MULTIFUNCTION DISPLAY PAGES SPECIFICATIONS

PARAMETERS Input : 3 phase 4 wire / 1 phase 2 wire

METER Volts : R Y (Phase - Phase)
Page Symbol PARAMETERS Volts : Range 10-500v
V L-L Voltage (L-L) RY, YB, BR Amps : 0.015 to 6.00Amp
YB (Phase - Phase) 1 : 0.2 VA max. per input for Voltage
Burden
BR (Phase - Phase) 2 V L-N Voltage (L-N) RN, YN, BN & Current Signals
A Amps R, Y, B 3 VA max. on Aux. Supply
3 : 90 - 270 VAC / DC
RN (Phase - Neutral)
Aux.Supply
4 Hz Frequency Display : 3 Line x 4 Digit
YN (Phase - Neutral) {0.56 Inches 7 Segment LED Display}
5 W Watts (Active Power) R, Y, B
: True RMS
BN (Phase - Neutral) Computation
6 Var VAr ( Reactive Power) R, Y, B Frequency : 45 Hz - 65 Hz.
0
Ambient : -10 to 55C
Amps : R Phase 7 VA VA ( Apparent Power) R, Y, B
Storage : -20 to 75C 0

Y Phase 8 PF Power Factor R, Y, B Humidity : < 95 % Non-condensing

Weight : 280gms
B Phase 9 Active Energy
Dimensions : 96 X 96 X 55 mm ( L x W x D)
10 Harmonics - Voltage - THDV (V led / flashes ) Panel Cutout : ( 90 +1-0)mm X ( 90 +1-0) mm
FEATURES Power Factor : R Phase Mounting : Flush Mounting with side clamps.
State of Art Microcontroller Based Design 11 Harmonics - Current - THDI ( I led / flashes )
Y Phase
3 Line 4 Digit ultra bright LED display B Phase
12 Load Hour (timer) Measurement range :
Site programmable CT ratio( Primary & Secondary) Volts : 10 - 500VAC L-L
Active Power : R Phase Notes : Amp : 0.015A - 6.00Amp AC
Site programmable PT ratio ( Primary & Secondary) (KW) Y Phase When the V or A Led flashes the reading are of Display update : 1Sec
THDV or THDI when V or A led is steady ON it Hz : 45.0 to 65.0HZ
True RMS measurement B Phase Resolution : 0.1 for Energy , Auto ranging
indicates voltage or current reading.
for other parameters
Password Protection
Apparent Power : R Phase Accuracy : +0.5% of full scale for voltage,
RS 485 Computer Interface current, power,power factor
(KVA) Y Phase
Frquency : +0.1% for Hz
Total Harmonic Distortion B Phase Electrical Wiring / Connection Diagram Energy : class 1.0
Auto Ranging Load
Reactive Power : R Phase

Computer Interface
N B Y R

RS 485 Serial com.

R Amps
Universal Aux. Supply (KVAr) Y Phase S2 A 20
S2
B Phase CT

MECHANICAL DIMENSION 2 S1 B 19
Frequency : System
S1
Bezzel S2

Y Amps
3 S2 G 18
96 mm Active Energy CT

Harmonics - Volts - Total ( THDV phase wise ) 4 S1 S1

Harmonics - Amps - Total ( THDI phase wise )
S2

B Amps
96 mm

Load Hour 5 S2
CT

6 S1 S1

7 R
Sensing VoltS

55 mm
8 Y

90 - 270VAC/DC
Panel Cutout 9 P 12

Aux.sup.
B
91 mm Source
N N 11
!
CAT III

91 mm

MULTIFUNCTION METER -OP-027-V.0 page1 of 2

PROGRAMMING
Menu 3:(To set CT Primary & Secondary) Press ESC Key to come out of
1) Press Prog key to enter Program Mode. when Prog Key is pressed the display shows
2) The Meter Shows Password Entry Page Program MODE.
{Ct P 0001 0001}.
{USR PASS 0000}.
The value can be edited using &
Enter the Password using Key to increment
Keys. After entering desired value press Prog Safety Precautions :
count & Key to move to the next digit. After
key to save value. All safety related codifications, symbols and
entering the password press Prog key, if the instructions that appear in this operating manual or
The first 4 digits are for CT primary
pass word is correct, the unit will enter the on the equipment must be strictly followed to ensure
& next 4 digits are for CT secondary the safety of the operating personnel as well as the
program mode.
instrument.
Default factory set password is 2000 Menu 4: (To clear Energy) If the equipment is not used in a manner
3) Following Programming menus are available when Prog Key is pressed the display shows specified by the manufacturer it might impair the
CLrE. Press Prog key once again, unit reconfirms protection provided by the equipment.
If there is physical damage to the unit then do
Menu Symbol Description by asking " SUrE ? CLrE" By pressing Prog
not use it.
Key once again the energies will get clear or Read complete instruction prior to installation
1 Unit Address for RS485 communication.
press ESC Key to come out. and operation of the unit.
2 To set PT Primary & Secondary Value
3 To set CT Primary & Secondary Value
Menu 5:(To set New Password)
To clear Energy
Wiring Guidelines :
4 when Prog Key is pressed the display shows
1) To Prevent the risk of electric shock power
5 To set New Password "CHG PASS 2000". supply to the equipment must be kept OFF while
To set baud rate & odd / even parity The password can be edited using & doing the wiring arrangement.
6 2) Wiring shall be done strictly according to the
Keys. After entering desired value press Prog
7 To Reset Timer
key to save value.
terminal layout with shortest connection. Confirm
that all connection are correct.
8 To Select Auto / Manual Scroll
Menu 6 : (To set the Baud Rate & Parity)
Select the Menu to be edited using / when Prog Key is pressed the display shows Caution :
Keys and press Prog Key to enter respective "baud". The Baud Rate for RS485 1) To ensure the safe operation of unit , check the
menu. communication can be set using Key.Using wiring and connections.
. key you can select baud / parity menu. The
Menu 1:(Unit Address for RS485 communication) Even / odd / none parity can be set using Key
when Prog Key is pressed the display shows After entering desired value press Progkey to
{Addr 001}. save value. Maximum Baud rate 9600.
The address can be edited using &
Menu 7: (To Reset Load TIMER)
Keys. After entering desired value press Prog
when Prog Key is pressed the display shows
key to save value.
CLrt. Press Prog key once again, unit reconfirms
by asking " ru SurE ? " By pressing Prog
Key once again the load TIMER will get clear or
Menu 2:(To set PT Primary & Secondary)
press ESC Key to come out.
when Prog Key is pressed the display shows
{Pt P 0001 0001}. Menu 8: (To select Auto / Manual Scroll)
The ratio can be edited using & when Prog Key is pressed the display shows
Keys. After entering desired value press Prog ScrL.
key to save value. You can select "dIS" to disable Auto scroll or
The first 4 digits are for PT primary select "EN" to enable Auto scroll using &
& next 4 digits are for PT secondary Keys.After entering desired value pressProg
For eg. If PT ratio is 22KV / 110V you can enter key to save value
value as 0200 0001.

MULTIFUNCTION METER -OP-027-V.0 page2 of 2