODUCTION

Avoid a battery explosion

• The gas released by the batteries can be flammable
and may explode.
• Keep sparks, matches and flames away from the bat-
teries.
• Never short-circuit the battery terminals to check their
charge. Use a voltmeter.
• Do not charge a frozen battery, as it may explode.
• Warm the battery to 16.0 °C (60.8 °F) before you charge
the battery.
• Battery electrolyte is poisonous.
• If the battery explodes, the electrolyte can reach the SP0052 15
eyes with consequent risk of blindness.
• Be sure to wear eye protection.

Avoid burns
• After machine operation, the engine coolant is hot and
under pressure.
• The engine, radiator, and cooling system lines contain
hot water and steam.
• Skin contact with hot water or steam can cause severe
burns.
• Avoid possible burns that may be caused by hot water
or steam under pressure.
• Do not remove the radiator cap until the engine is cool.
• After the engine has cooled, turn the cap slowly to allow
all the pressure to be released. We advise you to wear
safety goggles and gloves to perform this operation. SP0049 16

• After the pressure is released, remove the cap com-

pletely.
• The hydraulic fluid reservoir is under pressure.
• Be sure to release all pressure before removing the cap.
• Engine oil, reducer oil and hydraulic fluid also become
hot during operation.
• Like the engine, the pressure lines and lubrication sys-
tem components are also heated during machine oper-
ation.
• In case of maintenance in any of these components,
wait until the system completely cools.
• Wait until all the fluids and components cool before
starting any maintenance work.

47998875B 21/05/2018
21
 INTRODUCTION

Be careful with pressurized fluids

• Fuel or hydraulic fluid under pressure can penetrate
the skin or eyes, causing serious injuries, blindness, or
death.
• Avoid this hazard by releasing the pressure from the
systems before disconnecting the hydraulic or fuel
lines.
• Tighten all connections before pressurizing the sys-
tems.
• Search for leaks with a piece of cardboard or wood,
taking care to protect the hands and body from high
pressure fluids.
• Wear a face shield or protective goggles to protect the
eyes.
• If an accident occurs, see a doctor immediately.
• Any fluid injected into the skin must be treated quickly
to avoid major health problems.
• Never perform repairs on pressurized components until
the pressure has been released.
• Use extreme caution when you remove the radiator,
the expansion tank or the covers, the drain plugs, the
grease fittings, or other pressure components.
• Park the machine and let it cool before opening a pres-
surized tank.
• Release all pressure before you work on systems with SP0046 17
an accumulator.

• Hydraulic fluid or diesel fuel that leaks under pressure

can penetrate the skin and cause infection or other in-
juries.
NOTE: To prevent personal injury, relieve all pressure
before disconnecting fluid lines or performing work on
the hydraulic system.
• Before applying pressure, make certain all connections
are tight and components are in good condition.
• Use a piece of cardboard, newspaper, or wood to check
for any pressurized leaks to prevent fluid penetrating
the skin.
• Unexpected movement of the machine could occur.

47998875B 21/05/2018
22
 INTRODUCTION

Torque
D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

Non-flanged metric fasteners

Bolt 8.8 Class Bolt 10.9 Class
and nut class 8 and nut class 10 Jam nut CL Jam nut CL
Nominal size Zinc- and Zinc- and 0.8 with bolt 0.10 with bolt
Unplated chrome- Unplated chrome- CL 8.8 CL 10.9
plated plated
2.2 N·m 2.9 N·m 3.2 N·m 4.2 N·m 2 N·m 2.9 N·m
M4
(19 lb in) (26 lb in) (28 lb in) (37 lb in) (18 lb in) (26 lb in)
4.5 N·m 5.9 N·m 6.4 N·m 8.5 N·m 4 N·m 5.8 N·m
M5
(40 lb in) (52 lb in) (57 lb in) (75 lb in) (36 lb in) (51 lb in)
7.5 N·m 10 N·m 11 N·m 15 N·m 6.8 N·m 10 N·m
M6
(66 lb in) (89 lb in) (96 lb in) (128 lb in) (60 lb in) (89 lb in)
18 N·m 25 N·m 26 N·m 35 N·m 17 N·m 24 N·m
M8
(163 lb in) (217 lb in) (234 lb in) (311 lb in) (151 lb in) (212 lb in)
37 N·m 49 N·m 52 N·m 70 N·m 33 N·m 48 N·m
M10
(27 lb ft) (36 lb ft) (38 lb ft) (51 lb ft) (25 lb ft) (35 lb ft)
64 N·m 85 N·m 91 N·m 121 N·m 58 N·m 83 N·m
M12
(47 lb ft) (63 lb ft) (67 lb ft) (90 lb ft) (43 lb ft) (61 lb ft)
158 N·m 210 N·m 225 N·m 301 N·m 143 N·m 205 N·m
M16
(116 lb ft) (155 lb ft) (166 lb ft) (222 lb ft) (106 lb ft) (151 lb ft)
319 N·m 425 N·m 440 N·m 587 N·m 290 N·m 400 N·m
M20
(235 lb ft) (313 lb ft) (325 lb ft) (433 lb ft) (214 lb ft) (295 lb ft)
551 N·m 735 N·m 762 N·m 1016 N·m 501 N·m 693 N·m
M24
(410 lb ft) (500 lb ft) (560 lb ft) (750 lb ft) (370 lb ft) (510 lb ft)

NOTE: The torque specifications in English units for M4 to M8 fastening elements are shown in pounds-inches. The
torque specifications in English units for M10 to M24 fastening elements are shown in pounds-feet.

47998875B 21/05/2018
23
 INTRODUCTION

Flanged metric fasteners

Bolt 8.8 Class Bolt 10.9 Class
and nut class 8 and nut class 10 Jam nut CL Jam nut CL
Nominal size Zinc- and Zinc- and 0.8 with bolt 0.10 with bolt
Unplated chrome- Unplated chrome- CL 8.8 CL 10.9
plated plated
2.4 N·m 3.2 N·m 3.5 N·m 4.6 N·m 2.2 N·m 3.1 N·m
M4
(21 lb in) (28 lb in) (31 lb in) (41 lb in) (19 lb in) (27 lb in)
4.9 N·m 6.5 N·m 7.0 N·m 9.4 N·m 4.4 N·m 6.4 N·m
M5
(43 lb in) (58 lb in) (62 lb in) (83 lb in) (39 lb in) (57 lb in)
8.3 N·m 11 N·m 12 N·m 16 N·m 7.5 N·m 11 N·m
M6
(73 lb in) (96 lb in) (105 lb in) (141 lb in) (66 lb in) (96 lb in)
20 N·m 27 N·m 29 N·m 39 N·m 18 N·m 27 N·m
M8
(179 lb in) (240 lb in) (257 lb in) (343 lb in) (163 lb in) (240 lb in)
40 N·m 54 N·m 57 N·m 77 N·m 37 N·m 53 N·m
M10
(30 lb ft) (40 lb ft) (42 lb ft) (56 lb ft) (27 lb ft) (39 lb ft)
70 N·m 93 N·m 100 N·m 134 N·m 63 N·m 91 N·m
M12
(52 lb ft) (69 lb ft) (74 lb ft) (98 lb ft) (47 lb ft) (67 lb ft)
174 N·m 231 N·m 248 N·m 331 N·m 158 N·m 226 N·m
M16
(128 lb ft) (171 lb ft) (183 lb ft) (244 lb ft) (116 lb ft) (167 lb ft)
350 N·m 467 N·m 484 N·m 645 N·m 318 N·m 440 N·m
M20
(259 lb ft) (345 lb ft) (357 lb ft) (476 lb ft) (235 lb ft) (325 lb ft)
607 N·m 809 N·m 838 N·m 1118 N·m 552 N·m
M24
(447 lb ft) (597 lb ft) (618 lb ft) (824 lb ft) (407 lb ft)

Metric hexagonal bolts, classes 5.6 and higher

(1) Manufacturer's Identification

(2) Property Class

COIL14DOZ0004AA 1

Metric hexagonal nuts and jam nuts, classes 05 and up

(1) Manufacturer's Identification

(2) Property Class

(3) Clock marking of property class and manufacturer’s

identification (optional), i.e. marks 60° apart indicate
Class 10 properties and marks 120° apart indicate Class
8.

COIL14DOZ0005AA 2

47998875B 21/05/2018
24
 INTRODUCTION

Non-flanged fasteners in inches

Bolt and nut Bolt and nut
class SAE 5 class SAE 8
Jam nut GrB Jam nut GrC
Nominal size Gold-, Zinc- Gold-, Zinc-
Unplated or Unplated or with bolt Gr5 with bolt Gr8
and Chrome- and Chrome-
silver-plated silver-plated
plated plated
8 N·m 11 N·m 12 N·m 16 N·m 8.5 N·m 12.2 N·m
1/4
(71 lb in) (97 lb in) (106 lb in) (142 lb in) (75 lb in) (109 lb in)
17 N·m 23 N·m 24 N·m 32 N·m 17.5 N·m 25 N·m
5/16
(150 lb in) (204 lb in) (212 lb in) (283 lb in) (155 lb in) (220 lb in)
30 N·m 40 N·m 43 N·m 57 N·m 31 N·m 44 N·m
3/8
(22 lb ft) (30 lb ft) (31 lb ft) (42 lb ft) (23 lb ft) (33 lb ft)
48 N·m 65 N·m 68 N·m 91 N·m 50 N·m 71 N·m
7/16
(36 lb ft) (48 lb ft) (50 lb ft) (67 lb ft) (37 lb ft) (53 lb ft)
74 N·m 98 N·m 104 N·m 139 N·m 76 N·m 108 N·m
1/2
(54 lb ft) (73 lb ft) (77 lb ft) (103 lb ft) (56 lb ft) (80 lb ft)
107 N·m 142 N·m 150 N·m 201 N·m 111 N·m 156 N·m
9/16
(79 lb ft) (105 lb ft) (111 lb ft) (148 lb ft) (82 lb ft) (115 lb ft)
147 N·m 196 N·m 208 N·m 277 N·m 153 N·m 215 N·m
5/8
(108 lb ft) (145 lb ft) (153 lb ft) (204 lb ft) (113 lb ft) (159 lb ft)
261 N·m 348 N·m 369 N·m 491 N·m 271 N·m 383 N·m
3/4
(193 lb ft) (257 lb ft) (272 lb ft) (362 lb ft) (200 lb ft) (282 lb ft)
420 N·m 561 N·m 594 N·m 791 N·m 437 N·m 617 N·m
7/8
(310 lb ft) (413 lb ft) (438 lb ft) (584 lb ft) (323 lb ft) (455 lb ft)
630 N·m 841 N·m 890 N·m 1187 N·m 654 N·m 924 N·m
1
(465 lb ft) (620 lb ft) (656 lb ft) (875 lb ft) (483 lb ft) (681 lb ft)

Bolts in inches and self-locking nuts (Class SAE)

20083682 3

(1) Class 2 bolt - No Marks

(2) Class 5 bolt - Three marks

(3) Class 8 bolt - Five marks

(4) Class 2 nut - No Marks

(5) Class 5 Nut - Marks 120° apart

(6) Class 8 Nut - Marks 60° apart

47998875B 21/05/2018
25
 INTRODUCTION

Self-locking nuts in inches, all-metal (three optional methods)

Grade A
(1) Corner marking method: No notches
(2) Flats marking method: No marks
(3) Clock marking method: No marks

Grade B
(1) Corner marking method: One circumferential notch
(2) Flats marking method: Letter B
(3) Clock marking method: Three marks

Grade C
(1) Corner marking method: Two circumferential notches
20090268 4
(2) Flats marking method: Letter C
(3) Clock marking method: Six marks

47998875B 21/05/2018
26
 INTRODUCTION

Torque - Standard torque data for hydraulics

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

Installation of adjustable fittings in straight

thread O-ring bosses

1. Lubricate the O-ring by coating it with a light oil or

petroleum. Install the O-ring in the groove adjacent
to the metal backup washer which is assembled at the
extreme end of the groove (4).
2. Install the fitting into the SAE straight thread boss until
the metal backup washer contacts the face of the boss
(5).
NOTE: Do not over tighten and distort the metal
backup washer. 23085659 1
3. Position the fitting by turning out (counterclockwise)
up to a maximum of one turn. Holding the pad of the
fitting with a wrench, tighten the locknut and washer
against the face of the boss (6).

Standard torque data for hydraulic tubes and fittings

Tube nuts for 37° flared fittings O-ring boss plugs
adjustable fitting
locknuts, swivel JIC-
37° seats
Size Tubing OD Thread Torque Torque
size
4 6.4 mm (1/4 in) 7/16-20 12 – 16 N·m (9 – 12 lb ft) 8 – 14 N·m (6 – 10 lb ft)
5 7.9 mm (5/16 in) 1/2-20 16 – 20 N·m (12 – 15 lb ft) 14 – 20 N·m (10 – 15 lb ft)
6 9.5 mm (3/8 in) 9/16-18 29 – 33 N·m (21 – 24 lb ft) 20 – 27 N·m (15 – 20 lb ft)
8 12.7 mm (1/2 in) 3/4-16 47 – 54 N·m (35 – 40 lb ft) 34 – 41 N·m (25 – 30 lb ft)
10 15.9 mm (5/8 in) 7/8-14 72 – 79 N·m (53 – 58 lb ft) 47 – 54 N·m (35 – 40 lb ft)
12 19.1 mm (3/4 in) 1-1/16-12 104 – 111 N·m (77 – 82 lb ft) 81 – 95 N·m (60 – 70 lb ft)
14 22.2 mm (7/8 in) 1-3/16-12 122 – 136 N·m (90 – 100 lb ft) 95 – 109 N·m (70 – 80 lb ft)
16 25.4 mm (1 in) 1-5/16-12 149 – 163 N·m (110 – 120 lb ft) 108 – 122 N·m (80 – 90 lb ft)
20 31.8 mm (1-1/4 in) 1-5/8-12 190 – 204 N·m (140 – 150 lb ft) 129 – 158 N·m (95 – 115 lb ft)
24 38.1 mm (1-1/2 in) 1-7/8-12 217 – 237 N·m (160 – 175 lb ft) 163 – 190 N·m (120 – 140 lb ft)
32 50.8 mm (2 in) 2-1/2-12 305 – 325 N·m (225 – 240 lb ft) 339 – 407 N·m (250 – 300 lb ft)

These torques are not recommended for tubes of 12.7 mm (1/2 in) OD and larger with wall thickness of 0.889 mm
(0.035 in) or less. The torque is specified for 0.889 mm (0.035 in) wall tubes on each application individually.

Before installing and torquing 37° flared fittings, clean the face of the flare and threads with a clean solvent or Loctite
cleaner and apply hydraulic sealant LOCTITE® 569™ to the 37° flare and the threads.

Install fitting and torque to specified torque, loosen fitting and retorque to specifications.

47998875B 21/05/2018
27
 INTRODUCTION

Pipe thread fitting torque Thread size Torque (maximum)

1/8-27 13 N·m (10 lb ft)
Before installing and tightening pipe fittings, clean the
1/4-18 16 N·m (12 lb ft)
threads with a clean solvent or Loctite cleaner and apply
sealant LOCTITE® 567™ PST PIPE SEALANT for all fittings 3/8-18 22 N·m (16 lb ft)
including stainless steel or LOCTITE® 565™ PST for 1/2-14 41 N·m (30 lb ft)
most metal fittings. For high filtration/zero contamination 3/4-14 54 N·m (40 lb ft)
systems use LOCTITE® 545™.

Installation of ORFS (O-Ring Flat Seal fit-

tings)
When installing ORFS fittings thoroughly clean both flat
surfaces of the fittings (1) and lubricate the O-ring (2) with
light oil. Make sure both surfaces are aligned properly.
Torque the fitting to specified torque listed throughout the
repair manual.
NOTICE: If the fitting surfaces are not properly cleaned,
the O-ring will not seal properly. If the fitting surfaces are
not properly aligned, the fittings may be damaged and will
not seal properly.
NOTICE: Always use genuine factory replacement oils
50011183 2
and filters to ensure proper lubrication and filtration of en-
gine and hydraulic system oils.

The use of proper oils, grease, and keeping the hydraulic

system clean will extend machine and component life.

47998875B 21/05/2018
28
 INTRODUCTION

Basic instructions - Shop and assembly

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

Shimming
For each adjustment operation, select adjusting shims and measure the adjusting shims individually using a microm-
eter, then add up the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, or
the rated value shown on each shim.

Rotating shaft seals

For correct rotating shaft seal installation, proceed as follows:
1. Before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes.
2. Thoroughly clean the shaft and check that the working surface on the shaft is not damaged.
3. Position the sealing lip facing the fluid.
NOTE: With hydrodynamic lips, take into consideration the shaft rotation direction and position the grooves so that
they will move the fluid towards the inner side of the seal.
4. Coat the sealing lip with a thin layer of lubricant (use oil rather than grease). Fill the gap between the sealing lip
and the dust lip on double lip seals with grease.
5. Insert the seal in its seat and press down using a flat punch or seal installation tool. Do not tap the seal with a
hammer or mallet.
6. While you insert the seal, check that the seal is perpendicular to the seat. When the seal settles, make sure that
the seal makes contact with the thrust element, if required.
7. To prevent damage to the seal lip on the shaft, position a protective guard during installation operations.

O-ring seals
Lubricate the O-ring seals before you insert them in the seats. This will prevent the O-ring seals from overturning and
twisting, which would jeopardize sealing efficiency.

Sealing compounds
Apply a sealing compound on the mating surfaces when specified by the procedure. Before you apply the sealing
compound, prepare the surfaces as directed by the product container.

Spare parts
Only use CNH Original Parts or NEW HOLLAND CONSTRUCTION Original Parts.

Only genuine spare parts guarantee the same quality, duration, and safety as original parts, as they are the same
parts that are assembled during standard production. Only CNH Original Parts or NEW HOLLAND CONSTRUCTION
Original Parts can offer this guarantee.

When ordering spare parts, always provide the following information:

• Machine model (commercial name) and Product Identification Number (PIN)
• Part number of the ordered part, which can be found in the parts catalog

47998875B 21/05/2018
29
 INTRODUCTION

Protecting the electronic and/or electrical systems during charging and welding
To avoid damage to the electronic and/or electrical systems, always observe the following practices:
1. Never make or break any of the charging circuit connections when the engine is running, including the battery
connections.
2. Never short any of the charging components to ground.
3. Always disconnect the ground cable from the battery before arc welding on the machine or on any machine
attachment.
• Position the welder ground clamp as close to the welding area as possible.
• If you weld in close proximity to a computer module, then you should remove the module from the machine.
• Never allow welding cables to lie on, near, or across any electrical wiring or electronic component while you
weld.
4. Always disconnect the negative cable from the battery when charging the battery in the machine with a battery
charger.
NOTICE: If you must weld on the unit, you must disconnect the battery ground cable from the machine battery.
The electronic monitoring system and charging system will be damaged if this is not done.
5. Remove the battery ground cable. Reconnect the cable when you complete welding.
WARNING
Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush
with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large
quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.
Failure to comply could result in death or serious injury.
W0111A

Special tools
The special tools that NEW HOLLAND CONSTRUCTION suggests and illustrate in this manual have been specifically
researched and designed for use with NEW HOLLAND CONSTRUCTION machines. The special tools are essential
for reliable repair operations. The special tools are accurately built and rigorously tested to offer efficient and long-
lasting operation.

By using these tools, repair personnel will benefit from:

• Operating in optimal technical conditions
• Obtaining the best results
• Saving time and effort
• Working in safe conditions

47998875B 21/05/2018
30
 INTRODUCTION

Basic instructions (Daily inspection)

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

WARNING
Improper operation or service of this machine can result in an accident.
Read and understand the SAFETY INFORMATION Section before you perform any maintenance, ser-
vice, or repairs. Read and understand the specific service procedures for the components you plan
to work with before you start servicing the machine.
Failure to comply could result in death or serious injury.
W0138A

Every day, before starting work, it is necessary to inspect the machine and service certain of its components.

Overall
• Check for water or oil leaks.
• Check that all screws and nuts are correctly tightened.
• Wipe off any dust and clean off any accumulated debris (engine, operator's compartment, etc.).
• Check the tension and wear of the tracks.
• Check for damage.

Motor
• Check the oil level, and change the oil, if necessary.
• Check the level of coolant liquid.
• Check for clogging or damage to the radiator.
• Check the condition of the engine belts.
• Check whether the air filter restriction warning light is lit up on the instrument cluster.
• Check for water or oil leaks on the components.
• Check the condition of all fuel lines.
• Check the fuel level.

Others
• Check the hydraulic fluid level.
• Check that the hydraulic fluid is clean.
• Check the condition of all hydraulic lines.
• Check for electrical short-circuits.
• Check that all battery connections are properly tightened.
• Adjust the rear view mirrors.
• Check for fluid leaks in the cylinders.
• Check the condition of the implements.

After Starting the Engine

• Did the engine start correctly? Is the exhaust smoke normal? Any unusual noises?
• Check for abnormal noise on the hydraulic components.
• Check for water, fuel, or oil leaks on the components.
• Check the audible alarm devices, working lights and windshield wipers.
• Check that all hydraulic circuits are functioning correctly.

47998875B 21/05/2018
31
 INTRODUCTION

General specification
D150B LA

NOTE: All specifications are given according to SAE Standards or Recommended Practices where the specification
applies.

Specifications
Engine
Make & Model NEF 667TA/EDJ
Typè Diesel cycle, 4-stroke, water-cooled, electronic fuel
injection.
Cylinders 6
Weight 552.0 kg (1217.0 lb)
Firing order 1-5-3-6-2-4
Bore and travel 103.9 – 132.1 mm (4.09 – 5.20 in)
Volumetric displacement 6.7 l (409 in³)
Compression ratio 17: 1
Max nominal gross power @ 2200 RPM 116 kW (158 Hp)
Max. power net @ 2200 RPM 107.0 kW (145.5 Hp)
Max gross torque @ 1400 RPM 690 N·m (509 lb ft)

Engine Speeds
Maximum RPM without load 2350 RPM +/- 50 RPM
Maximum nominal speed 2200 RPM
Idle speed 900 – 1100 RPM
Gradeability (without losing the engine lubrication capacity) Longitudinal: 35°
Sideways: 45° maximum

Hydraulic System
Main Relief Pressure 20684 kPa (3000 psi)
Load Sensor Relief (pressure seen on diagnostic port)
Pump Capacity 34.9 US gpm @ 2830 psi @ 2200 RPM engine
132 l/min at 19500 kPa at 2200 kPa

Travel speeds
Speed forward Infinitely variable from 0.0 – 9.7 km/h (0.0 – 6.0 mph)
Reverse speed Infinitely variable from 0.0 – 9.7 km/h (0.0 – 6.0 mph)
Track pull (Maximum both tracks) 275105 N (61846 lb)

Power train
Transmission – manufacturer Rexroth
Transmission – type Dual drive hydrostatic
Transmission – filter type 4μm @ 75 ß replaceable with 100-mesh suction screen
Pumps – model AA4VTG
Pumps – type Variable volume pistons
Pumps – displacement 107 cm³
Motors – model AA6VM
Motors – type Variable tilt shaft
Motors – travel 140 cm³

Foot brakes
Steering brakes Hydrostatic
Parking brakes Spring-activated, pressure-released

47998875B 21/05/2018
32
 INTRODUCTION

Final drive
Final drives Primary reduction by helical gears and secondary by
planetary reducer
Total reduction 61.4 : 1

Fuel system
Fuel feed Common Rail
Fuel injection Six injectors
Principle of ignition Diesel Cycle
Fuel consumption 21.80 L/hour (5.76 US gal/hour)

Electrical system 24 Volt

Batteries Two 12V batteries in series
Battery capacity 650 A @ -17.8 °C (0.0 °F) for 90 seconds, without
letting the voltage fall below 1,0 V
Alternator Bosch 24 V, 65 A, with voltage regulator
Starter Motor Nippon Denso 7.5 kW, relay-activated

Travel speed and traction of track with SALT sealed and lubricated chain. If the machine is equipped with a track with
a ALT extended life chain, the speed will be reduced by 4% and the traction of the track will increase by 4%.

47998875B 21/05/2018
33
 INTRODUCTION

Tracks
D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]
D150B LA

General specification
Adjusting track tension Hydraulic
Track frame suspension Pivot shaft and oscillating equalizer beam
Track link pitch 190.0 mm (7.5 in)
Height of track shoe grouser 55.50 mm (2.19 in)
Track pin diameter 38.00 mm (1.50 in)
65.00 mm (2.56 in) or
Track bushing diameter
** 85.60 mm (3.37 in)
* 25 (5 segments of 5 teeth) or
Number of sprocket teeth
** 26 (13 segments of 2 teeth)
* 763.00 mm (30.04 in) or
Sprocket pitch
** 793.00 mm (31.22 in)
Reinforced box sections with replaceable sloped
Track frame
canopies
Track with SALT lubricated chain Standard
Track with ALT extended life chain Optional

Machines equipped with XLT extra-long chassis track

Number of track shoes per side 45
Number of upper rollers per side 2
Number of lower rollers per side 8
SF, DF, SF, DF, SF,
Roller flange configuration from sprocket
SF, DF, SF
171.50 mm
Upper roller diameter
(6.75 in)
203.00 mm
Lower roller diameter
(7.99 in)
3049.5 mm
Length of track on ground (track with standard SALT sealed and lubricated chain)
(120.1 in)
3025.8 mm
Length of track on ground (track with optional ALT extended life track
(119.1 in)
1880 mm
Tread
(74 in)
559 mm
Track shoe width
(22 in)
34093 cm²
559 mm (22 in) (***) track shoe
(5284 in²)
Ground pressure:
• tread of 1880 mm (74 in)
45.9 kPa (6.7 psi)
• PAT power arc of 3200 mm (126 in)
• 559 mm (22 in) track shoe

* .Values for track with standard SALT chain.

** .Values for track with optional ALT chain.
*** Area of track-on-ground, values for track with standard SALT chain (if the unit is equipped with track with
optional ALT chain, the on ground area is 8% less).
**** On-ground pressure values for track with standard SALT chain (if the unit is equipped with track with optional
ALT chain, the on-ground pressure is 1 psi less).

47998875B 21/05/2018
34
 INTRODUCTION

Overall dimensions
D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]
D150B LA

COIL14DOZ0164FA 1

Height and ground clearance dimensions

Machines equipped with XLT extra-long chassis track
(A) Top of exhaust stack 2884 mm (113.5 in)
(B) Blade height 1183 mm (46.6 in)
(C1) Clearance at belly pans (lowest) 347 mm (13.7 in)
(C2) Drawbar clearance 493 mm (19.4 in)
(C3) Clearance at center line of drawbar opening 543 mm (21.4 in)
(D) Shank height (transport position) (**) 341 mm (13.4 in)
(E) Top of seat headrest 2479 mm (97.6 in)
(F1) Height of cab with air conditioning 3002 mm (118.2 in)
(F2) Height of ROPS 3002 mm (118.2 in)

NOTE: (1) The ground clearance and overall height dimensions are with the grouser fully penetrated according to
SAE J1234 and with tracks with SALT sealed and lubricated chain. Add 55.5 mm (2.2 in) if the machine is on a rigid
surface.
NOTE: (**) Ripper transport with shank in the intermediate position.

47998875B 21/05/2018
35
 INTRODUCTION

RCIL10CWL145FAL 2

Length dimensions with blade straight

Machines equipped with XLT extra-long chassis track
(A) Overall length:
4065 mm (160.0 in)
No blade, no rear equipment, track with standard SALT chain)
(B) Overall length:
5410 mm (213.0 in)
Straight blade, no rear equipment
(C) Overall length:
5672 mm (223.3 in)
Blade straight, with drawbar
(D) Overall length:
6637 mm (261.3 in)
Blade straight, with ripper

NOTE: The values apply to machines equipped with track with standard SALT sealed and lubricated chain.
NOTE: Overall length with blade tilt angle at 57.5°. If the blade tilt is adjusted to 55°

47998875B 21/05/2018
36
 INTRODUCTION

RCIL10CWL147FAL 3

Dimensions of the machine for transport

Length and width of the machine for transport, with the blade tilt angle at 28°
Blade Width 3200 mm (126.0 in) 4000 mm (157.5 in)
(A) Width 2810.0 mm (110.6 in) 3525.0 mm (138.8 in)
(B) Length without drawbar 6085.0 mm (239.6 in) 6306.0 mm (248.3 in)

Add 262 mm (10.3 in) for drawbar.

Add 1227 mm (48.3 in) for the ripper.

47998875B 21/05/2018
37
 INTRODUCTION

Ripper
D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]
D150B LA

Ripper operating data and dimension

Overall length in transport position 5973.0 mm (235.2 in)
Overall length with ripper shank resting on the ground
6131.0 mm (241.4 in)
line
Lifting Excavation
Ripper shanks in top position
424.0 mm (16.7 in) 310.0 mm (12.2 in)
Lifting Excavation
Ripper shank in mid position
343.0 mm (13.5 in) 394.0 mm (15.5 in)
Lifting Excavation
Ripper shank in bottom position
262.0 mm (10.3 in) 478.0 mm (18.8 in)

Two hydraulic cylinders (dual action)

Control type 101.6 mm (4.0 in) diameter X 254.0 mm (10.0 in) stroke
X 50.8 mm (2.0 in) rod
Overall width (Maximum) 1712 mm (67.4 in)
Width of cut (Maximum) 1636 mm (64.4 in)
Number of teeth (Standard) 3
Number of teeth (Maximum) 3
Width of shank
Tooth width
Digging depth 478 mm (18.8 in)
Ground clearance (Lowest position transport) 302 mm (11.9 in)
Torque (rear mounted equipment) 705 – 1165 N·m (520.0 – 859.3 lb ft)

NOTE: Lift and dig dimensions are with the grouser fully penetrated according to SAE J1234. Add 52.6 mm (2.07 in)
if unit is on rigid surface.

47998875B 21/05/2018
38
 INTRODUCTION

Machine weights
D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]
D150B LA

Operating weight
Machines equipped with:
• extra long chassis track XLT
• tread of 1880 mm (74 in) 15985 kg (35241 lb)
• PAT power arc of 3200 mm (126 in)
• 559 mm (22 in) track shoe
Operating weight includes ROPS, full fuel and hydraulic tanks, 77 kg (170 lb) operator, SALT track with chain, front
pull hook, rear lift system, track guides, backup alarm, horn, lights, track shoes, C frame and blade (width as shown).

Transport weight
Machines equipped with:
• extra long chassis track XLT
11368 kg (25062 lb)
• tread of 1880 mm (74 in)
• PAT power arc of 3200 mm (126 in)
Transport weight includes base machine weight, 57 l (15 US gal) fuel, full hydraulic system, front pull hook, frame
and blade as indicated. Add for rear-mounted equipment, drive sprocket and tracks, ROPS canopy or cab and
any optional equipment.

Equipment
Retrieval hitch 23 kg (51 lb)
Drawbar
3200 mm (126 in) blade 920 kg (2028 lb)
3-tooth ripper and 4-spool valve 1600 kg (3527 lb)
Track with SALT sealed and lubricated chain with closed shoe 2938 kg (6477 lb)
Track with ALT extended life chain with open shoe 3021 kg (6660 lb)
Cab with heating and cooling system 930 kg (2050 lb)

47998875B 21/05/2018
39
 INTRODUCTION

Consumables
D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

Capacities and specifications

Engine oil
NEW HOLLAND AMBRA MASTERGOLD™ HSP
Oil specification
ENGINE OIL CI-4 SAE 15W-40 API CH–4 / CI–4
Capacity with filter change 16.4 L (17.3 US qt)
Capacity without filter change 15.6 L (16.5 US qt)

Fuel system (Model D150B)

Fuel specification Diesel fuel No. 2
System capacity 300 L (79 US gal)

Cooling system
Additive specification 50% of water + 50% NEW HOLLAND AMBRA AGRIFLU
System capacity 32.50 L (8.59 US gal)
NOTE: This mix has anticorrosive, antiscaling, and antifoaming properties. It does not freeze until -38.0 °C (-36.4 °F).
If the ambient temperature is lower than -37 °C (-34.6 °F), adjust the mixture according to the coolant additive man-
ufacturer's specifications.

Hydraulic system and transmission (D150B Models)

Fluid specification NEW HOLLAND AMBRA AUTO SUPREME 10W-30
Reservoir capacity 98.4 L (26.0 US gal)
Total system capacity 160 L (42 US gal)

Final reducers
NEW HOLLAND AMBRA HYPOIDE 140 GEAR LUBE
Fluid specification
SAE 85W-140
Capacity (each) 14.2 L (15.0 US qt)

Lower rollers (D150B Models)

NEW HOLLAND AMBRA HYPOIDE 90 GEAR LUBE
Oil Specification
SAE 80W-90
Capacity (each) 0.334 L (0.353 US qt)

Tightener wheel (1650L models)

NEW HOLLAND AMBRA HYPOIDE 90 GEAR LUBE
Oil Specification
SAE 80W-90
Capacity (each) 0.225 L (0.238 US qt)

Upper rollers (D150B Models)

NEW HOLLAND AMBRA HYPOIDE 90 GEAR LUBE
Oil Specification
SAE 80W-90
Capacity (each) 0.275 L (0.291 US qt)

Grease Fittings
Grease specification NEW HOLLAND AMBRA GR 75 MD
Quantity As required

ALT tracks (D150B Models)

NEW HOLLAND AMBRA HYPOIDE 90 GEAR LUBE
Oil Specification
SAE 80W-90
Capacity (each pin) 29.00 mL (0.98 US fl oz)

47998875B 21/05/2018
40
 INTRODUCTION

SALT tracks (D150B Models)

NEW HOLLAND AMBRA HYPOIDE 90 GEAR LUBE
Oil Specification
SAE 80W-90
Capacity (each pin) 29.00 mL (0.98 US fl oz)

Cab tilting system

Fluid specification NEW HOLLAND AMBRA AUTO SUPREME 10W-30
Total system capacity 0.36 L (0.38 US qt)

47998875B 21/05/2018
41
 INTRODUCTION

Product identification (Sides of the machine)

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

Left-hand side, right-hand side, front, and rear

NOTE: In this manual, the terms "left-hand side" and "right-hand side" indicate the sides of the machine as seen from
the operator's seat.

AALL15DOZ0001FA 1

(1) Left Hand Side

(2) Right–hand side
(3) Front
(4) Trailing

47998875B 21/05/2018
42
 INTRODUCTION

Part identification - (Identification plates)

D150B XLT, With cab, Tier 3, Power Angle Tilt (PAT) Blade, Made in Brazil LA
[N9AC03000 - ]

Model, serial number, and year of manufacture

When you order parts or obtain information or technical
assistance, tell your dealer the serial number and type of
the machine or implements.

Write the following information in the spaces on the tag:

the type, serial number and year of manufacture of your
machine, implements, and the serial numbers of the dif-
ferent hydraulic and mechanical components.

48091237_B 1

Machine identification
This plate is located on the left-hand side of the machine,
on the side frame of the engine hood.

COIL15DOZ0093AA 2

Motor
This plate is located on the motor valves cover.

RCIL10CWL123AAL 3

47998875B 21/05/2018
43
This as a preview PDF file from best-manuals.com

Download full PDF manual at best-manuals.com