Network Mini Dome Cameras

Quick Guide

V1.01
 Waterproof Requirements
Please waterproof cables in accordance with the following instructions. User shall assume all
responsibility for device damage caused by water due to improper waterproof measures.

NOTE!

• Before you start, connect all the needed cables and cut off the copper wires for the cables that
you don't use.
• Please use self-adhesive waterproof tape (supplied with some products) to protect the cables.
• Use waterproof components to protect the network cable. Waterproof the power cable
separately if you don’t use it. The video cable does not need waterproof treatment.

1. Use insulation tape (not included in the package) to insulate the connection part of each cable.
Connection part

Insulation tape

2. Waterproof the cables with self-adhesive waterproof tape.

(1) Fully stretch the waterproof tape at both ends.
(2) Wrap the connection part and the cable ends tightly with waterproof tape. Make sure the tape is fully
stretched during the process.
(3) Tighten the tape at both ends to prevent water leakage.
Tighten Tighten
Tighten Tighten

Wrap the used cables separately Waterproof tape

Wrap the unused cables
together into a bundle

3. Install the supplied waterproof components to the network cable in sequence.

CAUTION!
You need to mount the rubber ring onto the network cable interface first.

4. If your camera has a DC cable and you will not use it, insert the plug into the interface.

1
 DC interface

Plug
5. (Optional) After the waterproof treatment is completed, put the cables into a waterproof junction box
(purchased separately).

CAUTION!

• The cable connector must not be exposed and must be kept away from water.
• Restore and fasten the device after dismounting.
• Place the power adapter in a power distribution box.

1 Packing List
Contact your local dealer if the package is damaged or incomplete. The package contents may vary with
device model.

No. Name Qty Unit

1 Camera 1 PCS

2 User manual 1 Set

3 Mount accessories 1 Set

2 Safety Instructions
Installation and removal of the unit and its accessories must be carried out by qualified personnel. You
must read all of the Safety Instructions supplied with your equipment before installation and operation.

2.1 Installation
 This device is a class A product and may cause radio interference. Take measures if necessary.
 Make sure the camera operates in an environment where the temperature and humidity meet
requirements. Keep the camera from excessive pressure, vibration, moisture, dust, and intensive
electromagnetic radiation.
 Use a power adapter or a PoE device that meets requirements. Otherwise, the device may be
damaged.
 Make sure the length of the power cable between the power adapter and the camera is not too long,
otherwise the voltage of the camera is lowered, causing the camera to work abnormally. If it is
required to lengthen the power cable, lengthen the cable between the power adapter and the
mains.
 Do not hold the tail cable by hand for weight bearing. Otherwise, the cable connector of the camera
could be loosened.

2
  When connecting to an external interface, use an existing connection terminal, and ensure that the
cable terminal (latch or clamp) is in good condition and properly fastened. Ensure that the cable is
not tense during mounting, with a proper margin reserved to avoid poor port contact or loosening
caused by shock or shake.
 The connectors of the tail cable must not be exposed. The bar cavity, waterproof box, corrugated
pipe and PVC pipe must be fully sealed to protect the connectors from water. The waterproof
components for the RJ45 plug must be used properly to protect the network cable from water.
 During the process of transportation, special attention is required for the protection of the
transparent dome cover to prevent friction, scratch and contamination, etc. In order to keep the
cover clean, do not remove the protective film on the cover during mounting. After mounting is
finished, remove the film before the device is powered on.
 Contact professionals for maintenance information. Do not attempt to dismantle the device by
yourself. We shall not assume any responsibility for problems caused by unauthorized repair or
maintenance.

2.2 Maintenance
 Caution: There will be risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
 If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a rubber
dust blowing ball.
 If there is grease or a dust stain on the front glass surface, clean the glass surface gently from the
center outward using lens cleaning cloth. If the grease or the stain still cannot be removed, use lens
cleaning cloth dipped with detergent and clean the glass surface gently until it is removed.
 Do not use organic solvents, such as benzene or ethanol when cleaning the transparent dome cover.
 Make sure the lens cleaning cloth is clean itself.

• Never look at the transmit laser while the power is on. Never look
directly at the fiber ports and the fiber cable ends when they are
powered on.
• Use of controls or adjustments to the performance or procedures
other than those specified herein may result in hazardous laser
emissions.

3 Appearance
3.1 Dimensions
The figures in the manual are for your reference only. The actual appearance may vary with the product
model.

3
 96.6mm
3.8"
118.1mm
4.6"

3.2 Cable Connection

The appearance and tail cable may vary with device model.

5
2

IP
Network

No. Description No. Description

1 Base plate 2 Housing

3 Lens 4 Infrared LED

5 Power interface (12 VDC) 6 Ethernet interface

NOTE!
For specifications, see the latest product datasheet.

4 Mount Your Camera

You can adopt ceiling mount or wall mount and purchase hardware accessories by yourself. The following

4
part takes ceiling mount as an example. Wall mount is similar to ceiling mount and therefore is omitted
here.
1. Attach the sticker to ceiling, and then drill 30-mm deep guide holes using a drill bit (6mm or 6.5mm
in diameter) according to the sticker.

2. Insert the plastic anchors.

 Drill a hole to lead cables out of the ceiling.
 Knock in plugs.

3. Detach the housing from the base plate with the marks aligned.

Install mark

Install mark

4. Install the base plate and the camera. Connect cable and protect it with waterproof tape and attach
dome to ceiling with taping screws.

5
 slot

5. Mount your camera. Mount the housing with install mark aligned

Install mark

Install mark

6. Adjust the monitoring direction. Rotate the camera to desired monitoring direction.

6
 The above steps are for concealed installation. For an open installation, lead the cables from the open
slot on the base plate.

NOTE!
When you adopt open installation, make sure that the cables can be led out through the open
slot on the base plate and screw the dome to the wall as shown in step 3.

5 Access Your Camera

Before you begin, check that:
 Your camera is operating properly and connected to the network.
 The PC you are using is installed with Internet Explorer 7.0 or later.
Follow these steps to access your camera through the Web:
1. Open your browser, input the IP address 192.168.1.13 of your camera in the address bar and then
press Enter to open the login page.
2. Enter the username and password (admin/123456 by default) and then click Login.

NOTE!

• DHCP is enabled by default. If a DHCP server is used in your network, your camera may be
assigned an IP address, and you need to use the assigned IP address to log in.
• You may need to install a plug-in at your first login. Please follow the on-screen instructions to
complete the installation and then open the browser again to log in.
• The default password is intended only for your first login. To ensure security, please change the
password after your first login. You are strongly recommended to set a strong password of at
least nine characters including all three elements: digits, letters and special characters.
• If the password has been changed, please use the new password to log in.

7
Disclaimer and Safety Warnings
Copyright Statement
No part of this manual may be copied, reproduced, translated or distributed in any form or by any means without
prior consent in writing from our company (referred to as us hereafter).
The product described in this manual may contain proprietary software owned by our company and its possible
licensors. Unless permitted, no one is allowed to copy, distribute, modify, abstract, decompile, disassemble,
decrypt, reverse engineer, rent, transfer, or sublicense the software in any form or by any means.
Export Compliance Statement
Our company complies with applicable export control laws and regulations worldwide, including that of the
People's Republic of China and the United States, and abides by relevant regulations relating to the export, re-
export and transfer of hardware, software and technology. Regarding the product described in this manual, our
company asks you to fully understand and strictly abide by the applicable export laws and regulations worldwide.
Privacy Protection Reminder
Our company complies with appropriate privacy protection laws and is committed to protecting user privacy.
You may want to read our full privacy policy at our website and get to know the ways we process your personal
information. Please be aware, using the product described in this manual may involve the collection of personal
information such as face, fingerprint, license plate number, email, phone number, GPS. Please abide by your local
laws and regulations while using the product.
About This Manual
 This manual is intended for multiple product models, and the photos, illustrations, descriptions, etc, in this
manual may be different from the actual appearances, functions, features, etc, of the product.
 This manual is intended for multiple software versions, and the illustrations and descriptions in this manual
may be different from the actual GUI and functions of the software.
 Despite our best efforts, technical or typographical errors may exist in this manual. Our company cannot be
held responsible for any such errors and reserves the right to change the manual without prior notice.
 Users are fully responsible for the damages and losses that arise due to improper operation.
 Our company reserves the right to change any information in this manual without any prior notice or
indication. Due to such reasons as product version upgrade or regulatory requirement of relevant regions, this
manual will be periodically updated.
Disclaimer of Liability
 To the extent allowed by applicable law, in no event will our company be liable for any special, incidental,
indirect, consequential damages, nor for any loss of profits, data, and documents.
 The product described in this manual is provided on an "as is" basis. Unless required by applicable law, this
manual is only for informational purpose, and all statements, information, and recommendations in this
manual are presented without warranty of any kind, expressed or implied, including, but not limited to,
merchantability, satisfaction with quality, fitness for a particular purpose, and noninfringement.
 Users must assume total responsibility and all risks for connecting the product to the Internet, including, but
not limited to, network attack, hacking, and virus. We strongly recommend that users take all necessary
measures to enhance the protection of network, device, data and personal information. Our company
disclaims any liability related thereto but will readily provide necessary security related support.
 To the extent not prohibited by applicable law, in no event will our company and its employees, licensors,
subsidiary, affiliates be liable for results arising out of using or inability to use the product or service, including,
not limited to, loss of profits and any other commercial damages or losses, loss of data, procurement of
substitute goods or services; property damage, personal injury, business interruption, loss of business
information, or any special, direct, indirect, incidental, consequential, pecuniary, coverage, exemplary,
subsidiary losses, however caused and on any theory of liability, whether in contract, strict liability or tort
(including negligence or otherwise) in any way out of the use of the product, even if our company has been
advised of the possibility of such damages (other than as may be required by applicable law in cases involving
personal injury, incidental or subsidiary damage).

8
 To the extent allowed by applicable law, in no event shall our total liability to you for all damages for the
product described in this manual (other than as may be required by applicable law in cases involving personal
injury) exceed the amount of money that you have paid for the product.
EU Authorised Representative
UNV Technology EUROPE B.V. Room 2945,3rd Floor,Randstad 21-05 G,1314 BD,Almere,Netherlands.
Network Security
Please take all necessary measures to enhance network security for your device.
The following are necessary measures for the network security of your device:
 Change default password and set strong password: You are strongly recommended to change the default
password after your first login and set a strong password of at least nine characters including all three
elements: digits, letters and special characters.
 Keep firmware up to date: It is recommended that your device is always upgraded to the latest version for the
latest functions and better security. Visit our official website or contact your local dealer for the latest firmware.
The following are recommendations for enhancing network security of your device:
 Change password regularly: Change your device password on a regular basis and keep the password safe.
Make sure only the authorized user can log in to the device.
 Enable HTTPS/SSL: Use SSL certificate to encrypt HTTP communications and ensure data security.
 Enable IP address filtering: Allow access only from the specified IP addresses.
 Minimum port mapping: Configure your router or firewall to open a minimum set of ports to the WAN and keep
only the necessary port mappings. Never set the device as the DMZ host or configure a full cone NAT.
 Disable the automatic login and save password features: If multiple users have access to your computer, it is
recommended that you disable these features to prevent unauthorized access.
 Choose username and password discretely: Avoid using the username and password of your social media,
bank, email account, etc, as the username and password of your device, in case your social media, bank and
email account information is leaked.
 Restrict user permissions: If more than one user needs access to your system, make sure each user is granted
only the necessary permissions.
 Disable UPnP: When UPnP is enabled, the router will automatically map internal ports, and the system will
automatically forward port data, which results in the risks of data leakage. Therefore, it is recommended to
disable UPnP if HTTP and TCP port mapping have been enabled manually on your router.
 SNMP: Disable SNMP if you do not use it. If you do use it, then SNMPv3 is recommended.
 Multicast: Multicast is intended to transmit video to multiple devices. If you do not use this function, it is
recommended you disable multicast on your network.
 Check logs: Check your device logs regularly to detect unauthorized access or abnormal operations.
 Physical protection: Keep the device in a locked room or cabinet to prevent unauthorized physical access.
 Isolate video surveillance network: Isolating your video surveillance network with other service networks helps
prevent unauthorized access to devices in your security system from other service networks.
Safety Warnings
The device must be installed, serviced and maintained by a trained professional with necessary safety knowledge
and skills. Before you start using the device, please read through this guide carefully and make sure all applicable
requirements are met to avoid danger and loss of property.
Storage, Transportation, and Use
 Store or use the device in a proper environment that meets environmental requirements, including and not
limited to, temperature, humidity, dust, corrosive gases, electromagnetic radiation, etc.
 Make sure the device is securely installed or placed on a flat surface to prevent falling.
 Unless otherwise specified, do not stack devices.
 Ensure good ventilation in the operating environment. Do not cover the vents on the device. Allow adequate
space for ventilation.
 Protect the device from liquid of any kind.
 Make sure the power supply provides a stable voltage that meets the power requirements of the device. Make
sure the power supply's output power exceeds the total maximum power of all the connected devices.
9
 Verify that the device is properly installed before connecting it to power.
 Do not remove the seal from the device body without consulting our company first. Do not attempt to service
the product yourself. Contact a trained professional for maintenance.
 Always disconnect the device from power before attempting to move the device.
 Take proper waterproof measures in accordance with requirements before using the device outdoors.
Power Requirements
 Install and use the device in strict accordance with your local electrical safety regulations.
 Use a UL certified power supply that meets LPS requirements if an adapter is used.
 Use the recommended cordset (power cord) in accordance with the specified ratings.
 Only use the power adapter supplied with your device.
 Use a mains socket outlet with a protective earthing (grounding) connection.
 Ground your device properly if the device is intended to be grounded.
Battery Use Caution
 When battery is used, avoid:
 Extremely high or low temperature and air pressure during use, storage and transportation;
 Battery replacement.
 Use the battery properly. Improper use of the battery such as the following may cause risks of fire, explosion
or leakage of flammable liquid or gas.
 Replace battery with an incorrect type;
 Dispose of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery;
 Dispose of the used battery according to your local regulations or the battery manufacturer's instructions.
Avertissement de l’utilisation de la batterie
 Lorsque utiliser la batterie, évitez:
 Température et pression d'air extrêmement élevées ou basses pendant l'utilisation, le stockage et le
transport.
 Remplacement de la batterie.
 Utilisez la batterie correctement. Mauvaise utilisation de la batterie comme celles mentionnées ici, peut
entraîner des risques d’incendie, d’explosion ou de fuite liquide de gaz inflammables.
 Remplacer la batterie par un type incorrect;
 Disposer d’une batterie dans le feu ou un four chaud, écraser mécaniquement ou couper la batterie;
 Disposer la batterie utilisée conformément à vos règlements locaux ou aux instructions du fabricant de la
batterie.
Regulatory Compliance
FCC Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own
expense.

10
LVD/EMC Directive
This product complies with the European Low Voltage Directive
2014/35/EU and EMC Directive 2014/30/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical &
Electronic Equipment (WEEE) Directive and must be disposed of in a
responsible manner.
Battery Directive-2013/56/EC
Battery in the product complies with the European Battery Directive
2013/56/EC. For proper recycling, return the battery to your supplier or to a
designated collection point.

11