0% found this document useful (0 votes)

561 views

Cisco 2600 Router Command Reference

CISCO and ITS SUPPLIERS DISCLAIM All WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE of MERCHANTABILITY, FITNESS FOR a PARTICULAR PURPOSE and NONINFRINGEMENT OR ARISING FROM a COURSE of DEALING, USAGE, OR TRADE PRACTICE. THE SOFTWARE LICENSE and LIMITED WARRANTY FOR the ACCOMPA

Uploaded by

joero

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

561 views

Cisco 2600 Router Command Reference

Uploaded by

joero

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 196

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100

Text Part Number: OL-1957-04

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCBs public domain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. CCIP, the Cisco Powered Network mark, the Cisco Systems Verified logo, Cisco Unity, Fast Step, Follow Me Browsing, FormShare, Internet Quotient, iQ Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, Networking Academy, ScriptShare, SMARTnet, TransPath, and Voice LAN are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All Thats Possible, The Fastest Way to Increase Your Internet Quotient, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, GigaStack, IOS, IP/TV, LightStream, MGX, MICA, the Networkers logo, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, SlideCast, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. All other trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0201R)

CONTENTS
Preface
xi xi xi xii xii xiii

Objectives Audience Organization

Document Conventions Additional Information

Related and Referenced Documents xiii To Access Online User Documentation (PDF and HTML Formats): xiv Access User Documentation on the Documentation CD-ROM (HTML format only): Obtaining Documentation xvi World Wide Web xvi Documentation CD-ROM xvii Ordering Documentation xvii Documentation Feedback xvii Obtaining Technical Assistance xvii Cisco.com xviii Technical Assistance Center xviii Contacting TAC by Using the Cisco TAC Website Contacting TAC by Telephone xviii
CHAPTER

xiv

xviii

Understanding Interface Numbering and Cisco IOS Software Basics 1-1 Understanding Interface Numbering 1-1 Cisco 2600 Series Interface Numbering 1-1 WAN and LAN Interface Numbering 1-2 Voice Interface Numbering in Cisco 2600 Series Routers 1-4 Cisco 3600 Series Interface Numbering 1-4 Cisco 3600 Series Router Slot Numbering 1-4 Cisco 3600 Series Router Unit Numbering 1-8 Cisco 3600 Series Routers Voice Interface Numbering 1-8 Cisco 3700 Series Interface Numbering 1-9 Cisco 3725 Router Slot Numbering 1-9 Cisco 3745 Router Slot Numbering 1-11 Cisco 3700 Series Routers Voice Interface Numbering 1-12
Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

OL-1957-04

iii

Contents

Understanding Cisco IOS Software Basics 1-13 Getting Help 1-13 Understanding Command Modes 1-13 Undoing a Command or Feature 1-14 Saving Configuration Changes 1-15 Upgrading to a New Cisco IOS Release Where to Go Next
CHAPTER

1-15

Using the Setup Command Facility 2-1 Before Starting Your Router 2-1 Using the setup Command Facility Configuring Global Parameters
2-2 2-2

Configuring Interface Parameters 2-5 Ethernet Interface Configuration 2-6 FastEthernet Interface Configuration 2-6 Token Ring Interface Configuration 2-7 Serial Interface Configuration 2-7 Frame Relay Encapsulation 2-8 LAPB Encapsulation 2-8 X.25 Encapsulation 2-8 ATM-DXI Encapsulation 2-9 SMDS Encapsulation 2-9 Serial Cisco IOS Commands Generated 2-9 Asynchronous/Synchronous Serial Interface Configuration 2-9 Synchronous Configuration 2-9 Asynchronous Configuration 2-11 ISDN BRI Interface Configuration 2-12 ISDN BRI Line Configuration 2-15 ISDN BRI Provisioning by Switch Type 2-15 Defining ISDN Service Profile Identifiers 2-17 E1/T1 ISDN PRI Configuration 2-17 E1/T1 PRI Mode 2-17 E1 Channelized Mode 2-18 T1 Channelized Mode 2-20 1-Port, 4-Wire 56-kbps DSU/CSU Configuration Setup 2-22 Choosing Circuit-Switched or Dedicated-Line Service 2-22 Switched Mode 2-22 Dedicated Mode 2-23 Completing the Configuration
2-23

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

OL-1957-04

Contents

Where to Go Next
CHAPTER

2-24

Configuring with the Command-Line Interface Configuring the Host Name and Password 3-2 Verifying the Host Name and Password 3-2 Configuring 1-Port and 2-Port Ethernet Interfaces Configuring Fast Ethernet Interfaces
3-4

3-1

3-3

Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards Configuring 16-Port and 32-Port Asynchronous Network Modules Configuring ISDN BRI WAN Interface Cards 3-10 Configuring ISDN BRI Lines 3-12 ISDN BRI Provisioning by Switch Type 3-12 Defining ISDN Service Profile Identifiers 3-14 Configuring T1 and E1 Interfaces 3-14 Configuring T1 Interfaces 3-15 Configuring E1 Interfaces 3-16 Configuring TDM Connect (Data Pass-Through) Configuring Codec Complexity 3-17 Configuring T1 (FT1) WAN Interface Cards Default Configuration 3-18 Configuring ATM Interfaces 3-20 Configuring PVCs 3-20 Configuring SVCs 3-21 Configuring Inverse Multiplexing for ATM Interfaces Configuring the ATM T1/E1 Interface 3-23 Configuring the IMA Interface 3-24 Checking the IMA Configuration 3-26 Configuring Analog Modem Interfaces 3-26 Checking the Modem Configuration 3-28 Configuring Wireless Multipoint Interfaces Checking the Interface Configuration
3-29 3-28 3-22 3-18 3-9

3-5

3-16

Configuring 1-Port ADSL WAN Interface Card 3-29 Benefits 3-30 Restrictions 3-30 Prerequisites 3-31 Configuration Tasks 3-31 Configuring the ADSL Port on the ADSL WAN Interface Card Verifying ATM Configuration 3-32

3-31

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

Contents

Configuration Examples

3-33

Configuring the NM-AIC-64, Contact Closure Network Module 3-34 Serial Communication Channels 3-35 Serial Data Channel 3-35 Asynchronous Craft Port 3-36 Configuring the AIC 3-36 Configuration Tasks 3-37 Configuring the AIC 3-37 Accessing the AIC 3-40 Configuring the NOC IP Address 3-40 Configuring Alarms 3-41 Programming the Analog Contact Points 3-41 Programming the Discrete Contact Points 3-43 Verifying the IP Address 3-43 Troubleshooting Tips 3-45 Monitoring and Maintaining the NM-AIC-64 Contact Closure Network Module Software Upgrade 3-45 Configuration Backup 3-46 Override 3-46 Configuration Examples 3-46 Configuring the 1-Port HSSI Network Module 3-46 Configuration Tasks 3-47 Specify a HSSI 3-47 Specify HSSI Encapsulation 3-47 Invoke ATM on a HSSI Line 3-47 Convert HSSI to Clock Master 3-48 Disable Fair Queueing 3-48 Configuration Examples 3-48 Configuring the Compression Network Module for the Cisco 3600 Series Routers 3-49 Configuration Task 3-49 Configuration Example 3-50 Configuring the Digital Modem Network Module for the Cisco 3640 Router 3-50 Prerequisites 3-50 Configuration Tasks 3-51 Configure the E1/T1 Network Module for ISDN PRI 3-51 Configure Channelized E1 ISDN PRI 3-51 Configure Channelized T1 ISDN PRI 3-52 Configure the ISDN D-Channel Serial Interfaces 3-53
Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-45

OL-1957-04

Contents

Configure the ISDN D-Channel Serial Interface for E1 Modules Configure the ISDN D-Channel Serial Interface for T1 Modules Configure the Loopback Interface 3-54 Configure the LAN Interface 3-55 Create the Group Asynchronous Interface 3-55 Configure the ISDN Dialer Interface 3-56 Configure the Default IP Pool Information 3-57 Configure Modem Lines for Dial-In and Dial-Out 3-57 Configure the Modem for Dial-In 3-57 Configure the Modem for Dial-Out 3-57 Configuration Example 3-58 Configuring 1-Port G.SHDSL WAN Interface Card 3-58 Restrictions 3-59 Prerequisites 3-59 Configuration Tasks 3-59 Configuring G.SHDSL on a Cisco Router 3-60 Configuring ILMI on the DSLAM Connected to the ADSL WAN Verifying ATM Configuration 3-62 Configuration Examples 3-64 Saving Configuration Changes Where to Go Next
CHAPTER

3-53 3-54

3-62

3-64

Configuring Voice-over-IP 4-1 Voice-over-IP Prerequisites Configuring the Voice Interface

4-1 4-2

Voice-over-IP Configuration Examples 4-3 FXS-to-FXS Connection Using RSVP 4-4 Configuration for Router RLB-1 4-4 Configuration for Router RLB-w 4-5 Configuration for Router R12-e 4-5 Configuration for Router RLB-2 4-5 Linking PBX Users with E&M Trunk Lines 4-6 Router SJ Configuration 4-7 Router SLC Configuration 4-7 PSTN Gateway Access Using FXO Connection 4-8 Router SJ Configuration 4-8 Router SLC Configuration 4-9 PSTN Gateway Access Using FXO Connection (PLAR Mode) Router SJ Configuration 4-9

4-9

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

vii

Contents

Router SLC Configuration 4-10 Configuring Direct-Inward Dialing on a BRI Port Router 1 Configuration 4-11 Router 2 Configuration 4-11 Router 3 Configuration 4-11 Where to Go Next
APPENDIX

4-10

4-11

Configuration Examples

A-1 A-1

Cisco 2600 Series Router Configuration Example Cisco 3631 Router Configuration Example Cisco 3725 Router Configuration Example
A-6 A-10

1-Port ADSL WAN Interface Card Configuration Examples A-12 VoATM over AAL2 on the ATM Interface Configuration Example VoATM over AAL5 on the ATM Interface Configuration Example

A-12 A-14

NM-AIC-64, Contact Closure NetworkConfiguration Examples A-16 AIC IP Address Configuration Example A-16 IP Route to the AIC Configuration Examples A-20 With an Unnumbered IP Address A-20 Without an Unnumbered IP Address A-21 AIC CLI Configuration for Alarms A-22 Discrete Alarm A-22 Analog Alarm Monitoring Current A-22 Analog Alarm Monitoring Current Configured as a Discrete A-22 Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls Configuration in CPE Mode Example A-25 Configuration in CO Mode Example A-27
APPENDIX

A-23

Formatting the Compact Flash Memory Cards

B-1

Formatting Procedures for Compact Flash Memory Cards B-1 Formatting Procedures B-1 Determining the File System on a Compact Flash Memory Card B-1 Formatting Compact Flash Memory as a Class B Flash File System B-3 Formatting Compact Flash Memory as a Class C File System B-4 File and Directory Operations B-4 Operations for Use With Class B Flash File System B-4 Operations for Use with Class C Flash File System B-7 File Operations for Class C Flash File System B-7 Directory Operations for Class C Flash File System B-10

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

viii

OL-1957-04

Contents

B-12

APPENDIX

Using the ROM Monitor

C-1

Entering the ROM Monitor Mode C-1 Configure C-1 Verify C-1 ROM Monitor Commands C-2 ROM Monitor Syntax Conventions C-3 Command Descriptions C-3 Debugging Commands C-5 Configuration Register Commands C-5 Using the show rom-monitor Command C-6 Using the upgrade rom-monitor Command C-7 Procedures for Recovering Boot and System Images Using the xmodem Command C-8 Using the tftpdnld Command C-9
INDEX

C-8

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

Contents

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

OL-1957-04

Preface
This preface discusses the objectives, audience, organization, and conventions of this software configuration guide, and where to get the latest version of this guide.

Objectives
After installing the router, use this guide to complete a basic router configuration using the setup command facility. It also contains information on using the Cisco IOS software to perform other configuration tasks, such as configuring a Voice-over-IP interface and other features. This guide does not provide complete configuration instructions. Refer to the Cisco IOS configuration guides and command references for detailed configuration instructions. These publications are available on the Documentation CD-ROM that came with your router and on Cisco.com. See the Obtaining Documentation section on page xvi for more information.

Audience
This publication is designed for the person who will be responsible for configuring your router. This guide is intended primarily for the following audiences:

Customers with technical networking background and experience System administrators who are familiar with the fundamentals of router-based internetworking, but who might not be familiar with Cisco IOS software System administrators who are responsible for installing and configuring internetworking equipment, and who are familiar with Cisco IOS software

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

Preface Organization

Organization
The major sections of this software configuration guide include: Chapter Chapter 1 Title Understanding Interface Numbering and Cisco IOS Software Basics Using the Setup Command Facility Configuring with the Command-Line Interface Description Provides an overview of the interface numbering conventions for the Cisco routers. Also provides a basic understanding of the Cisco IOS software. Describes how to use the setup command facility to configure your router. Describes how to use the Cisco IOS software command-line interface (CLI) to configure basic router functionality.

Chapter 2 Chapter 3

Chapter 4

Configuring Voice-over-IP Describes how to configure voice network modules with recEive and transMit (E&M), Foreign Exchange Office (FXO), and Foreign Exchange Station (FXS) interfaces for your router. Configuration Examples Provides configuration examples of the Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers.

Appendix A Appendix B

Appendix B, Formatting Provides configuration information for the Cisco Flash the Compact Flash Memory memory. Cards Appendix C, Using the ROM Monitor Describer how the ROM Monitor works in the Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers.

Appendix C

Document Conventions
This publication uses the following conventions to convey instructions and information: Convention boldface font italic font [ ] {x | y | z}
screen font

Description Commands and keywords. Variables for which you supply values. Keywords or arguments that appear within square brackets are optional. A choice of required keywords appears in braces separated by vertical bars. You must select one. Examples of information displayed on the screen. Examples of information you must enter. Nonprinting characters, for example passwords, appear in angle brackets in contexts where italic font is not available. Default responses to system prompts appear in square brackets.

boldface screen font < [ > ]

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

xii

OL-1957-04

Preface Additional Information

Note

This symbol means reader take note. Notes contain helpful suggestions or references to additional information and material.

Timesaver

This symbol means the described action saves time. You can save time by performing the action described in the paragraph.

Caution

This symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Tip

This symbol means the following information will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information, similar to a Timesaver.

Additional Information
This guide does not contain the following:

Network design information Application case studies Troubleshooting information A comprehensive reference to access services

For l information about any of the above topics, refer to the following resources:

Cisco.com Documentation CD-ROM Cisco Technical Assistance Center (TAC)

Preface Related and Referenced Documents

To Access Online User Documentation (PDF and HTML Formats):

From Cisco.com at http://www.cisco.com, under Service & Support, select Technical Documents and select Cisco Product Documentation.

Access User Documentation on the Documentation CD-ROM (HTML format only):

On the Documentation CD-ROM, select Cisco Product Documentation. Paths to specific documents are provided below, starting at Cisco Product Documentation.
Tip

To navigate up to the next higher level in the documentation hierarchy, click on CONTENTS in the navigation bar at the top of each page.

Table 1

Cisco Product Cisco 2600 series routers

Document Title

Cisco 2600 Series Routers Hardware Installation Guide Cisco 2600 Series Modular Routers Quick Access Guide Cisco Network Modules Hardware Installation Guide Cisco WAN Interface Cards Hardware Installation Guide Regulatory Compliance and Safety Information Cisco 3600 Series Routers Hardware Installation Guide Cisco 3620 and Cisco 3640 Modular Access Routers Quick Start Guide Cisco 3660 Modular Access Router Quick Start Guide Cisco Network Modules Hardware Installation Guide Cisco WAN Interface Cards Hardware Installation Guide Cisco RPS Hardware Installation Guide Regulatory Compliance and Safety Information

Cisco 3600 series routers

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

xiv

OL-1957-04

Preface Related and Referenced Documents

Table 1

Cisco Product Cisco 3700 series routers

Document Title

Cisco 3700 Series Routers Hardware Installation Guide Cisco 3725 and Cisco 3745 Modular Access Routers Quick Start Guide Cisco Network Modules Hardware Installation Guide Cisco WAN Interface Cards Hardware Installation Guide Regulatory Compliance and Safety Information Cisco IOS Configuration Fundamentals Configuration Guide Cisco IOS Configuration Fundamentals Command Reference Cisco IOS Dial Technologies Configuration Guide Cisco IOS Wide-Area Networking Configuration Guide Cisco IOS IP Configuration Guide Release 12.2 Cisco IOS Wide-Area Networking Command Reference Debug Command Reference System Error Messages Cisco IOS Software Command Summary Cisco IOS Release notes for your release

Cisco IOS software

Note

Refer to the modular reference publication that corresponds to the Cisco IOS software release installed on your server.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

Preface Obtaining Documentation

Table 1

Cisco Product Other documents

Document Title

Information about TL1 commands can be found in the Telcordia Technology (formerly Bellcore) document Network Maintenance: Network Element and Transport Surveillance Messages, GR-833-CORE, Issue 5, November 1996. For a reference of security-related commands (ACT-USER and CANC-USER) refer to Telcordia Technologys Operations Applications Messages-Network Element and Network System Security Admin Messages, TR-NWT-000835, Issue 2, January 1993. Information about the PRI network module, refer to the 1-Port and 2-Port ISDN-PRI Network Module Configuration Note. For information on how to install an Ethernet module, refer to the 1-Port Ethernet Network Module Configuration Note or the 4-Port Ethernet Network Module Configuration Note. For information on how to correctly install and configure the Digital Network module and the PRI module, refer to the Digital Modem Network Module Configuration Note. To configure the router for voice traffic, refer to the Voice over IP Configuration document To configure DLAMs, refer to the Configuration Guide for DSLAs with NI-2.

Obtaining Documentation
The following sections provide sources for obtaining documentation from Cisco Systems.

World Wide Web

You can access the most current Cisco documentation on the World Wide Web at the following sites:

http://www.cisco.com http://www-china.cisco.com http://www-europe.cisco.com

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

xvi

OL-1957-04

Preface Obtaining Technical Assistance

Documentation CD-ROM
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.

Ordering Documentation
Cisco documentation is available in the following ways:

Registered Cisco Direct Customers can order Cisco Product documentation from the Networking Products MarketPlace: http://www.cisco.com/cgi-bin/order/order_root.pl

Registered Cisco.com users can order the Documentation CD-ROM through the online Subscription Store: http://www.cisco.com/go/subscription

Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco corporate headquarters (California, USA) at 408 526-7208 or, in North America, by calling 800 553-NETS(6387).

Documentation Feedback
If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. You can e-mail your comments to [email protected]. To submit your comments by mail, for your convenience many documents contain a response card behind the front cover. Otherwise, you can mail your comments to the following address: Cisco Systems, Inc. Document Resource Connection 170 West Tasman Drive San Jose, CA 95134-9883 We appreciate your comments.

Obtaining Technical Assistance

Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the TAC website.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

xvii

Preface Obtaining Technical Assistance

Cisco.com
Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco. Cisco.com provides a broad range of features and services to help customers and partners streamline business processes and improve productivity. Through Cisco.com, you can find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online technical support, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available. Customers and partners can self-register on Cisco.com to obtain additional personalized information and services. Registered users can order products, check on the status of an order, access technical support, and view benefits specific to their relationships with Cisco. To access Cisco.com, go to the following website: http://www.cisco.com

Technical Assistance Center

The Cisco TAC website is available to all customers who need technical assistance with a Cisco product or technology that is under warranty or covered by a maintenance contract.

Contacting TAC by Using the Cisco TAC Website

If you have a priority level 3 (P3) or priority level 4 (P4) problem, contact TAC by going to the TAC website: http://www.cisco.com/tac P3 and P4 level problems are defined as follows:

P3Your network performance is degraded. Network functionality is noticeably impaired, but most business operations continue. P4You need information or assistance on Cisco product capabilities, product installation, or basic product configuration.

In each of the above cases, use the Cisco TAC website to quickly find answers to your questions. To register for Cisco.com, go to the following website: http://www.cisco.com/register/ If you cannot resolve your technical issue by using the TAC online resources, Cisco.com registered users can open a case online by using the TAC Case Open tool at the following website: http://www.cisco.com/tac/caseopen

Contacting TAC by Telephone

If you have a priority level 1(P1) or priority level 2 (P2) problem, contact TAC by telephone and immediately open a case. To obtain a directory of toll-free numbers for your country, go to the following website: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

xviii

OL-1957-04

Preface Obtaining Technical Assistance

P1 and P2 level problems are defined as follows:

P1Your production network is down, causing a critical impact to business operations if service is not restored quickly. No workaround is available. P2Your production network is severely degraded, affecting significant aspects of your business operations. No workaround is available.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

xix

Preface Obtaining Technical Assistance

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

OL-1957-04

C H A P T E R

Understanding Interface Numbering and Cisco IOS Software Basics

This chapter provides an overview of the interface numbering in the Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers. It also describes how to use the Cisco IOS software commands.

Understanding Interface Numbering

This section contains information with which you should be familiar before you begin to configure your router for the first time, including interface numbering and what you should do before starting your router.

Cisco 2600 Series Interface Numbering

Each network interface on a Cisco 2600 series router is identified by a slot number and a unit number. Table 1-1 lists the router models and summarizes the interfaces supported on each model that are available in the Cisco 2600 series routers

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

1-1

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

Table 1-1

Router Models

Model Cisco 2610 Cisco 2610XM Cisco 2611 Cisco 2611XM Cisco 2612 Cisco 2613 Cisco 2620 Cisco 2620XM Cisco 2621 Cisco 2621XM Cisco 2650 Cisco 2650XM Cisco 2651 Cisco 2651XM Cisco 2691

Ethernet (10BASE-T) 1

Token-Ring (RJ-45)

Fast Ethernet Network (10/100) Module Slot 1 1 1 1 2 1 1 1 1 1 2 2 1 1 2 2 2 1 1 1 1 1 1 1 1 1

WAN Interface Card Slots 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3

Advanced Integration Module Slots 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2

1 1

Note

The number and type of interfaces vary depending on the router.

WAN and LAN Interface Numbering

The Cisco 2600 series router chassis contains the following wide-area network (WAN) and local-area network (LAN) interface types:

Built-in LAN interfaces: Ethernet, FastEthernet, Token Ring Two or three slots in which you can install WAN interface cards (WICs) One slot in which you can install a network module

The numbering format is Interface-type Slot-number/Interface-number. Two examples are:

Ethernet 0/0 Serial 1/2

The slot number is 0 for all built-in interfaces and 0 for all WIC interfaces; the slot number is 1 for network module interfaces.

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

1-2

OL-1957-04

Chapter 1

Understanding Interface Numbering and Cisco IOS Software Basics Understanding Interface Numbering

Interface (port) numbers begin at 0 for each interface type, and continue from right to left and (if necessary) from bottom to top. Figure 1-1 below shows a router of 1 RU height with:

A WIC in each WIC slot (containing interface Serial 0/0 in physical slot W0, and interface Serial 0/1 in physical slot W1) A 4-serial-port network module in slot 1 (containing the following ports: Serial 1/0, Serial 1/1, Serial 1/2, and Serial 1/3) First built-in Ethernet interfaceEthernet 0/0 Second built-in Ethernet interfaceEthernet 0/1, or optionally in Cisco 2612 and Cisco 2613 only: Token Ring interface 0/0
Example of 1RU Router

Figure 1-1

Figure 1-2 below shows a router of 2 RU height with:

A WIC in each WIC slot (containing interfaces Serial 0/0 and Serial 0/1 in physical slot W0, interface Serial 0/2 in physical slot W1, and interface BRI 0/0 in physical slot W2) A 2-port T1 network module in slot 1 (containing the following ports: T1 1/0 and T1 1/1) Two built-in Ethernet 10/100 interfacesFastEthernet 0/0 and FastEthernet 0/1
Example of a 2RU Router

Figure 1-2

Note

The slot number for all WIC interfaces is always 0. (The W0 and W1 slot designations are for physical slot identification only.) Interfaces in the WICs are numbered from right to left, starting with 0/0 for each interface type, regardless of which physical slot the WICs are installed in. Some examples are:

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

1-3

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

If physical slot W0 is empty and physical slot W1 contains a 1-port serial WIC, the interface

number in the WIC is numbered Serial 0/0.

If slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port serial WIC, the interfaces

in physical slot W0 are numbered Serial 0/0 and Serial 0/1, and the interface in physical slot W1 is numbered Serial 0/2.
If slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port BRI WIC, the interfaces

in physical slot W0 are numbered Serial 0/0 and Serial 0/1, and the interface in physical slot W1 is numbered BRI 0/0.

Voice Interface Numbering in Cisco 2600 Series Routers

Voice interfaces are numbered differently from the WAN interfaces described in the previous section. Voice interfaces are numbered as follows: chassis slot/voice module slot/voice interface If a 4-channel voice network module is installed in chassis slot 1, the voice interfaces are:

1/0/0Chassis slot 1/Voice module slot 0/Voice interface 0 1/0/1Chassis slot 1/Voice module slot 0/Voice interface 1 1/1/0Chassis slot 1/Voice module slot 1/Voice interface 0 1/1/1Chassis slot 1/Voice module slot 1/Voice interface 1

Cisco 3600 Series Interface Numbering

Each individual network interface on a Cisco 3600 series router is identified by a slot number and a unit number.

Cisco 3600 Series Router Slot Numbering

A Cisco 3600 series router chassis includes up to six slots in which you can install modules. The Cisco 3600 series includes the Cisco 3660 (see Figure 1-3), Cisco 3640 (see Figure 1-4) and Cisco 3620 routers (see Figure 1-5). The Cisco 3660 has six network module slots, the Cisco 3640 has four slots, the Cisco 3620 has two slots, and the Cisco 3631 (see Figure 1-6) has four slots. You can install any module into any available slot in the chassis.

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

1-4

OL-1957-04

Chapter 1

Understanding Interface Numbering and Cisco IOS Software Basics Understanding Interface Numbering

Figure 1-3

Cisco 3660 Router Rear View

Figure 1-4

Cisco 3640 Router Rear View

Figure 1-5

Cisco 3620 Router Rear View

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

1-5

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

Figure 1-6

Cisco 3631 Router Rear View

For the Cisco 3660 router (see Figure 1-3), the slots are numbered as follows:

Slot 0 contains fixed FastEthernet ports and is located at the top of the chassis. Slot 1 is at the bottom right (as viewed from the rear of the chassis), near the power supply. Slot 2 is at the bottom left. Slot 3 is at the right, above slot 1. Slot 4 is at the left, above slot 2 Slot 5 is at the right, above slot 3. Slot 6 is at the left, above slot 4.

For the Cisco 3620 and Cisco 3640 routers shown in Figure 1-4 and Figure 1-5, the slots are numbered as follows:

Slot 0 is at the bottom right (as viewed from the rear of the chassis), near the power supply. Slot 1 is at the bottom left. Slot 2 is at the top right, above slot 0. Slot 3 is at the top left, above slot 1.

For the Cisco 3631 router shown in Figure 1-6, the slots are numbered as follows:

Slot 0 for all built-in interfaces like the FastEthernet port at the bottom center near the Console/AUX ports Slot 0 for all WAN interface card (WIC) interfaces Slot 1 for network module interfaces at the bottom left. Slot 2 for network module interfaces at the top left, above slot 1.

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

1-6

OL-1957-04

Chapter 1

Understanding Interface Numbering and Cisco IOS Software Basics Understanding Interface Numbering

Figure 1-7

Example of the Cisco 3631 Router Interface Numbering

Figure 1-7 shows an example of the interface numbering where the following interfaces are installed:

A WIC in each WIC slot (containing interfaces serial 0/0 and serial 0/1 in physical slot W0, and interface serial 0/2 in physical slot W1) A 32-port asynchronous network module in slot 1 (containing interfaces serial 1/0 through serial 1/31) An alarm interface controller network module in slot 2 (internally connected to interface serial 2/0) One built-in Ethernet 10/100 interfaceFastEthernet 0/0

Note

The logical slot number for all WIC interfaces is always 0. (The W0 and W1 slot designations are for physical slot identification only.) Interfaces in the WICs are numbered from right to left, starting with 0/0 for each interface type, regardless of which physical slot the WICs are installed in. Some examples are:
If physical slot W0 is empty and physical slot W1 contains a 1-port serial WIC, then the logical

interface in the WIC is numbered serial 0/0.

If physical slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port serial WIC, then

the logical interfaces in physical slot W0 are numbered serial 0/0 and serial 0/1 and the logical interface in physical slot W1 is numbered Serial 0/2.
If physical slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port BRI WIC, then

the logical interfaces in physical slot W0 are numbered serial 0/0 and serial 0/1, and the logical interface in physical slot W1 is numbered BRI 0/0. Some modules have two small slots, labeled W0 and W1, for WAN interface cards. For example, Figure 1-8 shows the W0 and W1 slots of the 2 Ethernet 2 WAN card slot (2E 2-slot) module. You can install WAN interface cards into the small module slots (W0 and W1). Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) WAN interface cards are keyed so that you can install them into slot W1 only. Serial WAN interface cards can be installed into either slot, W0 or W1.

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

1-7

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

Figure 1-8

WAN Interface Card Slots

Cisco 3600 Series Router Unit Numbering

Cisco 3600 series routers unit numbers identify the interfaces on the modules and WAN interface cards installed in the router. Unit numbers begin at 0 for each interface type, and continue from right to left and (if necessary) from bottom to top. Modules and WAN interface cards are identified by interface type, slot number, followed by a forward slash (/), and then the unit number; for example, Ethernet 0/0.
Note

In the Cisco 3660 router, the fixed FastEthernet ports are located in chassis slot 0, and are identified by: interface type chassis slot/ unit number For example: FastEthernet 0/0 Figure 1-9 shows a router with a 2E 2-slot module in slots 0 and 1. Two serial WAN interface cards are installed in the module in slot 0. One serial and one ISDN BRI WAN interface card are installed in the module in slot 1. As shown in Figure 1-9, the unit numbers are as follows:

Slot 0, Ethernet interface 0, referred to as Ethernet 0/0 Slot 0, Ethernet interface 1, referred to as Ethernet 0/1 Slot 0, serial interface 0, referred to as serial 0/0 Slot 0, serial interface 1, referred to as serial 0/1 Slot 1, Ethernet interface 0, referred to as Ethernet 1/0 Slot 1, Ethernet interface 1, referred to as Ethernet 1/1 Slot 1, serial interface 0, referred to as serial 1/0 Slot 1, BRI interface 0, referred to as BRI 1/0

Note

The 2E 2-slot module described in this example provides both an attachment unit interface (AUI) and 10BASE-T port. Only one of these ports can be used at a time. The module automatically detects which port, AUI or 10BASE-T, is in use.

Cisco 3600 Series Routers Voice Interface Numbering

Voice interfaces are numbered differently from WAN interfaces described in the previous section, Cisco 3600 Series Router Unit Numbering. Voice interfaces are numbered as follows: interface type chassis slot/voice module slot/voice interface

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

1-8

OL-1957-04

Chapter 1

Understanding Interface Numbering and Cisco IOS Software Basics Understanding Interface Numbering

If you have a 4-channel voice network module installed in slot 1 of your router, the voice interfaces will be:

Slot 1, voice network module slot 0, voice interface 0, referred to as voice 1/0/0 (closest to chassis slot 0) Slot 1, voice network module slot 0, voice interface 1, referred to as voice 1/0/1 Slot 1, voice network module slot 1, voice interface 0, referred to as voice 1/1/0 Slot 1, voice network module slot 1, voice interface 1, referred to as voice 1/1/1 (farthest from chassis slot 0)
Cisco 3600 Series Unit Numbers

Figure 1-9

Cisco 3700 Series Interface Numbering

Each WAN and LAN interface on a Cisco 3700 series router is identified by a slot number and a unit number. The Cisco 3700 series includes the Cisco 3725 and Cisco 3745.

Cisco 3725 Router Interface Numbering

The Cisco 3725 router chassis contains the following wide-area network (WAN) and local area network (LAN) interface types:

Two built-in FastEthernet LAN interfaces Three slots in which you can install WAN interface cards (WICs) One single-width slot (slot 1) in which you can install one network module One double-width slot (slot 2) in which you can install one single-width or double-width network module

Cisco 3725 Router Slot Numbering

The numbering format is Interface-type Slot-number/Interface-number. Two examples are:
FastEthernet 0/0 Serial 1/2.

The slot numbers are as follows:

0 for all built-in interfaces 0 for all WIC interfaces

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

1-9

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

1 for interfaces in the single-width network module slot 2 for interfaces in the double-width network module slot

Interface (port) numbers begin at 0 for each interface type, and continue from right to left and (if necessary) from bottom to top. Figure 1-10 below shows an example of interface numbering on a Cisco 3725 router with:

A WIC in each WIC slot (containing interfaces Serial 0/0 and Serial 0/1 in physical slot W0, interface Serial 0/2 in physical slot W1, and interface BRI 0/0 in physical slot W2) A 2-port T1 network module in slot 1 (containing the following ports: T1 1/0 and T1 1/1) A 36-port Etherswitch network module in slot 2 (containing the following ports: FastEthernet 2/0 through 2/35, and GigabitEthernet 2/0 and 2/1) Two built-in Ethernet 10/100 interfacesFastEthernet 0/0 and FastEthernet 0/1

Figure 1-10 Cisco 3725 Router Rear View

Note

the WIC is numbered Serial 0/0.

If slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port serial WIC, the interfaces

in physical slot W0 are numbered Serial 0/0 and Serial 0/1, and the interface in physical slot W1 is numbered BRI 0/0.

Cisco 3745 Router Interface Numbering

The Cisco 3745 router chassis contains the following wide-area network (WAN) and local-area network (LAN) interface types:

2 built-in FastEthernet LAN interfaces

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

1-10

OL-1957-04

Chapter 1

Understanding Interface Numbering and Cisco IOS Software Basics Understanding Interface Numbering

3 slots in which you can install WAN or voice interface cards 4 network module slots.

Cisco 3745 Router Slot Numbering

The numbering format in the Cisco 3745 router is Interface type Slot number/Interface number. Two examples are:
FastEthernet 0/0 Serial 1/2.

The slot numbers are as follows:

0 for all built-in interfaces 0 for all WIC interfaces 1 for the lower right network module slot 2 for the lower left network module slot 3 for the upper right network module slot 4 for the upper left network module slot

If double-wide network modules are installed, the slot numbers are as follows:

2 for the lower double-wide slot 4 for the upper double-wide slot

Interface (port) numbers begin at 0 for each interface type, and continue from right to left and (if necessary) from bottom to top. Figure 1-11 shows the rear panel of the Cisco 3745 with:

A WIC in each of the three WAN interface card slots A single-width network module in each of the four network module slots Two AC power supplies

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

1-11

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

Figure 1-11 Cisco 3745 Rear Panel

1 2 3 4 5

Interface card slots Network modules Power supply Fast Ethernet 0/0 port Fast Ethernet 0/1 port

6 7 8 9

Cisco 3700 compact Flash slot Auxiliary port Console port Power supply

10 Network modules

Note

The slot number for all WIC interfaces is always 0. (The W0, W1, and W2 slot designations are for physical slot identification only.) Interfaces in the WICs are numbered from right to left, starting with 0/0 for each interface type, regardless of which physical slot the WICs are installed in. Some examples are:
If physical slot W0 is empty and physical slot W1 contains a 1-port serial WIC, the interface in

the WIC is numbered Serial 0/0.

If slot W0 contains a 2-port serial WIC and slot W1 contains a 1-port serial WIC, the interfaces

in physical slot W0 are numbered Serial 0/0 and Serial 0/1, and the interface in physical slot W1 is numbered BRI 0/0.

Cisco 3700 Series Routers Voice Interface Numbering

Voice interfaces in Cisco 3725 and Cisco 3745 routers are numbered differently from the WAN interfaces described in the previous section Voice interfaces are numbered as follows:
chassis slot/voice module slot/voice interface

If a 4-channel voice network module is installed in chassis slot 1, the voice interfaces are:

1/0/0Chassis slot 1/Voice module slot 0/Voice interface 0

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

1-12

OL-1957-04

Chapter 1

Understanding Interface Numbering and Cisco IOS Software Basics Understanding Cisco IOS Software Basics

1/0/1Chassis slot 1/Voice module slot 0/Voice interface 1 1/1/0Chassis slot 1/Voice module slot 1/Voice interface 0 1/1/1Chassis slot 1/Voice module slot 1/Voice interface 1

Understanding Cisco IOS Software Basics

This section describes what you need to know about the Cisco IOS software before you configure the router using the command-line interface (CLI). This chapter includes the following:

Getting Help, page 1-13 Understanding Command Modes, page 1-13 Undoing a Command or Feature, page 1-14 Saving Configuration Changes, page 1-15 Where to Go Next, page 1-15

Understanding these concepts will save time as you begin to use the CLI. If you have never used the Cisco IOS software or need a refresher, take a few minutes to read this chapter before you proceed to the next chapter. If you are already familiar with Cisco IOS software, proceed to Chapter 2, Using the Setup Command Facility.

Getting Help
Use the question mark (?) and arrow keys to help you enter commands:

For a list of available commands, enter a question mark:

Router> ?

To complete a command, enter a few known characters followed by a question mark (with no space):
Router> s?

For a list of command variables, enter the command followed by a space and a question mark:
Router> show ?

To redisplay a command you previously entered, press the up arrow key. You can continue to press the up arrow key for more commands.

Understanding Command Modes

The Cisco IOS user interface is divided into different modes. Each command mode permits you to configure different components on your router. The commands available at any given time depend on which mode you are currently in. Entering a question mark (?) at the prompt displays a list of commands available for each command mode. Table 1-2 lists the most common command modes.

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

1-13

Chapter 1 Understanding Cisco IOS Software Basics

Understanding Interface Numbering and Cisco IOS Software Basics

Table 1-2

Common Command Modes

Command Mode User EXEC Privileged EXEC

Access Method Log in. From user EXEC mode, enter the enable command. From the privileged EXEC mode, enter the configure terminal command. From the global configuration mode, enter the interface type number command, such as interface serial 0/0.

Router Prompt Displayed

Router>

Exit Method Use the logout command. To exit to user EXEC mode, use the disable, exit, or logout command. To exit to privileged EXEC mode, use the exit or end command, or press Ctrl-z. To exit to global configuration mode, use the exit command. To exit directly to privileged EXEC mode, press Ctrl-z.

Router#

Global configuration

Router (config)#

Interface configuration

Router (config-if)#

Timesaver

Each command mode restricts you to a subset of commands. If you are having trouble entering a command, check the prompt, and enter the question mark (?) for a list of available commands. You might be in the wrong command mode or using the wrong syntax. In the following example, notice how the prompt changes after each command to indicate a new command mode:
Router> enable Password: <enable password> Router# configure terminal Router(config)# interface serial 0/0 Router(config-if)# line 0 Router(config-line)# controller t1 0 Router(config-controller)# exit Router(config)# exit Router# %SYS-5-CONFIG_I: Configured from console by console

The last message is normal and does not indicate an error. Press Return to get the Router# prompt.
Note

You can press Ctrl-z in any mode to immediately return to enable mode ( Router#), instead of entering exit, which returns you to the previous mode.

Undoing a Command or Feature

If you want to undo a command you entered or disable a feature, enter the keyword no before most commands; for example, no ip routing.

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

1-14

OL-1957-04

Chapter 1

Understanding Interface Numbering and Cisco IOS Software Basics Upgrading to a New Cisco IOS Release

Saving Configuration Changes

You need to enter the copy running-config startup-config command to save your configuration changes to nonvolatile random-access memory (NVRAM), so the changes are not lost if there is a system reload or power outage. For example:
Router# copy running-config startup-config Building configuration...

It might take a minute or two to save the configuration to NVRAM. After the configuration has been saved, the following appears:
[OK] Router#

Upgrading to a New Cisco IOS Release

To install or upgrade to a new Cisco IOS release, refer to Appendix B, Formatting the Compact Flash Memory Cards.

Where to Go Next
Now that you have learned some Cisco IOS software basics, you can begin to configure the router using the CLI. Remember that:

You can use the question mark (?) and arrow keys to help you enter commands. Each command mode restricts you to a set of commands. If you have difficulty entering a command, check the prompt and then enter the question mark (?) for a list of available commands. You might be in the wrong command mode or using the wrong syntax. To disable a feature, enter the keyword no before the command; for example, no ip routing. You need to save your configuration changes to NVRAM so the changes are not lost if there is a system reload or power outage.

Proceed to Chapter 2, Using the Setup Command Facility, to begin configuring the router.

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

1-15

Chapter 1 Where to Go Next

Understanding Interface Numbering and Cisco IOS Software Basics

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

1-16

OL-1957-04

C H A P T E R

Using the Setup Command Facility

This chapter describes how to use the setup command facility to configure your router. The setup command facility prompts you to enter information needed to start a router functioning quickly. The facility steps you through a basic configuration, including local-area network (LAN) and wide-area network (WAN) interfaces. The following sections are included:

Before Starting Your Router, page 2-1 Using the setup Command Facility, page 2-2 Configuring Global Parameters, page 2-2 Configuring Interface Parameters, page 2-5 Completing the Configuration, page 2-23 Where to Go Next, page 2-24

If you prefer to configure the router manually or you wish to configure a module or interface that is not included in the setup command facility, proceed to Chapter 3, Configuring with the Command-Line Interface, for step-by-step instructions.

Before Starting Your Router

Before you power on your router and begin to use the setup command facility, make sure you follow these steps:
Step 1 Step 2 Step 3 Step 4

Set up the hardware as described in the documentation appropriate to your router. Configure your PC terminal emulation program for 9600 baud, 8 data bits, no parity, and 1 stop bit. Determine which network protocols you are supporting (for example, AppleTalk, IP, Novell IPX, and so on). Determine the following for each network protocol:

Addressing plan Which WAN protocols you will run on each interface (for example, Frame Relay, HDLC, X.25, and so on)

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-1

Chapter 2 Using the setup Command Facility

Using the Setup Command Facility

Using the setup Command Facility

The setup command facility displays from your PC terminal emulation program window. To create a basic configuration for your router, do the following:

Complete the steps in the Configuring Global Parameters section on page 2-2. Complete the steps in the Configuring Interface Parameters section on page 2-5 that apply to your router and network. Complete the steps in the Completing the Configuration section on page 2-23.

Note

If you make a mistake while using the setup command facility, you can exit and run the facility again. Press Ctrl-c, and type setup at the enable mode prompt ( 2600#).

Configuring Global Parameters

Step 1

Power on the router. The power switch is on the rear panel of the router, at the lower right corner, near the power cord. Messages will begin to appear in your terminal emulation program window.

Caution

Do not press any keys on the keyboard until the messages stop. Any keys pressed during this time are interpreted as the first command typed when the messages stop, which might cause the router to power off and start over. It takes a few minutes for the messages to stop. The messages look similar to the following:
Note

The messages vary, depending on the Cisco IOS software release, interface modules in place in your router, and feature set you select. The screen displays in this section are for reference only and might not exactly reflect the messages on your console.

System Bootstrap, Version 11.3(1)XA, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1) Copyright (c) 1998 by cisco Systems, Inc. C2600 platform with 32768 Kbytes of main memory rommon 1 b f program load complete, entry point: 0x80008000, size: 0xef4e0 Self decompressing the image : ############################################### [OK] Notice: NVRAM invalid, possibly due to write erase. program load complete, entry point: 0x80008000, size: 0x415b20 Self decompressing the image : ########################################################################################## ########################################################################################## ########################################################################################## ###############[OK]

Restricted Rights Legend

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-2

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Global Parameters

Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706

Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-JS-M), Version 11.3(2)XA, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1) Copyright (c) 1986-1998 by cisco Systems, Inc. Compiled Tue 10-Mar-98 14:18 by rnapier Image text-base: 0x80008084, data-base: 0x809CD49C cisco 2611 (MPC860) processor (revision 0x100) with 24576K/8192K bytes of memory. Processor board ID 04614954 M860 processor, part number 0 mask 32 Bridging software. X.25 software, Version 3.0.0. 2 Ethernet/IEEE 802.3 interface(s) 3 Serial network interface(s) 32 terminal line(s) DRAM configuration parity is disabled. 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write) --- System Configuration Dialog --At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'.

Step 2

When the following message appears, enter yes to begin the initial configuration dialog:
Would you like to enter the initial configuration dialog? [yes/no]:

Note

If you answer no to this message, you are prompted to terminate AutoInstall. AutoInstall is a procedure that configures a new router based on the configuration of an existing router. If you terminate AutoInstall, you enter the Cisco IOS software CLI.

Note

The interface numbering that appears in the next step is dependent on the type of Cisco modular router platform. This example shows a Cisco 2600 series router.

Step 3

When the following message appears, press Return to see the current interface summary:
First, would you like to see the current interface summary? [yes]: Any interface listed with OK? value NO does not have a valid configuration Interface Ethernet0/0 Serial0/0 BRI0/0 IP-Address unassigned unassigned unassigned OK? NO NO NO Method unset unset unset Status up up up Protocol up down up

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-3

Chapter 2 Configuring Global Parameters

Using the Setup Command Facility

Serial0/1 Serial0/2

unassigned unassigned

NO NO

unset unset

up up

down down

Step 4

Enter a host name for the router (this example uses 2600):
Configuring global parameters: Enter host name [Router]: 2600 The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration.

Step 5

Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration:
Enter enable secret: xxxx The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images.

Step 6

Enter an enable password that is different from the enable secret password. This password is not encrypted (less secure) and can be seen when viewing the configuration:
Enter enable password: guessme The virtual terminal password is used to protect access to the router over a network interface.

Step 7

Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port:
Enter virtual terminal password: guessagain

Step 8

Respond to the following prompts as appropriate for your network:

Configure SNMP Network Management? [yes]: Community string [public]: Configure LAT? [no]: Configure AppleTalk? [no]: Configure DECnet? [no]: Configure IP? [yes]: Configure IGRP routing? [yes]: Your IGRP autonomous system number [1]: 15

Note

If you answer no to IGRP, you are prompted to configure RIP.

CLNS? [no]: IPX? [no]: Vines? [no]: XNS? [no]: Apollo? [no]: bridging? [no]:

Configure Configure Configure Configure Configure Configure

Step 9

Configure the ISDN switch type used by the Basic Rate Interface (BRI) module:
BRI interface needs isdn switch-type to be configured Valid switch types are : [0] none..........Only if you don't want to configure BRI. [1] basic-1tr6....1TR6 switch type for Germany [2] basic-5ess....AT&T 5ESS switch type for the US/Canada [3] basic-dms100..Northern DMS-100 switch type for US/Canada [4] basic-net3....NET3 switch type for UK and Europe [5] basic-ni......National ISDN switch type

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-4

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Interface Parameters

[6] basic-ts013...TS013 switch type for Australia [7] ntt...........NTT switch type for Japan [8] vn3...........VN3 and VN4 switch types for France Choose ISDN BRI Switch Type [2]:

Step 10

Configure the asynchronous serial lines for the integrated modems on the modules installed in the router. (If you want to allow users to dial in through the integrated modems, you must configure the asynchronous lines.)
Async lines accept incoming modems calls. If you will have users dialing in via modems, configure these lines. Configure Async lines? [yes]: Async line speed [115200]:

Note

Cisco recommends that you do not change this speed.

Will you be using the modems for inbound dialing? [yes]:

Note

If your asynchronous interfaces will be using the same basic configuration parameters, Cisco recommends answering yes to the next prompt. That way, you group the modems so that they can be configured as a group. Otherwise, you will need to configure each interface separately.

Would you like to put all async interfaces in a group and configure them all at one time? [yes]: Allow dial-in users to choose a static IP addresses? [no]: Configure for TCP header compression? [yes]: Configure for routing updates on async links? [no]: Enter the starting address of IP local pool? [X.X.X.X]: 172.20.30.40

Note

Make sure the starting and ending addresses of the IP pool are in the same subnet.
Enter the ending address of IP local pool? [X.X.X.X]: 172.20.30.88

You can configure a test user to verify that your dial-up service is working properly What is the username of the test user? [user]: What is the password of the test user? [passwd]: Will you be using the modems for outbound dialing? [no]: Configuring interface parameters:

Configuring Interface Parameters

From this point on in the setup process, the prompts you see vary depending on the network modules and WAN interface cards in place in your router. The following sections provide examples of the setup steps for each interface module. Refer to the sections appropriate to your router. Configuration for network modules includes:

Ethernet Interface Configuration, page 2-6 FastEthernet Interface Configuration, page 2-6 Token Ring Interface Configuration, page 2-7
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

OL-1957-04

2-5

Chapter 2 Configuring Interface Parameters

Using the Setup Command Facility

Serial Interface Configuration, page 2-7 Asynchronous/Synchronous Serial Interface Configuration, page 2-9 ISDN BRI Interface Configuration, page 2-12 E1/T1 ISDN PRI Configuration, page 2-17
E1/T1 PRI Mode, page 2-17 E1 Channelized Mode, page 2-18 T1 Channelized Mode, page 2-20

1-Port, 4-Wire 56-kbps DSU/CSU Configuration Setup, page 2-22

When you complete the setup steps for your interface modules, go to the Completing the Configuration section on page 2-23 for directions on saving your configuration.

Ethernet Interface Configuration

This section contains a sample configuration for the Ethernet interface. Enter the values appropriate for your router and network. The messages you see may vary.
Do you want to configure Ethernet0/0 interface [yes]: Configure IP on this interface? [yes]: IP address for this interface: 255.255.255.0 Subnet mask for this interface [255.0.0.0]: Class A network is 1.0.0.0, 8 subnet bits, mask is /8 Configure IPX on this interface? [no]: y IPX network number [1]: Need to select encapsulation type [0] sap (IEEE 802.2) [1] snap (IEEE 802.2 SNAP) [2] arpa (Ethernet_II) [3] novell-ether (Novell Ethernet_802.3) Enter the encapsulation type [2]:

FastEthernet Interface Configuration

This section contains a sample configuration for the FastEthernet interface. Enter the values appropriate for your router and network. The messages you see may vary.
Do you want to configure FastEthernet0/0 interface [yes]: Use the 100 Base-TX (RJ-45) connector? [yes]: Operate in full-duplex mode? [no]: Configure IP on this interface? [no]: yes IP address for this interface: 6.0.0.1 Number of bits in subnet field [0]: Class A network is 6.0.0.0, 0 subnet bits, mask is /8 Configure IPX on this interface? [yes]: IPX network number [1]: Need to select encapsulation type [0] sap (IEEE 802.2) [1] snap (IEEE 802.2 SNAP) [2] arpa (Ethernet_II) [3] novell-ether (Novell Ethernet_802.3) Enter the encapsulation type [2]:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-6

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Interface Parameters

Token Ring Interface Configuration

This section contains a sample configuration for the Token Ring interface. Enter the values appropriate for your router and network. The messages you see may vary.
Do you want to configure TokenRing0/0 interface? [yes]: Tokenring ring speed (4 or 16)? [16]: Configure IP on this interface? [yes]: IP address for this interface: 1.0.0.1 Subnet mask for this interface [255.0.0.0]: Class A network is 1.0.0.0, 8 subnet bits; mask is /8 Configure IPX on this interface? [no]: y IPX network number [1]: Need to select encapsulation type [0] sap (IEEE 802.2) [1] snap (IEEE 802.2 SNAP) Enter the encapsulation type [0]:

Serial Interface Configuration

This section contains a sample configuration for the 1- or 2-port serial interface. Enter the values appropriate for your router and network. The messages you see may vary.
Do you want to configure Serial0/0 interface? [yes]: Some encapsulations supported are ppp/hdlc/frame-relay/lapb/atm-dxi/smds/x25 Choose encapsulation type [ppp]:

Note

The following sections describe the prompts for each encapsulation type. For PPP and HDLC encapsulation, no further configuration is needed.
No serial cable seen. Choose mode from (dce/dte) [dte]:

Note

If no cable is plugged in to your router, you need to indicate whether the interface is to be used as DTE or DCE. If a cable is present, the setup command facility determines the DTE/DCE status. If the serial cable is DCE, you see the following prompt:
Serial interface needs clock rate to be set in dce mode. The following clock rates are supported on the serial interface. 0 1200, 2400, 4800, 9600, 19200, 38400 56000, 64000, 72000, 125000, 148000, 500000 800000, 1000000, 1300000, 2000000, 4000000, 8000000 Choose clock rate from above: [2000000]: Configure IP on this interface? [yes]: IP address for this interface: 2.0.0.1 Subnet mask for this interface [255.0.0.0]: Class A network is 2.0.0.0, 8 subnet bits; mask is /8 Configure IPX on this interface? [no]: yes IPX network number [8]:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-7

Chapter 2 Configuring Interface Parameters

Using the Setup Command Facility

Frame Relay Encapsulation

The following lmi-types are available to be set, when connected to a frame relay switch [0] none [1] ansi [2] cisco [3] q933a Enter lmi-type [2]:

Note

The setup command facility only prompts for the data-link connection identifier (DLCI) number if you specify none for the Local Management Interface (LMI) type. If you accept the default or specify another LMI type, the DLCI number is provided by the specified protocol.
Enter the DLCI number for this interface [16]: Do you want to map a remote machines IP address to dlci? [yes]: IP address for the remote interface: 2.0.0.2 Do you want to map a remote machines IPX address to dlci? [yes]: IPX address for the remote interface: 40.1234.5678 Serial interface needs clock rate to be set in dce mode. The following clock rates are supported on the serial interface. 0 1200, 2400, 4800, 9600, 19200, 38400 56000, 64000, 72000, 125000, 148000, 500000 800000, 1000000, 1300000, 2000000, 4000000, 8000000 choose speed from above: [2000000]: 1200 Configure IP on this interface? [yes]: IP address for this interface: 2.0.0.1 Subnet mask for this interface [255.0.0.0]: Class A network is 2.0.0.0, 8 subnet bits; mask is /8

If IPX is configured on the router, the setup command facility prompts for the IPX map:
Do you want to map a remote machine's IPX address to dlci? [yes]: IPX address for the remote interface: 40.0060.34c6.90ed

LAPB Encapsulation
lapb circuit can be either in dce/dte mode. Choose either from (dce/dte) [dte]:

X.25 Encapsulation
x25 circuit can be either in dce/dte mode. Choose from either dce/dte [dte]: Enter local x25 address: 1234 We will need to map the remote x.25 stations x25 address to the remote stations IP/IPX address Enter remote x25 address: 4321 Do you want to map the remote machines x25 address to IP address? [yes]: IP address for the remote interface: 2.0.0.2 Do you want to map the remote machines x25 address to IPX address? [yes]: IPX address for the remote interface: 40.1234.5678

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-8

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Interface Parameters

Enter Enter Enter Enter Enter

lowest 2-way channel [1]: highest 2-way channel [64]: frame window (K) [7]: Packet window (W) [2]: Packet size (must be powers of 2) [128]:

ATM-DXI Encapsulation
Enter VPI number [1]: Enter VCI number [1]: Do you want to map the remote machines IP address to vpi and vcis? [yes]: IP address for the remote interface: 2.0.0.2 Do you want to map the remote machines IPX address to vpi and vcis? [yes]: IPX address for the remote interface: 40.1234.5678

SMDS Encapsulation
Enter smds address for the local interface: c141.5556.1415 We will need to map the remote smds stations address to the remote stations IP/IPX address Enter smds address for the remote interface: c141.5556.1414 Do you want to map the remote machines smds address to IP address? [yes]: IP address for the remote interface: 2.0.0.2 Do you want to map the remote machines smds address to IPX address? [yes]: IPX address for the remote interface: 40.1234.5678

Serial Cisco IOS Commands Generated

The following is an example of the Cisco IOS commands generated by a typical serial configuration:
interface Serial0/0 encapsulation ppp clock rate 2000000 ip address 2.0.0.1 255.0.0.0

Asynchronous/Synchronous Serial Interface Configuration

This section contains sample configurations for an asynchronous/synchronous serial interface. Enter the values appropriate for your router and network. The messages you see may vary.
Do you want to configure Serial1/0 interface? [yes]: Enter mode (async/sync) [sync]:

Synchronous Configuration
If you select synchronous, you see screen displays similar to the following:
Do you want to configure Serial1/0 interface? [yes]: Enter mode (async/sync) [sync]: Some supported encapsulations are ppp/hdlc/frame-relay/lapb/x25/atm-dxi/smds Choose encapsulation type [hdlc]:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-9

Chapter 2 Configuring Interface Parameters

Using the Setup Command Facility

Note

The following sections describe the prompts for each encapsulation type. For PPP and HDLC encapsulation, no further configuration is needed.
No serial cable seen. Choose mode from (dce/dte) [dte]:

Note

If no cable is plugged in to your router, you need to indicate whether the interface is to be used as DTE or DCE. If a cable is present, the setup command facility determines the DTE/DCE status. If the serial cable is DCE, you see the following prompt:
Configure IP on this interface? [no]: yes Configure IP unnumbered on this interface? [no]: IP address for this interface: 2.0.0.0 Subnet mask for this interface [255.0.0.0]: Class A network is 2.0.0.0, 0 subnet bits; mask is /8 Configure LAT on this interface? [no]:

Frame Relay Encapsulation

The following lmi-types are available to be set, when connected to a frame relay switch [0] none [1] ansi [2] cisco [3] q933a Enter lmi-type [2]:

Note

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-10

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Interface Parameters

LAPB Encapsulation
lapb circuit can be either in dce/dte mode. Choose either from (dce/dte) [dte]:

Asynchronous Configuration
If you select asynchronous, you see screen displays similar to the following:
Do you want to configure Serial1/1 interface? [yes]: Enter mode (async/sync) [sync]: async Configure IP on this interface? [yes]: Configure IP unnumbered on this interface? [no]: IP address for this interface: 2.0.0.0 Subnet mask for this interface [255.0.0.0]: Class A network is 2.0.0.0, 0 subnet bits; mask is /8 Configure LAT on this interface? [no]:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-11

Chapter 2 Configuring Interface Parameters

Using the Setup Command Facility

Configure AppleTalk on this interface? [no]: Configure DECnet on this interface? [no]: Configure CLNS on this interface? [no]: Configure IPX on this interface? [no]: yes IPX network number [8]: Configure Vines on this interface? [no]: Configure XNS on this interface? [no]: Configure Apollo on this interface? [no]:

ISDN BRI Interface Configuration

Use the System Configuration Dialog to configure an ISDN BRI interface. This configuration requires you to enter the ISDN switch type. These switch types are shown in Table 2-1.
Table 2-1 ISDN Switch Types

Country Australia Europe

ISDN Switch Type basic-ts013 basic-1tr6 basic-nwnet3 basic-net3 basic-net5 vn2 vn3

Description Australian TS013 switches German 1TR6 ISDN switches Norwegian NET3 ISDN switches (phase 1) NET3 ISDN switches (UK and others) NET5 switches (UK and others) French VN2 ISDN switches French VN3 ISDN switches Japanese NTT ISDN switches New Zealand NET3 switches AT&T basic rate switches NT DMS-100 basic rate switches National ISDN-1 switches

Japan New Zealand North America

ntt basic-nznet3 basic-5ess basic-dms100 basic-ni1

When you reach the following prompt on the System Configuration Dialog, enter an ISDN switch type from Table 2-1:
BRI interface needs isdn switch-type to be configured Valid switch types are: [0] none..........Only if you don't want to configure BRI. [1] basic-1tr6....1TR6 switch type for Germany [2] basic-5ess....AT&T 5ESS switch type for the US/Canada [3] basic-dms100..Northern DMS-100 switch type for US/Canada [4] basic-net3....NET3 switch type for UK and Europe [5] basic-ni......National ISDN switch type [6] basic-ts013...TS013 switch type for Australia [7] ntt...........NTT switch type for Japan [8] vn3...........VN3 and VN4 switch types for France Choose ISDN BRI Switch Type [2]: Do you want to configure BRI0/0 interface? [yes]: Some encapsulations supported are ppp/hdlc/frame-relay/lapb/x25

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-12

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Interface Parameters

Choose encapsulation type

[ppp]:

Note

The following sections describe the prompts for each encapsulation type. No further configuration is needed for HDLC encapsulation.
Do you have a service profile identifiers (SPIDs) assigned? [no]: y Enter SPID1: 12345 Enter SPID2: 12345

Note

The setup command facility only prompts for the SPID number if you specify basic-5ess, basic-ni1, or basic-dms100 for the switch type.
Do you want to map the remote machine's IP address for the remote interface: Do you want to map the remote machine's IPX address of the remote interface: IP address in dialer map? [yes]: 2.0.0.1 IP address in dialer map? [yes]: 40.0060.34c6.90ed

To get to 2.0.0.1 we will need to make a phone call. Please enter the phone number to call: 1234567890 Configure IP on this interface? [yes]:

Note

If your router has at least one configured LAN interface, you can choose to use an unnumbered IP address on the interface.
Configure IP unnumbered on this interface? [no]: y Assign to which interface [Ethernet0/0]:

Note

If your router does not have a configured LAN interface, you must use a numbered IP address.
IP address for this interface: 2.0.0.0.1 Enter the subnet mask [255.0.0.0]:

PPP Encapsulation
Would you like to enable multilink PPP [yes]: Enter a remote hostname for PPP authentication [Router]: Enter a password for PPP authentication:

Note

The password, which is used by the Challenge Handshake Authentication Protocol (CHAP) authentication process, is case sensitive and must match the remote routers password exactly.

Frame Relay Encapsulation

The following lmi-types are available to be set, when connected to a frame relay switch [0] none [1] ansi [2] cisco [3] q933a Enter lmi-type [2]:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-13

Chapter 2 Configuring Interface Parameters

Using the Setup Command Facility

Note

LAPB Encapsulation
lapb circuit can be either in dce/dte mode Choose either from (dce/dte) [dte]:

ATM-DXI Encapsulation
Enter VPI number [1]: Enter VCI number [1]: Do you want to map the remote machine's IP address to vpi and vci's? [yes]: IP address for the remote interface: 6.0.0.1 Do you want to map the remote machine's IPX address to vpi and vci's? [yes]: IPX address for the remote interface: 40.0060.34c6.90ed

SMDS Encapsulation
Enter smds address for the local interface: c141.5556.1415 We will need to map the remote smds station's address to the remote stations IP address Enter smds address for the remote interface: c141.5556.1414 Do you want to map the remote machine's smds address to IP address? [yes]: IP address for the remote interface: 2.0.0.1 Do you want to map the remote machine's smds address to IP address? [yes]: IPX address for the remote interface: 40.0060.34c6.90ed

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-14

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Interface Parameters

X.25 Encapsulation
x25 circuit can be either in dce/dte mode. Choose from either dce/dte [dte]: Enter local x25 address: 1234 We will need to map the remote x.25 station's x25 address to the remote stations IP/IPX address Do you want to map the remote machine's x25 address to IP address? [yes]: IP address for the remote interface: 6.0.0.1 Do you want to map the remote machine's x25 address to IPX address? [yes]: IPX address for the remote interface: 40.0060.34c6.90ed Enter remote x25 address: 4321 Enter lowest 2-way channel [1]: Enter highest 2-way channel [64]: Enter frame window (K) [7]: Enter Packet window (W) [2]: Enter Packet size (must be powers of 2) [128]:

ISDN BRI Line Configuration

Before using a router with an ISDN BRI interface, you must order a correctly configured ISDN BRI line from your local telecommunications service provider. The ordering process varies from provider to provider and from country to country. However, here are some general guidelines:

Ask for two channels to be called by one number. Ask for delivery of calling line identification, also known as caller ID or Automatic Number Identification (ANI). If the router will be the only device attached to the ISDN BRI line, ask for point-to-point service and a data-only line. If you plan to connect another ISDN device (such as an ISDN telephone) to the ISDN BRI line through the router, ask for point-to-multipoint service (subaddressing is required) and a voice-and-data line.

ISDN BRI Provisioning by Switch Type

ISDN BRI provisioning refers to the types of services provided by the ISDN BRI line. Although provisioning is performed by your ISDN BRI service provider, you must tell the provider what you want. Table 2-2 lists the provisioning you should order for the router based on switch type.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-15

Chapter 2 Configuring Interface Parameters

Using the Setup Command Facility

Table 2-2

ISDN Provisioning by Switch Type

Switch Type 5ESS Custom BRI

Provisioning
For data only

2 B channels for data Point to point Terminal type = E 1 directory number (DN) assigned by service provider MTERM = 1 Request delivery of calling line ID on Centrex lines Set speed for ISDN calls to 56 kbps outside local exchange 5ESS Custom BRI
For voice and data

(Use these values only if you have an ISDN telephone connected.) 2 B channels for voice or data MultiPoint Terminal type = D 2 directory numbers assigned by service provider 2 service profile identifiers (SPIDs) required, assigned by service provider MTERM = 2 Number of call appearances = 1 Display = No Ringing/idle call appearances = idle Autohold= no Onetouch = no Request delivery of calling line ID on Centrex lines Set speed for ISDN calls to 56 kbps outside local exchange Directory number 1 can hunt to directory number 2 5ESS National ISDN (NI-1) BRI Terminal type = A 2 B channels for voice and data 2 directory numbers assigned by service provider 2 SPIDs required; assigned by service provider Set speed for ISDN calls to 56 kbps outside local exchange Directory number 1 can hunt to directory number 2 2 B channels for voice and data 2 directory numbers assigned by service provider 2 SPIDs required; assigned by service provider Functional signaling Dynamic terminal endpoint identifier (TEI) assignment Maximum number of keys = 64 Release key = no, or key number = no Ringing indicator = no EKTS = no PVC = 2 Request delivery of calling line ID on Centrex lines Set speed for ISDN calls to 56 kbps outside local exchange Directory number 1 can hunt to directory number 2

DMS-100 BRI

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-16

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Interface Parameters

Defining ISDN Service Profile Identifiers

Some service providers assign service profile identifiers (SPIDs) to define the services subscribed to by an ISDN device. If your service provider requires SPIDs, your ISDN device cannot place or receive calls until it sends a valid SPID to the service provider when initializing the connection. A SPID is usually a seven-digit telephone number plus some optional numbers, but service providers may use different numbering schemes. SPIDs have significance at the local access ISDN interface only; remote routers are never sent the SPID. Currently, only DMS-100 and NI-1 switch types require SPIDs. Two SPIDs are assigned for the DMS-100 switch type, one for each B channel. The AT&T 5ESS switch type may support SPIDs, but Cisco recommends that you set up that ISDN service without SPIDs. If your service provider assigns you SPIDs, you must define these SPIDs on the router. To define SPIDs and the local directory number (LDN) on the router for both ISDN BRI B channels, use the following isdn spid commands:
Router(config-if)# isdn spid1 spid-number [ldn] Router(config-if)# isdn spid2 spid-number [ldn]

Note

Although the LDN is an optional parameter in the command, you may need to enter it so the router can answer calls made to the second directory number.

E1/T1 ISDN PRI Configuration

This section contains a sample configuration for the channelized E1/T1 ISDN PRI interface. Enter the values appropriate for your router and network. The messages you see may vary.
The following ISDN switch types are available: [0] none............If you do not want to configure ISDN [1] primary-4ess....AT&T 4ESS switch type for US and Canada [2] primary-5ess....AT&T 5ESS switch type for US and Canada [3] primary-dms100..Northern Telecom switch type for US and Canada [4] primary-net5....European switch type for NET5 [5] primary-ni......National ISDN Switch type for the U.S [6] primary-ntt.....Japan switch type [7] primary-ts014...Australian switch type Choose ISDN PRI Switch Type [2]: Configuring controller T1 1/0 in pri or channelized mode Do you want to configure this interface controller? [no]: Will you be using PRI on this controller? [yes]:

E1/T1 PRI Mode

The following is an example of a E1/T1 PRI mode configuration using the setup command facility:
The following framing types are available: esf | sf Enter the framing type [esf]: The following linecode types are available: ami | b8zs Enter the line code type [b8zs]: Enter number of time slots [24]: Do you want to configure Serial1/0:23 interface? [yes]:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-17

Chapter 2 Configuring Interface Parameters

Using the Setup Command Facility

Configuring the PRI D-channel Would you like to enable multilink PPP? [yes]: Configure IP on this interface? [no]: y Configure IP unnumbered on this interface? [no]: y Assign to which interface [Ethernet0/0]: All users dialing in through the PRI will need to be authenticated using CHAP. The username and password are case sensitive. Enter more username and passwords for PPP authentication? [no]: y Enter the username used for dial-in CHAP authentication [Router]: of the user dialling in on PRI: Enter more username and passwords for PPP authentication? [no]:

Enter the PPP password

E1 Channelized Mode
The following is an example of an E1 channelized mode configuration using the setup command facility:
The following framing types are available: no-crc4 | crc4 Enter the framing type [crc4]: The following linecode types are available: ami | hdb3 Enter the line code type [hdb3]: Do you want to configure Serial1/1:0 interface?: [Yes]: Configuring the Channelized E1/T1 serial channels Some encapsulations supported are ppp/hdlc/frame-relay/lapb/atm-dxi/smds/x25 Choose encapsulation type [ppp]: Configure IP on this interface? [no]: y Configure IP unnumbered on this interface? [no]: IP address for this interface: 3.0.0.1 Subnet mask for this interface [255.0.0.0]: Class A network is 3.0.0.0, 8 subnet bits; mask is /8

Note

The following sections describe the prompts for each encapsulation type. No further configuration is needed for HDLC encapsulation.

PPP Encapsulation
Would you like to enable multilink PPP [yes]: Enter a remote hostname for PPP authentication [Router]: Enter a password for PPP authentication:

Note

The password, which is used by the Challenge Handshake Authentication Protocol (CHAP) authentication process, is case sensitive and must match the remote routers password exactly.

Frame Relay Encapsulation

The following lmi-types are available to be set, when connected to a frame relay switch [0] none

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-18

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Interface Parameters

[1] ansi [2] cisco [3] q933a Enter lmi-type [2]:

Note

LAPB Encapsulation
lapb circuit can be either in dce/dte mode Choose either from (dce/dte) [dte]:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-19

Chapter 2 Configuring Interface Parameters

Using the Setup Command Facility

T1 Channelized Mode
The following is an example of a T1 channelized mode configuration using the setup command facility:
The following framing types are available: esf | sf Enter the framing type [esf]: The following linecode types are available: ami | b8zs Enter the line code type [b8zs]: T1 is capable of being configured for channel 1-24 Enter number of time slots [24]: 3 Configure more channel groups? [no]: y Enter number of time slots [21]: 3 Configure more channel groups? [no]: y Enter number of time slots [18]: 3 Configure more channel groups? [no]: y Enter number of time slots [15]: Configure more channel groups? [no]:

Note

The following sections describe the prompts for each encapsulation type. No further configuration is needed for HDLC encapsulation.

PPP Encapsulation
Would you like to enable multilink PPP [yes]: Enter a remote hostname for PPP authentication [Router]: Enter a password for PPP authentication:

Note

The password, which is used by the Challenge Handshake Authentication Protocol (CHAP) authentication process, is case sensitive and must match the remote routers password exactly.

Frame Relay Encapsulation

The following lmi-types are available to be set,

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-20

OL-1957-04

Chapter 2

Using the Setup Command Facility Configuring Interface Parameters

when connected to a frame relay switch [0] none [1] ansi [2] cisco [3] q933a Enter lmi-type [2]:

Note

LAPB Encapsulation
lapb circuit can be either in dce/dte mode Choose either from (dce/dte) [dte]:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-21

Chapter 2 Configuring Interface Parameters

Using the Setup Command Facility

IPX address for the remote interface: 40.0060.34c6.90ed

1-Port, 4-Wire 56-kbps DSU/CSU Configuration Setup

This section describes using setup command facility to configure a 1-port, 4-wire 56-kbps DSU/CSU WAN interface card. It discusses the following:

Choosing Circuit-Switched or Dedicated-Line Service Switched Mode Dedicated Mode

Choosing Circuit-Switched or Dedicated-Line Service

The switched-56 WAN interface card is configured for dedicated or leased-line service by default, but it can also be configured for circuit-switched service. Depending on the type of data transmissions you typically use, you can configure the switched-56 WAN interface card for circuit-switched or dedicated-line service. Generally, circuit-switched service is ideal for short duration data transmissions or as an alternative route if a dedicated line fails. For example, circuit-switched service is ideal for sending electronic mail messages or doing such tasks as updating inventory and ordering records from one network database to another at the end of each day. Dedicated service is ideal for heavy network traffic. Dedicated service is ideal if you need a constant network connection or you need connection for more than eight hours per day.

Switched Mode
The following is an example of a 1-port, 4-wire 56-kbps DSU/CSU switched-mode configuration using the setup command facility:
Do you want to configure Serial0/0 interface? [yes]: Some encapsulations supported are ppp/hdlc/frame-relay/lapb/atm-dxi/smds/x25 Choose encapsulation type [ppp]: Switched 56k interface may either be in switched/Dedicated mode Choose from either (switched/dedicated) [switched]: The following switched carrier types are to be set when in switched mode (at&t, sprint or other) Choose carrier (at&t/sprint/other) [other]: Do you want to map the remote machine's ip address in dialer map? [yes]: IP address for the remote interface : 1.0.0.2 Do you want to map the remote machine's ipx address in dialer map? [yes]: IPX address for the remote interface : 40.0060.34c6.90ed

Note

The setup command facility will ask for only one telephone number for both IP and IPX (if enabled).
Please enter the phone number to call : 1234567890 Configure IP on this interface? [yes]: IP address for this interface: 1.0.0.1 Subnet mask for this interface [255.0.0.0] : Class A network is 1.0.0.0, 8 subnet bits; mask is /8

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-22

OL-1957-04

Chapter 2

Using the Setup Command Facility Completing the Configuration

Dedicated Mode
The following is an example of a 1-port, 4-wire 56-kbps DSU/CSU dedicated-mode configuration using the setup command facility:
Do you want to configure Serial0/0 interface? [yes]: Some encapsulations supported are ppp/hdlc/frame-relay/lapb/atm-dxi/smds/x25 Choose encapsulation type [ppp]: Switched 56k interface may either be in switched/Dedicated mode Choose from either (switched/dedicated) [switched]: dedi When in dds mode, the clock for sw56 module can either from line/internal. Choose clock from (line/internal) [line]:

Note

If internal is selected, speed cannot be set to auto. Auto-sensing is only allowed when the clock source is line.
When in dds mode, the clock for sw56 module can either from line/internal. Choose clock from (line/internal) [line]: internal Warning: internal can be choose only when connected back to back. Serial interface needs clock rate to be set in dce mode. The following clock rates are supported on the serial interface. auto, 2.4, 4.8, 9.6, 19.2, 38.4 56, 64 choose clock rate from above [56]: Configure IP on this interface? [yes]: IP address for this interface: 1.0.0.1 Subnet mask for this interface [255.0.0.0] : Class A network is 1.0.0.0, 8 subnet bits; mask is /8

Completing the Configuration

When you have provided all the information prompted for by the setup command facility, the configuration appears. Some examples of the configurations of the Cisco 2600 Series, Cisco 3600 series, and Cisco 3700 series routers are shown inAppendix A, Configuration Examples. To complete your router configuration, do the following:
Step 1

A setup command facility prompt asks if you want to save this configuration. If you answer no, the configuration information you entered is not saved, and you return to the router enable prompt (2600#). Type setup to return to the System Configuration Dialog. If you answer yes, the configuration is saved and your are returned to the EXEC prompt(2600>).
Use this configuration? {yes/no} : yes Building configuration... Use the enabled mode 'configure' command to modify this configuration.

Press RETURN to get started!

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

2-23

Chapter 2 Where to Go Next

Using the Setup Command Facility

%LINK-3-UPDOWN: %LINK-3-UPDOWN: %LINK-3-UPDOWN: %LINK-3-UPDOWN: %LINK-3-UPDOWN: %LINK-3-UPDOWN: %LINK-3-UPDOWN: %LINK-3-UPDOWN:

Interface Interface Interface Interface Interface Interface Interface Interface

Ethernet0/0, changed state to up Ethernet0/1, changed state to up Serial0/0, changed state to up Serial0/1, changed state to down Serial0/2, changed state to down Serial1/0, changed state to up Serial1/1, changed state to down Serial1/2, changed state to down

<Additional messages omitted.>

Step 2

When the messages stop displaying on your screen, press Return to get the 2600> prompt.
Note

If you see the next message, it means that no other AppleTalk routers were found on the network attached to the port.

%AT-6-ONLYROUTER: Ethernet0/0: AppleTalk port enabled; no neighbors found

Step 3

The 2600> prompt indicates that you are now at the command-line interface (CLI) and you have just completed a basic router configuration. However, this is not a complete configuration. At this point you have two choices:

Run the setup command facility again and create another configuration. Enter the following:

2600> enable Password: password 2600# setup

Modify the existing configuration or configure additional features with the CLI as described in Chapter 3, Configuring with the Command-Line Interface.

Where to Go Next
At this point you can proceed to the following:

Chapter 3, Configuring with the Command-Line Interface, to learn how to use the CLI to configure additional features. The Cisco IOS software configuration guide and command reference publications for more advanced configuration topics. These publications are available on Cisco.com, the Documentation CD-ROM that came with your router, or you can order printed copies. For more information, refer to Obtaining Documentation.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

2-24

OL-1957-04

C H A P T E R

Configuring with the Command-Line Interface

This chapter describes how to use the Cisco IOS software command-line interface (CLI) to configure basic router functionality, including:

Configuring the Host Name and Password, page 3-2 Configuring 1-Port and 2-Port Ethernet Interfaces, page 3-3 Configuring Fast Ethernet Interfaces, page 3-4 Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards, page 3-5 Configuring 16-Port and 32-Port Asynchronous Network Modules, page 3-9 Configuring ISDN BRI WAN Interface Cards, page 3-10 Configuring T1 and E1 Interfaces, page 3-14 Configuring T1 (FT1) WAN Interface Cards, page 3-18 Configuring ATM Interfaces, page 3-20 Configuring Inverse Multiplexing for ATM Interfaces, page 3-22 Configuring Analog Modem Interfaces, page 3-26 Configuring Wireless Multipoint Interfaces, page 3-28 Configuring 1-Port ADSL WAN Interface Card, page 3-29 Configuring the NM-AIC-64, Contact Closure Network Module, page 3-34 Configuring the 1-Port HSSI Network Module, page 3-46 Configuring the Compression Network Module for the Cisco 3600 Series Routers, page 3-49 Configuring the Digital Modem Network Module for the Cisco 3640 Router, page 3-50 Configuring G.SHDSL on a Cisco Router, page 3-60 Where to Go Next, page 3-64

Follow the procedures in this chapter to configure the router manually, or if you want to change the configuration after you have run the setup command facility Using the Setup Command Facility, page 2-1. This chapter does not describe every configuration possibleonly a small portion of the most commonly used configuration procedures. For advanced configuration topics, refer to the Cisco IOS configuration guide and command reference publications. These publications are available on the Documentation CD-ROM that came with your router, on the World Wide Web from Ciscos home page, or you can order printed copies separately.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-1

Chapter 3 Configuring the Host Name and Password

Configuring with the Command-Line Interface

Note

If you skipped the previous chapter, Chapter 2, Using the Setup Command Facility, and you have never configured a Cisco router, go back to that chapter and read it now. The chapter contains important information you need to successfully configure your router.

Configuring the Host Name and Password

One of the first configuration tasks you might want to do is configure the host name and set an encrypted password. Configuring a host name allows you to distinguish multiple Cisco routers from each other. Setting an encrypted password allows you to prevent unauthorized configuration changes. Command
Step 1 Router> enable
Password: password Router#

Purpose Enter enable mode. Enter the password. You have entered enable mode when the prompt changes to Router#. Enter global configuration mode. You have entered global configuration mode when the prompt changes to Router(config)#. Change the name of the router to a meaningful name. Substitute your host name for Router. Enter an enable secret password. This password provides access to privileged EXEC mode. When a user types enable at the EXEC prompt (Router> ), they must enter the enable secret password to gain access to configuration mode. Substitute your enable secret for guessme. Enter line configuration mode to configure the console port. When you enter line configuration mode, the prompt changes to Router(config-line)#. Prevent the routers EXEC facility from timing out if you do not type any information on the console screen for an extended period. Exit back to global configuration mode.

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router(config)# hostname Router

Router(config)#

Step 4 Router(config)# enable secret guessme

Step 5 Router(config)# line con 0

Router(config-line)# exec-timeout 0 0

Router(config-line)# exit Router(config)#

Verifying the Host Name and Password

To verify that you configured the correct host name and password:
Step 1

Enter the show config command:

Router(config)# show config

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-2

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring 1-Port and 2-Port Ethernet Interfaces

Using 1888 out of 126968 bytes ! version XX.X . . . ! hostname Router ! enable secret 5 $1$60L4$X2JYOwoDc0.kqa1loO/w8/ . . .

Check the host name and encrypted password displayed near the top of the command output.
Step 2

Exit global configuration mode and attempt to re-enter it using the new enable password:
Router# exit . . . Router con0 is now available Press RETURN to get started. Router> enable Password: guessme Router#

Tip

If you are having trouble, check the following:

Caps Lock is off. You entered the correct passwords. Passwords are case sensitive.

Configuring 1-Port and 2-Port Ethernet Interfaces

You can configure Ethernet interfaces manually by entering Cisco IOS commands on the command line. This method, called configuration mode, provides the greatest power and flexibility.

Timesaver

Before you begin, disconnect all WAN cables from the router to keep it from trying to run the AutoInstall process. The router tries to run AutoInstall whenever you power it on, if there is a WAN connection on both ends and the router does not have a valid configuration file stored in nonvolatile random-access memory (NVRAM) (for instance, when you add a new interface). It can take several minutes for the router to determine that AutoInstall is not connected to a remote Transmission Control Protocol/Internet Protocol (TCP/IP) host. Before you begin configuring the Ethernet interface, make sure you:

Connect a console to the router. Power on the router.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-3

Chapter 3 Configuring Fast Ethernet Interfaces

Configuring with the Command-Line Interface

Command
Step 1 Router> enable
Password: password Router#

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# interface ethernet 0/0

Router(config-if)#

Step 5 Router(config-if)# ip address 172.16.74.3

255.255.255.0

Step 6 Router(config-if)# appletalk static

cable-range 3-3 Router(config-if)# appletalk zone ZZEth Router(config-if)# ipx network B005

Step 7 Router(config-if)# exit

Step 8 Router(config)# Ctrl-z

Router#

When you finish configuring interfaces, return to enable mode.

Configuring Fast Ethernet Interfaces

To configure a Fast Ethernet interface, use the configuration software provided with your router or network module, if any. Otherwise, for greatest power and flexibility use configuration mode (manual configuration). In this mode, you enter Cisco IOS commands at the router prompt.
Note

Before you begin, disconnect all WAN cables from the router to keep it from trying to run the AutoInstall process. The router tries to run AutoInstall whenever you power it on if there is a WAN connection on both ends and the router does not have a valid configuration file stored in NVRAM (for instance, when you add a new interface). It can take several minutes for the router to determine that AutoInstall is not connected to a remote Transmission Control Protocol/Internet Protocol (TCP/IP) host. This section describes basic configuration, including enabling the interface and specifying IP routing. Depending on your own requirements and the protocols you plan to route, you might also need to enter other configuration commands. Before you begin configuring the interfaces, make sure you:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-4

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards

Command
Step 1 Router> enable
Password: password Router#

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# interface fastethernet 0/0 Enter interface configuration mode. You have
Router(config-if)#

Step 5 Router(config-if)# ip address 172.16.74.3

255.255.255.0

Step 6 Router(config-if)# appletalk static

cable-range 3-3 Router(config-if)# appletalk zone ZZEth Router(config-if)# ipx network B005

Step 7 Router(config-if)# exit

Step 8 Router(config)# Ctrl-z

Router#

When you finish configuring interfaces, return to enable mode.

Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards

You can configure the serial interfaces on your asynchronous/synchronous serial network module or WAN interface card manually by entering Cisco IOS commands on the command line. This method, called configuration mode, provides the greatest power and flexibility.

Timesaver

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-5

Chapter 3 Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards

Configuring with the Command-Line Interface

memory (NVRAM) (for instance, when you add a new interface). It can take several minutes for the router to determine that AutoInstall is not connected to a remote Transmission Control Protocol/Internet Protocol (TCP/IP) host. Before you begin configuring the asynchronous/synchronous serial interface, make sure you:

Connect a console to the router. Power on the router. Purpose Enter enable mode. Enter the password. You have entered enable mode when the prompt changes to Router#. Enter global configuration mode. You have entered global configuration mode when the prompt changes to Router(config)#. Enable routing protocols as required for your global configuration. This example uses IP routing, AppleTalk routing, and Internetwork Packet Exchange (IPX) routing. Enter the interface configuration mode. You have entered interface configuration mode when the prompt changes to Router(config-if)#. Assign the IP address and subnet mask to the interface. Configure routing protocols on the interface. You must have previously enabled these protocols as part of global configuration. In this example, AppleTalk and IPX are being configured on the interface. All serial ports are initially configured as synchronous. Enter this command if you want to configure the port as asynchronous. Configure asynchronous parameters according to your needs. Configure the asynchronous line setting. Specify the time that the interface waits in controlled carrier mode. See Table 3-1 for a list of half-duplex timer commands. To use a port in DCE mode, connect a DCE cable and set the internal transmit clock signal (TXC) speed in bits per second. See Table 3-2 through Table 3-5 for a list of clock rate settings for your specific interface. (For ports used in DTE mode, the router automatically uses the external timing signal.)

Command
Step 1 Router> enable
Password: password Router#

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# interface serial 0/0

Router(config-if)#

Step 5 Router(config-if)# ip address 172.16.74.1

255.255.255.0

Step 6 Router(config-if)# appletalk static

cable-range 5-5 Router(config-if)# appletalk zone ZZSerial Router(config-if)# ipx network B003

Step 7 Router(config-if)# physical-layer async

Step 8 Router(config-if)# async mode dedicated

Router(config-if)# async default routing

Step 9 Router(config-if)# line async <#> Step 10 Router(config-if)# half-duplex timer

dcd-drop-delay 100

Step 11 Router(config-if)# clockrate 7200

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-6

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards

Command
Step 12 Router(config-if)#
dce-terminal-timing-enable

Purpose When a port is operating in DCE mode, the default operation is for the DCE to send serial clock transmit (SCT) and serial clock receive (SCR) clock signals to the DTE, and for the DTE to return a serial clock transmit external (SCTE) signal to the DCE. If the DTE does not return SCTE, enter this command to configure the DCE port to use its own clock signal.

Step 13 Router(config-if)# invert-txc

Routers that use long cables might experience high error rates when operating at higher transmission speeds, because the clock and data signals can shift out of phase. If a DCE port is reporting a high number of error packets, inverting the clock using this command can often correct the shift.

Step 14 Router(config-if)# nrzi-encoding

All serial interfaces support both nonreturn to zero (NRZ) and nonreturn to zero inverted (NRZI) formats. NRZ is the default; NRZI is commonly used with EIA/TIA-232 connections in IBM environments. To enable NRZI encoding on an interface, enter this command. Exit back to global configuration mode. Repeat Step 4 through Step 14 if your router has more that one serial interface that you need to configure.

Step 15 Router(config-if)# exit

Step 16 Router(config)# Ctrl-z

Router#

When you finish configuring interface, return to enable mode.

Table 3-1

Half-Duplex Timer Commands

Timer CTS delay1 CTS drop timeout DCD drop delay DCD transmission start delay RTS2 drop delay RTS timeout Transmit delay

Syntax half-duplex timer cts-delay half-duplex timer cts-drop-timeout half-duplex timer dcd-drop-delay half-duplex timer dcd-txstart-delay half-duplex timer rts-drop-delay half-duplex timer rts-timeout half-duplex timer transmit-delay

Default Setting (Milliseconds) 100 5000 100 100 100 2000 0

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-7

Chapter 3 Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards

Configuring with the Command-Line Interface

1. CTS = Clear To Send. 2. RTS = Request To Send.

Table 3-2

Clock Rate Settings for 1-Port/2-Port Serial WAN Interface Card in Synchronous Mode

Timer (bits per second) 1200 2400 4800 9600 14400 19200 28800 32000

Syntax (bits per second) 38400 56000 57600 64000 72000 115200 125000 128000

Default Setting (bits per second) 148000 500000 800000 1000000 1300000 2000000 4000000 148000

Table 3-3

Clock Rate Settings for 1-Port/2-Port Serial WAN Interface Card in Asynchronous Mode

Timer (bits per second) 1200 2400 4800 9600 14400 19200

Syntax (bits per second) 28800 32000 38400 56000 57600 64000

Default Setting (bits per second) 72000 115200 125000 128000

Table 3-4

Clock Rate Settings for 2-Port Asynchronous/Synchronous Serial WAN Interface Card

Timer (bits per second) 1200 2400 4800 9600 14400 19200

Syntax (bits per second) 28800 32000 38400 56000 57600 64000

Default Setting (bits per second) 72000 115200 125000 128000

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-8

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring 16-Port and 32-Port Asynchronous Network Modules

Table 3-5

Clock Rate Settings for 4-Port/8-Port Asynchronous/Synchronous Serial Network Module

Timer (bits per second) 300 1200 2400 4800 9600 14400

Syntax (bits per second) 19200 28800 32000 38400 56000 57600

Default Setting (bits per second) 64000 72000 115200 128000

Configuring 16-Port and 32-Port Asynchronous Network Modules

You can configure the asynchronous interface manually by entering Cisco IOS commands on the command line. This method, called configuration mode, provides the greatest power and flexibility.

Timesaver

Before you begin, disconnect all WAN cables from the router to keep it from trying to run the AutoInstall process. The router tries to run AutoInstall whenever you power it ON, if there is a WAN connection on both ends and the router does not have a valid configuration file stored in nonvolatile random-access memory (NVRAM) (for instance, when you add a new interface). It can take several minutes for the router to determine that AutoInstall is not connected to a remote Transmission Control Protocol/Internet Protocol (TCP/IP) host. Before you begin configuring the asynchronous interface, make sure you:

Command
Step 1 Router> enable
Password: password Router#

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-9

Chapter 3 Configuring ISDN BRI WAN Interface Cards

Configuring with the Command-Line Interface

Command
Step 4 Router(config)# interface async 45
Router(config-if)#

Purpose Enter the interface configuration mode and specify the asynchronous interface to configure. You have entered interface configuration mode when the prompt changes to Router(config-if)#. Assign the IP address and subnet mask to the interface. Configure routing protocols on the interface. You must have previously enabled these protocols as part of global configuration. In this example, AppleTalk and IPX are being configured on the interface. Configure asynchronous parameters according to your needs.

Step 5 Router(config-if)# ip address 172.16.74.1

255.255.255.0

Step 6 Router(config-if)# appletalk static

cable-range 5-5 Router(config-if)# appletalk zone ZZAsync Router(config-if)# ipx network B003

Step 7 Router(config-if)# async mode dedicated

Router(config-if)# async default routing Router(config-if)# line async 45 Router(config-if)# speed 115200

Step 8 Router(config-if)# exit

Return to the global configuration mode and repeat Step 4 through Step 7 if your router has more than one interface that you need to configure. Return to enable mode.

Step 9 Router(config)# Ctrl-z

Router#

Configuring ISDN BRI WAN Interface Cards

You can configure the interfaces on your BRI WAN interface card manually by entering Cisco IOS commands on the command line. This method, called configuration mode, provides the greatest power and flexibility.

Timesaver

Connect a console to the router. Power on the router.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-10

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring ISDN BRI WAN Interface Cards

Command
Step 1 Router> enable
Password: password Router#

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router(config)# isdn switch-type

basic-5ess

Switch types configured in interface configuration mode override this setting for the configured interface.

Step 4 Router(config)# ip routing

Router(config)# appletalk routing Router(config)# ipx routing

Enable routing protocols as required for your global configuration. This example uses IP routing, AppleTalk routing, and Internetwork Packet Exchange (IPX) routing. Enter the interface configuration mode. You have entered interface configuration mode when the prompt changes to Router(config-if)#. Assign the IP address and subnet mask to the interface. If you are configuring this interface for voice, enter the switch type instead of an IP address. Configure routing protocols on the interface. You must have previously enabled these protocols as part of global configuration. In this example, AppleTalk and IPX are being configured on the interface. If you are configuring this router for voice, use the isdn incoming-voice modem command. Exit back to global configuration mode. Repeat Step 5 through Step 7 if your router has more than one BRI interface that you need to configure.

Step 5 Router(config)# interface bri 0/0

Router(config-if)#

Step 6 Router(config-if)# ip address 172.16.74.2

255.255.255.0 Router(config-if)# isdn switch-type basic-5ess

Step 7 Router(config-if)# appletalk static

cable-range 5-5 Router(config-if)# appletalk zone ZZBRI Router(config-if)# ipx network B004 Router(config-if)# isdn incoming-voice modem

Step 8 Router(config-if)# exit

Step 9 Router(config-if)# memory-size iomem 40

By default, the router allocates 25 percent of DRAM to shared memory (used for data transmitted or received by network modules and WAN interface cards). If your router includes 16 or more ISDN BRI interfaces, you must increase the amount of shared memory by entering the memory-size iomem command. This example increases shared memory from 25 percent to 40 percent. When you finish configuring interfaces, return to enable mode.

Step 10 Router(config)# Ctrl-z

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-11

Chapter 3 Configuring ISDN BRI WAN Interface Cards

Configuring with the Command-Line Interface

Table 3-6

ISDN Switch Types

Country Australia Europe

ISDN Switch Type basic-ts013 basic-1tr6 basic-nwnet3 basic-net3 vn2 vn3

Description Australian TS013 switches German 1TR6 ISDN switches Norwegian NET3 ISDN switches (phase 1) NET3 ISDN switches (UK and others) French VN2 ISDN switches French VN3 ISDN switches Japanese NTT ISDN switches New Zealand NET3 switches AT&T basic rate switches NT DMS-100 basic rate switches National ISDN-1 switches

Japan New Zealand North America

ntt basic-nznet3 basic-5ess basic-dms100 basic-nil1

Configuring ISDN BRI Lines

ISDN BRI Provisioning by Switch Type

ISDN BRI provisioning refers to the types of services provided by the ISDN BRI line. Although provisioning is performed by your ISDN BRI service provider, you must tell the provider what you want. Table 3-7 lists the provisioning you should order for your router.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-12

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring ISDN BRI WAN Interface Cards

Table 3-7

ISDN Provisioning by Switch Type

Switch Type 5ESS Custom BRI

Provisioning For data only: 2 B channels for data Point to point Terminal type = E 1 directory number (DN) assigned by service provider MTERM = 1 Request delivery of calling line ID on Centrex lines Set speed for ISDN calls to 56 kbps outside local exchange

5ESS Custom BRI

For voice and data: (Use these values only if you have an ISDN telephone connected.)| 2 B channels for voice or data Multipoint Terminal type = D 2 directory numbers assigned by service provider 2 service profile (SPIDs) required, assigned by service provider MTERM = 2 Number of cal appearances = 1 Display = No Ringing/idle call appearances = 1 Autohold = no Onetouch = no Request delivery of calling line ID on Centrex lines Set speed for ISDN calls to 56 kbps outside local exchange Directory number 1 can hunt to directory number 2

5ESS National ISDN (NI-1) BRI Terminal type = A 2 B channels for voice or data 2 directory numbers assigned by service provider 2 SPIDs required, assigned by service provider Set speed for ISDN calls to 56 kbps outside local exchange Directory number 1 can hunt to directory number 2 DMS-100 BRI 2 B channels for voice or data 2 directory numbers assigned by service provider 2 SPIDs required, assigned by service provider Functional signaling Dynamic terminal endpoint identifier (TEI) assignment Maximum number of keys = 64 Release key = no, or key number = no Ringing indicator = no EKTS = no PVC = 2 Request delivery of calling line ID on Centrex lines Set speed for ISDN calls to 56 kbps outside local exchange Directory number 1 can hunt to directory number 2

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-13

Chapter 3 Configuring T1 and E1 Interfaces

Configuring with the Command-Line Interface

Defining ISDN Service Profile Identifiers

Some service providers assign service profile identifiers (SPIDs) to define the services to which an ISDN device subscribes. If your service provider requires SPIDs, your ISDN device cannot place or receive calls until it sends a valid SPID to the service provider when initializing the connection. A SPID is usually a seven-digit telephone number plus some optional numbers, but service providers might use different numbering schemes. SPIDs have significance at the local access ISDN interface only; remote routers are never sent the SPID. Currently, only DMS-100 and NI-1 switch types require SPIDs. Two SPIDs are assigned for the DMS-100 switch type, one for each B channel. The AT&T 5ESS switch type might support SPIDs, but Cisco recommends that you set up that ISDN service without SPIDs. If your service provider assigns you SPIDs, you must define these SPIDs on the router. To define SPIDs and the local directory number (LDN) on the router for both ISDN BRI B channels, use the following isdn spid commands:
Router (config-if)# isdn spid1 Router (config-if)# isdn spid2

spid-number [ldn] spid-number [ldn ]

Note

Although the LDN is an optional parameter in the command, you might need to enter it so the router can answer calls made to the second directory number. For further information on configuring ISDN, see the chapters Configuring ISDN and Configuring DDR in the Wide-Area Networking Configuration Guide publication, for your Cisco IOS software release.

Configuring T1 and E1 Interfaces

To configure an ISDN PRI interface or T1/E1 multiflex trunk interface, use the configuration software provided with your router or network module, if any. Otherwise, for greatest power and flexibility use configuration mode (manual configuration). In this mode, you enter Cisco IOS commands at the router prompt.
Note

Connect a console to the router. Power on the router.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-14

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring T1 and E1 Interfaces

Configuring T1 Interfaces
Use the following procedure to configure a new T1, CT1/PRI or CT1/PRI-CSU interface or to change the configuration of an existing interface. Command
Step 1 Router> enable
Password: password Router#

Purpose Enter enable mode. Enter the password. You have entered enable mode when the prompt changes to Router#. Enter global configuration mode. You have entered global configuration mode when the prompt changes to Router(config)#. Enable routing protocols as required for your global configuration. This example uses IP routing, AppleTalk routing, and Internetwork Packet Exchange (IPX) routing. Select the CT1/PRI interface to configure. This example configures a T1 interface in slot 1 and unit 0. Specify which end of the circuit provides clocking. The clock source should be set to use internal clocking only for testing the network or if the full T1 line is used as the channel group. Only one end of the T1 line should be set to internal. Specify the framing type. Specify the line code format. Specify the channel group and time slots to be mapped. For multiflex trunk interfaces, only channel 0 can be configured. Configure each channel group as a virtual serial interface. Specify the T1 interface, unit number, and channel group to modify. Assign an IP address and subnet mask to the interface. Configure routing protocols on the interface. You must have previously enabled these protocols as part of global configuration. In this example, AppleTalk and IPX are being configured on the interface. Exit back to global configuration mode. Return to Step 4 if your router has more than one CT1/PRI interface that you need to configure.

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# controller t1 1/0

Step 5 Router(config-controller)# clock source

line

Step 6 Router(config-controller)# framing esf Step 7 Router(config-controller)# linecode b8zs Step 8 Router(config-controller)# channel-group 0
timeslots 1,3-5,7

Step 9 Router(config-controller)# interface serial

1/0:0

Step 10 Router(config-if)# ip address 10.1.15.1

255.255.255.0

Step 11 Router(config-if)# appletalk static

cable-range 3-3 Router(config-if)# appletalk zone ZZEth Router(config-if)# ipx network B005

Step 12 Router(config-if)# exit

Step 13 Router(config)# Ctrl-z

Router#

When you finish configuring interfaces, return to enable mode.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-15

Chapter 3 Configuring T1 and E1 Interfaces

Configuring with the Command-Line Interface

Configuring E1 Interfaces
Use the following procedure to configure a new E1 or CE1/PRI interface (balanced or unbalanced) or to change the configuration of an existing interface. Command
Step 1 Router> enable
Password: password Router#

Purpose Enter enable mode. Enter the password. You have entered enable mode when the prompt changes to Router#. Enter global configuration mode. You have entered global configuration mode when the prompt changes to Router(config)#. Enable routing protocols as required for your global configuration. This example uses IP routing, AppleTalk routing, and Internetwork Packet Exchange (IPX) routing. Select the CE1/PRI interface to configure. This example configures an E1 interface in slot 1 and unit 0. Specify the framing type. Specify the line code format. mapped. For multiflex trunk interfaces, only channel 0 can be configured. Configure each channel group as a virtual serial interface. Specify the E1 interface, unit number, and channel group to modify. Assign an IP address and subnet mask to the interface. Configure routing protocols on the interface. You must have previously enabled these protocols as part of global configuration. In this example, AppleTalk and IPX are being configured on the interface. Exit back to global configuration mode. Return to Step 4 if your router has more than one CE1/PRI interface that you need to configure.

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# controller e1 1/0

Step 5 Router(config-controller)# framing crc4 Step 6 Router(config-controller)# linecode hdb3

timeslots 1,3-5,7

Step 7 Router(config-controller)# channel-group 0 Specify the channel group and time slots to be

Step 8 Router(config-controller)# interface

serial 1/0:0

Step 9 Router(config-if)# ip address 10.1.15.1

255.255.255.0

Step 10 Router(config-if)# appletalk static

cable-range 3-3 Router(config-if)# appletalk zone ZZEth Router(config-if)# ipx network B005

Step 11 Router(config-if)# exit

Step 12 Router(config)# Ctrl-z

When you finish configuring interfaces, return to enable mode.

Configuring TDM Connect (Data Pass-Through)

For multiflex trunk interfaces using the time-division multiplexing (TDM) connect function, you can use the connect command to connect two groups of DS0 timeslots from two controllers.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-16

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring T1 and E1 Interfaces

To configure TDM connect, complete the following steps in controller configuration mode: Command
Step 1 To configure a TDM channel group for T1: a
Router(config-controller)# tdm-group tdm-group-no timeslot timeslot-list [type {e&m | fxs [loop-start | ground-start] | fxo [loop-start | ground-start]}]

Purpose Configure a TDM channel group for T1. If configuring cross-connect for data traffic only, do not specify the type option. The type option only applies if the mode cas command is enabled.

To configure a TDM channel gorup for E1:

b
Router(config-controller)# tdm-group tdm-group-no timeslot timeslot-list [type {e&m | fxs [loop-start | ground-start] | fxo [loop-start | ground-start] | fxs-melcas | fxo-melcas | e&m-melcas}]

Configure a TDM channel group for E1. The melcas options are supported only on E1 and apply to the Mercury Exchange Limited (MEL) Channel Associated Signaling (CAS) standard, used primarily in the United Kingdom. The MEL options help preserve CAS integrity on the line. If configuring cross-connect for data traffic only, do not specify the type option. The type option only applies if the mode cas command is enabled. Exit controller configuration mode. Configure cross-connect pass-through between two controllers.

Step 2 Router(config-controller)# exit Step 3 Router(config)# connect id controller-1

tdm-group-no-1 controller-2 tdm-group-no-2

Configuring Codec Complexity

The number of channels that an HDV network module can support depends on the number of PVDMs that are installed and the complexity level of the codecs (vocoders) needed to support the required compression method. The HDV network module supports the following number of channels:

Up to 6 channels per PVDM (up to 30 channels for cards with 5 PVDMs installed) for high complexity codecs (vocoders) that support the following services: G.711, G.726, G.729, G.723.1, G.728, and fax relay Up to 12 channels per PVDM (up to 60 channels for cards with 5 PVDMs installed) for medium complexity codecs (vocoders) that support the following services: G.711, G.726, G.729a, and fax relay

Each HDV network module can support only one type of compression complexity (either high or medium), although HDV network modules with different compression complexity types can be installed in the same router. Use the following procedure to configure the codec (vocoder) complexity on your HDV network module.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-17

Chapter 3 Configuring T1 (FT1) WAN Interface Cards

Configuring with the Command-Line Interface

Command
Step 1 Router> enable
Password: password Router#

Purpose Enter enable mode. Enter the password. You have entered enable mode when the prompt changes to Router#. Enter global configuration mode. You have entered global configuration mode when the prompt changes to Router(config)#. Select the voice card to configure. card.One complexity type is allowed per router. Exit back to global configuration mode. Return to Step 3 if your router has more than one voice card that you need to configure.

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router(config)# voice-card {0-4}

{high |medium}

Step 4 Router(config-voicecard)# codec complexity Specify the compression complexity for the voice Step 5 Router(config-voicecard)# exit

Step 6 Router(config)# Ctrl-z

When you finish configuring interfaces, return to enable mode.

Configuring T1 (FT1) WAN Interface Cards

The 1-port T1 and fractional (FT1) WAN interface card includes an integrated data service unit/channel service unit (DSU/CSU) and can be configured either for full T1 service at 1.544 Mbps or for fractionalized T1 service. You can configure the interfaces on your T1 WAN interface card manually by entering Cisco IOS commands on the command line. This method, called configuration mode, provides the greatest power and flexibility.

Timesaver

Connect a console to the router. Power on the router.

Default Configuration
The Cisco IOS software provides the following default configuration for CSU/DSU- and T1-specific parameters:
service-module service-module service-module service-module t1 t1 t1 t1 clock source line data-coding normal timeslots all speed 64 framing esf

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-18

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring T1 (FT1) WAN Interface Cards

service-module t1 service-module t1 no service-module service-module t1 no service-module

lbo none linecode b8zs t1 remote-alarm-enable remote-loopback t1 fdl

To change this configuration, enter commands in configuration mode, as described in the next section. To view the current configuration, enter the show service-module serial slot/port command. For further information about these commands, refer to the Cisco IOS configuration guides and command references. Command
Step 1 Router> enable
Password: password Router#

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# interface serial 0/0

Router(config-if)#

Step 5 Router(config-if)# ip address 172.16.74.2

255.255.255.0

Step 6 Router(config-if)# no keepalive

Router(config-if)# appletalk static cable-range 5-5 Router(config-if)# appletalk zone ZZ Router(config-if)# ipx network B004

Step 7 Router(config-if)# service-module t1

framing sf Router(config-if)# service-module t1 linecode ami

Step 8 Router(config-if)# service-module t1

timeslots 1-20 speed 64

If you are using fractional T1 service, enter the time slot range and speed. In this example, the time slot range specified is from 1 to 20, and the speed specified is 64 kbps. Exit back to global configuration mode. Repeat Step 4 through Step 8 if your router has more than one interface that you need to configure.

Step 9 Router(config-if)# exit

Step 10 Router(config)# Ctrl-z

Router#

When you finish configuring interfaces, return to enable mode.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-19

Chapter 3 Configuring ATM Interfaces

Configuring with the Command-Line Interface

Configuring ATM Interfaces

To configure an ATM interface, you must use configuration mode (manual configuration). In this mode, you enter Cisco IOS commands at the router prompt.
Note

Before you begin, disconnect all WAN cables from the router to keep it from trying to run the AutoInstall process. The router tries to run AutoInstall whenever you power it on if there is a WAN connection on both ends and the router does not have a valid configuration file stored in nonvolatile random-access memory (NVRAM) (for instance, when you add a new interface). It can take several minutes for the router to determine that AutoInstall is not connected to a remote Transmission Control Protocol/Internet Protocol (TCP/IP) host. This section describes basic configuration, including enabling the interface and specifying IP routing. Depending on your own requirements and the protocols you plan to route, you might also need to enter other configuration commands.

Configuring PVCs
To configure the ATM interface with PVCs, follow this procedure: Command
Step 1 Router> enable
Password: password Router#

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# interface atm 1/0

Router(config-if)#

Step 5 Router(config-if)# ip address 192.168.74.3 Assign an IP address and subnet mask to the
255.255.255.0

Step 6 Router(config-if)# appletalk static

cable-range 3-3 Router(config-if)# appletalk zone ZZEth Router(config-if)# ipx network B005

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-20

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring ATM Interfaces

Command
Step 7 Router(config-if)# pvc 0/100

Purpose Configure a new ATM PVC. Enter interface-ATM-VC configuration mode. The PVC command has the format pvc [name] vpi/vci [ilmi|qsaal] You have entered interface-ATM-VC configuration mode when the prompt changes to
Router(config-if-atm-vc).

Step 8 Router(config-if-atm-vc)# protocol ip

200.200.200.2 broadcast

Map the PVC to an address. Exit back to global configuration mode. Repeat Step 4 through Step 8 if your router has more than one interface that you need to configure.

Step 9 Router(config-if-atm-vc)# exit

Step 10 Router(config)# Ctrl-z

When you finish configuring interfaces, return to enable mode.

Configuring SVCs
To configure the ATM interface with switched virtual circuits (SVCs), follow this procedure: Command
Step 1 Router> enable
Password: password Router#

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# interface atm 1/0

Router(config-if)#

Step 5 Router(config-if)# pvc 0/5 qsaal Step 6 Router(config-if-atm-vc)# exit Step 7 Router(config-if)# pvc 0/6 ilmi Step 8 Router(config-if-atm-vc)# exit Step 9 Router(config-if)# ip address 192.168.74.3 255.255.255.0

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-21

Chapter 3 Configuring Inverse Multiplexing for ATM Interfaces

Configuring with the Command-Line Interface

Command
Step 10 Router(config-if)# appletalk static
cable-range 3-3 Router(config-if)# appletalk zone ZZEth Router(config-if)# ipx network B005

Purpose Configure routing protocols on the interface. You must have previously enabled these protocols as part of global configuration. In this example, AppleTalk and IPX are being configured on the interface. Configure the signaling PVC and the ATM network service access point (NSAP) address. The signaling PVC command has the format svc [name] nasp <20-byte address>. You have entered interface-ATM-VC configuration mode when the prompt changes to
Router(config-if-atm-vc).

Step 11 Router(config-if)# svc nsap

BC.CDEF.01.234567.890A.BCDE.F012.3456.7890 . 1234.12

Step 12 Router(config-if-atm-vc)# protocol ip 200.200.200.2 broadcast Step 13 Router(config-if-atm-vc)# exit

Map the PVC to an address. Exit back to global configuration mode. Repeat Step 4 through Step 12 if your router has more than one interface that you need to configure.

Step 14 Router(config)# Ctrl-z

When you finish configuring interfaces, return to enable mode.

Configuring Inverse Multiplexing for ATM Interfaces

To configure an inverse multiplexing for ATM (IMA) interface, you must use configuration mode (manual configuration). In this mode, you enter Cisco IOS commands at the router prompt.
Note

Before you begin, disconnect all WAN cables from the router to keep it from trying to run the AutoInstall process. The router tries to run AutoInstall whenever you power it on, if there is a WAN connection on both ends and the router does not have a valid configuration file stored in nonvolatile random-access memory (NVRAM) (for instance, when you add a new interface). It can take several minutes for the router to determine that AutoInstall is not connected to a remote Transmission Control Protocol/Internet Protocol (TCP/IP) host. This section describes basic configuration, including enabling the interface and specifying IP routing. Depending on your own requirements and the protocols you plan to route, you might also need to enter other configuration commands.

Note

The T1/E1 physical layer information is configured underneath an interface called

interface atm.

The ATM interfaces (representing the individual T1/E1 interfaces) are automatically created depending on the configuration of the individual T1/E1 interfaces. You cannot directly add or delete these interfaces. Each port can be used as an independent T1/E1 ATM port with all the properties and functionality of ATM interfaces. When the port becomes part of an IMA group, its ATM functionality ceases. At the same time, the IMA group can use ATM commands.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-22

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring Inverse Multiplexing for ATM Interfaces

Note

On the 8-port E1 or T1 network module, only four ATM layer interfaces can be operational at the same time. All the interfaces can be activated (configured as no shutdown) but only four at a time can be operational and pass network traffic.

Configuring the ATM T1/E1 Interface

To configure the ATM interface, follow this procedure: Command
Step 1 Router> enable
Password: password Router#

Purpose Enter enable mode. Enter the password. You have entered enable mode when the prompt changes to Router#. Enter global configuration mode. You have entered global configuration mode when the prompt changes to Router(config)#. Enable routing protocols as required for your global configuration. This example uses IP routing, AppleTalk routing, and Internetwork Packet Exchange (IPX) routing. Enter interface configuration mode. You have entered interface configuration mode when the prompt changes to Router(config-if)#. Enter the transmit clock mode for the selected ATM interface. The choices are internal, line, or loop. The default is line. For T1 interfaces only, specify the cable length (short or long) followed by the length in feet. You can view the acceptable cable lengths by including the ? option after the long or short commands. Specify the loopback type for this ATM interface by entering the loopback command followed by one of the following: line, local, payload, remote. You can view command descriptions by including the ? option after the loopback command .

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# interface atm 1/0

Router(config-if)#

Step 5 Router(config-if)# ima clock line

Step 6 Router(config-if)# cablelength short 133

Step 7 Router(config-if)# loopback local

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-23

Chapter 3 Configuring Inverse Multiplexing for ATM Interfaces

Configuring with the Command-Line Interface

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Enable routing protocols as required for your global configuration. This example uses IP routing, AppleTalk routing, and Internetwork Packet Exchange (IPX) routing. Enter interface configuration mode. You have entered interface configuration mode when the prompt changes to Router(config-if)#. Enter the transmit clock mode for the selected ATM interface. The choices are internal, line, or loop. The default is line. For T1 interfaces only, specify the cable length (short or long) followed by the length in feet. You can view the acceptable cable lengths by including the ? option after the long or short commands. Specify the loopback type for this ATM interface by entering the loopback command followed by one of the following: line, local, payload, remote. You can view command descriptions by including the ? option after the loopback command .

Step 4 Router(config)# interface atm 1/0

Router(config-if)#

Step 5 Router(config-if)# ima clock line

Step 6 Router(config-if)# cablelength short 133

Step 7 Router(config-if)# loopback local

Configuring the IMA Interface

To configure the IMA interface, follow this procedure:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-24

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring Inverse Multiplexing for ATM Interfaces

Command
Step 1 Router> enable
Password: password Router#

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# interface atm 1/0

Router(config-if)#

Step 5 Router(config-if)# ima-group 2

Step 6 Router(config-if)# no shutdown

The no shutdown command at this point activates the individual ATM link. If this command is omitted, the ATM link is added to the group but is inhibited at the IMA protocol level. This would prevent it from carrying network traffic.

Repeat Step 4 through Step 6 if your router has more than one interface that you need to configure.
Step 7 Router(config-if)# interface atm2/ima3

Create the IMA group interface.

Note

The group interface is deleted with the no interface atm 2/ima 3 command.

Step 8 Router(config-if)# ima clock-mode common

Select the transmit clock mode for the selected IMA group. The choices are common or independent. Enter the maximum differential delay in milliseconds for the selected IMA group. Enter the minimum number of links that need to be operational for the selected IMA group. Select the test port for the selected IMA group. The link number is one of the physcial ports on the network module. Assign an IP address and subnet mask to the interface.

Step 9 Router(config-if)# ima

differential-delay-maximum 75

Step 10 Router(config-if)# ima active-links-minimum

Step 11 Router(config-if)# ima test link 4

Step 12 Router(config-if)# ip address 192.168.74.3

255.255.255.0

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-25

Chapter 3 Configuring Analog Modem Interfaces

Configuring with the Command-Line Interface

Command
Step 13 Router(config-if)# appletalk static
cable-range 3-3 Router(config-if)# appletalk zone ZZEth Router(config-if)# ipx network B005

Purpose Configure routing protocols on the interface. You must have previously enabled these protocols as part of global configuration. In this example, AppleTalk and IPX are being configured on the interface. Enable the IMA group by canceling the shutdown state. When you finish configuring interfaces, return to enable mode.

Step 14 Router(config-if)# no shutdown Step 15 Router(config-if)# Ctrl-z

Router#

Checking the IMA Configuration

After configuring the new IMA interface, you can perform the following tests to verify that the new interface is operating correctly:

Enter the show ima interface atm1/3 command to verify information for the specified IMA group. Enter the show controllers atm0/ima2 command to display IMA diagnostic information for the specified group.

If an interface is down and you configured it as up, or if the displays indicate that the hardware is not functioning properly, make sure that the new interface is properly connected and configured.

Configuring Analog Modem Interfaces

To configure an analog modem interface, use the configuration software provided with your router or modem network module, if any. Otherwise, use configuration mode (manual configuration). In this mode, you enter Cisco IOS commands at the router prompt.
Note

Note

This section does not describe modem AT commands. For information about these commands, see the AT Command Set and Register Summary for Analog Modem Network Modules publication on Cisco.com, or Documentation CD-ROM. Before you begin configuring the interfaces, make sure you:

Connect a console to the router. Power on the router.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-26

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring Analog Modem Interfaces

Command
Step 1 Router> enable
Password: password Router#

Purpose Enter enable mode. Enter the password. You have entered enable mode when the prompt changes to Router#. Enter global configuration mode. You have entered global configuration mode when the prompt changes to Router(config)#. Enable routing protocols as required for your global configuration. This example uses IP routing, AppleTalk routing, and Internetwork Packet Exchange (IPX) routing. You can configure asynchronous interfaces either individually or as a group. This command selects an individual interface to configure. The prompt changes to Router(config-if)#. Assign an IP address and subnet mask to the interface. Assign asynchronous interfaces to a group so you can configure them together. Configure the asynchronous interface group as unnumbered and assign the IP address of the Ethernet interface to the group. Define the pool of addresses at the global level. Define the group range of the interface. This command defines the range as all modems in slot 0. Configure routing protocols on the interface or group. You must have previously enabled these protocols as part of global configuration. In this example, AppleTalk and IPX are being configured on the interface. Configure asynchronous parameters according to your needs.

Step 2 Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z. Router(config)#

Step 3 Router# ip routing

Router# appletalk routing Router# ipx routing

Step 4 Router(config)# interface async 45

Router(config-if)#

Step 5 Router(config-if)# ip address 172.16.74.1

255.255.255.0

Step 6 Router(config)# interface group-async 1 Step 7 Router(config-if)# ip unnumbered ethernet 0

Step 8 Router(config-if)# peer default ip address

pool default

Step 9 Router(config-if)# group-range 1 16

Step 10 Router(config-if)# appletalk static

cable-range 3-3 Router(config-if)# appletalk zone ZZEth Router(config-if)# ipx network B005

Step 11 Router(config-if)# async mode interactive

Router(config-if)# async default routing Router(config-if)# encapsulation ppp Router(config-if)# ppp authentication chap pap

Step 12 Router(config-if)# exit

Exit back to global configuration mode. Return to Step 4 if your router has more than one interface that you need to configure.

Step 13 Router(config)# modem country microcom_hdms

country-name

Set modem parameters (including encoding) to the correct country. Table 3-8 shows country codes. The default is usa. Enter the modem line or range of modem lines to configure.

Step 14 Router(config-if)# line 1 16

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-27

Chapter 3 Configuring Wireless Multipoint Interfaces

Configuring with the Command-Line Interface

Command
Step 15 Router(config-line)# transport input all Step 16 Router(config-line)# autoselect ppp

Purpose Allow all protocols to be used when connecting to the line. Enable remote IP users running a PPP application to dial in, bypass the EXEC facility, and connect directly to the network. Enable incoming and outgoing calls. When you finish configuring interfaces, return to enable mode.

Step 17 Router(config-line)# modem inout Step 18 Router(config-if)# Ctrl-z

Table 3-8

Modem Country Codes

Country Codes
argentina australia austria belgium brazil canada chile china columbia czech-republic Denmark Finland France Germany Greece hong-kong hungary india indonesia ireland israel italy japan korea malaysia mexico netherlands new-zealand norway peru philippines poland portugal saudi-arabia singapore south-africa spain sweden switzerland taiwan thailand united-kingdom usa

Checking the Modem Configuration

After configuring the new modem interface, you can perform the following tests to verify that the new interface is operating correctly:

To verify your group interface configuration, enter the show interface async command. To display a summary for all modem lines, enter the show line command. To display a summary for a single modem line, enter the show line number command.

If an interface is down and you configured it as up, or if the displays indicate that the hardware is not functioning properly, make sure that the new interface is properly connected and configured.

Configuring Wireless Multipoint Interfaces

The configuration process for the fixed wireless multipoint subscriber-unit is automated. For information about the following optional configuration tasks, see the Multipoint Wireless Support for the Cisco 2600 and Cisco 3600 Series Routers feature module:

Specifying an alternative boot location Configuring cable loss

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-28

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Checking the Interface Configuration

Configuring RF loopback

Checking the Interface Configuration

After configuring the new interface, you can perform the following tests to verify that the new interface is operating correctly:

Display the router hardware configuration with the show version command. Check that the list includes the new interface. Display all network modules and their interfaces with the show controllers command. Specify an interface with the show interfaces [type slot/port] command and verify that the first line of the display shows the interface with the correct slot and port number, and that the interface and line protocol are in the correct state, up or down. Display the protocols configured for the entire router and for individual interfaces with the show protocols command. If necessary, return to configuration mode to add or remove protocol routing on the router or its interfaces. Display the running configuration with the show running-config command, and the configuration stored in NVRAM using the show startup-config command. Use the ping command to send an echo request to a specified IP address. Each returned signal is displayed as an exclamation point (!) on the console; each signal that is not returned before the timeout is displayed as a period (.). A series of exclamation points (!!!!!) indicates a good connection; a series of periods (.....) or the message timed out or failed indicate that the connection failed.

If an interface is down and you configured it as up, or if the displays indicate that the hardware is not functioning properly, make sure that the new interface is properly connected and configured.

Configuring 1-Port ADSL WAN Interface Card

The ADSL WAN interface card is a 1-port WAN interface card (WIC) for the Cisco 2600 series and Cisco 3600 series routers. The card provides asymmetric digital subscriber line (ADSL) high-speed digital data transfer between a single customer premises equipment (CPE) subscriber and the central office. The ADSL WIC is compatible with the Alcatel Digital Subscriber Loop Access Multiplexer (DSLAM) and the Cisco 6130, Cisco 6160, and Cisco 6260 DSLAMs with Flexi-line cards. It supports Asynchronous Transfer Mode (ATM) Adaptation Layer 2 (AAL2) and AAL5 for the Cisco 2600 series and Cisco 3600 series platforms for both voice and data service. The general topology is shown in Figure 3-1.
Figure 3-1 General Topology for ADSL WIC

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-29

Chapter 3 Configuring 1-Port ADSL WAN Interface Card

Configuring with the Command-Line Interface

Note

ADSL is a last-mile access technology, which has an asymmetrical data rate running over a single copper wire pair.

Benefits

Enables business class broadband service with voice integration, scalable performance, flexibility, and security. Aggregates both ADSL and other transport options into a single box. Provides both POTS and ADSL high-speed digital data transmissions between the customer premises equipment (CPE) and the central office (CO). Supports ITU G.992.1 (or G.DMT, which specifies full-rate ADSL). Supports and complies with ANSI T1.413 issue 2, and ITU G.992.1 (G.DMT for full-rate ADSL). Supports ATM AAL2 and AAL5 services on the Cisco 2600 series and Cisco 3600 series platforms. Supports applications (including VoATM voice), ATM class of service, variable bit rate-nonreal time [VBR-NRT], variable bit rate-real time [VBR-rt], and unspecified bit rate [UBR]) and up to 23 virtual circuits on a WIC. Provides ATM traffic management to enable service providers to manage their core ATM network infrastructures.

Restrictions

The ADSL WAN interface card does not support dual latency. When the ADSL link is intended to support both voice and data traffic simultaneously, the link should be configured for either all fast-path data or all interleave data with an interleave depth of zero to insure that latency is minimized. In addition, the total supported data rate must be reduced to adjust for the reduced coding gain, which is usually present with high-latency traffic. The ADSL WAN interface card does not support available bit rate (ABR) class of service (CoS). For the Cisco 2600 series routers, the ADSL WAN interface card should be inserted only into on-board WIC slots or 2W network modules. This card does not function properly in older network modules. For the Cisco 3600 series routers, the ADSL WAN interface card should be inserted only into onboard WIC slots or 2W, 1FE2W, 2FE2W, or 1FE1R2W network modules. This card does not function properly in older network modules. When using AAL2, analog voice is not supported. Voice calls should come through a digital voice card, such as the NM-HDV. VoATM is supported in both AAL2 and AAL5 modes on the Cisco 2600 series and Cisco 3600 series routers. VoATM AAL2 and AAL5 are supported only if voice and data use separate permanent virtual circuits (PVCs). VoATM AAL2 supports digital voice (T1/E1) only, while VoATM AAL5 supports both analog and digital voice. VoIP is not supported unless the ADSL WIC carries only voice traffic (with no data). The QoS features necessary for VoIP and data sharing the same PVC, or different PVCs on the same interface, are not supported yet. These features include LLQ, LFI, and tx-ring tuning.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-30

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring 1-Port ADSL WAN Interface Card

Prerequisites
A 1-Port ADSL WIC must be installed in the router to match the DSL service to be configured.

Configuration Tasks
See the following sections for configuration tasks for this feature. Each task in the list is identified as either required or optional:

Configuring the ADSL Port on the ADSL WAN Interface Card (required) Verifying ATM Configuration (optional)

Features used on the ADSL WAN interface card must also be configured on the DSLAM. See the documentation for the specific DSLAM for information about configuring features.

Configuring the ADSL Port on the ADSL WAN Interface Card

To configure an ADSL port on the ADSL WAN interface card, complete the following steps: Command
Step 1 Step 2 Step 3 Step 4
Router> configure terminal Router(config)# interface atm slot/port Router(config-if)# ip address IP-address Router(config-if)# pvc [name] vpi/vci

Purpose Enter global configuration mode. Enter ATM configuration mode for the ATM interface in the specified slot and port. Assign an IP address to the ADSL ATM interface. Entes atm-virtual-circuit (interface-atm-vc) configuration mode, and configures a new ATM PVC by assigning a name (optional) and virtual path identifier (VPI)/virtual channel identifier (VCI) numbers. The default traffic shaping is UBR; the default encapsulation is AAL5+LLC/SNAP.

Step 5 Step 6

Router(config-if-vc)# protocol ip IP-address Router(config-if-vc)# vbr-rt peak-rate average-rate burst

(Optional) Enable IP connectivity and create a point-to-point IP address for the virtual circuit (VC). (Optional) Configure the PVC for real-time variable bit rate (VBR) traffic shaping.

peak ratePeak information rate (PIR) average rateAverage information rate (AIR) burstBurst size in cells

Step 7

Router(config-if-vc)# encapsulation {aal2 | aal5ciscoppp | aal5mux | aal5nlpid | aal5snap}

(Optional) Configure the ATM adaptation layer (AAL) and encapsulation type.

aal2AAL2 aal5ciscopppCisco PPP over AAL5 aal5muxAAL5+MUX aal5nlpidAAL5+NLPID aal5snapAAL5+LLC/SNAP (the default)

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-31

Chapter 3 Configuring 1-Port ADSL WAN Interface Card

Configuring with the Command-Line Interface

Command
Step 8 Step 9
Router(config-if-vc)# exit Router(config-if)# dsl operating-mode {ansi-dmt | auto | itu-dmt | splitterless}

Purpose Exit from interface-atm-vc configuration mode. Configure the ADSL interface to operate in a specified mode:

ansi-dmtANSI full rate mode per T1.413 (ITU G.DMT Issue 1) autoAutomatic detection mode itu-dmtITU full rate mode (ITU G.DMT Issue 1) splitterlessG.lite mode per ITU G.992.2

Caution

This command is for testing or lab environments only. Using a configuration other than the default configuration for the DSL operating mode can lead to unpredictable behavior on the ADSL line.

Step 10 Step 11 Step 12 Step 13

Router(config-if)# no shutdown Router(config-if)# exit Router(config)# exit Router# show interface atm 1/0

Activate the ATM interface. Exit from ATM interface configuration mode. Exit from global configuration mode. Verify the ATM interface configuration.

Verifying ATM Configuration

Use the following commands to verify configuration:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-32

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring 1-Port ADSL WAN Interface Card

Encapsulation(s):AAL5 AAL2, PVC mode 24 maximum active VCs, 256 VCs per VP, 2 current VCCs VC idle disconnect time:300 seconds Last input never, output 00:00:01, output hang never Last clearing of "show interface" counters 03:16:00 Queueing strategy:fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 30 second input rate 0 bits/sec, 0 packets/sec 30 second output rate 0 bits/sec, 0 packets/sec 2527 packets input, 57116 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 10798 packets output, 892801 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out

Router# show atm vc VCD / Interface 1/0.3 1/0.2 Peak Encaps MUX SNAP Avg/Min Burst SC Kbps Kbps UBR 800 UBR 800

Name 2 1

VPI 9 9

VCI 36 37

Type PVC PVC

Cells

Sts UP UP

Router# show controllers atm 1/0 Interface ATM1/0 is up Hardware is DSLSAR (with Alcatel ADSL Module) IDB: 62586758 Instance:6258E054 reg_dslsar:3C810000 wic_regs:3C810080 PHY Inst:62588490 Ser0Inst:62573074 Ser1Inst: 6257CBD8 us_bwidth:800 Slot: 1 Unit: 1 Subunit: 0 pkt Size:4496 VCperVP:256 max_vp: 256 max_vc: 65536 total vc:2 rct_size:65536 vpivcibit:16 connTblVCI:8 vpi_bits:8 vpvc_sel:3 enabled: 0 throttled:0 WIC Register --------------FPGA Dev ID (LB) FPGA Dev ID (UB) FPGA Revision WIC Config Reg Value ---------0x44 0x53 0x99 0x45 Notes ---------'D' 'S' WIC / VIC select = WIC; CTRLE addr bit 8 = 1; OK LED on; LOOPBACK LED off; CD LED on; Gen bus error on bad ADSL access ADSL normal interrupt enabled ADSL error interrupt enabled

WIC Config Reg2 Int 0 Enable Reg

0x07 0x03

Configuration Examples
Examples of the following configurations are described in Appendix A, Configuration Examples,on page A-1:

VoATM over AAL2 on the ATM Interface Configuration Example, page A-12 VoATM over AAL5 on the ATM Interface Configuration Example, page A-14

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-33

Chapter 3 Configuring the NM-AIC-64, Contact Closure Network Module

Configuring with the Command-Line Interface

Configuring the NM-AIC-64, Contact Closure Network Module

The Alarm Interface Card Network Module (AICNM) is an optional card that expands network management capabilities for customer-defined alarms. The AIC has its own CPU that communicates with the router and external media through serial communication channels. The AIC reduces service provider and enterprise operating costs by providing a flexible, low-cost network solution for migrating existing data communications networks (DCNs) to IP-based DCNs. The AIC provides its users with a single box solution because it can be configured in the same router along with other operation, alarm, maintenance, and provisioning (OAMP) interfaces. More than one AIC can be installed per router. For example, a Cisco 3662 can have up to five AICs, and its sixth NM slot can be used for router communication. The Cisco 3640 can have up to three AICs, with the fourth NM slot reserved for communication, and so forth. The AIC provides a total of 64 alarm inputs. Eight of the 64 point are software configurable for measuring either analog inputs or discrete inputs. The remaining 56 points are fixed to measure discrete points only. The AIC also provides 16 control relay outputs. The discrete alarm input can be activated through ground or negative battery input. The negative battery range is -36V to -72V. The analog alarm is software configurable for either DC voltage or current. It can measure voltage from -60 to 60V or current from 0 to 20mA, but the configurable range is 4 mA to 20mA. The standard 16 control relays can be configured to turn on or turn off an external device. The AICs 64 input contact points can control and monitor network elements and other non-intelligent interfaces, permitting the detection and report of alarms such as the following:

Network element alarm states Building security (door and window open and close) Fire and smoke indication Building environmentals (temperature and humidity) Utility power readings

When an event occurs, such as a door alarm or an open gate, the AIC maps the simple discrete and analog alarms to preprogrammed intelligent messages and transports the messages to destinations in the IP network, typically to a Network Operations Center (NOC). These messages are generated either in Transaction Language 1 (TL1) or in Simple Network Management Protocol (SNMP), which are used by a NOCs Operations Support System (OSS). When the AIC is incorporated into the Cisco DCN solution platforms, all the AICs contact-closure alarms are routed and reported through the same network and systems as the intelligent network elements (NEs). This facilitates continued use of the existing OSS and its associated networks. A Cisco router with an AIC sends TL1 or SNMP messages to the OSS autonomously or in response to TL1 or SNMP commands from the OSS, as shown in Figure 3-2. TL1 supports two sessions, with the port numbers 5011 and 5012, respectively, and SNMP supports four sessions.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-34

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the NM-AIC-64, Contact Closure Network Module

Figure 3-2

TL1 and SNMP Message Flow in a DCN Application

Serial Communication Channels

As illustrated in Figure 3-3, the AIC has two serial communications channels that provide different types of interfaces to Cisco IOS software:

Serial data channel Asynchronous craft port

OS Boundary into the AIC

Figure 3-3

Serial Data Channel

The serial data channel supports all TCP/IP traffic to and from the AIC. This includes communication over IP with NOCs and data centers. The channel consists of one physical interface that provides support for the following applications:

Telnet TL1 TFTP

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-35

Chapter 3 Configuring the NM-AIC-64, Contact Closure Network Module

Configuring with the Command-Line Interface

SNMP

The Cisco IOS software assigns an IP address to the AIC for use by the serial data channel. To route traffic, the serial data channel uses IP over synchronous High-Level Data Link Control (HDLC). All IP packets coming to the Cisco router with a destination IP address that matches the AICs IP address are forwarded to the serial data channel using IP over HDLC.

Asynchronous Craft Port

The asynchronous craft port supports Telnet to the AICs port number. This Telnet method, called local-CLI, is useful for debugging when remote Telnet to the AICs IP address (remote-CLI) is not applicable. For more information, see the Configuring the NOC IP Address section on page 3-40. The asynchronous craft port also supports an AIC boot sequence, similar to the ROM monitor in Cisco IOS software, which allows the user to recover from a corrupted software image or configuration. See the Override section on page 3-46.

Configuring the AIC

From a top-level view, AIC configuration involves assigning an IP address to the AIC using Cisco IOS commands and setting up alarm configurations with either TL1 or the AIC command-line interface (CLI). The flexible TL1 and AIC CLI permit a broad range of alarm configuration scenarios. The following are examplesof alarm configurations that can be programmed with the AIC CLI:

Configuring a Discrete Alarm

enable config terminal alarm 1 description "west door" normally closed description normal "door closed" description alarm "door open" level 2 exit

Configuring an Analog Alarm as an Analog Monitoring Voltage

enable config terminal alarm 57 description "tank level" description normal "full" description low "low" description low-low "empty" analog voltage 2.5 30 60 60 exit

Configuring an Analog Alarm as a Discrete Monitoring Current

enable config terminal alarm 58 description "east door" discrete current-loop 0.0 3.2 5.9

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-36

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the NM-AIC-64, Contact Closure Network Module

exit

Configuring an Analog Alarm as a Discrete Monitoring Voltage

enable config terminal alarm 58 description "backup battery" discrete voltage 9.0 high exit

Configuring an Analog Alarm to Act Like a Discrete Alarm (Minimal Configuration Method)
enable config terminal alarm 59 discrete exit

Configuration Tasks
See the following sections for configuration tasks for the AIC feature. Each task in the list is identified as either required or optional:

Configuring the AIC, page 3-37 (required)

Entering Alarm Configuration Mode and Configuring the AIC IP Address, page 3-37 Configuring the IP Route to the AIC, page 3-38

Configuring the NOC IP Address, page 3-40 (optional) Configuring Alarms, page 3-41 (optional)

Configuring the AIC

Cisco IOS commands are used for configuring the AIC IP address and the IP routing to the AIC NM. After the IP address and the IP routing are set, alarm configurations can then be set up with either TL1 or the AIC command-line interface. See theConfiguring the NOC IP Address section on page 3-40 or the Configuring Alarms section on page 3-41 for more information. The following sections describe how to configure the AIC IP address and the IP Routing to the AIC NM.

Entering Alarm Configuration Mode and Configuring the AIC IP Address

Enter alarm configuration mode and configure the AIC IP address, beginning in privileged EXEC mode:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-37

Chapter 3 Configuring the NM-AIC-64, Contact Closure Network Module

Configuring with the Command-Line Interface

Table 3-9

Configuring IP Routing to the AIC with an Unnumbered IP Address

Command
Step 1
Router# show run

Purpose Determines if the AIC is installed correctly in the router. If the AIC has been installed correctly, then the following appears:
interface serialslot/port

where the slot is the slot in which the AIC is inserted, and the port is 0.
Step 2 Step 3 Step 4
Router# configure terminal Router(config)# alarm-interface slot

Starts the configuration session. Enters the AIC interface mode, specifying the slot number into which the AIC is installed. Enters the IP address of the AIC. Entering a mask is optional, because the IP address does not use a subnet address. Resets the AIC. Changing the IP configuration may not take until the next time the card is started. The reset command restarts the card. Exits the AIC interface mode.

Router(config-aic)# ip address ip-address mask

Step 5

Router(config-aic)# reset

Step 6

Router(config-aic)# exit

Configuring the IP Route to the AIC

There are many ways to configure IP routing to the AIC. Below are two methods. The first method, shown in Table 3-10, uses an unnumbered IP address. It is used when an administrator wants to assign an IP address that is already known to the router, such as an address that is one of the addresses in the subnet of a FastEthernet IP address. The second method, shown in Table 3-11, does not use an unnumbered IP address and is used when there is a subnet available to the serial interface and to the AIC. Usually this subnet is small with a subnet mask such as 255.255.255.252. Configure IP routing to the AIC, beginning in global configuration mode:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-38

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the NM-AIC-64, Contact Closure Network Module

Table 3-10 Configuring IP Routing to the AIC with an Unnumbered IP Address

Command
Step 1
Router(config)# ip route network-number network-mask {IP address | interface} [distance] [name name]

Purpose Establish the discrete IP route and mask on the routers serial interface. The arguments have the following meanings: network-numberIP address of the target network or subnet. network-maskNetwork mask that lets you mask network and subnetwork bits. IP addressInternet address of the next hop that can be used to reach that network in standard IP address notation. Example: 10.1.1.1. interfaceNetwork interface to use. distance(Optional) An administrative distance, which is a rating of the trustworthiness of a routing information source, such as an individual router or a group of routers. name name(Optional) Name of the user profile. Example:
Router(config)#ip route 10.5.5.2 255.255.255.255 serial2/0

Step 2 Step 3

Router(config)# interface serialslot/port

Enter serial interface mode. Enter the slot in which the AIC is installed and port 0. Enable IP processing on the serial interface to the AIC without assigning an explicit IP address to the interface. The type and interface-number arguments indicate another interface on which the router has an assigned IP address. The other interface cannot be an unnumbered interface, because only an interface that has its own IP address can be used to lend its IP to the serial port. Enter, for example:
Router(config-if)# ip unnumbered FastEthernet 0/0

Router(config-if)# ip unnumbered type interface-number

Step 4

Router(config-if)# exit

Exit serial interface mode.

Table 3-11 Configuring IP Routing to the AIC without an Unnumbered IP Address

Command
Step 1 Step 2
Router(config)# interface serialslot/port

Purpose Enter the serial interface mode. Enter the slot in which the AIC is installed and the port 0. Specifie the IP address and mask of the routers serial interface to the AIC. For example:
Router(config)# ip route 10.5.5.1 255.255.255.0

Router(config-if)# ip address ip-address network-mask

Step 3

Router(config-if)# exit

Exits the serial interface mode.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-39

Chapter 3 Configuring the NM-AIC-64, Contact Closure Network Module

Configuring with the Command-Line Interface

Accessing the AIC

Remote-CLI and local-CLI are the two methods for accessing the AIC:

Remote-CLI involves telneting to the IP address of the AIC. For example:

telnet 10.5.5.2

Local-CLI involves accessing the asynchronous craft port by telneting to the IP address of the router and the AICs TCP port number. For example:
telnet 10.2.130.105 2001

where 10.2.130.105 is the routers IP address and 2001 is on slot 0 of the AIC. The AICs TCP port number depends on the slot number in which the AIC is installed. As shown in Table 3-12, the Cisco IOS software reserves the first line of each slot for the asynchronous craft port.
Table 3-12 TCP Port Number Allocation for the AIC on the Cisco 2600 and Cisco 3600 Series

Slot Number 0 1 2 3 4 5 6

Terminal Line Number for the AICs Asynchronous Craft Port 1 33 65 97 129 161 193

TCP Port Number 2001 2033 2065 2097 2129 2161 2193

Configuring the NOC IP Address

Configure up to four NOC IP addresses to which the AIC will send SNMP messages, beginning in global configuration mode:
Note

The aic command-line prompt indicates that either TL1 or AIC CLI commands must be used.

Command
Step 1 Step 2
aic(config)# snmp aic(config)# noc ip-address {number} ip-address

Purpose Enter SNMP configuration mode. Enter an NOC IP address in which the AIC will send SNMP messages. The number argument can be the numbers 1 through 4. Exit the AIC CLI.

Step 3

aic(config)# exit

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-40

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the NM-AIC-64, Contact Closure Network Module

Configuring Alarms
After the AIC and NOC IP addresses have been configured, you can the configure alarms by programming the AICs discrete and analog contact points. These tasks can be performed on-site or by Telneting as described in the Accessing the AIC section on page 3-40. Alarms are configured using either TL1 or AIC CLI. Information about TL1 commands can be found in the Telcordia Technology (formerly Bellcore) document Network Maintenance: Network Element and Transport Surveillance Messages, GR-833-CORE, Issue 5, November 1996. For a reference of security-related commands (ACT-USER and CANC-USER) refer to Telcordia Technologys Operations Applications Messages-Network Element and Network System Security Admin Messages, TR-NWT-000835, Issue 2, January 1993. The following TL1 messages and commands are supported by the AIC:

TL1 Messages
REPT-ALM-ENV REPT-ALM-EQPT REPT-EVT

TL1 Commands
ACT-USER CANC-USER OPR-EXT-CONT RLS-EXT-CONT RTRV-ALM RTRV-ALM-ENV RTRV-ATTR RTRV-ATTR-CONT RTRV-ATTR-ENV RTRV-ATTR-LOG RTRV-HDR RTRV-LOG RTRV-EXT-CONT SET-ATTR-ENV SET-ATTR-EQPT SET-ATTR-LOG STA-LOG STP-LOG

Programming the Analog Contact Points

Alarm points 57 through 64 are analog inputs, which are configurable as discrete inputs. When configured as an analog input, the user must select whether the point is monitoring voltage or current. The user must also define five ranges by selecting four values for a point monitoring voltage or six ranges for a point monitoring current. For current-monitoring points, the lowest and highest values

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-41

Chapter 3 Configuring the NM-AIC-64, Contact Closure Network Module

Configuring with the Command-Line Interface

define the range of possible values. (Valid values are from 9999999.9 to 9999999.9.) For voltage-monitoring alarms, the range of possible values is always 60V to 60V. The other four values must be within the defined range, and they partition the range into low-low, low, high, and high-high ranges. Except for the normal range, each range is associated with an alarm condition. Analog points have four unique alarm states. Each alarm state has its own alarm description string. Only one alarm state per point may be active at any given time. In other words, when a threshold is crossed, the previous alarm state is cleared and the new alarm state is active. When an analog input is configured as discrete, the user must select whether the point is monitoring voltage or current. Similar to the analog configuration, the user must also select the range of acceptable values for a current-monitoring alarm. (Valid values are from 9999999.9 to 9999999.9.) The voltage range is always 60V to 60V. The user must define the threshold that will cause the alarm condition and whether the normal state of the alarm is the higher or lower range.
Note

For the current analog point, the lower boundary is 4 mA and the upper boundary is 20 mA. For example,
analog current-loop 10 13 16 17 20 26

has 16 units between 10 and 26. If the AIC measures 4 mA, then it will factor that the point is registering at the lower boundary. The AIC will interpret 13 as 7 mA, 16 as 10 mA, 17 as 11 mA, 20 as 14 mA, and 26 as the upper boundary, which is 20 mA. Following are examples: Point 57 is monitoring the ambient temperature of a building and the sensor range is 20 to 75 degrees Celsius. Below 0 degrees is a critical alarm, 0 to 10 degrees is a major alarm, 10 to 35 degrees is the normal range, 35 to 45 degrees is a minor alarm, and above 45 degrees is a major alarm. The configuration for this point follows:
alarm 57 analog current-loop 20 0 10 35 45 75 level low-low 1 level low 2 level high 3 level high-high 2

Point 58 is monitoring a fuel tank level with a resistive sensor. Below 46 volts is a critical alarm, 46 to 40 volts is a minor alarm, and above 40 volts is the normal range. This is a unidirectional alarm, so the high thresholds are set equal to the high bound (since this threshold cannot be crossed). The configuration for this point follows:
alarm 58 analog voltage 46 40 60 60 level low-low 1 level low 3

Point 59 is monitoring a battery bank. Below 42 volts is a critical alarm and above 42 volts is the normal range. The configuration for this point follows:
alarm 59 discrete voltage 42 high level 1

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-42

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the NM-AIC-64, Contact Closure Network Module

Programming the Discrete Contact Points

The discrete alarms do not require as much programming as the analog alarms. The AIC CLI commands available are the following: Command no exit description normally Description Reversal option Exits current mode Sets the description. If no is set, then the description is not required. Sets the alarms normal state to closed. If the no option is used, the normal state is set to open. This command applies only to points 1 - 56. Sets the alarms level to the specified level.

level

Verifying the IP Address

To verify that the correct AIC IP address and IP route was entered, use the show run command. Below are samples of before-configuration and after-configuration show run command outputs:
interface Serial5/0 ip unnumbered FastEthernet0/0 ! ip route 10.2.130.102 255.255.255.255 Serial5/0 ! alarm-interface 5 ip address 10.2.130.102

********Before Configuration show run Output******* version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname uut2-3660 ! logging rate-limit console 10 except errors ! ip subnet-zero ! ! no ip finger no ip domain-lookup ! call rsvp-sync cns event-service server ! ! interface FastEthernet0/0 ip address 10.2.130.2 255.255.0.0 duplex auto speed auto no cdp enable

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-43

Chapter 3 Configuring the NM-AIC-64, Contact Closure Network Module

Configuring with the Command-Line Interface

! interface Serial5/0 no ip address ! ip kerberos source-interface any ip classless ip route 0.0.0.0 0.0.0.0 10.2.0.1 ip http server ! no cdp run ! ! dial-peer cor custom ! ! line con 0 exec-timeout 0 0 transport input none line 161 no exec transport preferred none transport input telnet transport output none stopbits 1 line aux 0 line vty 0 4 password lab login ! end

*****After Configuration show run Output******* version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname uut2-3660 ! logging rate-limit console 10 except errors no logging console ! ip subnet-zero

! !
no ip finger no ip domain-lookup ! call rsvp-sync cns event-service server ! interface FastEthernet0/0 ip address 10.2.130.2 255.255.0.0 duplex auto speed auto no cdp enable ! interface Serial5/0 ip unnumbered FastEthernet0/0 !

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-44

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the NM-AIC-64, Contact Closure Network Module

ip kerberos source-interface any ip classless ip route 0.0.0.0 0.0.0.0 10.2.0.1 ip route 10.2.130.102 255.255.255.255 Serial5/0 ip http server ! no cdp run ! ! alarm-interface 5 ip address 10.2.130.102 ! dial-peer cor custom ! ! ! line con 0 exec-timeout 0 0 transport input none line 161 no exec transport preferred none transport input telnet transport output none stopbits 1 line aux 0 line vty 0 4 password lab login ! end

Troubleshooting Tips
If no alarm messages are sent for an unusually long period of time, ping the AIC address to check for connectivity.

Monitoring and Maintaining the NM-AIC-64 Contact Closure Network Module

The AIC provides a TFTP client for software upgrade and configuration image transfer. The methods for both actions, as well as how to override the existing software or configuration, are described below.

Software Upgrade
When upgrading software, the AIC must be reset to run the new software. The AIC provides a protected (login required) command for software download. When the user invokes this command with the TFTP server address as a parameter, the AIC connects to the IP address and, via TFTP, retrieves the software image file. After verifying that the software has been transferred successfully, the AIC replaces its running software with the newly downloaded software. In the case of incompatible versions of Cisco IOS and AIC software, the Cisco IOS software recognizes the difference and displays this information to the user. The user makes the decision whether to upgrade or downgrade either the Cisco IOS or AIC software or to take no corrective action.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-45

Chapter 3 Configuring the 1-Port HSSI Network Module

Configuring with the Command-Line Interface

Configuration Backup
The AIC CLI provides commands for storing and restoring configurations. Users can transfer the current configuration of the AIC to or from the TFTP server whose address is given as a parameter to the get config command. When a configuration file is transferred from the server to the AIC, the AIC takes on the new configuration. The configuration is stored as a list of commands (script) that can be applied to the CLI of an AIC for configuration. Two other useful commands are the get image and put config commands. Use the get image command to get a new image, and the put config command to back up the configuration to the TFTP server. Backup is not automatic, but the AIC reminds the user, on logout, to back up the configuration.

Override
In the case that bad software is resident on the AIC or that the configured administrator password is lost, the AIC provides a method for recovering the card. Upon booting, the AIC begins a countdown, visible at the AIC local CLI (Craft Port). If an ASCII character is received on that local CLI channel (DSCC4 channel 2) during this countdown, the AIC enters a mode in which a limited CLI is available. At this limited CLI, available over the Craft Port only, no login is necessary. The user may enter commands for software upgrade and configuration transfer. The new configuration takes effect upon a reset of the AIC card. After interrupting the countdown, the user will see an AIC Boot]: prompt. From this prompt, the user can enter ? to see the available commands, g to get a new application image, or d to delete the current configuration and return to the defaults. (All commands require a carriage return.) In the case of the get command, the user will be prompted for the name of the file, the IP address of the TFTP server, and a confirmation.

Configuration Examples
The following configuration examples are shown in Appendix A, Configuration Examples:

AIC IP Address Configuration Example, page A-16 IP Route to the AIC Configuration Examples, page A-20
With an Unnumbered IP Address, page A-20 Without an Unnumbered IP Address, page A-21

Configuring the 1-Port HSSI Network Module

The Cisco 3600 series 1-port high-speed serial interface (HSSI) network module provides full-duplex connectivity at Synchronous Optical Network (SONET) OC-1/STS-1 (51.840 Mhz), T3 (44.736 MHz), and E3 (34.368 MHz) rates in conformance with the EIA/TIA-612 and EIA/TIA-613 specifications. The actual rate of the interface depends on the external data service unit (DSU) and the type of service to which it is connected. This 1-port HSSI network module can reach speeds of up to 52 Mbps in unidirectional traffic with 1,548-byte packets and 4,250 packets per second. Asynchronous Transfer Mode (ATM), High-Level Data Link Control (HDLC), Point-to-Point Protocol (PPP), Frame Relay, and Switched Multi-Megabit Data Service (SMDS) WAN services are all fully supported. The 1-port HSSI network module provides the following benefits:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-46

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the 1-Port HSSI Network Module

Supports speeds up to 52 Mbps Supports a range of connectivity options: ATM, Frame Relay, PPP, and SMDS Supports EIA/TIA-612 and EIA/TIA-613 specifications at T3, E3, SONET OC1/STS-1 and NXT1 subrates

Configuration Tasks
Perform the tasks in the following sections to configure a HSSI interface. The first task is required; the remaining tasks are optional.

Specify a HSSI, page 3-47 Specify HSSI Encapsulation, page 3-47 Invoke ATM on a HSSI Line, page 3-47 Convert HSSI to Clock Master, page 3-48 Disable Fair Queueing, page 3-48

Specify a HSSI
To specify a HSSI and enter interface configuration mode, perform the following tasks in global configuration mode: Task Begin interface configuration. Command
interface hssi slot/port

Specify HSSI Encapsulation

The HSSI supports the serial encapsulation methods, except for X.25-based encapsulations. The default method is HDLC. You can define the encapsulation method by performing the following task in interface configuration mode: Task Configure HSSI encapsulation. Command
encapsulation {atm-dxi | hdlc | frame-relay | ppp | sdlc-primary | sdlc-secondary | smds | stun}

For information about PPP, see the Configure SLIP and PPP chapter of the Cisco IOS Release 11.3 Access Services Configuration Guide and the Configure PPP for Wide-Area Networking chapter of the Cisco IOS Release 11.3 Wide-Area Networking Configuration Guide.

Invoke ATM on a HSSI Line

If you have an ATM DSU, you can invoke ATM over a HSSI line by mapping an ATM virtual path identifier (VPI) and virtual channel identifier (VCI) to a DXI frame address. ATM-DXI encapsulation defines a data exchange interface that allows a DTE (such as a router) and a DCE (such as an ATM DSU) to cooperate to provide a User-Network Interface (UNI) for ATM networks.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-47

Chapter 3 Configuring the 1-Port HSSI Network Module

Configuring with the Command-Line Interface

To invoke ATM over a serial line, perform the following tasks in interface configuration mode: Task Specify the encapsulation method. Map a given VPI and VCI to a DXI frame address. Command
encapsulation atm-dxi dxi map protocol address vpi vci [broadcast]

Convert HSSI to Clock Master

You can convert the HSSI interface into a 45-MHz clock master by performing the following task in interface configuration mode: Task Convert the HSSI interface into a 51.84-MHz clock master. Command
hssi internal-clock

Disable Fair Queueing

Disabling fair queuing will dramatically improve fast switching rates over the HSSI. To disable fair queueing, perform the following task in interface configuration mode: Task Disable fair queueing. Command
no fair-queue

For more information about configuring HSSI interfaces, refer to the Configuring Serial Interfaces chapter in the Cisco IOS Release 11.3 Configuration Fundamentals Configuration Guide.

Configuration Examples
The following example shows how to configure a 1-port HSSI network module on a Cisco 3600 series router. Both sides of the network connection need to be configured:
interface hssi 0/0 ip address 10.1.1.1 255.255.255.0 hssi internal-clock no fair-queue no shutdown interface hssi 1/0 ip address 10.1.1.2 255.255.255.0 hssi internal-clock no fair-queue no shutdown

In this example:

The interface hssi command specifies a HSSI interface and changes the configuration mode from global to interface. The ip address command assigns an IP address to this interface. The hssi internal-clock command sets the HSSI clock source.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-48

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the Compression Network Module for the Cisco 3600 Series Routers

The no fair-queue command disables fair queuing, which is enabled by default. This optimizes HSSI performance. The no shutdown command enables the port.

Configuring the Compression Network Module for the Cisco 3600 Series Routers
Cisco 3640 and Cisco 3620 routers now support a compression port module that provides high-performance, hardware-based data compression using simultaneous Stacker compression algorithms. Independent full-duplex compression and decompression capabilities are used on point-to-point (PPP) encapsulated packets. A routers central processing unit is generally reserved for tasks such as creating and maintaining routing tables, not performing compression duties. When a hardware compression port module is used in a router, all compression activity is offloaded from the routers central processing unit. This kind of hardware configuration is needed for routers that require B-channel compression for multiple WAN connections, such as two ISDN PRI interfaces carrying 46 B channels. Signaling over the D channel is not compressed. One compression port module supports up to 128 WAN interfaces. WAN or serial connections have limited bandwidth and greatly benefit from compressed data. For example, a hardware compression card that achieves 2:1 compression can compress 500 bytes of data down to 250 bytes. Transmission time is reduced by 50 percent. A line that transmits at 56 kbps without compress transmits at 112 kbps with compression. An achieved compression ratio or rate is dependent on the type of file being compressed. Graphics files, sound files, and text files all have different compression requirements and results. A hardware card can compress and decompress outgoing and incoming data. For negotiated compression configured between two routers, the incoming compressed data sent by the remote router is decompressed by the receiving or local compression card.

Configuration Task
You can configure point-to-point compression on interfaces that use PPP encapsulation. Compression reduces the size of a PPP frame via lossless data compression. PPP encapsulations support Stacker and Predictor compression algorithms, but the compression port module installed in Cisco 3600 series routers support only Stacker compression over PPP encapsulations. If the majority of your traffic is already compressed files, do not use compression. A hardware compression card should be used if the routers main processor CPU load exceeds 40 percent. To display the CPU load, use the show process cpu EXEC command. To configure compression over PPP, perform the following tasks in interface configuration mode: Command
Step 1 Step 2 Step 3
interface serial number encapsulation ppp

Task Specify a serial interface. Enable encapsulation of a single protocol on the serial line. Enable compression on a specified WAN interface.

compress stac

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-49

Chapter 3 Configuring the Digital Modem Network Module for the Cisco 3640 Router

Configuring with the Command-Line Interface

Configuration Example
The following example enables hardware compression and PPP encapsulation on serial interface 3/1. Although the Serial interface in slot 3/1 is configured with the compress stac command, the actual data compression takes place in the hardware compression card inserted in a different slot.
Router(config)# interface serial 3/1 Router(config-if)# encapsulate ppp Router(config-if)# compress stac Router(config-if)# exit Router(config)#

Configuring the Digital Modem Network Module for the Cisco 3640 Router
The Digital Modem Network Module for the Cisco 3640 is a high-density digital network module containing 6, 12, 18, 24, or 30 digital (MICA) modems. These modems provide a direct digital connection to an Integrated Services Digital Network (ISDN) Primary Rate Interface (PRI) channel. This digital modem network module allows the access server to support a mix of both digital data calls (ISDN) and analog modem calls over a single digital network interface. Depending on the modem license you purchase with your Cisco 3640, the modems on the Digital Modem Network Module are either manageable or not manageable by Cisco IOS software commands. If the license you purchase includes this modem management capability, you can use the modem management commands to gather call and performance statistics at any time, even if there is an active call on the modem. The Digital Modem Network Module for the Cisco 3640 provides the following benefits:

Enables you, as the Enterprise customer, to support a mix of digital (ISDN) and POTS analog modem calls over a single digital network interface. Modem management commands enable you to gather call and performance statistics. Supports 56 kbps modem connections via the K56 Flex and V.90 standards when the portware for these standards becomes available.

Prerequisites
Before you can configure a modem interface, complete the following prerequisite tasks:

Install a PRI network module and another module (such as Ethernet) to provide connectivity to the LAN. Digital modem network modules do not provide physical network interfaces of their own, but instead handle analog calls passing through the PRI network module. The PRI module is capable of concurrently handling digital ISDN data and remote voice-channel (analog) modem connections. The digital modem module provides a pool of available modems that can be used for both incoming and outgoing calls. For information on how to correctly install a PRI network module, refer to the 1-Port and 2-Port ISDN-PRI Network Module Configuration Note. For information on how to install an Ethernet module, refer to the 1-Port Ethernet Network Module Configuration Note or the 4-Port Ethernet Network Module Configuration Note. For other modules, refer to the specific configuration notes pertaining to them.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-50

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the Digital Modem Network Module for the Cisco 3640 Router

Note

The PRI module must be hardware revision -03; earlier revisions are incompatible with digital modem modules. For more information, refer to the Software and Hardware Requirements section in the Digital Modem Network Module Configuration Notes. Install the Digital Modem Network Module in a chassis slot. For information on how to correctly install this network module, refer to the Installing a Digital Modem Network Module in a Chassis Slot section in the Digital Modem Network Module Configuration Note. Complete basic device configuration, including host name, username, protocol, and security configuration. Make sure that you have the following information:
ISDN PRI Switch type T1 (or E1) information, such as line code and framing type Channel-group information and time-slot mapping

Configuration Tasks
Complete the following tasks to configure the digital modem module interfaces:

Configure the E1/T1 Network Module for ISDN PRI, page 3-51 Configure the ISDN D-Channel Serial Interfaces, page 3-53 Configure the Loopback Interface, page 3-54 Configure the LAN Interface, page 3-55 Create the Group Asynchronous Interface, page 3-55 Configure the ISDN Dialer Interface, page 3-56 Configure the Default IP Pool Information, page 3-57 Configure Modem Lines for Dial-In and Dial-Out, page 3-57

These tasks are described in the following sections.

Configure the E1/T1 Network Module for ISDN PRI

The first step in configuring a digital modem interface is to configure ISDN PRI on either a channelized T1 or E1 controller, depending on the ISDN service in your area. The ISDN PRI network modules can have either one or two ports; if the ISDN PRI module installed in your device has two ports, you need to apply the following procedure to both ports.

Configure Channelized E1 ISDN PRI

To configure ISDN PRI on a channelized E1 controller, perform the following tasks, beginning in global configuration mode: Command Description

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-51

Chapter 3 Configuring the Digital Modem Network Module for the Cisco 3640 Router

Configuring with the Command-Line Interface

isdn switch-type switch type

Select a service provider switch type that accommodates PRI. Table 3-12 shows a list of supported switch types. Specify a controller type and define its location in the Cisco 3640. Define the framing characteristics as cyclic redundancy check 4 (CRC4). Define the line code as high-density bipolar 3 (HDB3). Configure ISDN PRI. This command specifies the time slots on the T1 line to be allocated to PRI service.

controller e1 slot/unit

framing crc4

linecode hdb3

pri-group [timeslots range]

Note

The values used in this procedure for the framing and linecode commands are examples only. Use the framing type and line encoding specified by your E1 service provider.

Country Australia Europe Japan North America

ISDN Switch Type primary-ts01 primary-net5 primary-ntt primary-4ess primary-5ess primary-dms100

For more information about configuring ISDN PRI on a channelized E1 controller, refer to the Configure ISDN PRI section of the Cisco IOS Release 11.3 Dial Solutions Configuration Guide.

Configure Channelized T1 ISDN PRI

To configure ISDN PRI on a channelized T1 controller, perform the following tasks, beginning in global configuration mode: Command
isdn switch-type switch type

Description Select a service provider switch type that accommodates PRI. Table 3-12 shows a list of supported switch types. Specify a controller type and define its location in the Cisco 3640. Specify the clock source for the selected module. Define the framing characteristics as extended superframe format (ESF).

controller t1 slot/unit

clock source line framing esf

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-52

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the Digital Modem Network Module for the Cisco 3640 Router

linecode b8zs

Define the line code as binary 8 zero substitution (B8ZS) Configure ISDN PRI. This command specifies the time slots on the T1 line to be allocated to PRI service.

pri-group [timeslots range]

Note

The values used in this procedure for the framing and linecode commands are examples only. Use the framing type and line encoding specified by your E1 service provider. For more information about configuring ISDN PRI on a channelized T1 controller, refer to the Configure ISDN PRI section of the Cisco IOS Release 11.3 Dial Solutions Configuration Guide.

Note

Any router configured for ISDN support must be connected to the same switch type on all of its ISDN interfaces.

Configure the ISDN D-Channel Serial Interfaces

When you configure ISDN PRI on the channelized E1 or channelized T1 controller, you create a corresponding D-channel serial interface used to carry signaling messages for that PRI group. For E1 serial interfaces, slot/port 0:15 is the D-channel. For T1 modules, serial interface 0:23 is the D-channel. You must configure this signaling interface to receive incoming and modem calls. As mentioned, the PRI Network Module for the Cisco 3600 series can have either one or two ports. Because of this, you might have multiple D-channels to configure.

Configure the ISDN D-Channel Serial Interface for E1 Modules

To configure the ISDN D-channel serial interface for E1 modules, perform the following tasks, beginning in global configuration mode: Command
interface Serialslot/port:15

Description Specify the D-channel of the first PRI line and switch to the interface configuration mode. Disable IP processing on this interface. Set the Point-to-Point Protocol (PPP) as the encapsulation method used by this interface. Configure all incoming voice calls to go to the modems. Create a rotary dialer group. Assign the D-channel interface(s) to the defined rotary dialer group. Disable fair weighted queuing for this interface.

no ip address encapsulation ppp

isdn incoming-voice modem

dialer rotary-group number dialer-group number

no fair-queue

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-53

Chapter 3 Configuring the Digital Modem Network Module for the Cisco 3640 Router

Configuring with the Command-Line Interface

no cdp enable

Disable Cisco Discovery Protocol (CDP) on this interface.

For more information about configuring E1 ISDN D-channel serial interfaces, refer to the Configure ISDN PRI section in the Cisco IOS Release 11.3 Dial Solutions Configuration Guide.

Configure the ISDN D-Channel Serial Interface for T1 Modules

To configure the ISDN D-channel serial interface for T1 modules, perform the following tasks, beginning in the global configuration mode: Command
interface Serialslot/port:23

no ip address encapsulation ppp

isdn incoming-voice modem

dialer rotary-group number dialer-group number

no fair-queue no cdp enable

For more information about configuring T1 ISDN D-channel serial interfaces, refer to the Configure ISDN PRI section in the Cisco IOS Release 11.3 Dial Solutions Configuration Guide.

Configure the Loopback Interface

The loopback 0 interface is the interface dial-in users access when dialing in to the network. Usually, all dial-in users are assigned to a single IP subnet. This subnet can be identified with the loopback 0 interface, a logical interface whose network number can be borrowed by each asynchronous dial-in interface. To configure the loopback 0 interface, perform the following tasks, beginning in global configuration mode: Command
Step 1 Step 2
interface Loopback number ip address ip-address ip-address mask

Description Select the loopback 0 interface. Assign an IP address and subnet mask to the loopback 0 interface.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-54

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the Digital Modem Network Module for the Cisco 3640 Router

Configure the LAN Interface

The next task you need to perform is to configure the LAN interfaces on your Cisco 3600 series router. For the purpose of this procedure, we are showing how to configure an Ethernet interface. If the interface you are configuring is different, refer to the Configuring LAN Interfaces chapter in the Cisco IOS Release 11.3 Configuration Fundamentals Configuration Guide or to the configuration notes that shippedwith your module. To configure an Ethernet interface, perform the following tasks, beginning in global configuration mode: Command
Step 1 Step 2 Step 3
interface ethernet slot/port ip address ip-address ip-address mask no shutdown

Description Select the Ethernet interface. Assign an IP address and subnet mask to the Ethernet interface. Enable this interface

Note

The Ethernet and loopback interfaces should be on different subnets.

Create the Group Asynchronous Interface

A group asynchronous interface is a parent interface that applies protocol characteristics to specified, associated asynchronous interfaces. After you create a group asynchronous interface, all associated asynchronous interfaces (called members) can be configured through it. Group asynchronous interfaces can speed configuration time and help you maintain interface configuration consistency. To configure a group asynchronous interface, perform the following tasks, beginning in global configuration mode: Command
Step 1 Step 2
interface group-async number ip unnumbered Loopback number

Description Create a group asynchronous interface. Enable IP processing on the loopback interface without assigning an explicit IP address to the interface. Set the Point-to-Point Protocol (PPP) as the encapsulation method used by this interface. Enable SLIP and PPP EXEC commands on this interface. Specify an IP address from the defined IP address pool to be returned to a remote peer connecting to this interface. Disable CDP on this interface.

Step 3

encapsulation ppp

Step 4 Step 5

async mode interactive

peer default ip address pool name

Step 6

no cdp enable

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-55

Chapter 3 Configuring the Digital Modem Network Module for the Cisco 3640 Router

Configuring with the Command-Line Interface

Step 7

group-range start-range end-range

Associate one or more interfaces to the group interface so that all associated interfaces can be configured through the group interface.

For more information about group asynchronous interfaces, refer to the Asynchronous Configuration Task List section of the Cisco IOS Release 11.3 Dial Solutions Configuration Guide.

Configure the ISDN Dialer Interface

The ISDN dialer interface is the parent interface that holds the central protocol characteristics for the ISDN D channels that are part of the dialer-rotary group. To configure the ISDN dialer interface, perform the following tasks, beginning in global configuration mode: Command
Step 1 Step 2
interface Dialer number ip unnumbered Loopback number

Description Define a dialer rotary group leader. Enable IP processing on the loopback interface without assigning an explicit IP address to the interface. Disable IP multicast fast switching. Set the PPP as the encapsulation method used by this interface. Specify an IP address from the defined IP address pool to be returned to a remote peer connecting to this interface. Specify that dial-on-demand routing (DDR) be supported. Assign this interface to the rotary dialer group. Disable fair weighted queuing for this interface. Disable CDP on this interface. Enable Multilink PPP on this interface. Configure the enhanced IGRP routing process. Enable Enhanced IGRP. Disable sending routing updates on this interface. Transmit subprefix routing information across classful network boundaries.

Step 3 Step 4 Step 5

no ip mroute-cache encapsulation ppp

peer default ip address pool name

Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Step 12 Step 13 Step 14

dialer in-band

dialer-group number no fair-queue no cdp enable ppp multilink router eigrp autonomous-system-number network network-number passive-interface Dialer number no auto-summary

For more information about configuring ISDN dialer interfaces, refer to the Cisco IOS Release 11.3 Dial Solutions Configuration Guide.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-56

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring the Digital Modem Network Module for the Cisco 3640 Router

Configure the Default IP Pool Information

You need to set a range of IP addresses in the default IP pool. These IP addresses are used for dial-in users. To set the range of addresses, perform the following task in global configuration mode: Command
Step 1
ip pool local default low-ip-address [high-ip-address] ip default gateway number

Description Set the range of addresses in the default IP pool to be assigned to inbound callers. Define a default gateway (router) when IP routing is disabled. Forward packets destined for a subnet of a network that has no network default route.

Step 2 Step 3

ip classless

For more information about defining IP pool information, refer to the Cisco IOS Release 11.3 Network Protocols Configuration Guide, Part 1.

Configure Modem Lines for Dial-In and Dial-Out

The final task in configuring the MICA digital modem network modules is to configure the modem lines for dial-in and dial-out.

Configure the Modem for Dial-In

To configure the modem lines for dial-in, perform the following tasks, beginning in global configuration mode: Command
Step 1 Step 2 Step 3 Step 4
line start-range end-range

Description Select the modem lines for dial-in and switch to the line configuration mode. Set the router to display a login prompt to modem callers. Set the router to shift automatically to PPP mode if it detects an incoming PPP packet. Configure the line for both incoming and outgoing calls.

autoseect during-login

autoselect ppp

modem inout

Configure the Modem for Dial-Out

To configure the modem lines for dial-out, perform the following tasks, beginning in global configuration mode: Command
Step 1
line start-range end-range

Description Select the modem lines for dial-out and switch to the line configuration mode.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-57

Chapter 3 Configuring 1-Port G.SHDSL WAN Interface Card

Configuring with the Command-Line Interface

Step 2 Step 3

rotary number

Set the router to use previously-defined rotary group. Configure the router to accept inbound Telnet connections.

transport input telnet

This configuration procedure ensures that a user trying to dial out using Telnet is connected to the first free line in the rotary group.

Configuration Example
Refer to theAppendix A, Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls for an example of the configuration.

Configuring 1-Port G.SHDSL WAN Interface Card

This section describes how to configure the Multirate Symmetrical High-Speed Digital Subscriber Line (G.SHDSL) feature supported on the 1-port G.SHDSL WAN interface card (WIC) (WIC-1SHDSL) on Cisco 2600 series and Cisco 3600 series routers in Cisco IOS Release 12.2(4)T. This section includes the following sections:

Restrictions, page 3-59 Prerequisites, page 3-59 Configuration Tasks, page 3-59 Configuration Examples, page 3-64

G.SHDSL is ATM-based, multirate, high-speed (up to 2.3 MB), symmetrical digital subscriber line digital data transfer between a single customer premises equipment (CPE) subscriber and a central office. G.SHDSL is supported on the G.SHDSL WAN interface card, a 1-port WAN interface card (WIC) for Cisco 2600 series and Cisco 3600 series routers. The G.SHDSL WIC is compatible with the Cisco 6015, Cisco 6130, Cisco 6160, and Cisco 6260 Digital Subscriber Line Access Multiplexers (DSLAMs). The DSLAM must be equipped with G.SHDSL line cards that are compatible with the DSL service to be configured. The G.SHDSL WIC supports ATM Adaptation Layer 2 (AAL2), ATM Adaptation Layer 5 (AAL5), and various classes of quality of service (QoS) for both voice and data service. Listed below are some benefits of this feature:

Enables business-class broadband service with voice integration, scalable performance, flexibility, and security. Aggregates G.SHDSL and other transport options into a single box. Provides G.SHDSL high-speed digital data transmissions between customer premises equipment (CPE) and the central office (CO), or between routers located within a customer site. Supports ITU G.991.2 (SHDSL). Supports ANSI T1.601 (BRI), ANSI T1.410 (DDS), and ANSI T1.403 (T1 carrier).

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-58

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring 1-Port G.SHDSL WAN Interface Card

Supports AAL2 and AAL5 services and applications (including voice), ATM class of service (constant bit rate [CBR], variable bit rate-nonreal time [VBR-nrt], variable bit rate-real time [VBR-rt], and unspecified bit rate [UBR and UBR+]), and up to 23 virtual circuits on a WIC in Cisco 2600 series and Cisco 3600 series routers. Provides ATM traffic management and quality of service (QoS) features to enable service providers to manage their core ATM network infrastructures.

This feature is supported on the following router platforms:

Cisco 2610 Cisco 2611 Cisco 2612 Cisco 2613 Cisco 2620 Cisco 2621 Cisco 2650 Cisco 2651 Cisco 3620 Cisco 3640 Cisco 3661 Cisco 3662

Restrictions

The ADSL WAN does not support dual latency. When the DSL link is intended to support both voice and data traffic simultaneously, the total supported data rate must be reduced to adjust for the reduced coding gain, which is usually present with high-latency traffic. The ADSL WAN does not support Dying Gasp in ANSI T1.413 Issue 2. The ADSL WAN does not support available bit rate (ABR) class of service (CoS). The ADSL WAN should be insertedonly into onboard WIC slots or 1FE2W, 2W, 1FE1R, 2FE2W network modules. This WIC is not supported in old combination network modules.

Prerequisites
A G.SHDSL WIC must be installed in the router to match the DSL service to be configured. A compatible G.SHDSL line card must be installed in the DSLAM.

Configuration Tasks
See the following sections for configuration tasks for this feature. Each task in the list is identified as either required or optional:

Configuring G.SHDSL on a Cisco Router, page 3-60 (required)

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-59

Chapter 3 Configuring 1-Port G.SHDSL WAN Interface Card

Configuring with the Command-Line Interface

Configuring ILMI on the DSLAM Connected to the ADSL WAN, page 3-62 (optional) Verifying ATM Configuration, page 3-62 (optional)

Configuring G.SHDSL on a Cisco Router

To configure G.SHDSL service on a Cisco router containing a G.SHDSL WIC, complete the following steps, beginning in global configuration mode: Command
Step 1 Router(config)# interface atm
1/0

Purpose Enters ATM configuration mode for interface ATM 0 in slot 1.

Note

If a slot has two subslots for WIC modules and no ATM interface is present in subslot 0, the WIC will take ATM x/0 as its interface number even if placed in subslot 1 (ATMx/1). If a two-port ATM module is present in subslot 0, the WIC will use ATM x/2 as its interface number. This subslot number is pertainent to all interface commands such as show interface atm and show dsl interface atm.

Step 2 Router(config-if)# ip-address

IP-address

Assigns an IP address to the DSL ATM interface. (Optional) Enables Integrated Local Management Interface (ILMI) keepalives. If you enable ILMI keepalives without specifying the seconds, the default time interval is 3 seconds.

Step 3 Router(config-if)# atm

ilmi-keepalive seconds

Step 4 Router(config-if)# pvc [name]

vpi/vci

Enters atm-virtual-circuit (interface-atm-vc) configuration mode, and configures a new ATM permanent virtual circuit (PVC) by assigning a name (optional) and VPI/VCI numbers. The default traffic shaping is UBR; the default encapsulation is AAL5+LLC/SNAP.

Step 5 Router(config-if-vc)# protocol

ip IP-address

(Optional) Enables IP connectivity and create a point-to-point IP address for the virtual circuit (VC). (Optional) Configures the PVC for real-time variable bit rate (VBR) traffic shaping.

Step 6 Router(config-if-vc)# vbr-rt

peak-rate average-rate burst

Peak ratePeak information rate (PIR) Average rateAverage information rate (AIR) BurstBurst size in cells

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-60

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring 1-Port G.SHDSL WAN Interface Card

Command
Step 7 Router(config-if-vc)#
encapsulation {aal1 | aal2 | aal5ciscoppp | aal5mux | aal5nlpid | aal5snap}

Purpose (Optional) Configures the ATM adaptation layer (AAL) and encapsulation type.

aal1AAL1 aal2AAL2 aal5ciscopppCisco PPP over AAL5 aal5muxAAL5+MUX aal5nlpidAAL5+NLPID aal5snapAAL5+LLC/SNAP (the default)

Step 8 Router(config-if-vc)# exit Step 9 Router(config-if)# dsl

operating-mode {gshdsl symmetric annex {A | B}

Exits from interface-atm-vc configuration mode. Configures the DSL interface to operate in a specified DSL mode:

gshdslConfigures multirate, high-speed DSL per ITU G.991.2 symmetricConfigures symmetrical mode per ITU G.992.1. annexConfigures the regional operating parameters. ASets the operating parameters for North America. This value is the default. BSets the operating parameters for Europe.

The default is gshdsl symmetric annex A

Step 10 Router(config-if)#
equipment-type {co | cpe}

Configures the DSL interface to function as central office equipment or customer premises equipment:

coThe WIC functions as central office equipment and can interface with another G.SHDSL WIC configured as cpe. cpeThe WIC functions as customer premises equipment and can interface with a DSLAM or with another G.SHDSL WIC configured as co.

The default is cpe.

Step 11 Router(config-if)# dsl linerate Configures the DSL line rate:
{kbps | auto }

kbpsLine rate (data transfer rate) in kilobits per second. Allowable entries are 72, 136, 200, 264, 392, 520, 776, 1032, 1160, 1544, 2056, and 2312. autoThe WIC automatically trains for an optimal line rate by negotiating with the far-end DSLAM or WIC.

The default is auto.

Step 12 Router(config-if)# exit Step 13 Router(config)# exit

Exits from ATM interface configuration mode. Exits from global configuration mode.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-61

Chapter 3 Configuring 1-Port G.SHDSL WAN Interface Card

Configuring with the Command-Line Interface

Command
Step 14 Router# show interface atm 1/0

Purpose Verifies the ATM interface configuration.

Step 15 Router# clear interface atm 1/0 Permits the configuration changes to take effect.

Configuring ILMI on the DSLAM Connected to the ADSL WAN

The ILMI protocol allows DSLAMs to be used for ATM address registration across an ATM User-Network Interface (UNI). If ILMI is configured on the G.SHDSL WIC, the ATM PVC must be configured on the DSLAM. All switch terminating connections use interface 0/0 to connect to the switch CPU. For information about configuring the DSLAM, see the Configuration Guide for Cisco DSLAMs with NI-2.

Verifying ATM Configuration

Use the following commands to verify your configuration:

To verify current configuration and to view the status for all controllers, use the show running-config command. To view ATM controller statistics, use the show controllers atm slot/port command. To verify the PVC status, use the show atm vc command. Make sure that active PVCs are up. To help identify ATM related events as they are generated, use the debug atm events command. To indicate which interfaces are having trouble, use the debug atm errors command. To identify an entry for the ATM interface you configured and to show an entry for the ATM slot/port you configured, use the show ip route command. To view the status of an ATM interface, use the show interface atm command. Make sure that the ATM slot/port and the line protocol are up, as shown in the following examples:
Router# show interface atm 1/0 ATM1/0 is up, line protocol is up Hardware is DSLSAR (with Globespan G.SHDSL Module) MTU 4470 bytes, sub MTU 4470, BW 800 Kbit, DLY 2560 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ATM, loopback not set Keepalive not supported Encapsulation(s):AAL5 AAL2, PVC mode 24 maximum active VCs, 256 VCs per VP, 2 current VCCs VC idle disconnect time:300 seconds Last input never, output 00:00:01, output hang never Last clearing of "show interface" counters 03:16:00 Queueing strategy:fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 30 second input rate 0 bits/sec, 0 packets/sec 30 second output rate 0 bits/sec, 0 packets/sec 2527 packets input, 57116 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 10798 packets output, 892801 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out Router# show atm vc VCD /

Peak

Avg/Min Burst

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-62

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Configuring 1-Port G.SHDSL WAN Interface Card

Interface 1/0.3 1/0.2

Name 2 1

VPI 9 9

VCI 36 37

Type PVC PVC

Encaps MUX SNAP

SC UBR UBR

Kbps Kbps 800 800

Cells

Sts UP UP

Router# show controllers atm 1/0 Interface ATM1/0 is up Hardware is DSLSAR (with Globespan IDB: 62586758 Instance:6258E054 PHY Inst:62588490 Ser0Inst:62573074 Slot: 1 Unit: 1 VCperVP:256 max_vp: 256 rct_size:65536 vpivcibit:16 vpvc_sel:3 enabled: 0 WIC Register --------------FPGA Dev ID (LB) FPGA Dev ID (UB) FPGA Revision WIC Config Reg Value ---------0x44 0x53 0x99 0x45

G.SHDSL Module) reg_dslsar:3C810000 wic_regs:3C810080 Ser1Inst: 6257CBD8 us_bwidth:800 Subunit: 0 pkt Size:4496 max_vc: 65536 total vc:2 connTblVCI:8 vpi_bits:8 throttled:0

Notes ---------'D' 'S' WIC / VIC select = WIC; CTRLE addr bit 8 = 1; OK LED on; LOOPBACK LED off; CD LED on; Gen bus error on bad ADSL access ADSL normal interrupt enabled ADSL error interrupt enabled

WIC Config Reg2 Int 0 Enable Reg

0x07 0x03

To view the status of the G.SHDSL modem, use the show dsl interface atm command. If the line is down, the following statement appears: Line is not active. Some of the values may not be accurate. You can also verify whether the equipment type and operating mode configuration are correct for your application.

The following sample output shows a WIC configured as central office equipment, and the line is up:
Router# show dsl interface atm 0/0 Globespan G.SHDSL Chipset Information Equipment Type: Central Office Operating Mode: G.SHDSL Clock Rate Mode: Auto rate selection Mode Reset Count: 2 Actual rate: 2320 Kbps Modem Status: Data Noise Margin: 43 dB Loop Attenuation: 0.0 dB Transmit Power: 13.5 dB Receiver Gain: 204.8000 dB Last Activation Status:No Failure CRC Errors: 0 Chipset Version: 1 Firmware Version: R1.0 Farend Statistics since CO boot-time: CRC Errors: Errored Seconds: Severly ES: Un Available S: Loss Of Sync S: 0 0 0 48 0

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-63

Chapter 3 Saving Configuration Changes

Configuring with the Command-Line Interface

The following sample output shows a WIC configured as customer premises equipment, and the line is up:
Router# show dsl interface atm 0/0 Globespan G.SHDSL Chipset Information Equipment Type: Customer Premise Operating Mode: G.SHDSL Clock Rate Mode: Auto rate selection Mode Reset Count: 1 Actual rate: 2320 Kbps Modem Status: Data Noise Margin: 42 dB Loop Attenuation: 0.0 dB Transmit Power: 13.5 dB Receiver Gain: 204.8000 dB Last Activation Status:No Failure CRC Errors: 0 Chipset Version: 1 Firmware Version: R1.0

Configuration Examples
Configuration examples are provided in the following sections:

Configuration in CPE Mode Example, page A-25 Configuration in CO Mode Example, page A-27

To prevent the loss of the router configuration, save it to NVRAM.

Saving Configuration Changes

Command
Step 1 Router> enable
Password: password Router#

Purpose Enters enable mode. Enter the password. You have entered enable mode when the prompt changes to Router#. that they are not lost during resets, power cycles, or power outages.

Step 2 Router# copy running-config startup-config Saves the configuration changes to NVRAM so

Step 3 Router(config-if)# Ctrl-z

Router# %SYS-5-CONFIG_I: Configured from console by console

Returns to enable mode. This message is normal and does not indicate an error.

Where to Go Next
At this point you can proceed to the following:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-64

OL-1957-04

Chapter 3

Configuring with the Command-Line Interface Where to Go Next

The Cisco IOS software configuration guide and command reference publications for more advanced configuration topics. These publications are available on Cisco.com, the Documentation CD-ROM that came with your router, or you can order printed copies. The System Error Messages and Debug Command Reference publications for troubleshooting information. These publications are available on Cisco.com, the Documentation CD-ROM that came with your router, or you can order printed copies.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

3-65

Chapter 3 Where to Go Next

Configuring with the Command-Line Interface

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

3-66

OL-1957-04

C H A P T E R

Configuring Voice-over-IP
This chapter explains how to configure voice network modules with receive and transmit (E&M), Foreign Exchange Office (FXO), and Foreign Exchange Station (FXS) interfaces for your router. Voice network modules convert telephone voice signals into a form that can be transmitted over an IP network. This chapter is divided into the following sections:

Voice-over-IP Prerequisites, page 4-1 Configuring the Voice Interface, page 4-2 Voice-over-IP Configuration Examples, page 4-3 Where to Go Next, page 4-11

You need both a voice network module and a voice interface card for a voice connection. You can install one voice interface card in a 2-channel voice network module, and two voice interface cards in a 4-channel module. At least one other network module or WAN interface card must be installed in the router to provide the connection to the IP LAN or WAN. Voice over IP (VoIP) enables your router to carry live voice traffic (for example, telephone calls and faxes) over an IP network. VoIP offers the following benefits:

Toll bypass Remote PBX presence over WANs Unified voice/data trunking Plain old telephone service (POTS)-Internet telephony gateways

Voice-over-IP Prerequisites
Before you can configure your router to use VoIP, you must first do the following:

Establish a working IP network. For more information about configuring IP, refer to the Configuring IP chapter in the Cisco IOS Release 11.3 Release Network Protocols Configuration Guide, Part 1. Install the voice network module into your router. For more informationabout the voice network modules, refer to the Connecting Voice Network Modules to a Network chapter in the Cisco Network Modules Hardware Installation Guide. Complete your companys dial plan. That is, decide what patterns of dialed numbers will access what telephony endpoints. Establish a working telephony network based on your companys dial plan. Integrate your dial plan and telephony network into your existing IP network topology.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

4-1

Chapter 4

Configuring Voice-over-IP

Configuring the Voice Interface

Whenever you install a new interface, or if you want to change the configuration of an existing interface, you must configure the interface. If you replace a module that was already configured, the router recognizes it and brings up the interface in the existing configuration. Before you configure an interface, have the following information available:

Protocols you plan to route on the new interface IP addresses, subnet masks, network numbers, zones, or other information related to the routing protocol

Timesaver

Obtain this information from your system administrator or network plan before you begin router configuration. To configure a voice interface, you must use configuration mode (manual configuration). In this mode, you can enter Cisco IOS commands at the router prompt. Before you begin, disconnect all WAN cables from the router to keep it from trying to run the AutoInstall process. The router tries to run AutoInstall whenever you power it on if there is a WAN connection on both ends, and the router does not have a valid configuration file stored in NVRAM (for instance, when you add a new interface). It can take several minutes for the router to determine that AutoInstall is not connected to a remote Transmission Control Protocol/Internet Protocol (TCP/IP) host. To configure the voice interface configuration mode, follow this procedure:

Step 1 Step 2

Connect a console to the router. If you need instructions for connecting a console, refer to the installation chapter of your router installation and configuration guide. Power onthe router. If the current configuration is no longer valid, after about one minute you see the following prompt:
Would you like to enter the initial dialog? [yes/no]:

Answer no. You now enter the normal operating mode of the router.
Note Step 3

If the current configuration is valid, you enter the normal operating mode automatically.

After a few seconds, you see the user EXEC prompt (Router>). Type enable and the password to enter enable mode:
Router> enable Password: <password>

Configuration changes can be made only in enable mode. The prompt changes to the privileged EXEC (enable) prompt (Router#):
Router#

Step 4

Enter the configure terminal command to enter configuration mode:

Router# configure terminal Router(config)#

The router enters global configuration mode, indicated by the Router(config)# prompt.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

4-2

OL-1957-04

Chapter 4

Configuring Voice-over-IP

Step 5

If you have not configured the router before, or want to change the configuration, use Cisco IOS commands to configure global parameters, passwords, network management, and routing protocols. In this example, IP routing is enabled:
Router(config)# ip routing

For complete information about global configuration commands, refer to the Cisco IOS configuration guides and command references.
Step 6

If you have not already done so, configure the network module or WAN interface card that you plan to use for IP traffic. For instructions, see your routers installation and configuration guide or the configuration note for the network module or WAN interface card. To configure another interface, enter the exit command to return to the
Router(config)#

Step 7 Step 8 Step 9

prompt.

To configure the router for voice traffic, refer to the detailed instructions in the Voice over IP Configuration document. When you finish configuring interfaces, exit configuration mode and return to the enable prompt by pressing Ctrl-z. To see the current operating configuration, including any changes you just made, enter the show running-config command:
Router# show running-config

To see the configuration currently stored in NVRAM, enter the show startup-config command at the enable prompt:
Router# show startup-config

Step 10

The results of the show running-config and show startup-config commands differ from each other if you have made changes to the configuration, but have not yet written them to NVRAM. To write your changes to NVRAM, making them permanent, enter the copy running-config startup-config command at the enable prompt:
Router# copy running-config startup-config Building configuration. . . [OK] Router#

The router is now configured to boot in the new configuration.

Voice-over-IP Configuration Examples

The actual VoIP configuration procedure you complete depends on the topology of your voice network. The following configuration examples should give you a starting point. Of course, these configuration examples would need to be customized to reflect your network topology. Configuration procedures are supplied for the following scenarios:

FXS-to-FXS Connection Using RSVP, page 4-4 Linking PBX Users with E&M Trunk Lines, page 4-6 PSTN Gateway Access Using FXO Connection, page 4-8 PSTN Gateway Access Using FXO Connection (PLAR Mode), page 4-9 Configuring Direct-Inward Dialing on a BRI Port, page 4-10

These examples are described in the following sections.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

4-3

Chapter 4

Configuring Voice-over-IP

FXS-to-FXS Connection Using RSVP

The following example shows how to configure VoIP for simple FXS-to-FXS connections. In this example, a very small company, consisting of two offices, has decided to integrate VoIP into its existing IP network. One basic telephony device is connected to Router RLB-1; therefore Router RLB-1 has been configured for one POTS peer and one VoIP peer. Router RLB-w and Router R12-e establish the WAN connection between the two offices. Because one POTS telephony device is connected to Router RLB-2, it has also been configured for only one POTS peer and one VoIP peer. In this example, only the calling end (Router RLB-1) is requesting RSVP. Figure 4-1 illustrates the topology of this FXS-to-FXS connection example.
Figure 4-1 FXS-to-FXS Connection Example

Configuration for Router RLB-1

hostname rlb-1 ! Create voip dial-peer 10 dial-peer voice 10 voip ! Define its associated telephone number and IP address destination-pattern +4155264000 sess-target ipv4:40.0.0.1 ! Request RSVP req-qos guaranteedDelay ! Create pots dial-peer 1 dial-peer voice 1 pots ! Define its associated telephone number and voice port destination-pattern +4085264000 port 1/0/0 ! Configure serial interface 0/0 interface Serial0/0 ip address 10.0.0.1 255.0.0.0 no ip mroute-cache ! Configure RTP header compression ip rtp header-compression ip rtp compression-connections 25 ! Enable RSVP on this interface ip rsvp bandwidth 48 48 fair-queue 64 256 36 clockrate 64000 router igrp 888 network 10.0.0.0 network 20.0.0.0 network 40.0.0.0

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

4-4

OL-1957-04

Chapter 4

Configuring Voice-over-IP

Configuration for Router RLB-w

hostname rlb-w ! Configure serial interface 1/0 interface Serial1/0 ip address 10.0.0.2 255.0.0.0 ! Configure RTP header compression ip rtp header-compression ip rtp compression-connections 25 ! Enable RSVP on this interface ip rsvp bandwidth 96 96 fair-queue 64 256 3 ! Configure serial interface 1/3 interface Serial1/3 ip address 20.0.0.1 255.0.0.0 ! Configure RTP header compression ip rtp header-compression ip rtp compression-connections 25 ! Enable RSVP on this interface ip rsvp bandwidth 96 96 fair-queue 64 256 3 ! Configure IGRP router igrp 888 network 10.0.0.0 network 20.0.0.0 network 40.0.0.0

Configuration for Router R12-e

hostname r12-e ! Configure serial interface 1/0 interface Serial1/0 ip address 40.0.0.2 25.0.0.0 ! Configure RTP header compression ip rtp header-compression ip rtp compression-connections 25 ! Enable RSVP on this interface ip rsvp bandwidth 96 96 fair-queue 64 256 3 ! Configure serial interface 1/3 interface Serial1/3 ip address 20.0.0.2 255.0.0.0 ! Configure RTP header compression ip rtp header-compression ip rtp compression-connections 25 ! Enable RSVP on this interface ip rsvp bandwidth 96 96 fair-queue 64 256 3 clockrate 128000 ! Configure IGRP router igrp 888 network 10.0.0.0 network 20.0.0.0 network 40.0.0.0

Configuration for Router RLB-2

hostname r1b-2 ! Create pots dial-peer 2 dial-peer voice 2 pots ! Define its associated telephone number and voice-port

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

4-5

Chapter 4

Configuring Voice-over-IP

destination-pattern +4155264000 port 1/0/0 ! Create voip dial-peer 20 dial-peer voice 20 voip !Define its associated telephone number and IP address destination-pattern +4085264000 sess-target ipv4:10.0.0.1 ! Configure serial interface 0/0 interface Serial0/0 ip address 40.0.0.1 255.0.0.0 no ip mroute-cache ! Configure RTP header compression ip rtp header-compression ip rtp compression-connections 25 ! Enable RSVP on this interface ip rsvp bandwidth 96 96 fair-queue 64 256 3 clockrate 64000 ! Configure IGRP router igrp 888 network 10.0.0.0 network 20.0.0.0 network 40.0.0.0

Linking PBX Users with E&M Trunk Lines

The following example shows how to configure VoIP to link PBX users with E&M trunk lines. In this example, a company wants to connect two offices: one in San Jose, California and the other in Salt Lake City, Utah. Each office has an internal telephone network using PBX, connected to the voice network by an E&M interface. Both the Salt Lake City and the San Jose offices are using E&M Port Type II, with four-wire operation and ImmediateStart signaling. Each E&M interface connects to the router using two voice interface connections. Users in San Jose dial 8-569 and then the extension number to reach a destination in Salt Lake City. Users in Salt Lake City dial 4-527 and then the extension number to reach a destination in San Jose. Figure 4-2 illustrates the topology of this connection example.
Figure 4-2 Linking PBX Users with E&M Trunk Lines Example

Note

This example assumes that the company already has established a working IP connection between its two remote offices.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

4-6

OL-1957-04

Chapter 4

Configuring Voice-over-IP

Router SJ Configuration
hostname sanjose !Configure pots dial-peer 1 dial-peer voice 1 pots destination-pattern +527.... port 1/0/0 !Configure pots dial-peer 2 dial-peer voice 2 pots destination-pattern +527.... port 1/0/1 !Configure voip dial-peer 3 dial-peer voice 3 voip destination-pattern +569.... session target ipv4:172.16.65.182 !Configure the E&M interface voice-port 1/0/0 signal immediate operation 4-wire type 2 voice-port 1/0/1 signal immediate operation 4-wire type 2 !Configure the serial interface interface serial 0/0 description serial interface type dce (provides clock) clock rate 2000000 ip address 172.16.1.123 no shutdown

Router SLC Configuration

hostname saltlake !Configure pots dial-peer 1 dial-peer voice 1 pots destination-pattern +569.... port 1/0/0 !Configure pots dial-peer 2 dial-peer voice 2 pots destination-pattern +569.... port 1/0/1 !Configure voip dial-peer 3 dial-peer voice 3 voip destination-pattern +527.... session target ipv4:172.16.1.123 !Configure the E&M interface voice-port 1/0/0 signal immediate operation 4-wire type 2 voice-port 1/0/0 signal immediate operation 4-wire type 2 !Configure the serial interface interface serial 0/0 description serial interface type dte ip address 172.16.65.182 no shutdown

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

4-7

Chapter 4

Configuring Voice-over-IP

Note

PBXs should be configured to pass all DTMF signals to the router. Cisco recommends that you do not configure store-and-forward tone.

Note

If you change the gain or the telephony port, make sure that the telephony port still accepts DTMF signals.

PSTN Gateway Access Using FXO Connection

The following example shows how to configure VoIP to link users with the PSTN gateway using an FXO connection. In this example, users connected to Router SJ in San Jose, California can reach PSTN users in Salt Lake City, Utah via Router SLC. Router SLC in Salt Lake City is connected directly to the PSTN through an FXO interface. Figure 4-3 illustrates the topology of this connection example.
Figure 4-3 PSTN Gateway Access Using FXO Connection Example

Note

This example assumes that the company already has established a working IP connection between its two remote offices.

Router SJ Configuration
! Configure pots dial-peer 1 dial-peer voice 1 pots destination-pattern +14085274000 port 1/0/0 ! Configure voip dial-peer 2 dial-peer voice 2 voip destination-pattern +9........... session target ipv4:172.16.65.182 ! Configure the serial interface interface serial 0/0 clock rate 2000000 ip address 172.16.1.123 no shutdown

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

4-8

OL-1957-04

Chapter 4

Configuring Voice-over-IP

Router SLC Configuration

! Configure pots dial-peer 1 dial-peer voice 1 pots destination-pattern +9........... port 1/0/0 ! Configure voip dial-peer 2 dial-peer voice 2 voip destination-pattern +14085274000 session target ipv4:172.16.1.123 ! Configure serial interface interface serial 0/0 ip address 172.16.65.182 no shutdown

PSTN Gateway Access Using FXO Connection (PLAR Mode)

The following example shows how to configure VoIP to link users with the PSTN gateway using an FXO connection (PLAR mode). In this example, PSTN users in Salt Lake City, Utah, can dial a local number and establish a private line connection in a remote location. As in the previous example, Router SLC in Salt Lake City is connected directly to the PSTN through an FXO interface. Figure 4-4 illustrates the topology of this connection example.
Figure 4-4 PSTN Gateway Access Using FXO Connection (PLAR Mode)

Note

This example assumes that the company already has established a working IP connection between its two remote offices.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

4-9

Chapter 4

Configuring Voice-over-IP

interface serial 0/0 clock rate 2000000 ip address 172.16.1.123 no shutdown

Router SLC Configuration

! Configure pots dial-peer 1 dial-peer voice 1 pots destination-pattern +9........... port 1/0/0 ! Configure voip dial-peer 2 dial-peer voice 2 voip destination-pattern +14085274000 session target ipv4:172.16.1.123 ! Configure the voice port voice port 1/0/0 connection plar 14085274000 ! Configure the serial interface interface serial 0/0 ip address 172.16.65.182 no shutdown

Configuring Direct-Inward Dialing on a BRI Port

The following example shows how to configure a BRI port for direct-inward dialing (DID). This configuration allows the called number information from the ISDN Q.931 setup message to be used for routing on an ISDN line. In this example, a call comes in to router 1 on the BRI port. The DID information allows the router to route the call based on the called number. If the called number is 2xxx, the call is routed to router 2000, and if the called number is 3xxx, the call is routed to router 3000. Figure 4-5 illustrates the topology of this connection example.
Figure 4-5 Configuring DID on a BRI Port

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

4-10

OL-1957-04

Chapter 4

Configuring Voice-over-IP

Router 1 Configuration
dial-peer voice 1 pots port 1/0/0 destination-pattern 1... direct-inward-dial dial-peer voice 2 voip session target ipv4:1.1.1.2 destination-pattern 2... dial-peer voice 3 voip session target ipv4:1.1.1.3 destination-pattern 3...

Router 2 Configuration
dial-peer voice 1 pots port 1/0/0 destination-pattern 2000

Router 3 Configuration
dial-peer voice 1 pots port 1/0/0 destination-pattern 3000

Where to Go Next
At this point you can proceed to the following:

Voice over IP Software Configuration Guide for further information on Voice over IP configuration procedures and commands. Cisco IOS software configuration guide and command reference publications for more advanced configuration topics. These publications are available on Cisco.com, the Documentation CD-ROM that came with your router, or you can order printed copies.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

4-11

Chapter 4

Configuring Voice-over-IP

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

4-12

OL-1957-04

A P P E N D I X

Configuration Examples
This appendix shows some examples of the configuration in the Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers.

Cisco 2600 Series Router Configuration Example

Following is an example of a configuration on a Cisco 2600 series router.
The following configuration command script was created: hostname 2600 enable secret 5 $1$zxxT$YZMzUP1/wQvyLn5cWeyPu. enable password guessme line vty 0 4 password guessagain snmp-server community public ! no appletalk routing no decnet routing ip routing no clns routing no ipx routing no vines routing no xns routing no apollo routing no bridge 1 ! line 1 64 speed 115200 flowcontrol hardware login local autoselect during-login autoselect ppp modem dialin ip local pool setup_pool 172.20.30.40 172.20.30.88 ! username user password passwd line 1 64 modem output transport input all ! interface Ethernet0/0 no shutdown ip address 255.255.255.0 255.255.0.0 lat enabled

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-1

Appendix A Cisco 2600 Series Router Configuration Example

Configuration Examples

no mop enabled ! interface Serial0/0 encapsulation hdlc clock rate 2000000 ip address 1.0.0.1 255.0.0.0 lat enabled appletalk cable-range 3-3 3.3 appletalk zone myzone ipx network 8 no vines metric mop enabled ! interface Ethernet0/1 ip address 255.255.255.1 255.255.0.0 lat enabled no vines metric mop enabled ! interface Serial0/1 physical-layer sync encapsulation ppp ip address 2.0.0.1 255.0.0.0 lat enabled appletalk cable-range 6-6 6.6 appletalk zone myzone ipx network 6 no vines metric xns network 7 mop enabled ! interface Serial0/2 physical-layer async ip address 3.0.0.1 255.0.0.0 lat enabled appletalk cable-range 8-8 8.8 appletalk zone myzone ipx network 8 no vines metric mop enabled ! interface Serial1/0 physical-layer sync encapsulation frame-relay frame-relay lmi-type cisco clock rate 115200 ip address 4.0.0.1 255.0.0.0 no lat enabled no vines metric no mop enabled ! interface Serial1/1 physical-layer async ip address 5.0.0.1 255.0.0.0 no lat enabled no vines metric no mop enabled ! interface Serial1/2 physical-layer sync encapsulation x25 dte x25 address 1234 x25 map ip 1.0.0.1 4321 x25 map ipx 6.0.0.1 -2132065964

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-2

OL-1957-04

Appendix A

Configuration Examples Cisco 2600 Series Router Configuration Example

x25 ltc 1 x25 htc 64 x25 win 7 x25 wout 7 x25 threshold 2 x25 ips 128 x25 ops 128 clock rate 115200 ip address 6.0.0.1 255.0.0.0 no lat enabled no vines metric no mop enabled ! interface Serial1/3 physical-layer sync encapsulation smds smds address c141.5556.1415 no keepalive smds static-map ip 2.0.0.1 c141.5556.1414 smds static-map ipx 2.0.0.1 c141.5556.1414 clock rate 115200 ip address 172.22.50.10 255.255.0.0 no lat enabled no vines metric no mop enabled dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit ! router igrp 1 redistribute connected network 172.21.0.0 ! end

Following is an example of a configuration on the Cisco 2691 router.

C2691#show running-config Building configuration... Current configuration : 1143 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname C2691 ! enable password lab ! voice-card 1 ! ip subnet-zero ! ! no ip domain-lookup ip host rtplab-dev 172.18.207.10 ! ! ! ! fax interface-type fax-mail mta receive maximum-recipients 0 !

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-3

Appendix A Cisco 2600 Series Router Configuration Example

Configuration Examples

controller T1 1/0 framing esf linecode b8zs ds0-group 1 timeslots 1-24 type e&m-wink-start ! controller T1 1/1 framing sf linecode ami ! ! ! ! interface FastEthernet0/0 ip address 172.18.193.171 255.255.255.0 speed 100 full-duplex ! interface FastEthernet0/1 ip address 50.0.0.4 255.0.0.0 speed 100 full-duplex ! ip classless ip route 172.18.207.0 255.255.255.0 172.18.193.1 ip http server ip pim bidir-enable ! ! ! call rsvp-sync ! voice-port 1/0:1 output attenuation 3 ! ! mgcp profile default ! dial-peer cor custom ! ! ! dial-peer voice 919 pots destination-pattern 919 port 1/0:1 prefix 919 ! dial-peer voice 408 voip destination-pattern 408 session target ipv4:50.0.0.3 dtmf-relay h245-alphanumeric codec g711alaw ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 password lab login ! end

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-4

OL-1957-04

Appendix A

Configuration Examples Cisco 2600 Series Router Configuration Example

Following is an example of a configuration on the Cisco 2620XM router:

Building configuration... Current configuration : 588 bytes ! version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname c2620xm ! ! ip subnet-zero ! ! ! ! ! ! ! ! ! ! fax interface-type fax-mail mta receive maximum-recipients 0 ! ! ! ! interface FastEthernet0/0 ip address 111.0.0.29 255.255.255.0 duplex auto speed auto no cdp enable ! ip classless ip route 0.0.0.0 0.0.0.0 FastEthernet0/0 no ip http server ip pim bidir-enable ! ! no cdp run ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 line aux 0 line vty 0 4 login ! ! end

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-5

Appendix A Cisco 3631 Router Configuration Example

Configuration Examples

Cisco 3631 Router Configuration Example

Following is an example of the configuration on the Cisco 3631 router equipped with the following modules:

IMA-8T1 in NM-4A/S WIC-2A/S WIC-1DSU-56k4

Building configuration... 00:45:06: %SYS-5-CONFIG_I: Configured from console by console Current configuration : 3095 bytes ! ! Last configuration change at 12:12:59 PDT Tue Dec 4 2001 ! NVRAM config last updated at 12:12:26 PDT Tue Dec 4 2001 ! version 12.2 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname cisco3631 ! enable secret 5 $1$6UL.$w0aJJ5oZmIv1zRDl1RMvo/ ! username USER password 7 01030717481C091D25 memory-size iomem 10 clock timezone PDT -8 ip subnet-zero no ip domain-lookup ! x29 profile linemode 2:1 3:2 15:1 x25 routing ! chat-script test "" "ATDT\T" TIMEOUT 120 CONNECT \c ! ! ! ! ! ! ! ! ! ! ! interface FastEthernet0/0 description FAST ETHERNET INTERFACE ip address x.x.x.x x.x.x.x duplex auto speed auto ! interface Serial0/0 description WIC-1DSU-56k4 ip address x.x.x.x x.x.x.x encapsulation ppp ! interface Serial0/1 description WIC-2A/S physical-layer async

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-6

OL-1957-04

Appendix A

Configuration Examples Cisco 3631 Router Configuration Example

no ip address encapsulation ppp dialer in-band dialer rotary-group 3 dialer-group 1 async mode dedicated no fair-queue ! interface Serial0/2 description WIC-2A/S physical-layer async no ip address encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer rotary-group 3 dialer-group 1 async default routing async mode dedicated no fair-queue ! interface Serial1/0 description NM-4A/S no ip address encapsulation x25 x25 htc 8 ! interface Serial1/1 description NM-4A/S no ip address encapsulation x25 dce x25 ips 256 x25 ops 256 clockrate 9600 ! interface Serial1/2 no ip address shutdown ! interface Serial1/3 no ip address shutdown ! interface ATM2/0 no ip address shutdown no atm ilmi-keepalive no scrambling-payload ! interface ATM2/1 no ip address shutdown no atm ilmi-keepalive no scrambling-payload ! interface ATM2/2 description ATM T1 ip address x.x.x.x x.x.x.x no ip route-cache no ip mroute-cache no atm ilmi-keepalive pvc atm71 0/71 protocol clns 47.0004.004d.0056.0000.0c00.0003.00 broadcast

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-7

Appendix A Cisco 3631 Router Configuration Example

Configuration Examples

protocol ip 12.0.0.2 broadcast encapsulation aal5snap ! scrambling-payload impedance 120-ohm ! interface ATM2/3 no ip address shutdown no atm ilmi-keepalive no scrambling-payload ! interface ATM2/4 no ip address shutdown no atm ilmi-keepalive no scrambling-payload ! interface ATM2/5 no ip address shutdown no atm ilmi-keepalive no scrambling-payload ! interface ATM2/6 no ip address shutdown no atm ilmi-keepalive no scrambling-payload ! interface ATM2/7 no ip address shutdown no atm ilmi-keepalive no scrambling-payload ! interface ATM2/IMA0 description ATM-IMA GROUP ip address x.x.x.x x.x.x.x no ip route-cache no ip mroute-cache no atm ilmi-keepalive pvc atm71 0/71 protocol clns 47.0004.004d.0056.0000.0c00.0002.00 broadcast protocol ip 12.0.0.1 broadcast encapsulation aal5snap ! interface Dialer3 ip address x.x.x.9 x.x.x.x encapsulation ppp no ip route-cache no ip mroute-cache dialer in-band dialer idle-timeout 500 dialer map ip x.x.x.10 name USER modem-script test broadcast 9,5551122 dialer map ip x.x.x.10 name USER modem-script test broadcast 9,5551123 dialer hold-queue 15 dialer load-threshold 5 either dialer-group 1 no fair-queue no cdp enable ppp authentication chap

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-8

OL-1957-04

Appendix A

Configuration Examples Cisco 3631 Router Configuration Example

ppp multilink group-range 4 5 ! router ospf 1 redistribute connected subnets network X.X.X.X 0.0.0.X area 3 ! ! ip classless no ip http server ip pim bidir-enable ! ! ! ! ! ! ! ! ! ! ! ! snmp-server view cutdown internet included snmp-server view cutdown at excluded snmp-server community public view cutdown RO snmp-server community private view cutdown RW ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! ! ! line con 0 line 3 modem InOut transport input all autohangup stopbits 1 rxspeed 115200 txspeed 115200 flowcontrol hardware line 5 modem InOut transport input all autohangup stopbits 1 rxspeed 115200 txspeed 115200 flowcontrol hardware line 6 line aux 0 password 7 08314D5D1A0E0A0516 login modem InOut transport input all line vty 0 4 password 7 00141215174C04140B login

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-9

Appendix A Cisco 3725 Router Configuration Example

Configuration Examples

! end

Cisco 3725 Router Configuration Example

Following example shows the configurationon the Cisco 3725 router.
version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname pipertdm ! no logging buffered logging rate-limit console 10 except errors no logging console ! ! ! ip subnet-zero ! ! no ip finger ip host rtplab-tftp2 172.18.207.16 ip host rtplab-dev 172.18.207.10 ! no ip dhcp-client network-discovery no mgcp timer receive-rtcp call rsvp-sync ! ! ! ! ! fax interface-type modem mta receive maximum-recipients 0 ! ! ! ! interface FastEthernet0/0 ip address 172.18.197.74 255.255.255.252 no keepalive duplex auto speed auto no cdp enable ! interface FastEthernet0/1 ip address 2.2.2.2 255.0.0.0 no keepalive duplex auto speed auto no cdp enable ! interface BRI1/0 no ip address shutdown ! interface FastEthernet1/0

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-10

OL-1957-04

Appendix A

Configuration Examples Cisco 3725 Router Configuration Example

ip address 1.1.1.1 255.0.0.0 no keepalive duplex auto speed auto no cdp enable ! interface Serial1/0 no ip address shutdown no fair-queue clockrate 125000 ! interface FastEthernet1/1 ip address 3.3.3.3 255.0.0.0 no keepalive shutdown duplex auto speed auto no cdp enable ! interface Serial1/1 no ip address shutdown clockrate 125000 ! ip kerberos source-interface any ip classless ip route 172.18.0.0 255.255.0.0 FastEthernet0/0 ip http server ! ! ! ! snmp-server packetsize 4096 snmp-server chassis-id snmp-server manager ! ! dial-peer cor custom ! ! ! ! line con 0 exec-timeout 0 0 transport input none line 1 32 line 35 96 line aux 0 line vty 0 4 ! end

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-11

Appendix A 1-Port ADSL WAN Interface Card Configuration Examples

Configuration Examples

1-Port ADSL WAN Interface Card Configuration Examples

Following configuration examples are shown below:

VoATM over AAL2 on the ATM Interface Configuration Example, page A-12 VoATM over AAL5 on the ATM Interface Configuration Example, page A-14

VoATM over AAL2 on the ATM Interface Configuration Example

The following example shows VoATM over AAL2 on the ATM interface with an ADSL card:
Router# version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname host1 ! memory-size iomem 10 voice-card 1 ! ip subnet-zero ip host host2 225.255.255.224 ! no mgcp timer receive-rtcp call rsvp-sync ! ! controller T1 1/0 framing esf linecode b8zs ds0-group 0 timeslots 1 type e&m-wink-start ds0-group 1 timeslots 2 type e&m-wink-start . . . ds0-group 23 timeslots 24 type e&m-wink-start ! controller T1 1/1 framing esf linecode b8zs ! interface Ethernet0/0 ip address 1.6.46.119 255.255.255.224 half-duplex no cdp enable ! interface Serial0/0 no ip address shutdown ! interface ATM0/1 ip address 10.1.1.1 255.0.0.0 load-interval 30 atm vc-per-vp 256 no atm ilmi-keepalive pvc 10/100 vbr-rt 672 672 512 encapsulation aal2

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-12

OL-1957-04

Appendix A

Configuration Examples 1-Port ADSL WAN Interface Card Configuration Examples

! pvc 10/200 protocol ip 10.1.1.2 broadcast encapsulation aal5snap ! dsl operating-mode ansi-dmt no fair-queue ! interface Ethernet0/1 no ip address shutdown ! ip classless ip route 223.255.254.254 255.255.255.224 Ethernet0/0 no ip http server ! ! snmp-server engineID local 000000090200003080477F20 snmp-server manager ! voice-port 1/0:0 local-alerting timeouts wait-release 3 connection trunk 3001 ! voice-port 1/0:1 local-alerting timeouts wait-release 3 connection trunk 3002 . . . voice-port 1/0:23 local-alerting timeouts wait-release 3 connection trunk 3024 shutdown ! dial-peer cor custom ! dial-peer voice 3001 voatm destination-pattern 3001 called-number 4001 session protocol aal2-trunk session target ATM0/1 pvc 10/100 31 codec aal2-profile ITUT 1 g711ulaw no vad ! dial-peer voice 3002 voatm destination-pattern 3002 called-number 4002 session protocol aal2-trunk session target ATM0/1 pvc 10/100 32 codec aal2-profile custom 100 g726r32 no vad ! dial-peer voice 3003 voatm destination-pattern 3003 called-number 4003 session protocol aal2-trunk session target ATM0/1 pvc 10/100 33 codec aal2-profile ITUT 7 g729abr8 no vad .

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-13

Appendix A 1-Port ADSL WAN Interface Card Configuration Examples

Configuration Examples

. . dial-peer voice 3024 voatm destination-pattern 3024 called-number 3024 session protocol aal2-trunk session target ATM0/1 pvc 10/100 54 codec aal2-profile ITUT 7 g729abr8 no vad ! dial-peer voice 1 pots destination-pattern 4001 port 1/0:0 ! dial-peer voice 2 pots destination-pattern 4002 port 1/0:1 . . . dial-peer voice 24 pots destination-pattern 4024 port 1/0:23 ! line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login ! no scheduler allocate end

VoATM over AAL5 on the ATM Interface Configuration Example

The following example shows a Cisco 2600 series router configured for VoATM over AAL5 on the ATM interface with an ADSL card.
Router# version 12.2 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname u2621 ! no logging buffered no logging buffered logging rate-limit console 10 except errors ! memory-size iomem 15 voice-card 1 ! ip subnet-zero ! no ip finger no ip domain-lookup ! no mgcp timer receive-rtcp call rsvp-sync

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-14

OL-1957-04

Appendix A

Configuration Examples 1-Port ADSL WAN Interface Card Configuration Examples

! controller T1 1/0 framing esf linecode b8zs ds0-group 0 timeslots 1-24 type e&m-wink-start ! controller T1 1/1 ! ! interface ATM0/0 ip address 12.0.0.1 255.255.255.224 load-interval 30 atm vc-per-vp 256 no atm ilmi-keepalive dsl operating-mode auto no fair-queue ! ! interface FastEthernet0/0 ip address 1.7.73.1 255.255.255.224 duplex auto speed auto ! ! interface FastEthernet0/1 ip address 192.168.2.1 255.255.255.224 load-interval 30 duplex auto speed auto ! ip classless ip route 223.255.254.0 255.255.255.224 FastEthernet0/0 no ip http server ! ! snmp-server engineID local 0000000902000002163DB260 snmp-server packetsize 4096 snmp-server manager ! voice-port 1/0:0 ! dial-peer cor custom ! ! dial-peer voice 5 pots destination-pattern 777... port 1/0:0 prefix 777 ! ! dial-peer voice 100 voatm destination-pattern 888.... session target atm0/0 pvc 0/72 ! ! line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login ! end

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-15

Appendix A NM-AIC-64, Contact Closure NetworkConfiguration Examples

Configuration Examples

NM-AIC-64, Contact Closure NetworkConfiguration Examples

The following examples are documented below:

AIC IP Address Configuration Example, page A-16 IP Route to the AIC Configuration Examples, page A-20
With an Unnumbered IP Address, page A-20 Without an Unnumbered IP Address, page A-21

AIC CLI Configuration for Alarms, page A-22

AIC IP Address Configuration Example

The following example shows a Cisco 3600 router configured for AIC IP address:
version 12.2 no service single-slot-reload-enable service tcp-keepalives-in service tcp-keepalives-out service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 3600-top ! logging rate-limit console 10 except errors ! memory-size iomem 15 ip subnet-zero ! ! no ip finger no ip domain-lookup ip host moe 172.31.10.2 ip host mickey 10.1.1.2 ! no ip dhcp-client network-discovery frame-relay switching x25 routing ! ! call-history-mib max-size 50 ! interface Ethernet0/0 ip address 10.5.37.13 255.255.0.0 ip helper-address 223.255.254.254 no keepalive half-duplex ! interface Serial0/0 ip address 10.5.5.1 255.255.255.0 encapsulation frame-relay no ip mroute-cache clockrate 500000 frame-relay class voice-vc frame-relay traffic-shaping frame-relay map ip 10.5.5.2 990 broadcast frame-relay interface-dlci 990 frame-relay intf-type dce

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-16

OL-1957-04

Appendix A

Configuration Examples NM-AIC-64, Contact Closure NetworkConfiguration Examples

! interface Ethernet0/1 no ip address half-duplex no cdp enable ! interface Serial0/1 ip address 10.11.11.1 255.255.255.0 encapsulation frame-relay no ip mroute-cache clockrate 256000 frame-relay class voice-vc frame-relay traffic-shaping frame-relay interface-dlci 991 frame-relay intf-type dce ! interface Serial1/0 ip address negotiated ! router mobile ! ip kerberos source-interface any ip classless ip route 223.255.254.254 255.255.255.255 10.5.0.1 ip route 223.255.254.254 255.255.255.255 Ethernet0/0 no ip http server ! ! map-class frame-relay voice-vc frame-relay cir 800000 frame-relay bc 512000 no frame-relay adaptive-shaping frame-relay fair-queue frame-relay voice bandwidth 500000 frame-relay fragment 100 frame-relay ip rtp priority 16384 16383 512 ! map-class frame-relay fr1 frame-relay cir 1000000 frame-relay bc 1000 no frame-relay adaptive-shaping frame-relay fair-queue frame-relay voice bandwidth 1000000 frame-relay fragment 100 ! map-class frame-relay voice-vc2 frame-relay cir 800000 frame-relay bc 512000 no frame-relay adaptive-shaping frame-relay voice bandwidth 800000 ! map-class frame-relay voice-data access-list 1 deny 192.200.1.20 access-list 2 deny 10.10.1.10 dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit ! snmp-server packetsize 4096 snmp-server manager ! alarm-interface 1 ip address 10.4.3.2 call rsvp-sync !

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-17

Appendix A NM-AIC-64, Contact Closure NetworkConfiguration Examples

Configuration Examples

mgcp modem passthrough voip mode ca no mgcp timer receive-rtcp ! mgcp profile default ! dial-peer cor custom ! dial-peer voice 1 pots destination-pattern 3 direct-inward-dial forward-digits all ! dial-peer voice 100 voip shutdown destination-pattern 3 session target ipv4:10.2.81.1 playout-delay maximum 300 ! dial-peer voice 2 pots shutdown destination-pattern 3002 ! dial-peer voice 3 pots shutdown destination-pattern 3003 ! dial-peer voice 4 pots shutdown destination-pattern 3004 ! dial-peer voice 2000 voip shutdown destination-pattern 2... session target ipv4:5.5.5.2 playout-delay maximum 300 ! dial-peer voice 110 voip shutdown destination-pattern 1... session target ipv4:10.2.83.30 playout-delay maximum 300 ! dial-peer voice 922 pots shutdown destination-pattern 9.. ! dial-peer voice 22 pots shutdown destination-pattern 22 ! dial-peer voice 6001 pots shutdown destination-pattern 6001 ! dial-peer voice 333 voip shutdown destination-pattern 1 session target ipv4:10.2.79.55 playout-delay maximum 300 ! dial-peer voice 200 vofr shutdown destination-pattern 1 !

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-18

OL-1957-04

Appendix A

Configuration Examples NM-AIC-64, Contact Closure NetworkConfiguration Examples

dial-peer voice 7001 pots shutdown destination-pattern 7001 ! dial-peer voice 5000 voip shutdown destination-pattern 5... session target ipv4:10.11.11.2 playout-delay maximum 300 ! dial-peer voice 20 voip shutdown destination-pattern 1 session target ipv4:10.11.11.2 playout-delay maximum 300 ! dial-peer voice 2001 voip preference 2 shutdown destination-pattern 2... session target ipv4:10.2.79.7 playout-delay maximum 300 ! dial-peer voice 1000 voip destination-pattern 1... session target ipv4:10.2.81.6 playout-delay maximum 300 no vad ! dial-peer voice 1001 voatm shutdown destination-pattern 1... ! dial-peer voice 1100 vofr shutdown destination-pattern 1... session target Serial0/0 990 no vad ! gateway ! gateway ! gatekeeper shutdown ! ! line con 0 exec-timeout 0 0 transport input none line 33 no exec transport preferred none transport input telnet transport output none stopbits 1 line aux 0 line vty 0 4 login ! end

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-19

Appendix A NM-AIC-64, Contact Closure NetworkConfiguration Examples

Configuration Examples

IP Route to the AIC Configuration Examples

Following examples show the configuration of an IP route to the AIC with an unnumbered and numbered IP address.

With an Unnumbered IP Address

The following example shows a Cisco 3660 router, with an IP route to an AIC, is configured with an unnumbered IP address:
version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname uut2-3660 ! logging rate-limit console 10 except errors no logging console ! ip subnet-zero ! ! no ip finger no ip domain-lookup ! call rsvp-sync cns event-service server ! interface FastEthernet0/0 ip address 10.2.130.2 255.255.0.0 duplex auto speed auto no cdp enable ! interface Serial5/0 ip unnumbered FastEthernet0/0 ! ip kerberos source-interface any ip classless ip route 0.0.0.0 0.0.0.0 10.2.0.1 ip route 10.2.130.102 255.255.255.255 Serial5/0 ip http server ! no cdp run ! alarm-interface 5 ip address 10.2.130.102 ! dial-peer cor custom ! ! ! line con 0 exec-timeout 0 0 transport input none line 161 no exec transport preferred none transport input telnet

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-20

OL-1957-04

Appendix A

Configuration Examples NM-AIC-64, Contact Closure NetworkConfiguration Examples

transport output none stopbits 1 line aux 0 line vty 0 4 password lab login ! end

Without an Unnumbered IP Address

The following example shows a Cisco 2621 router configured without an unnumbered IP address:
uut5-2621#s run Building configuration... Current configuration :1318 bytes ! version 12.2 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname uut5-2621 ! logging rate-limit console 10 except errors no logging console ! ip subnet-zero ! no ip finger no ip domain-lookup ! no ip dhcp-client network-discovery ! interface FastEthernet0/0 ip address 10.2.130.5 255.255.0.0 duplex auto speed auto no cdp enable ! interface Serial1/0 ip address 172.128.12.1 255.255.255.252 ! router rip network 10.0.0.0 ! ip kerberos source-interface any ip classless ip route 0.0.0.0 0.0.0.0 10.2.0.1 no ip http server ! no cdp run ! snmp-server packetsize 4096 snmp-server manager ! ! alarm-interface 1 ip address 172.128.12.2 call rsvp-sync

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-21

Appendix A NM-AIC-64, Contact Closure NetworkConfiguration Examples

Configuration Examples

! dial-peer cor custom ! line con 0 exec-timeout 0 0 transport input none line 33 no exec transport preferred none transport input telnet transport output none stopbits 1 line aux 0 line vty 0 4 password lab login ! no scheduler allocate ! end

AIC CLI Configuration for Alarms

These examples are output from the show alarm config # command.

Discrete Alarm
description:west door normally closed normal state description:door closed alarm state description:door open SNMP trap:enabled

Analog Alarm Monitoring Current

description:thermostat high-high state description:very hot high state description:hot normal state description:just right low state description:cold low-low state description:very cold current-loop -5.2 5.4 15.0 25.0 35.1 45.6 SNMP trap:enabled

Analog Alarm Monitoring Current Configured as a Discrete

description:east door configured as discrete normal state description:door closed alarm description:door open current-loop 0.0 3.2 5.9

SNMP trap:enabled

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-22

OL-1957-04

Appendix A

Configuration Examples Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
The following configuration allows remote LANs and standalone remote users with modems to dial in to a central site. The following configuration example shows a Cisco 3640 router with the following hardware configuration:

One 2-port ISDN-PRI network module installed in slot 1 One digital modem network module installed in slot 2 and slot 3 One 1-port Ethernet network module installed in slot 0

Note

Each MICA digital modem card has its own group async configuration. Additionally, a single range of async lines is used for each modem card. For additional interface numbering information, refer to the Digital Modem Network Module Configuration Note.
! version 11.2 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption no service udp-small-servers no service tcp-small-servers ! hostname NAS ! aaa new-model aaa authentication login default local aaa authentication login console enable aaa authentication login vty local aaa authentication login dialin local aaa authentication ppp default local aaa authentication ppp dialin if-needed local enable secret cisco ! username admin password cisco username remotelan1 password dialpass1 username remotelan2 password dialpass2 username PCuser1 password dialpass3 username PCuser2 password dialpass4 async-bootp dns-server 10.1.3.1 10.1.3.2 isdn switch-type primary-5ess ! controller T1 1/0 framing esf clock source line linecode b8zs pri-group timeslots 1-24 ! controller T1 1/1 framing esf clock source line linecode b8zs pri-group timeslots 1-24 ! interface Loopback0 ip address 10.1.2.254 255.255.255.0

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-23

Appendix A Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

Configuration Examples

! interface Ethernet0/0 ip address 10.1.1.10 255.255.255.0 ip summary address eigrp 10 10.1.2.0 255.255.255.0 ! interface Serial 1/0:23 no ip address encapsulation ppp no keepalive isdn incoming-voice modem dialer rotary-group 0 dialer-group 1 no fair-queue no cdp enable ! interface Serial 1/1:23 no ip address encapsulation ppp no keepalive isdn incoming-voice modem dialer rotary-group 0 dialer-group 1 no fair-queue no cdp enable ! interface Group-Async1 ip unnumbered Loopback0 encapsulation ppp async mode interactive peer default ip address pool dialin_pool no cdp enable ppp authentication chap pap dialin group-range 65 88 ! interface Group-Async2 ip unnumbered Loopback0 encapsulation ppp async mode interactive peer default ip address pool dialin_pool no cdp enable ppp authentication chap pap dialin group-range 97 120 ! interface Dialer0 ip unnumbered Loopback0 no ip mroute-cache encapsulation ppp peer default ip address pool dialin_pool dialer in-band dialer-group 1 no fair-queue no cdp enable ppp authentication chap pap dialin ppp multilink ! router eigrp 10 network 10.0.0.0 passive-interface Dialer0 no auto-summary ! ip local pool dialin_pool 10.1.2.1 10.1.2.50 ip default-gateway 10.1.1.1 ip classless !

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-24

OL-1957-04

Appendix A

Configuration Examples Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

dialer-list 1 protocol ip permit ! line con 0 login authentication console line 65 88 autoselect ppp autoselect during-login login authentication dialin modem DialIn line 97 120 autoselect ppp autoselect during-login login authentication dialin modem DialIn line aux 0 login authentication console line vty 0 4 login authentication vty transport input telnet rlogin ! end

Configuration in CPE Mode Example

The following example shows a G.SHDSL configuration of VoATM over AAL2, operating in customer premises equipment (CPE) mode, on a Cisco 2600 series router. This router in CPE mode can be linked to either a DSLAM or to another router that is configured to operate in central office (CO) mode.
Router# version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname host1 ! memory-size iomem 10 voice-card 1 ! ip subnet-zero ip host host2 225.255.255.224 ! no mgcp timer receive-rtcp call rsvp-sync ! ! controller T1 1/0 framing esf linecode b8zs ds0-group 0 timeslots 1 type e&m-wink-start ds0-group 1 timeslots 2 type e&m-wink-start . . . ds0-group 23 timeslots 24 type e&m-wink-start ! controller T1 1/1 framing esf linecode b8zs !

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-25

Appendix A Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

Configuration Examples

interface Ethernet0/0 ip address 209.165.202.128 255.255.255.224 half-duplex no cdp enable ! interface Serial0/0 no ip address shutdown ! interface ATM0/1 ip address 209.165.201.1 255.255.255.224 dsl operating-mode gshdsl symmetric annex A dsl equipment-type cpe dsl linerate auto load-interval 30 atm vc-per-vp 256 no atm ilmi-keepalive pvc 10/100 vbr-rt 672 672 512 encapsulation aal2 ! pvc 10/200 protocol ip 209.165.202.159 broadcast encapsulation aal5snap ! no fair-queue ! interface Ethernet0/1 no ip address shutdown ! ip classless ip route 209.165.202.128 255.255.255.224 Ethernet0/0 no ip http server ! ! snmp-server engineID local 000000090200003080477F20 snmp-server manager ! voice-port 1/0:0 local-alerting timeouts wait-release 3 connection trunk 3001 ! voice-port 1/0:1 local-alerting timeouts wait-release 3 connection trunk 3002 . . . voice-port 1/0:23 local-alerting timeouts wait-release 3 connection trunk 3024 shutdown ! dial-peer cor custom ! dial-peer voice 3001 voatm destination-pattern 3001 called-number 4001 session protocol aal2-trunk session target ATM0/1 pvc 10/100 31

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-26

OL-1957-04

Appendix A

Configuration Examples Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

codec aal2-profile ITUT 1 g711ulaw no vad ! dial-peer voice 3002 voatm destination-pattern 3002 called-number 4002 session protocol aal2-trunk session target ATM0/1 pvc 10/100 32 codec aal2-profile custom 100 g726r32 no vad ! dial-peer voice 3003 voatm destination-pattern 3003 called-number 4003 session protocol aal2-trunk session target ATM0/1 pvc 10/100 33 codec aal2-profile ITUT 7 g729abr8 no vad . . . dial-peer voice 3024 voatm destination-pattern 3024 called-number 3024 session protocol aal2-trunk session target ATM0/1 pvc 10/100 54 codec aal2-profile ITUT 7 g729abr8 no vad ! dial-peer voice 1 pots destination-pattern 4001 port 1/0:0 ! dial-peer voice 2 pots destination-pattern 4002 port 1/0:1 . . . dial-peer voice 24 pots destination-pattern 4024 port 1/0:23 ! ! line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login ! no scheduler allocate end

Configuration in CO Mode Example

The following example shows a G.SHDSL configuration of VoATM over AAL2, operating in central office (CO) mode, on a Cisco 2600 series router. This router in CO mode can be linked to another router that is configured to operate in CPE mode.
Router#

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-27

Appendix A Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

Configuration Examples

version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname host2 ! memory-size iomem 10 voice-card 1 ! ip subnet-zero ip host host2 225.255.255.224 ! no mgcp timer receive-rtcp call rsvp-sync ! ! controller T1 1/0 framing esf linecode b8zs ds0-group 0 timeslots 1 type e&m-wink-start ds0-group 1 timeslots 2 type e&m-wink-start . . . ds0-group 23 timeslots 24 type e&m-wink-start ! controller T1 1/1 framing esf linecode b8zs ! interface Ethernet0/0 ip address 209.165.202.128 255.255.255.224 half-duplex no cdp enable ! interface Serial0/0 no ip address shutdown ! interface ATM0/1 ip address 209.165.201.1 255.255.255.224 dsl operating-mode gshdsl symmetric annex A dsl equipment-type co dsl linerate auto load-interval 30 atm vc-per-vp 256 no atm ilmi-keepalive pvc 10/100 vbr-rt 672 672 512 encapsulation aal2 ! pvc 10/200 protocol ip 209.165.202.159 broadcast encapsulation aal5snap ! no fair-queue ! interface Ethernet0/1 no ip address shutdown ! ip classless ip route 209.165.202.128 255.255.255.224 Ethernet0/0

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-28

OL-1957-04

Appendix A

Configuration Examples Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

no ip http server ! ! snmp-server engineID local 000000090200003080477F20 snmp-server manager ! voice-port 1/0:0 local-alerting timeouts wait-release 3 connection trunk 3001 ! voice-port 1/0:1 local-alerting timeouts wait-release 3 connection trunk 3002 . . . voice-port 1/0:23 local-alerting timeouts wait-release 3 connection trunk 3024 shutdown ! dial-peer cor custom ! dial-peer voice 3001 voatm destination-pattern 3001 called-number 4001 session protocol aal2-trunk session target ATM0/1 pvc 10/100 31 codec aal2-profile ITUT 1 g711ulaw no vad ! dial-peer voice 3002 voatm destination-pattern 3002 called-number 4002 session protocol aal2-trunk session target ATM0/1 pvc 10/100 32 codec aal2-profile custom 100 g726r32 no vad ! dial-peer voice 3003 voatm destination-pattern 3003 called-number 4003 session protocol aal2-trunk session target ATM0/1 pvc 10/100 33 codec aal2-profile ITUT 7 g729abr8 no vad . . . dial-peer voice 3024 voatm destination-pattern 3024 called-number 3024 session protocol aal2-trunk session target ATM0/1 pvc 10/100 54 codec aal2-profile ITUT 7 g729abr8 no vad ! dial-peer voice 1 pots destination-pattern 4001 port 1/0:0 !

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

A-29

Appendix A Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls

Configuration Examples

dial-peer voice 2 pots destination-pattern 4002 port 1/0:1 . . . dial-peer voice 24 pots destination-pattern 4024 port 1/0:23 ! ! line con 0 exec-timeout 0 0 transport input none line aux 0 line vty 0 4 login ! no scheduler allocate end

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

A-30

OL-1957-04

A P P E N D I X

Formatting the Compact Flash Memory Cards

This appendix describes how to format the compact Flash memory into a Class B Flash file system, known as the low-end file system (LEFS), or into a Class C Flash file system, which is similar to DOS. It also describes how to perform file and directory operations in each file system.

Formatting Procedures for Compact Flash Memory Cards

The following sections describe formatting procedures for internal and external compact Flash memory cards.

Formatting Procedures
Cisco recommends that you erase (Class B) or format (Class C) new compact Flash memory cards to initialize them with either a Class B or Class C Flash file system. This ensures proper formatting and enables the ROM monitor to recognize and boot the Flash. The Class B Flash file system is also known as the low end file system (LEFS). The Class C Flash file system is similar to the standard DOS file system.
Note

A compact Flash memory card formatted with the standard DOS file system does not support booting from the ROM monitor.

Determining the File System on a Compact Flash Memory Card

To determine the file system of an external compact Flash memory card, enter the show slot0: all command. To determine the file system of an internal compact Flash memory card, enter the show flash: all command.

If geometry and format information is not displayed, the card is formatted with a Class B Flash file system. If geometry and format information is displayed, the card is formatted with a Class C Flash file system.

The following examples show outputs for Class B and Class C Flash file systems:

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

B-1

Appendix B Formatting Procedures for Compact Flash Memory Cards

Formatting the Compact Flash Memory Cards

External Card with Class B Flash File System:

The geometry and format information is not displayed for this format.
Router#show slot0: all Partition Mode 1 Size 31360K Used 6502K Free 24857K Bank-Size 0K State Read/Write Copy Direct

Slot0 CompactFlash directory: File Length Name/status addr fcksum ccksum 1 6658376 c3725-i-mz 0x40 0xE0FF 0xE0FF [6658440 bytes used, 25454200 available, 32112640 total] 31360K bytes of ATA Slot0 CompactFlash (Read/Write) Chip information NOT available.

External Card with Class C Flash File System:

The geometry and format information is displayed in this format.

Router#show slot0:all -#- --length-- -----date/time------ path 1 6658376 Mar 01 1993 04:27:46 c3725-i-mz 25268224 bytes available (6664192 bytes used) ******** ATA Flash Card Geometry/Format Info ******** ATA CARD GEOMETRY Number of Heads: Number of Cylinders Sectors per Cylinder Sector Size Total Sectors ATA CARD FORMAT Number of FAT Sectors Sectors Per Cluster Number of Clusters Number of Data Sectors Base Root Sector Base FAT Sector Base Data Sector

4 490 32 512 62720

31 8 7796 62560 155 93 187

Internal Card with Class B Flash File System:

The geometry and format information is not displayed for this format.
Router# show flash: all Partition Mode 1 Direct Size 125184K Used 20390K Free 104793K Bank-Size 0K State Read/Write Copy

System CompactFlash directory: File Length Name/status addr fcksum ccksum 1 6658376 c3725-i-mz 0x40 0xE0FF 0xE0FF 2 14221136 c3631-telcoent-mz

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

B-2

OL-1957-04

Appendix B

Formatting the Compact Flash Memory Cards Formatting Procedures for Compact Flash Memory Cards

0x6599C8 0x5C3D 0x5C3D [20879640 bytes used, 107308776 available, 128188416 total] 125184K bytes of ATA System CompactFlash (Read/Write) Chip information NOT available.

Internal card with Class C Flash file system:

The geometry and format information is displayed in this format.

Router#show flash: all -#- --length-- -----date/time------ path 1 6658376 Mar 01 1993 04:27:46 c3725-i-mz 25268224 bytes available (6664192 bytes used) ******** ATA Flash Card Geometry/Format Info ******** ATA CARD GEOMETRY Number of Heads: Number of Cylinders Sectors per Cylinder Sector Size Total Sectors ATA CARD FORMAT Number of FAT Sectors Sectors Per Cluster Number of Clusters Number of Data Sectors Base Root Sector Base FAT Sector Base Data Sector

4 490 32 512 62720

31 8 7796 62560 155 93 187

Formatting Compact Flash Memory as a Class B Flash File System

Use these formatting commands to:

Format compact Flash memory cards with a Class B Flash file system (LEFS) Remove the files from a compact Flash memory card previously formatted with a Class B Flash file system

For external compact Flash memory cards, enter the erase slot0: command. For internal compact Flash memory cards, enter the erase flash: command. The following example shows output for formatting an external compact Flash memory card with a Class B Flash file system:
Router# erase slot0: Erasing the slot0 filesystem will remove all files! Continue? [confirm] Current DOS File System flash card in slot0: will be formatted into Low End File System flash card! Continue? [confirm] Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee ...erased Erase of slot0: complete

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

B-3

Appendix B File and Directory Operations

Formatting the Compact Flash Memory Cards

Formatting Compact Flash Memory as a Class C File System

Use these formatting commands to:

Format compact Flash memory cards with a Class C Flash file system Remove the files from a compact Flash memory card previously formatted with a Class C Flash file system

For external compact Flash memory cards, enter the format slot0: command. For internal compact Flash memory cards, enter the format flash: command. The following example shows output for formatting an internal compact Flash memory card with a Class C Flash file system:
Router# format flash: Format operation may take a while. Continue? [confirm] Format operation will destroy all data in "flash:". Continue? [confirm] Enter volume ID (up to 64 chars)[default flash]: Current Low End File System flash card in flash will be formatted into DOS File System flash card! Continue? [confirm] Format:Drive communication & 1st Sector Write OK... Writing Monlib sectors ................................................................... Monlib write complete .. Format:All system sectors written. OK... Format:Total sectors in formatted partition:250592 Format:Total bytes in formatted partition:128303104 Format:Operation completed successfully. Format of flash complete

File and Directory Operations

The following sections describe file and directory operations for internal and external Cisco Flash memory cards. File and directory operations vary according to the formatted file systemClass B or Class C.

Operations for Use With Class B Flash File System

The following file operations are useful for compact Flash memory cards formatted with a Class B Flash file system.
Copy Files

To copy files to another location, enter the copy {flash: | slot0:} command. The following example shows output for copying a Cisco IOS file from an internal compact Flash memory card (flash:) to an external compact Flash memory card (slot0:):
Router# copy flash:c3725-i-mz.tmp slot0: Destination filename [c3725-i-mz.tmp]? Erase slot0:before copying? [confirm]nCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

B-4

OL-1957-04

Appendix B

Formatting the Compact Flash Memory Cards File and Directory Operations

CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC Verifying checksum... OK (0xC68E) 6458584 bytes copied in 67.788 secs (96396 bytes/sec)

The following example shows output for copying a configuration file to the startup configuration in an internal compact Flash memory card (flash:):
Router# copy flash:my-config1 startup-config Destination filename [startup-config]? [OK] 517 bytes copied in 4.188 secs (129 bytes/sec)

The following example shows output for copying a configuration file to the running configuration in an internal compact Flash memory card (flash:):
Router# copy flash:my-config2 running-config Destination filename [running-config]? 709 bytes copied in 0.72 secs

Display the Contents of a Compact Flash Memory Card

To display the contents (directories and files) of a compact Flash memory card formatted with a Class B Flash file system, enter the dir {flash: | slot0:} command or the show {flash: | slot0:} command. The following example shows output for displaying the contents of an internal compact Flash memory card using the dir flash: command:
Router# dir flash: Directory of flash:/ 1 2 3 -rw-rw-rw5190020 6458584 16535740 <no date> <no date> <no date> c3631-i-mz c3725-i-mz c3631-telcoent-mz

128450560 bytes total (100266024 bytes free)

The following example shows output for displaying the contents of an external compact Flash memory card using the show slot0: command:
Router# show slot0: System CompactFlash directory: File Length Name/status 1 5190020 c3631-i-mz 2 6458584 c3725-i-mz 3 16535740 c3631-telcoent-mz [28184536 bytes used, 100266024 available, 128450560 total] 125440K bytes of ATA System CompactFlash (Read/Write)

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

B-5

Appendix B File and Directory Operations

Formatting the Compact Flash Memory Cards

Delete Files from Compact Flash Memory

To delete a file from compact Flash memory, enter the delete {flash: | slot0:} command, followed by the squeeze {flash: | slot0:} command. When a file is deleted in the Class B Flash file system, the memory space occupied by the deleted file is not released until you enter the squeeze {flash: | slot0:} command. Although the memory space once occupied by the deleted file remains, the deleted file cannot be recovered. To release the memory space occupied by a deleted file, enter the squeeze {flash: | slot0:} command.
Note

The dir {flash: | slot0:} command does not show deleted files; the show {flash: | slot0:} command shows all files, including any deleted files if the squeeze {flash: | slot0:} command has not been entered. The following example shows output for deleting a Cisco IOS file from an external compact Flash memory card, and then releasing the memory space originally occupied by the file:
Router# dir slot0: Directory of slot0:/ 1 2 -rw-rw6458208 6458208 <no date> <no date> c3725-i-mz.tmp c3725-i-mz

16056320 bytes total (3139776 bytes free) Router# delete slot0:c3725-i-mz.tmp Delete filename [c3725-i-mz.tmp]? Delete slot0:c3725-i-mz.tmp? [confirm] Router# dir slot0: Directory of slot0:/ 2 -rw6458208 <no date> c3725-i-mz

16056320 bytes total (3139776 bytes free) Router# show slot0: Slot0 CompactFlash directory: File Length Name/status 1 6458208 c3725-i-mz.tmp [deleted] 2 6458208 c3725-i-mz [12916544 bytes used, 3139776 available, 16056320 total] 15680K bytes of ATA Slot0 CompactFlash (Read/Write) Router# squeeze slot0: Squeeze operation may take a while. Continue? [confirm] squeeze in progress... sssssssssssssssssssssssseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee Rebuild file system directory... Squeeze of slot0 complete

Display File Content

To display the content of a file in compact Flash memory, use the more {flash: | slot0:} command. The following example shows output from the more {flash: | slot0:} command on an external Cisco Flash memory card:
Router# more slot0:c3725-i-mz 00000000: 7F454C46 01020100 00000000 00000000 .ELF .... .... ....

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

B-6

OL-1957-04

Appendix B

Formatting the Compact Flash Memory Cards File and Directory Operations

00000010: 00020061 00000020: 00000054 00000030: 00050008 00000040: 80008000 00000050: 0000011C 00000060: 80008000 00000070: 00000000 00000080: 00000001 00000090: 00000700 000000A0: 00000000 000000B0: 8000C700 000000C0: 00000000 000000D0: 00000001 000000E0: 00000020 000000F0: 00000000 00000100: 8000CAA0 00000110: 00000000 00000120: 679C4A80 00000130: AC3FC710 00000140: AC25C718 00000150: AC27C720 00000160: AC31C728 --More-- q

00000001 20000001 00000001 00628A44 0000001B 0000011C 00000008 00000002 00000000 00000029 0000481C 00000004 10000003 00000000 0000002F 00004BBC 00000008 3C018001 3C018001 3C018001 3C018001 3C018001

80008000 00340020 0000011C 00650EEC 00000001 00004000 00000000 8000C000 00000000 00000001 00000380 00000000 8000CA80 00000000 00000001 00623FA4 00000000 AC3DC70C AC24C714 AC26C71C AC30C724 AC32C72C

00000034 00010028 80008000 00000007 00000006 00000000 00000021 0000411C 00000004 00000003 00000000 0000002F 00004B9C 00000008 10000003 00000000 3C1C8001 3C018001 3C018001 3C018001 3C018001 3C018001

...a ...T .... .... .... .... .... .... .... .... ..G. .... .... ... .... ..J .... g.J. ,?G. ,%G. ,'G ,1G(

.... ... .... .b.D .... .... .... .... .... ...) ..H. .... .... .... .../ ..K< .... <... <... <... <... <...

.... .4. .... .e.l .... ..@. .... ..@. .... .... .... .... ..J. .... .... .b?$ .... ,=G. ,$G. ,&G. ,0G$ ,2G,

...4 ...( .... .... .... .... ...! ..A. .... .... .... .../ ..K. .... .... .... <... <... <... <... <... <...

Operations for Use with Class C Flash File System

The following file and directory operations are useful for compact Flash memory cards formatted with a Class C Flash file system.

File Operations for Class C Flash File System

Copy Files

To copy files to another location, enter the copy {flash: | slot0:} command. The following example shows output for copying a Cisco IOS file from an external compact Flash memory card to an internal compact Flash memory card:
Router# copy slot0:c3725-i-mz.tmp flash: Destination filename [c3725-i-mz.tmp]? CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC 6458584 bytes copied in 202.940 secs (31973 bytes/sec)

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

B-7

Appendix B File and Directory Operations

Formatting the Compact Flash Memory Cards

The following example shows output for copying a configuration file to the startup configuration in an internal compact Flash memory card ( flash:):
Router# copy flash:my-config1 startup-config Destination filename [startup-config]? [OK] 517 bytes copied in 4.188 secs (129 bytes/sec)

The following example shows output for copying a configuration file to the running configuration in an internal compact Flash memory card ( flash:):
Router# copy flash:my-config2 running-config Destination filename [running-config]? 709 bytes copied in 0.72 secs

Display the Contents of a Compact Flash Memory Card

To display the contents (directories and files) of a compact Flash memory card formatted with a Class C Flash file system, use the dir{flash: | slot0:} or show {flash: | slot0:} command. The following examples show outputs for displaying the contents of an external compact Flash memory card with a Class C Flash file system:
Router# show slot0: -#- --length-- -----date/time-----1 6658376 Mar 01 1993 00:29:52 2 2124 Mar 01 1993 00:34:38 3 2622 Mar 01 1993 00:34:44 path c3725-i-mz running-config startup-config

25260032 bytes available (6672384 bytes used) Router# dir slot0: Directory of slot0:/ 3 1579 -rw-rw6455048 6458584 Mar 01 2001 00:04:06 Mar 01 2001 00:24:38 c3725-i-mz c3725-i-mz.new

15912960 bytes total (2998272 bytes free)

Display Geometry and Format Information

To display the geometry and format information of a compact Flash memory card formatted with a Class C Flash file system, use the show {flash: | slot0:} filesys command. The following example shows output for displaying the geometry and format information of an external Cisco Flash memory card:
Router# show slot0: filesys ******** ATA Flash Card Geometry/Format Info ******** ATA CARD GEOMETRY Number of Heads: Number of Cylinders Sectors per Cylinder Sector Size Total Sectors ATA CARD FORMAT Number of FAT Sectors

4 490 32 512 62720

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

B-8

OL-1957-04

Appendix B

Formatting the Compact Flash Memory Cards File and Directory Operations

Sectors Per Cluster Number of Clusters Number of Data Sectors Base Root Sector Base FAT Sector Base Data Sector

8 7796 62560 155 93 187

Delete Files from Compact Flash Memory

To delete a file from a compact Flash memory card, use the delete {flash: | slot0:} command. The following example shows output for deleting a Cisco IOS file from an internal compact Flash memory card:
Router# delete flash:c3725-i-mz.tmp Delete filename [c3725-i-mz.tmp]? Delete flash:c3725-i-mz.tmp? [confirm] Router# dir flash: Directory of flash:/ No files in directory 128094208 bytes total (128094208 bytes free)

Rename a File

To rename a file in a compact Flash memory card, use the rename {flash: | slot0:} command. The following example shows output for renaming a Cisco IOS file in an internal compact Flash memory card:
Router# dir flash: Directory of flash:/ 3 1580 -rw-rw6458388 6462268 Mar 01 1993 00:00:58 Mar 06 1993 06:14:02 c3725-i-mz.tmp c3725-i-mz.3600ata

63930368 bytes total (51007488 bytes free) Router# rename flash:c3725-i-mz.tmp flash:c3725-i-mz Destination filename [c3725-i-mz]? Router# dir flash: Directory of flash:/ 1580 3 -rw-rw6462268 6458388 Mar 06 1993 06:14:02 Mar 01 1993 00:01:24 c3725-i-mz.3600ata c3725-i-mz

63930368 bytes total (51007488 bytes free)

Display File Content

To display the content of a file in a compact Flash memory card, use the more {flash: | slot0:} command. The following example shows output from the more {flash: | slot0:} command on an internal Compact Flash card:
Router# more flash:c3725-i-mz.tmp 00000000: 7F454C46 01020100 00000000 00000000 00000010: 00020061 00000001 80008000 00000034 .ELF .... .... .... ...a .... .... ...4

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

B-9

Appendix B File and Directory Operations

Formatting the Compact Flash Memory Cards

00000020: 00000054 00000030: 00050008 00000040: 80008000 00000050: 0000011C 00000060: 80008000 00000070: 00000000 00000080: 00000001 00000090: 00000700 000000A0: 00000000 000000B0: 8000C700 000000C0: 00000000 000000D0: 00000001 000000E0: 00000020 000000F0: 00000000 00000100: 8000CAA0 00000110: 00000000 00000120: 679C4A80 00000130: AC3FC710 00000140: AC25C718 00000150: AC27C720 00000160: AC31C728 --More-- q

20000001 00000001 00628A44 0000001B 0000011C 00000008 00000002 00000000 00000029 0000481C 00000004 10000003 00000000 0000002F 00004BBC 00000008 3C018001 3C018001 3C018001 3C018001 3C018001

00340020 0000011C 00650EEC 00000001 00004000 00000000 8000C000 00000000 00000001 00000380 00000000 8000CA80 00000000 00000001 00623FA4 00000000 AC3DC70C AC24C714 AC26C71C AC30C724 AC32C72C

00010028 80008000 00000007 00000006 00000000 00000021 0000411C 00000004 00000003 00000000 0000002F 00004B9C 00000008 10000003 00000000 3C1C8001 3C018001 3C018001 3C018001 3C018001 3C018001

...T .... .... .... .... .... .... .... .... ..G. .... .... ... .... ..J .... g.J. ,?G. ,%G. ,'G ,1G(

... .... .b.D .... .... .... .... .... ...) ..H. .... .... .... .../ ..K< .... <... <... <... <... <...

.4. .... .e.l .... ..@. .... ..@. .... .... .... .... ..J. .... .... .b?$ .... ,=G. ,$G. ,&G. ,0G$ ,2G,

...( .... .... .... .... ...! ..A. .... .... .... .../ ..K. .... .... .... <... <... <... <... <... <...

Directory Operations for Class C Flash File System

Create a New Directory

To create a directory in compact Flash memory, use the mkdir {flash: | slot0:} command. The following example shows output for first displaying the contents of an internal compact Flash card, and then creating a directory named config and a subdirectory named test-config:
Router# dir flash: Directory of flash:/ 3 -rw6458208 Mar 01 1993 00:04:08 c3725-i-mz.tmp

128094208 bytes total (121634816 bytes free) Router# mkdir flash:/config Create directory filename [config]? Created dir flash:/config Router# mkdir flash:/config/test-config Create directory filename [/config/test-config]? Created dir flash:/config/test-config Router# dir flash: Directory of flash:/ 3 -rw1580 drw6458208 0 Mar 01 1993 00:04:08 c3725-i-mz.tmp Mar 01 1993 23:48:36 config

128094208 bytes total (121626624 bytes free) Router# cd flash:/config Router# dir flash: Directory of flash:/config/ 1581 drw0 Mar 01 1993 23:50:08 test-config

128094208 bytes total (121626624 bytes free)

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

B-10

OL-1957-04

Appendix B

Formatting the Compact Flash Memory Cards File and Directory Operations

Remove a Directory

To remove a directory from compact Flash memory, use the rmdir {flash: | slot0:} command. Before you can remove a directory, all files and subdirectories must be removed from the directory. The following example shows output for displaying the contents of an internal compact Flash card, then removing the subdirectory named test-config:
Router# dir flash: Directory of flash:/config/ 1581 drw0 Mar 01 1993 23:50:08 test-config

128094208 bytes total (121626624 bytes free) Router# rmdir flash:/config/test-config Remove directory filename [/config/test-config]? Delete flash:/config/test-config? [confirm] Removed dir flash:/config/test-config Router# dir flash: Directory of flash:/config/ No files in directory 128094208 bytes total (121630720 bytes free)

Enter a Directory and Determine Which Directory You Are In

To enter a directory in compact Flash memory, use the cd command. To determine which directory you are in, use the pwd command. If you enter only cd, the router will enter the default home directory, which is flash:/. The following example shows output for the following actions:

Entering the home directory of a compact Flash memory card in an internal slot (flash:/) Verifying that you are in the home directory Displaying the contents of the home directory Entering the /config directory Verifying that you are in the /config directory Entering the home directory of a compact Flash memory card in an external slot (slot0:/) Verifying that you are in the slot0:/ directory Returning to the home directory (flash:/) Verifying that you are in the home directory

Router# cd Router# pwd flash: Router# dir Directory of flash:/ 3 1580 -rwdrw6458208 0 Mar 01 1993 00:04:08 Mar 01 1993 23:48:36 c3725-i-mz.tmp config

128094208 bytes total (121630720 bytes free)

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

B-11

Appendix B

Formatting the Compact Flash Memory Cards

Router# cd config Router# pwd flash:/config/ Router# cd slot0: Router# pwd slot0:/ Router# cd Router# pwd flash:

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

B-12

OL-1957-04

A P P E N D I X

Using the ROM Monitor

This appendix describes the ROM monitor (also called the bootstrap program), which is the firmware that runs when you power on or restart the Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series router. During normal operation, the ROM monitor helps to initialize the processor hardware and boot the operating system software. You can also use the ROM monitor to help you isolate or rule out hardware problems encountered when installing your router. This appendix contains the following sections:

Entering the ROM Monitor Mode, page C-1 ROM Monitor Commands, page C-2 ROM Monitor Syntax Conventions, page C-3 Command Descriptions, page C-3 Procedures for Recovering Boot and System Images, page C-8

Entering the ROM Monitor Mode

To use the ROM monitor, you must have access to the console port. See the Cisco 2600 Series Cabling and Setup Quick Start Guide for information on connecting the console cable. To enter ROM monitor mode, do the following:

Configure
Command or Action
Step 1 2600> reload Step 2 Press the Break key during the first 60 seconds while

Purpose Restarts the router. Forces the router to stop booting and enter the ROM monitor mode.

the system is starting up

Verify
To verify that you are in the ROM monitor mode, check that the prompt displayed on your screen is the ROM monitor mode prompt:
rommon # >

The # is the line number and increases incrementally at each prompt.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

C-1

Appendix C Entering the ROM Monitor Mode

Using the ROM Monitor

Tip

From the Cisco IOS software, you can configure the router to automatically enter the ROM monitor mode the next time the router boots by setting virtual configuration register bits 3, 2, 1, and 0 to zero. From the console, enter the following configuration command:
configuration-register 0x0

The new configuration register value, 0x0, is effective after the router is rebooted with the reload command. The router remains in the ROM monitor and does not boot the operating system. As long as the configuration register value remains 0x0, you must manually boot the operating system from the console. Refer to the boot command in the section Command Descriptions later in this appendix.

ROM Monitor Commands

Enter ? or help at the ROM monitor mode prompt to display a list of available commands. For example:
rommon 1 > alias boot break confreg cont context cookie dev dir dis dnld frame help history meminfo repeat reset set stack sync sysret tftpdnld unalias unset xmodem rommon 2 > ? set and display aliases command boot up an external process set/show/clear the breakpoint configuration register utility continue executing a downloaded image display the context of a loaded image display contents of cookie PROM in hex list the device table list files in the file system display instruction stream serial download a program module print out a selected stack frame monitor builtin command help monitor command history main memory information repeat a monitor command system reset display the monitor variables produce a stack trace write monitor environment to NVRAM print out info from last system return tftp image download unset an alias unset a monitor variable x/ymodem image download

Note

You can abort any command by pressing the Break key at the console.

Note

The command tftpdnld is present in the Cisco 2600 series routers only.

Note

The command upgrade rom-monitor is present in the Cisco 3700 series routers only.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

C-2

OL-1957-04

Appendix C

Using the ROM Monitor Entering the ROM Monitor Mode

ROM Monitor Syntax Conventions

The ROM monitor syntax in this appendix uses the following conventions:

Square brackets [ ] denote an optional element. In the following example, the element abc is not required, but you can specify it if you choose: command [abc]

If a minus option is followed by a colon (for example, [-s:]) you must provide an argument for the option. A term in italics means that you must fill in the appropriate information. In the following example, you replace the term in italics with the interface type you are using:
command type interface

Command Descriptions
This section lists some useful ROM monitor commands. Refer to the Cisco IOS configuration guides and command references for more information on ROM monitor commands.
Note

The commands show rom-monitor, showmon, upgrade rom-monitor , upgrade rom-monitor preference, rommon-pref are present in the Cisco 3700 series routers only. The command tftpdnld is present in the Cisco 2600 series routers only.

boot or bBoots an image.

Boots from the first IOS image in flash memory. flash:[name] boots the Cisco IOS software from the flash memory. filename tftpserver boots from the specified file over the network from the specified TFTP

server. For example:

boot c2600-i-mz 172.15.19.11

filename boots from the boothelper image, because it does not recognize the device ID. This

form of the command is used to netboot the image named filename.

The Cisco 2600 series router does not have a dedicated boothelper image ([rx]boot) as used by some other Cisco routers. With the Cisco 2600 series router, the first image in flash memory is invoked as the default boothelper image anytime the ROM monitor does not recognize the device ID in the boot command. You can override the default boothelper image setting by setting the BOOTLDR Monitor environment variable to point to another image. Any system image can be used for this purpose. Options to the boot command are -x, load image but do not execute, and -v, verbose. Use the Cisco IOS commands show version and show hardware to display the source of the currently running image.

dir device:[partition:]Lists the files on the named device. For example:

rommon 8 > dir flash: File size 2229799 bytes (0x220627) Checksum 0x469e File name C2600-j-m2.113-4T

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

C-3

Appendix C Entering the ROM Monitor Mode

Using the ROM Monitor

helpDisplays a summary of ROM monitor commands (equivalent to ?). meminfoDisplays size in bytes, starting address, available range of main memory, the

starting point and size of packet memory, and size of nonvolatile memory (NVRAM). The following example shows the meminfo command:
rommon 9 > meminfo Main memory size: 32 MB. Available main memory starts at 0xa000e000, size 32704KB IO (packet) memory size: 25 percent of main memory. NVRAM size: 32KB

meminfo [-l]The meminfo command with the -l option displays supported DRAM configurations. The following example shows an example of the meminfo -l command:
rommon 10 > meminfo -l Supported memory configurations: DIMM 0 DIMM 1 ------------------4M 8M-DUAL 16M 32M-DUAL 4M 4M 4M 4M 8M-DUAL 4M 16M 4M 32M-DUAL 8M-DUAL 8M-DUAL 4M 8M-DUAL 8M-DUAL 8M-DUAL 16M 8M-DUAL 32M-DUAL 16M 16M 4M 16M 8M-DUAL 16M 16M 16M 32M-DUAL 32M-DUAL 32M-DUAL 4M 32M-DUAL 8M-DUAL 32M-DUAL 16M 32M-DUAL 32M-DUAL

reset or iResets and initializes the router, similar to power on. show rom-monitor Shows version of read-only ROMMON, and if present, the upgrade version of ROMMON. It also shows the current version of ROMMON, which version will be selected for execution when the Cisco IOS software is booted again. This command isavailable in the Cisco IOS exec mode.
showmonAvailable in the ROMMON command mode. Provides the same information as the

show rom-monitor command in the Cisco IOS exec mode.

upgrade rom-monitor <file<URL>|preference<readonly|upgrade>>Installs and reloads a new version of ROMMON in the Cisco IOS exec mode. URL refers to the path where the new ROMMON image is stored. Prompts the user to save the configuration.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

C-4

OL-1957-04

Appendix C

Using the ROM Monitor Entering the ROM Monitor Mode

upgrade rom-monitor preference<readonly|upgrade>Selects the version of ROMMON to

be loaded the next time the router is reloaded. This command is used in the Cisco IOS exec mode.
rommon-prefUsed in ROMMON command mode. Provides the same information as

upgrade rom-monitor preference command in the Cisco IOS exec mode.

Debugging Commands
Most debugging commands are functional only when Cisco IOS software has crashed or is aborted. If you enter a debugging command and Cisco IOS crash information is not available, the following error message appears:
xxx: kernel context state is invalid, can not proceed.

stack or kProduces a stack trace. contextDisplasy processor context. frameDisplays an individual stack frame. sysretDisplays return information from the last booted system image. This information includes the reason for terminating the image, a stack dump of up to eight frames, and, if an exception is involved, the address where the exception occurred. For example:
rommon 8 > sysret System Return Info: count: 19, reason: a SegV exception pc:0x802b1040, error address: 0x802b1040 Stack Trace: FP: 0x80908398, PC: 0x802b102c FP: 0x809083b0, PC: 0x802b0b88 FP: 0x809083d8, PC: 0x8017039c FP: 0x809083e8, PC: 0x8016f764

Configuration Register Commands

The virtual configuration register resides in NVRAM. You can display or modify the virtual configuration register from either the ROM monitor or the operating system software. To change the virtual configuration register from the ROM monitor, enter the confreg command by itself for menu mode, or enter the new value of the register in hexadecimal.

confreg [hexnum]Changes the virtual configuration register to the value specified. The value is always interpreted as hexadecimal.

Note

Entering confreg without an argument displays the contents of the virtual configuration register and prompts you to alter the contents by describing the meaning of each bit. In either case, the new virtual configuration register value is written into NVRAM, but is not effective until you reset or power-cycle the router. The following display shows an example of the confreg command:
rommon 7 > confreg

Configuration Summary enabled are:

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

C-5

Appendix C Entering the ROM Monitor Mode

Using the ROM Monitor

break/abort has effect console baud: 9600 boot: the ROM Monitor do you wish to change the configuration? y/n [n]: y enable diagnostic mode? y/n [n]: y enable use net in IP bcast address? y/n [n]: enable load rom after netboot fails? y/n [n]: enable use all zero broadcast? y/n [n]: disable break/abort has effect? y/n [n]: enable ignore system config info? y/n [n]: change console baud rate? y/n [n]: y enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400 4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200 change the boot characteristics? y/n [n]: y enter to boot: 0 = ROM Monitor 1 = the boot helper image 2-15 = boot system [0]: 0

[0]:

Configuration Summary enabled are: diagnostic mode break/abort has effect console baud: 9600 boot: the ROM Monitor do you wish to change the configuration? y/n [n]:

You must reset or power cycle for new config to take effect

Using the show rom-monitor Command

Note

The show rom-monitor command is present in the Cisco 3700 series routers only. The command tftpdnld is present in the Cisco 2600 series routers only. The show rom-monitor command displays the current version of the read-only ROM monitor, and if present displays the upgrade version of the ROM monitor. The upgrade version is selected when the system is rebooted. This command runs in the Cisco IOS exec mode. You get the following output, when the read-only ROM monitor is present:
Router# show rom-monitor ReadOnly ROMMON version: System Bootstrap, Version 12.2(4r)XT2, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2001 by cisco Systems, Inc. No upgrade ROMMON programmed or not yet run Currently running ROMMON from ReadOnly region ROMMON from ReadOnly region is selected for next boot Router#

Following is an example of an output when both the read-only and the upgrade versions of the ROM moinitor are present:
Router# show rom-monitor

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

C-6

OL-1957-04

Appendix C

Using the ROM Monitor Entering the ROM Monitor Mode

ReadOnly ROMMON version: System Bootstrap, Version 12.2(4r)XT4, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2001 by cisco Systems, Inc. Upgrade ROMMON version: System Bootstrap, Version 12.2(8r)T1, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2002 by cisco Systems, Inc. Currently running ROMMON from Upgrade region ROMMON from Upgrade region is selected for next boot Router#

Note

You can get the same information if you enter the showmon command in the ROMMON command mode.

Using the upgrade rom-monitor Command

Note

The command upgrade rom-monitor is present in the Cisco 3700 series routers only. To upgrade the ROM monitor to a new version, use the upgrade rom-monitor command. Depending on where the image is located, use the following commands to upgrade the ROM monitor:

upgrade rom-monitor file <URL> upgrade rom-monitor preference <readonly | upgrade>

The upgrade rom-monitors file <URL> command installs the new version of ROM monitor on the router by taking the image from the location indicated in the URL. The image is in the form of .srec file. It then reloads the router. Following is an example of the output when the upgrade version of ROM monitor is located at tftp://223.255.254.254/ajayhn/c3745_RM2.srec:, and the system configuration has not been saved:
Router# upgrade rom-monitor file tftp://223.255.254.254/ajayhn/C3745_RM2.srec Loading ajayhn/C3745_RM2.srec from 223.255.254.254 (via FastEthernet0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [OK - 641719/1283072 bytes] This command will reload the router. Continue? [yes/no]: y System configuration has been modified. Save? [yes/no]: y Building configuration... Erasing boot flash eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee Programming boot flash pppp Now Reloading System Bootstrap, Version 12.2(4r)XT4, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2001 by cisco Systems, Inc. Running new upgrade for first time System Bootstrap, Version 12.2(8r)T1, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2002 by cisco Systems, Inc. c3745 processor with 196608 Kbytes of main memory Main memory is configured to 64 bit mode with parity disabled Upgrade ROMMON initialized rommon 1 >

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

C-7

Appendix C Entering the ROM Monitor Mode

Using the ROM Monitor

Following sample output shows a configuration that has been saved:

Router# upgrade rom-monitor file tftp://223.255.254.254/ajayhn/C3745_RM2.srec Loading ajayhn/C3745_RM2.srec from 223.255.254.254 (via FastEthernet0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [OK - 641719/1283072 bytes] This command will reload the router. Continue? [yes/no]: y Erasing boot flash eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee Programming boot flash pppp Now Reloading System Bootstrap, Version 12.2(4r)XT4, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2001 by cisco Systems, Inc. Running new upgrade for first time System Bootstrap, Version 12.2(8r)T1, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2002 by cisco Systems, Inc. c3745 processor with 196608 Kbytes of main memory Main memory is configured to 64 bit mode with parity disabled Upgrade ROMMON initialized rommon 1 >

Note

The rommon-pref command in the ROMMON command mode provides the same information as the upgrade rom-monitor preference command in the Cisco IOS Exec mod.

Procedures for Recovering Boot and System Images

If your router experiences difficulties and no longer contains a valid Cisco IOS software image in flash memory, you can recover the Cisco IOS image using one of the following ROM monitor commands:

xmodemUse this if the computer attached to your console has a terminal emulator that has xmodem capability. tftpdnldUse this if you have a TFTP server directly connected to the Ethernet 0 port.

Note

The command tftpdnld is present in the Cisco 2600 series routers only.

Using the xmodem Command

The xmodem command establishes a connection between a console and the router console port for disaster recovery if both the boot and system images are erased from flash memory. xmodem [filename]Establishes an xmodem connection between the console and the router. The optional parameter filename specifies the source file containing the Cisco IOS image. Other options include the following:

-cUses cyclic redundancy check (CRC-16) -yUses Ymodem transfer protocol -rCopies the image to DRAM for launch -xDoes not launch image on completion of download

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

C-8

OL-1957-04

Appendix C

Using the ROM Monitor Entering the ROM Monitor Mode

Using the tftpdnld Command

Note

The command tftpdnld is present in the Cisco 2600 series routers only. The tftpdnld command downloads a Cisco IOS software image from a remote server into flash memory using TFTP. tftpdnldBegins the TFTP copy command. The following variables are required:
IP_ADDRESSIP address for the router you are using. IP_SUBNET_MASKSubnet mask for the router you are using. DEFAULT_GATEWAYDefault gateway for the router you are using. TFTP_SERVERIP address of the server from which you want to download the image file. TFTP_FILEName of the file that you want to download. The following variables are optional: TFTP_VERBOSEPrint setting. 0=quiet, 1=progress, 2=verbose. The default is 1. TFTP_RETRY_COUNTRetry count for ARP and TFTP. The default is 7. TFTP_TIMEOUTOverall timeout of the download operation in seconds. The default is 2400

seconds.
TFTP_CHECKSUMPerforms a checksum test on the image. 0=no, 1=yes. The default is 1.

The syntax for specifying the variables is:

VARIABLE_NAME=value

After you specify the variables, you must reenter the tftpdnld command. For example:
rommon rommon rommon rommon rommon rommon rommon rommon 1 2 3 4 5 6 7 8 > > > > > > > > tftpdnld IP_ADDRESS=172.15.19.11 IP_SUBNET_MASK=255.255.255.0 DEFAULT_GATEWAY=172.15.19.1 TFTP_SERVER=172.15.20.10 TFTP_FILE=/tftpboot/c2600-i-mz TFTP_VERBOSE=1 tftpdnld

IP_ADDRESS=172.15.19.11 IP_SUBNET_MASK=255.255.255.0 DEFAULT_GATEWAY=172.15.19.1 TFTP_SERVER=172.15.20.10 TFTP_FILE=/tftpboot/2600-i-mz TFTP_VERBOSE=1 Invoke this command for disaster recovery only. WARNING: all existing data in flash will be lost! Do you wish to continue? y/n: [n]:

Enter y to begin downloading the Cisco IOS software image. When the process is complete, the ROM monitor mode prompt appears on your screen.

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

C-9

Appendix C Entering the ROM Monitor Mode

Using the ROM Monitor

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

C-10

OL-1957-04

INDEX

Numerics
56-kbps DSU/CSU interface, configuring
2-22

Voice Interface Numbering Cisco 3600 series routers interface numbering unit numbers (figure)
1-4 1-9

1-4

A
analog modem interface configuring
3-26 3-28

Cisco 3700 Series Interface Numbering Cisco 3725 Interface Numbering Cisco IOS about
1-13 1-13 1-14 1-13 1-15 1-14 3-8 3-17 1-13 1-9

1-9 1-10

Cisco 3745 router interface numbering

modem country codes configuring

3-5

asynchronous/synchronous serial interface asynchronous interface, configuring atm-dxi map command ATM interface configuring
3-20 3-20 3-21 3-22 3-23 3-48 3-9

command modes enable mode getting help

saving configuration changes undo command undo feature clock rate settings
1-14

configuring PVCs configuring SVCs

codec complexity configuration command modes, Cisco IOS commands configuration register
C-5 1-15

IMA interface configuration

ATM T1/E1 interface configuration

B
benefits boot ROM monitor
C-3 3-50

context

C-5 C-5 3-2 3-7

copy running-config debugging dir

C-3 C-5 1-13, C-4 C-4 3-29 C-4

exec-timeout frame

C
caution symbol, meaning of Cisco 2600 series router WAN Interface Numbering Cisco 2600 series routers interface numbering
1-1 1-2 xiii

half-duplex timer help ping reset meminfo

ROM monitor diagnostics show config

3-2

C-1

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

IN-1

Index

show controllers

3-29 3-26 3-26 3-28

configure channelized T1 ISDN PRI

3-52 3-53

show controllers atm show ima interface atm show interface async show interfaces show line
3-28 3-29 3-29

configure the ISDN D-channel serial interfaces

configure the ISDN D-channel serial interface for E1 modules 3-53 configure the ISDN D-channel serial interface for T1 modules 3-54 configure the ISDN dialer interface
3-56

show protocols show version stack sysret tftpdnld undo xmodem compression hardware PPP
3-49 3-49 C-5 C-5 C-4 C-8 1-14

show running-config
3-29

3-29

configure the LAN interface

3-55 3-54 3-55

configure the loopback interface configuring analog modem

3-26

create the group asynchronous interface

asynchronous/synchronous serial interface asynchronous interface

3-49 3-9

3-5

ATM interface PVCs SVCs

3-20 3-21

3-20

compress command

country codes E1 interface

2-1

3-28 3-14 3-3 2-2 3-17 3-23 3-24 2-5 3-10 3-14

configuration before starting router completing saving timeout verifying

2-23 3-2 3-29 4-2 4-3 1-15 A-23 2-23 2-2

Ethernet interface global parameters codec complexity IMA interface

3-22

high-density voice interface

global parameters

ATM T1/E1 interface IMA group interface interface parameters ISDN-BRI interface ISDN BRI line E1 interface T1 interface
3-57 2-15 3-16 3-15

voice over IP

voice over IP examples configuration, saving configuration example configuration register changing settings configuration tasks
C-5 3-51

ISDN PRI interface

multiflex trunk interface E1 interface T1 interface TDM connect T1 interface

3-14 C-5 3-16 3-15 3-16

3-14

configure modem lines for dial-in and dial-out configure the modem for dial-in configure the modem for dial-out
3-57 3-57 3-57

configure the default IP pool information

T1 (FT1) WAN interface context command

3-18

configure the E1/T1 network module for ISDN PRI 3-51 configure channelized E1 ISDN PRI
3-51

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

IN-2

OL-1957-04

Index

conventions

xii xii

command

C-4 1-13 3-17

conventions, document

help, Cisco IOS

high-density voice interface

D
debugging commands dir command document conventions
xii xii C-3 C-5

codec complexity host name configuring verifying

3-2

show config command

3-2

3-2 3-48

hssi internal-clock command HSSI network module benefits

3-46

document conventions

E
E1/T1 ISDN PRI interface E1 interface configuring enable mode
3-14 1-14 3-48 3-49 2-6, 3-3 3-15, 3-16 3-15, 3-16

configuration disabling fair queueing examples

3-48 3-47 3-48 3-47 3-47 3-48

E1/T1 multiflex trunk interface

invoking ATM

specifying clocking specifying interface task list

3-47 3-46

specifying encapsulation

encapsulation atm-dxi command encapsulation ppp command configuring compression over Ethernet interface, configuring

feature summary

I
IMA interface configuring
3-22 3-23 3-24 1-14

F
feature summary frame command
3-50 C-5

configuring the ATM T1/E1 interface configuring the IMA interface IMA interface configuration
3-24

G
global configuration command mode global parameters configuration
2-2 1-14

interface configuration command mode interface numbering Cisco 2600 series routers Cisco 3600 series routers Cisco 3660 slot 0
1-6, 1-8 1-2 1-1 1-4

H
half-duplex timer commands help
3-7 3-49

WAN and LAN interface cards ISDN BRI switch type, provisioning ISDN BRI line, configuring ISDN PRI interface
2-15

hardware compression, displaying

ISDN BRI interface, configuring

2-15

3-10

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

IN-3

Index

configuring

3-14 3-16 3-15 3-52 2-16

configuring global configuring interface password configuring verifying PPP

3-2

2-2 2-5

E1 configuration T1 configuration

ISDN PRI switch types ISDN switch types

3-12

ISDN provisioning by switch type (table)

show config command

3-2 3-49 3-50

3-2

L
LAN Interface Numbering Cisco 2600 series router
1-2

compression prerequisites

privileged EXEC command mode provisioning ISDN switch types PVC configuration
3-20

1-14 2-15

M
meminfo command
C-4 3-28

R
recovering boot and system images reset command ROM monitor diagnostics router rear view Cisco 3620 (figure) Cisco 3631 (figure) Cisco 3640 (figure) Cisco 3660 (figure)
2-9 2-17 1-5 1-6 1-5 1-5 C-5 C-4 C-8

modem country codes configuring

3-14

multiflex trunk interface E1 configuration T1 configuration TDM connect

3-16 3-15

3-16

N
network modules configuring asynchronous/synchronous interface E1/T1 ISDN PRI interface Ethernet interface ISDN BRI interface serial interface
2-7 2-7 xiii 2-6 2-6 2-12

S
saving configuration changes script, setup See SPID setup command facility setup script, using
2-2 3-2 3-49 1-11 2-2 2-2 1-15

Fast Ethernet interface

service profile identifier

Token Ring interface note symbol, meaning of

P
parameters

show config command

show process cpu command Slot numbering - Cisco 3745

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

IN-4

OL-1957-04

Index

Slot numbering for Cisco 3600 series router slot numbering for Cisco 3725 SPID SPIDs
2-17 2-17 C-5 3-21 1-9

1-4

voice interface numbering Cisco 2600 series routers

1-4

Voice interface numbering for Cisco 3600 Series Routers 1-8 Voice interface numbering for Cisco 3700 Series Routers 1-12 voice over IP configuration examples configuring
4-2 4-10 4-4 4-6 4-8 4-3

stack command Symbols Caution Note Tips

xiii xiii

SVC configuration

Timesaver
xiii

xiii C-5

configuring direct-inward dialing on a BRI port FXS-to-FXS connections linking PBX users with E&M trunk lines

sysret command

PSTN gateway access using FXO connections

T
T1 (FT1) WAN interface, configuring T1 interface configuring
3-14 3-16 C-4 3-2 xiii xiii 3-18

PSTN gateway access using FXO connections in PLAR mode 4-9

W
WAN interface cards Cisco 3600 series slot (figure) WAN Interface Numbering Cisco 2600 series routers
1-2 1-8 1-11

TDM cross-connect configuration tftpdnld command timeout, disabling

WAN interface cards - Cisco 3700 series

timesaver symbol, meaning of tips symbol, meaning of

X U
undo feature, Cisco IOS unit numbers Cisco 3600 series (figure) user EXEC command mode
1-9 1-14 1-14

xmodem command

C-8

V
verifying IMA configuration
3-26 3-29 3-28 1-11

interface configuration modem configuration

Voice Interface cards - Cisco 3700 series

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-04

IN-5

Index

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

IN-6

OL-1957-04

BVI Cisco
No ratings yet
BVI Cisco
6 pages
Case Study Vierendeel Truss
No ratings yet
Case Study Vierendeel Truss
8 pages
PRINCE2 PMBOK ISO Paper PDF
No ratings yet
PRINCE2 PMBOK ISO Paper PDF
10 pages
WAN TECHNOLOGY FRAME-RELAY: An Expert's Handbook of Navigating Frame Relay Networks
From Everand
WAN TECHNOLOGY FRAME-RELAY: An Expert's Handbook of Navigating Frame Relay Networks
Mamta Devi
No ratings yet
Next-Generation switching OS configuration and management: Troubleshooting NX-OS in Enterprise Environments
From Everand
Next-Generation switching OS configuration and management: Troubleshooting NX-OS in Enterprise Environments
Mamta Devi
No ratings yet
Dynamips Tutorial 11032010
No ratings yet
Dynamips Tutorial 11032010
23 pages
Cisco 1721 Datasheet
No ratings yet
Cisco 1721 Datasheet
12 pages
Chapter 4. Using The Command-Line Interface
No ratings yet
Chapter 4. Using The Command-Line Interface
22 pages
ISR Router Family PDF
No ratings yet
ISR Router Family PDF
26 pages
CCNA Labs
No ratings yet
CCNA Labs
27 pages
CCNP Route Eigrp Lab
No ratings yet
CCNP Route Eigrp Lab
2 pages
ANA371RefGuide (Cisco Pseudo Wire, Carrier Ethernet)
No ratings yet
ANA371RefGuide (Cisco Pseudo Wire, Carrier Ethernet)
1,306 pages
NLI's Cisco CCIE Security Lab Guide Sample Pages
No ratings yet
NLI's Cisco CCIE Security Lab Guide Sample Pages
16 pages
VLAN & Port Types: Khawar Butt Ccie # 12353 (R/S, Security, SP, DC, Voice, Storage & Ccde)
No ratings yet
VLAN & Port Types: Khawar Butt Ccie # 12353 (R/S, Security, SP, DC, Voice, Storage & Ccde)
16 pages
Lab-00-01 - Configure Cisco 3600 Router To Use As A Switch in GNS3
No ratings yet
Lab-00-01 - Configure Cisco 3600 Router To Use As A Switch in GNS3
1 page
QoS CLI
No ratings yet
QoS CLI
12 pages
BRKNMS 3134 PDF
No ratings yet
BRKNMS 3134 PDF
155 pages
Cisco IOS ISO CLNS Command Reference
No ratings yet
Cisco IOS ISO CLNS Command Reference
179 pages
2013 10 03 NetFlow JiriTesar
No ratings yet
2013 10 03 NetFlow JiriTesar
38 pages
Cisco IOS Software Release 15.0 (1) M
No ratings yet
Cisco IOS Software Release 15.0 (1) M
84 pages
Wireless (Chapter 5)
No ratings yet
Wireless (Chapter 5)
165 pages
Spanning Tree Protocol
No ratings yet
Spanning Tree Protocol
9 pages
Skollar Cisco 7600 Series Product Essentials
No ratings yet
Skollar Cisco 7600 Series Product Essentials
27 pages
Cisco Firepower Next-Generation Firewall: Performance Highlights
No ratings yet
Cisco Firepower Next-Generation Firewall: Performance Highlights
12 pages
Lab 3: Basic EIGRP Configuration Lab: Topology Diagram
No ratings yet
Lab 3: Basic EIGRP Configuration Lab: Topology Diagram
4 pages
07-BCMSN-Layer 3 Switching PDF
No ratings yet
07-BCMSN-Layer 3 Switching PDF
7 pages
Deploying Ipv6 in Branch Networks: Last Updated: April 8, 2011
No ratings yet
Deploying Ipv6 in Branch Networks: Last Updated: April 8, 2011
40 pages
Cisco IOS IP SLAs Configuration Guide
No ratings yet
Cisco IOS IP SLAs Configuration Guide
332 pages
CCNP v6 Route Lab 2.1
No ratings yet
CCNP v6 Route Lab 2.1
13 pages
Switch Stack Update: Prerequisites
No ratings yet
Switch Stack Update: Prerequisites
10 pages
Upgrade Cisco Ios
No ratings yet
Upgrade Cisco Ios
3 pages
Cisco Router Configuration Tutorial PDF
No ratings yet
Cisco Router Configuration Tutorial PDF
8 pages
WLC Config Best Practice
No ratings yet
WLC Config Best Practice
46 pages
Cisco 800 Series PDF
No ratings yet
Cisco 800 Series PDF
16 pages
Cisco AP Mobility Express Deployment Guide
No ratings yet
Cisco AP Mobility Express Deployment Guide
96 pages
CISCO QoS
No ratings yet
CISCO QoS
150 pages
Cisco IOS Cisco XR Difference Guide
No ratings yet
Cisco IOS Cisco XR Difference Guide
40 pages
Router Fundamentals
100% (4)
Router Fundamentals
22 pages
Cisco IOS XR Advanced System Command Reference For The Cisco CRS Router, Release 4.2.x
No ratings yet
Cisco IOS XR Advanced System Command Reference For The Cisco CRS Router, Release 4.2.x
604 pages
B Cisco APIC Layer 2 Configuration Guide
No ratings yet
B Cisco APIC Layer 2 Configuration Guide
256 pages
Free Download: BGP Lab Manual PDF
No ratings yet
Free Download: BGP Lab Manual PDF
5 pages
Ipsec Presentation
No ratings yet
Ipsec Presentation
40 pages
Lab3 Cciesecv4 Questionset
No ratings yet
Lab3 Cciesecv4 Questionset
32 pages
4 Interview Ques - 1000 (Updated Sampath)
No ratings yet
4 Interview Ques - 1000 (Updated Sampath)
144 pages
Cisco 3750 Configuration Guide
No ratings yet
Cisco 3750 Configuration Guide
1,010 pages
Brief Previliage Cisco Command
No ratings yet
Brief Previliage Cisco Command
3 pages
Configuring Cisco Asav in GNS3
No ratings yet
Configuring Cisco Asav in GNS3
9 pages
Designing A Scalable Network Infrastructure
No ratings yet
Designing A Scalable Network Infrastructure
33 pages
Cisco Nexus
No ratings yet
Cisco Nexus
7 pages
101 - Exam 300-115
No ratings yet
101 - Exam 300-115
11 pages
Cisco Certified Network Professional (CCNP) : Course Outline
No ratings yet
Cisco Certified Network Professional (CCNP) : Course Outline
2 pages
Troubleshooting Case Study: SECHNIK Networking: CCNP TSHOOT: Maintaining and Troubleshooting IP Networks
No ratings yet
Troubleshooting Case Study: SECHNIK Networking: CCNP TSHOOT: Maintaining and Troubleshooting IP Networks
37 pages
In Depth Guide to IS-IS Routing: Learn Intermediate System to Intermediate System Routing from scratch
From Everand
In Depth Guide to IS-IS Routing: Learn Intermediate System to Intermediate System Routing from scratch
Mamta Devi
No ratings yet
Configuring IPCop Firewalls: Closing Borders with Open Source
From Everand
Configuring IPCop Firewalls: Closing Borders with Open Source
Barrie Dempster
No ratings yet
Installing SQL Server 2012 Step by Step
From Everand
Installing SQL Server 2012 Step by Step
Stephen Thomas
No ratings yet
Alcatel-Lucent Service Routing Architect (SRA) Self-Study Guide: Preparing for the BGP, VPRN and Multicast Exams
From Everand
Alcatel-Lucent Service Routing Architect (SRA) Self-Study Guide: Preparing for the BGP, VPRN and Multicast Exams
Glenn Warnock
No ratings yet
Cacti 0.8 Beginner's Guide
From Everand
Cacti 0.8 Beginner's Guide
Thomas Urban
No ratings yet
Cisco 7600 Configuration Guide
No ratings yet
Cisco 7600 Configuration Guide
572 pages
Cisco ConfiguratioGuide SW4500 IOS
No ratings yet
Cisco ConfiguratioGuide SW4500 IOS
608 pages
Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide
No ratings yet
Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide
608 pages
Config Router Cisco 7600 Series
No ratings yet
Config Router Cisco 7600 Series
1,290 pages
GasRanger Models Specs
No ratings yet
GasRanger Models Specs
2 pages
Catalogo Toshiba
No ratings yet
Catalogo Toshiba
12 pages
13-4 Cylinder Block Crankshaft and Flywheel Service PDF
100% (1)
13-4 Cylinder Block Crankshaft and Flywheel Service PDF
33 pages
Index of Trade Names and Suppliers of Flame Retardants: Q 2006 by Taylor & Francis Group, LLC
No ratings yet
Index of Trade Names and Suppliers of Flame Retardants: Q 2006 by Taylor & Francis Group, LLC
2 pages
Valves PDF - Goel Scientific
No ratings yet
Valves PDF - Goel Scientific
3 pages
E-Installation 04 11 en
No ratings yet
E-Installation 04 11 en
28 pages
CS SGC 004
No ratings yet
CS SGC 004
4 pages
Word Processors: - Microsoft Word - Corel Wordperfect - Word Star - Lotus Wordpro
No ratings yet
Word Processors: - Microsoft Word - Corel Wordperfect - Word Star - Lotus Wordpro
10 pages
Narmada Valley Development Authority Narmada Bhawan, 59 Arera Hills Bhopal (M.P.)
No ratings yet
Narmada Valley Development Authority Narmada Bhawan, 59 Arera Hills Bhopal (M.P.)
3 pages
Zoho Round 2 LP
No ratings yet
Zoho Round 2 LP
111 pages
SCC Presn
No ratings yet
SCC Presn
30 pages
Design and Planning Manual For Cost Effective Welding
100% (1)
Design and Planning Manual For Cost Effective Welding
131 pages
Organization Charts
100% (1)
Organization Charts
14 pages
Performance Calculation of The Train Part 3 1708607233
No ratings yet
Performance Calculation of The Train Part 3 1708607233
14 pages
Psychrometric Chart Basics
No ratings yet
Psychrometric Chart Basics
57 pages
Standard Design and Mass Balance of 10 KLF FSTP, R0
No ratings yet
Standard Design and Mass Balance of 10 KLF FSTP, R0
10 pages
Jsa For Trenching - Cable Laying
No ratings yet
Jsa For Trenching - Cable Laying
1 page
Ieee STD c57
33% (3)
Ieee STD c57
5 pages
Acceptance Criteria AWS API ASME
No ratings yet
Acceptance Criteria AWS API ASME
14 pages
Dao 2016-08 PDF
100% (1)
Dao 2016-08 PDF
34 pages
Lift Balancing
100% (1)
Lift Balancing
3 pages
Bonding in Transition Metal Complexes
100% (1)
Bonding in Transition Metal Complexes
41 pages
Ank White
No ratings yet
Ank White
16 pages
GEOD1016ra Mla e PDF
No ratings yet
GEOD1016ra Mla e PDF
24 pages
Multi Row Function SQL
100% (1)
Multi Row Function SQL
8 pages
Project Management Report
No ratings yet
Project Management Report
36 pages
Excerpt Construction Smaller
14% (7)
Excerpt Construction Smaller
3 pages
TSTP EMF Measurement PDF
No ratings yet
TSTP EMF Measurement PDF
81 pages

Cisco 2600 Router Command Reference

Uploaded by

Cisco 2600 Router Command Reference

Uploaded by

Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

Text Part Number: OL-1957-04

Objectives Audience Organization

Document Conventions Additional Information

Configuring Voice-over-IP 4-1 Voice-over-IP Prerequisites Configuring the Voice Interface

Formatting the Compact Flash Memory Cards

Using the ROM Monitor

boldface screen font < [ > ]

Preface Additional Information

Cisco.com Documentation CD-ROM Cisco Technical Assistance Center (TAC)

Related and Referenced Documents

Preface Related and Referenced Documents

To Access Online User Documentation (PDF and HTML Formats):

Access User Documentation on the Documentation CD-ROM (HTML format only):

Related and Referenced Documents

Cisco Product Cisco 2600 series routers

Cisco 3600 series routers

Preface Related and Referenced Documents

Related and Referenced Documents (continued)

Cisco Product Cisco 3700 series routers

Cisco IOS software

Preface Obtaining Documentation

Related and Referenced Documents (continued)

Cisco Product Other documents

World Wide Web

http://www.cisco.com http://www-china.cisco.com http://www-europe.cisco.com

Preface Obtaining Technical Assistance

Obtaining Technical Assistance

Preface Obtaining Technical Assistance

Technical Assistance Center

Contacting TAC by Using the Cisco TAC Website

Contacting TAC by Telephone

Preface Obtaining Technical Assistance

P1 and P2 level problems are defined as follows:

Preface Obtaining Technical Assistance

Understanding Interface Numbering and Cisco IOS Software Basics

Understanding Interface Numbering

Cisco 2600 Series Interface Numbering

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

Fast Ethernet Network (10/100) Module Slot 1 1 1 1 2 1 1 1 1 1 2 2 1 1 2 2 2 1 1 1 1 1 1 1 1 1

WAN Interface Card Slots 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3

Advanced Integration Module Slots 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2

The number and type of interfaces vary depending on the router.

WAN and LAN Interface Numbering

The numbering format is Interface-type Slot-number/Interface-number. Two examples are:

Figure 1-2 below shows a router of 2 RU height with:

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

number in the WIC is numbered Serial 0/0.

Voice Interface Numbering in Cisco 2600 Series Routers

Cisco 3600 Series Interface Numbering

Cisco 3600 Series Router Slot Numbering

Cisco 3660 Router Rear View

Cisco 3640 Router Rear View

Cisco 3620 Router Rear View

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

Cisco 3631 Router Rear View

Example of the Cisco 3631 Router Interface Numbering

interface in the WIC is numbered serial 0/0.

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

WAN Interface Card Slots

Cisco 3600 Series Router Unit Numbering

Cisco 3600 Series Routers Voice Interface Numbering

Cisco 3700 Series Interface Numbering

Cisco 3725 Router Interface Numbering

Cisco 3725 Router Slot Numbering

The slot numbers are as follows:

0 for all built-in interfaces 0 for all WIC interfaces

Chapter 1 Understanding Interface Numbering

Understanding Interface Numbering and Cisco IOS Software Basics

Figure 1-10 Cisco 3725 Router Rear View

the WIC is numbered Serial 0/0.

Cisco 3745 Router Interface Numbering